Search Documents

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig. 1). The average fuel requirement per barrel of crude oil refined has remained virtually stationary for the past 3 years. Thus in 1937 the average was 562,000 B.t.u., in is it rose to 567,000 B.t.u., and in 1939 it declined to 557,000 B.t.u. she largest gains in fuel economy cane a decade or so ago on the widespread introduction of heat exchanges and pipe stills. In recent years many successful innovations in heat saving have been adopted, but the combined effect of those is completely masked by the degree to which the capacity is utilized. Some heat requirements are relatively inelastic, so the average consumption per barrel of crude oil refined tends s to increase when the operating ratio (crude runs divided by capacity) declines and vice versa. In 1939 crude runs to stills increased 6 percent (from 1,165,015,000 barrels in 1938 to 1,237,840,000 in 1939) compared with a decline of about 2 percent in 1938. The operating ratio in 1939 was 82 percent compared it's 78 percent in 1938.]

Jan 1, 1941

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking in the past few years have focused the attention of the Bureau of Mines on the need for safety standards for such operations. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1957

By W. E. Robinson

Samples of raw oil shale and kerogen concentrates were oxidized by alkaline potassium permanganate, air, nitric acid, oxygen, and ozone to obtain information about the chemical structure of organic kerogen in oil shale. In one test, oil shale and oil-shale products were oxidized exhaustively with alkaline potassium permanganate, and the distribution of the organic carbon in the final oxidation products was determined. Comparing results of this oxidation with those obtained from other carbonaceous materials and known compounds gave information about the structure of kerogen. Alkaline potassium permanganate oxidation also was used partly to degrade kerogen into soluble products for characterization purposes. Structures present in these degradation products were indicative of type structures originally present in the kerogen. Nitric acid, oxygen, and ozone were used also for partly degrading kerogen to soluble oxidation products. Carbon-balance oxidation tests using alkaline potassium permanganate showed that Colorado oil-shale kerogen differs from many other carbonaceous materials such as coal and kerogens from other areas. Composition of the degradation products indicated that Colorado oil-shale kerogen is predominantly cycloparaffinic and saturated heterocyclic structures with some long-chain paraffinic and aromatic structures present. The ring systems may be connected through short carbon chains or bridges containing oxygen, nitrogen, and sulfur.

Jan 1, 1963

By D. N. Tallman

The electrokinetic properties of MgO have been utilized to simultaneously filter suspended solids and remove trace amounts of dissolved heavy metals from synthetic mine water. Greater than 95 pct removal of metals from influent at neutral pH containing 1 to 6 mg/L of dissolved Cd, Cu, Mn, Ni, and Zn can be routinely achieved by filtering through a granular bed of MgO at flow rates typical of rapid sand filtration (0.3 cm/s). Filtrate concentrations of most metals can be maintained below 0.1 mg/L for 160 bed volumes or more loading. The more mobile metals (those with larger solubility products) are more difficult to remove, and are strongly bonded to the MgO granules so that chemical stripping with chelating agent is required to clean the bed. Less mobile ions are easily removed by the filter and are effectively stripped by conventional filter backwashing. The fraction of metals recovered by chemically stripping the loaded MgO filters correlates to the zero points of charge of the metals. This process may be applicable to removal and recovery of trace amounts of heavy metals in mine drainage that is partly neutralized by liming. Also, since many of these metals are critical and strategic, the technique can be adapted not only to recycle process water from mineral and milling waste streams, but also to reclaim their metal values.

Jan 1, 1986

By R. D. Berkenkotter

This report describes a weighted method for evaluating the mean and variance of assay data from samples of different length . The method , which produces unbiased estimates from which valid confidence limits can be computed , is appropriate for bedded deposits of variable bed thickness and for vein deposits of variable vein width . Assay data from the bedded Florida phosphate deposit is used to illustrate the procedure .

Jan 1, 1964

By J. L. Eakin

A method was developed by the Bureau of Mines in the laboratory and in the field to relieve capillary waterblocks in gas wells. Impaired gas permeability was improved by this inexpensive chemical treatment which lowers the surface tension of the water held in the capillaries of the formation. Effectiveness of the alcohol-surfactant treatment was tested with a variety of chemicals and with sandstone cores cut from rocks having relatively low permeability. Field tests on 20 gas-producing and storage wells demonstrated the effectiveness and limitations of the method. The productive capacity of some wells was doubled by the treatment. The final test was evaluated by the neutron logging technique for measuring changes in apparent liquid saturation. Maximum apparent liquid saturation was reduced by 52 percent; gas production rate increased from 2.3 to 3.5 MMcfd (million cubic feet per day).

