Search Documents

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

Objective The Roof Monitoring Safety System (RMSS) introduced in late 1997 has been modified to improve durability and simplify the measurement of roof or rib movement. Greater knowledge about the stability of roof and rib rock is expected to result in safer conditions for the mine worker. Developing safety tools and methods is part of NIOSH’s mission to prevent work-related injuries and deaths. A mining operation with a proactive approach to control ground conditions is in a better position to make essential decisions related to mine development and take remedial actions in the event of roof or rib falls. Background Falls of roof and rib rock are responsible for a high number of mining injuries and fatalities. Visual inspections and the sound of breaking or cracking rock are often relied upon to indicate unstable roof conditions. In some mines, roof bolt holes are checked for separations or gaps with a scratch tool; this provides further information about the stability of the roof. Monitors such as the RMSS can confirm roof movement that was surmised only by eye or ear, or potentially detect movement that was missed by these means. An added safety feature of the RMSS is the capability of locating the measurement station at a distance from where the monitor is placed in the roof. Stone and other industrial minerals are the basic raw materials used in construction. Continuing economic growth and highway building in particular have resulted in record demand for stone. This high demand, coupled with increasing constraints on surface mining, have caused many new .stone mines to be developed underground. These new mines in many cases will be employing new and inexperienced miners who may not have the ability to recognize unstable ground conditions using just sight and sound. From the initial introduction of the RMSS, it was anticipated that improvements and modifications would occur. We correctly assumed that, once miners and operators were exposed to the monitor. suggestions would evolve. In one case, the RMSS was used to determine if an impact hammer used on a mechanical scaler was causing or increasing instability of roof rock. The test showed little or no movement resulted from this method of scaling under the particular conditions at this mine. In another instance, an operator needed to monitor the stability of a haulageway in a benched area that had very high ceilings. The RMSS requires a 2-in-diam hole for installation; however, only roof bolt holes of a smaller diameter were available, and it was impossible to drill new holes at that height. The operator attached a 2-in collar at the roof line and was able to install the RMSS. These examples illustrate the potential for further enhancements of this tool. NIOSH continues to seek additional candidate sites for use of the RMSS. As usage increases, we anticipate further refinements and additional applications. How It Works The new RMSS, cable, and read-out box are shown in figure l. The read-out box has a green light that stays lit until battery replacement is needed. The red light is set to conic on to indicate movement. The red light can he adjusted for increments of movement as low as .010 inches. The RMSS red light should not be considered as a primary or only means of determining the stability of roof or rib. It is intended to serve as a supplement to existing methods or procedures for determining stability. An overview of the RMSS components is shown in figure 2. Movement of rock layers within the mine roof is measured relative to a fixed-point calibration at the monitor housing. The housing contains a potentiometer, roller switch, plastic rack, and spur gear. Movements are detected by the transfer of electromotive forces

Jun 1, 2000

By Ray J. Holmquist

"INTRODUCTION The Elk Mountain mica deposit was examined in June 1943 by the Bureau of Mines. An exploratory project and an access road for the property were recommended, provided the zinc was put in operation under competent management. K. Garard obtained a lease on the properly and started operations in June 1944; this was followed immediately by the Bureau's exploratory work. Road construction was begun by the Forest Service in July the same year.The lessee mined mica from the richest exposure with a crew of three men for 2-1/2 months. His operation terminated late in September, but the Bureau of Mines project and the Forest Service road construction continued until snow forced suspension of activity during the first week of November.The Bureau of Mines work consisted of trenching with a bulldozer, hand excavating on undeveloped outcrops, extending an existing adit, and starting a new adit below the older workings."