Jan 1, 1965

By J. S. Dunning

The objective of this research by the U.S. Bureau of Mines was to determine the effects of AI additions on the sulfidation resistance of Fe-Cr-Ni alloys. A series of Fe-Cr-Ni alloys with and without -additions of 4 pet AI were tested in a wet S vapor atmosphere at 677 C. A study of the morphology and composition of corrosion scales indicated a different corrosion mechanism for AI-free alloys compared with AI-containing alloys. Aluminum-containing alloys formed a compact, tightly adherent layer at the metal-scale interface that reduced corrosion rates by a factor of 3 to 10 compared with that of AI-free alloys. The thin, adherent AI-containing scale limited inward diffusion of 0 and S to the base metal and outward diffusion of Ni from the base metal. Aluminum-containing alloys formed a three-layer scale in oxidizing-S environments, while AI-free alloys formed a less protective two-layer scale.

Jan 1, 1989

By J. P. Powell

This report provides information on the techniques and results obtained on representative waterflooding projects in Cowley County, Kans. Records show that waterflooding was begun as early as 1935, but not until 1948 was the method expanded. The greater depths to the oil-producing formations in this area compared to those in eastern Kansas undoubtedly delayed the widespread use of secondary-recovery methods. This report presents a discussion of four waterflooding projects in Cowley County, Kans. The locations of these projects are shown in figure 1. The projects have been in operation from 1 to 7 years and have produced more than 1 million barrels of additional oil by injecting 11.5 million barrels of water. The projects are designed to take advantage of elevation and height of the separator tank to collect by gravity flow the produced brine at the respective treating or storage tanks. The closed-type water system is used on three of the projects and an open-type water conditioning system on the fourth. On one of the projects, which was drilled along a narrow shoestring formation, alternate well, were converted to input wells. However, most of the input wells for flooding converted producing wells.

Jan 1, 1958

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By H. H. Schrenk

There is a need for a method of determining benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the Smyth modification of the Elliott and Dalton procedure. This depends on the nitration of the benzene to m-dinitrobenzene, reduction to phenylenediamine with an excess of standard titanous chloride solution, and back titration with a standard ferric ammonium sulphate solution. This method has the disadvantages of being somewhat time-consuming and cumbersome; it requires considerable apparatus, and a special modification is necessary in the presence of toluene. Recently Cook and Ficklen have published a method based on the oxidation of benzene with hydrogen peroxide in the presence of iron salts. This method requires the use of solid carbon dioxide to freeze out the benzene. The reaction Which produces the color is complex; and only approximate quantitative estimations can be made, except in a very narrow range.

Jan 1, 1935

By H. H. Schrenk

[There is a need for method of determining: benzene vapor in air which is simple and accurate and suitable for making industrial hygiene surveys. The most widely used method in this country is the modification of the Elliott and Dalton6/ procedure. This depends on the nitration of the benzene to reduction to phenylenediamine with all excesses of standard titanous chloride; solution, and titration with e standard ferric ammonium sulphite solution. This method has the disadvantages of being what time consulting: and cumbersome it requires considerable apparatus, and a special modification is necessary in the presence of toluene.]

Jan 1, 1935

This report was prepared by Jacob Tolsma and Arnold N. Johnson of the Uniroya 1 Research Center, Wayne, New Jersey. The valuable assistance and suggestions of the project officers, Mr. Ronald D. Hill, Dr. David R. Maneval and Mr. John J. Buscavage is gratefully acknowledged. The authors are grateful to the following Uniroyal personnel: Mr. Daniel Shichman, manager of Engineering Research, and Dr. Emmanuel G. Kontos, manager of the Polymer Physics Research for their direction, encouragement and suggestions regarding the experimental work, and Mr. Mark Olson for the design of the hollow auger soil sampler. We also wish to gratefully acknowledge the efforts and contributions of ideas proposed by our consultants, Dr. Frank T. Caruccio, assistant professor of geology at State University College, New Paltz, New York, and Dr. Pa Ho Hsu, associate professor of soil chemistry, Rutgers University , New Brunswick, New Jersey.