Jul 1, 1946

By H. W. St. Clair

In about 1930, Degussa applied for a patent on a process for the of oxides, carbides, sulfides, and other nonmetallic impurities by filtration in the molter state. The filtering media listed were wire screen, coke, and ceramic materials, and quartz. It was also suggested that filtration might be combined with chemical reaction between the metal and the filter medium or that might be added to the system. No patent was granted on the general scheme, but several years later a patent was granted on a continuous process purification of crude light metals, especially or alkali earth and their alloys. The melt was stirred at 1 temperature at which the impurities (such as oxides and salts) remained solid and the metal was drawn through a filter tube. The impurities collected under the filter and were removed by a screw conveyor. Crude sodium was purified by this process in Degussa's Knapsack plant. During the last war, when the refining of scrap became a very urgent Problem in Germany, experimental investigations were extended to separation of other metals and metallic compounds by filtration. Preliminary experiments seemed to confirm the opinion of Dr. L. Weiss that the principles of wet chemical filtration might be applied to a great extent in the purification of metal and alloys.

Jan 1, 1949

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By A. B. Cecala

A new prototype bag nozzle system has been designed under a Bureau of Mines contract to reduce dust generated during the bagging operation on fluidized air baggers. A field analysis of the new system has shown that the bag operator's dust exposure was reduced 83 pet. The amount of blowback was reduced 89 pet, which corresponds to a significant product savings. The new prototype system has been operating for a substantial period of time with no major problems.

Jan 1, 1984

By J. H. McClain

In the last 3 years' operation of the zirconium-production plant, zirconium metal has been employed to good advantage in many applications. The most frequent use has been in situations requiring resistance to attack by hydrochloric acid. In this service, it has been shown to be a serious competitor to Hastelloy. Zirconium also has excellent resistance to most other corrosives end could be considered for use as an all purpose metal. For example, this report cites 18 applications in hydrochloric acid, 4 applications in sulfuric acid, 5 applications in phthalic-hydrochloric acid, 3 applications in wet hydrogen chloride-chlorine atmospheres, and 2 applications in fused caustic.

Jan 1, 1954

By John Dixon

This paper is one of a series on milling methods and costs being published by the Bureau of Mines. Acknowledgment is made to J. B. Tyrrell, managing director, and Wm. Sixt, manager of the Kirkland Lake Gold Mines, for permission to publish this article. The Kirkland Lake Geld Mining Co.'s mill is located on Government Road at the west end of the productive part of the Kirkland Lake mining area, 1 mile west of the village of Kirkland Lake. The crushing plant is connected to the shaft house of No. 2 shaft, which is now the only operating shaft.

Jan 1, 1931

By J. F. Barkley

The following questions and answers were prepared principally to supply information in answer to general inquiries received by the Bureau from those contemplating the use of propane and butane fuels . Primary or basic information only is covered; this usually gives enough guidance for most inquirers . To those who wish information of the treatise type , the handbook , Butane- Propane Gases , published by the Jenkins Publications , Inc. , 1709 West 8th Street , Los Angeles 14, Calif . , is suggested .

May 1, 1949

By H. D. Baylor

This is the first of a series of papers describing mining methods and costs at cement plant quarries throughout the United States and deals directly with those methods employed and costs obtained at the quarry of the Louisville Cement Co. located at Speed, Ind. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Mr. J. M. Buohheit, superintendent of quarries, and Mr. H. E. Schoonover, quarry engineer, in furnishing data and in compiling this report.

Jan 1, 1930

By A. Z. Dimitroff

An improvised rock-dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By M. J. Ankeny

All bituminous-coal mines, by the nature of their product and inherent gassy tendencies, are subject to explosions or mine fires. The evolution from large, hand-loading sections employing numerous men and containing open-type equipment, lights, and nonpermissible explosives to small, concentrated mechanical sections with but few well-supervised men utilizing modern preventive equipment has not altered this premise. Mine catastrophes such as Centralia and New Orient No. 2, as well as recent disasters of less magnitude, have refuted the trend of thinking that modern equipment, will prevent or localize explosions and prevent widespread or loss of life.

Jan 1, 1952

By Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test-was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health or the Mine Safety and Health Administration.