Jan 1, 1972

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures area discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of mining modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mine is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By R. V. Lundquist

Aeration in water slurries and controlled drying of manganous hydroxide produced from dithionate leaching of Artillery Peak manganese ores from Arizona were investigated by the Bureau of Mines at its Electrometallurgical Experiment Station, Boulder City, Nev., to determine whether a simple process could be developed for converting this product into a battery-grade manganese dioxide. The properties of manganese dioxide prepared by the thermal decomposition of manganous nitrate were investigated also. Manganese dioxide suitable for use in batteries was not obtained from the dithionate leach product, but some of the factors controlling its oxidation were isolated. Aging of manganous hydroxide was of major importance in retarding its oxidation by aeration. Sodium hydroxide and sodium silicate promoted oxidation by drying. Optimum quantities were about 0.85 mol of sodium hydroxide and 0.2 mol of sodium silicate per mol of manganese, and drying temperatures of 200° C. produced yields of manganese dioxide up to 90 percent of the manganese present. Higher temperatures and concentrations of reagents carried oxidation of manganese beyond its tetravalent state.

Jan 1, 1957

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952

By Robert W. Smith

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena. This report is the fourth of a series4/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the evaluation of the constant pressure flame temperatures of methane-air, propane-air, and ethylene-air mixtures for a range of pressures.

Jan 1, 1953

By Thomas M. Nasiatka

Tests with a high-pressure water jet were conducted in the steeply pitching Roslyn No. 5 bituminous coalbed in the Roslyn No. 9 mine, Roslyn, Wash., to determine the feasibility of extracting coal from pillars and from a solid coal face in development without drilling and blasting. During pillar mining, using a hand-held monitor, the best results were obtained with a 0.150-inch- diameter nozzle, a water pressure of 3,500 psi, and a flow rate of 38.5 gpm.3 The rate of mining and productivity were 0.74 ton per minute and 16.6 tons per man-shift, respectively. During development mining, using a monitor mounted on a roof jack, the best results were obtained with a 0.148-inch-diameter nozzle, a water pressure of 4,500 psi, and a flow rate of 40.0 gpm. In one section of the mine where the coal was relatively hard, the rate .of mining and productivity were 0.10 ton per minute and 5.7 tons per man-shift, respectively in another section of the mine where the coal was relatively soft, the rate of mining and productivity were 0.51 ton per minute and 8.3 tons per man-shift, respectively. The tests showed that hydraulic mining methods were more productive than conventional mining methods in pillar mining. In development the productivity of hydraulic mining depended primarily upon the coal hardness. Compared with conventional methods, hydraulic mining methods were less productive where the coal was relatively hard and equally as productive where the coal was relatively soft.

Jan 1, 1963

By A. L. Engel

This report is a compilation of results of brief preliminary tests on sulfide ores that contained gold and silver and, in some cases base metals. It is a companion paper to a recent similar report on oxide ores. Simple treatment methods employing the least possible equipment sometimes produce satisfactory results on marginal ores and in small-scale operations. Investigations of typical ores from newly discovered or recently explored mining districts have been made in continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno station, Bureau of Mines. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores as well as the conservation and recovery .of values in products that were discarded from former operations because of inability to treat them profitably. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas same involved samples of old dumps or tailings piles. The test work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials. The samples were representative of the districts from which they wore obtained, so this information should be helpful in the future development of these districts.

Jan 1, 1951

By F. B. Petermann

Two-stage electric smelting tests, using small submerged arc furnaces, were made on high-iron manganiferous materials from the Pioche District, Nev., and the Cuyuna Range, Minn. The object was to reduce sufficient iron in the first stage to give a slag with a favorable Mn to Fe ratio for smelting to ferromanganese in the second stage. The nodulized flotation concentrate from the Pioche District contained 29.2 percent Mn and had a Mn to Fe ratio of 2.3:l. When smelted with coke and silica or alumina as flux, more than 90 percent of the manganese was recovered in slags with Mn to Fe ratios of 10: :24:1. The Pioche slag was smelted to ferromanganese using coke and lime- stone or dolomite as flux. The ferromanganese was high in silicon but other- wise met specifications. Recovery of manganese to ferromanganese in this step was 73 to 78 percent. Overall recovery of manganese was about 70 percent. The sintered flotation concentrate from the Cuyuna Range material contained 12.9 percent Mn and had a Mn to Fe ratio of 0.3:1. When smelted with limestone as flux, about 83 percent of the manganese was recovered in a slag with a Mn to Fe ratio of about 6:1. The Cuyuna slag was smelted to ferromanganese with coke and limestone for flux. Recovery in this step was 61 percent of the manganese in a high silicon ferromanganese. Overall recovery of manganese was about 50 percent.

Jan 1, 1963