Jan 1, 2006

By Robert L. Virta

The Bureau of Mines examined a fibrous talc sample from the Gouverneur talc district in New York by transmission electron microscopy (TEM) and polarized light microscopy to determine the mineralogical relationship of the fibrous talc to the amphiboles present in the sample. Two am-phiboles, anthophyllite and tremolite, were present in the sample. Tremolite occurred as a separate mineral phase, which was blocky in habit. Only a few composite tremolite-talc grains were observed. An-thophyllite, however, was present only in the fibrous talc grains. Mi-crodiffraction study of the fibrous talc grains containing anthophyllite showed that the anthophyllite was intermixed with the talc on a fine scale and that there was a crystallographic relationship between the talc and anthophyllite lattices in the fibrous talc grains. A mechanism similar to the process that forms biopyriboles could explain the structural defects, the fibrous habit of the talc, and the structural relationship between the talc and anthophyllite in the fibrous talc grains. Because of these characteristics, phase contrast microscopy and a provisional TEM technique for monitoring asbestos exposure would not distinguish between fibrous talc and fibrous amphiboles. TEM techniques employing electron diffraction and energy-dispersive X-ray analysis are recommended to positively identify the fibrous phases for regulatory purposes.

Jan 1, 1985

By Louis A. Panek

Roof bolting has been known for many years, although the practice had very limited application before 1948. Since then, bolting has been introduced as a systematic method of support in more than 700 coal mines and more than 200 noncoalmines and other underground openings in rock. By far the greatest number of bolts are used to support bedded roof. This is largely because of their use in coal mines, although roof bolts are used in mining bedded deposits of all kinds -potash (New Mexico), trona (Wyoming), and ores of iron (Alabama), lead (Missouri), uranium (Utah), lead-zinc (Utah), and copper (Michigan and Arizona). Thus, bolting has been successfully employed to reinforce bedded roof under a wide range of conditions despite the limited knowledge of the principles involved. This report develops the basic principles of bolting bedded roof based on elementary beam theory and on the results of tests intended to prove or disprove certain fundamental premises. Specifically, the objectives were to gain an understanding of the function of the bolts and the behavior of bolted roof and to establish standard bolt patterns. A combination of theoretical and experimental analysis was employed. The experimental method consisted of testing mine -roof models in a centrifuge. The models, the test procedure, and the model-prototype relations are described in a companion report (1)2/. A second companion report presents a method for designing systems of vertical bolts to reinforce bedded roof (2).

Jan 1, 1956

By Ernest E. Fairbanks

[Microscopic methods have proved to be valuable assets in the study of low-grade ores. While the chemical assay u a ally discloses tine total content of valuable metals in such an ore, a thorough knowledge of the nature of the ore should form the from which to prepare an efficient means of recovery. In the treatment of low-grade ores, inefficient recovery, as indicated bay the amount of valuable mineral permitted to go to waste in the tailings, is too frequently the rule rather than the exception, As methods of recovery become more efficient, many low-grade 10 mineral A posits suddenly assume o commercial significance, In much of this material the minerals are so finely disseminated and intermixed that identification even by microscopic methods is a difficult matter. The application of microchemical qualitative analysis with the aid of new device described in this paper, will solve many of the problems of identification encountered in the study of low-grade potential ores. In these ores, especially, the limitations of ordinary microscopic methods are liable to become very great. The microchemical tests obtained by applying a standard set of reagents to a polished knoting whether or not a tarnishing action develops, have considerable value but arc far from being infallible. It is well-known that electrolytic effects are apt to affect seriously the diagnostic value of the tests, end this effect is encountered much more frequently in dealing with finely desseminated minerals. resort to microchemical qualitative analysis, therefore, becomes indispensable.]

Jan 1, 1924

By H. A. Watson

Fluorine-containing polymers are comparatively new materials that exhibit very desirable characteristics not usually found in non-fluorine containing polymers. Among these characteristics are heat and flame resistance, desirable electrical properties, and chemical inertness. Polytetrafluoroethylene and polymonochlorotrifluoroethylene are examples of such polymers commercially available. In practical applications it is reasonable to expect thermal position of these materials if they are subject to high enough temperatures. The temperatures at which thermal decomposition takes place and the nature of the gaseous products of decomposition are considered pertinent data in intelligent use of these materials. The purpose of the tests discussed herein was to determine: (1) The temperatures at which gases were produced when small specimens of the two polymers were located and (2) determine the identity of the major constituents of gaseous products.

Jan 1, 1950

By Jerry E. Olson

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied additional areas, encompassing 11,303 acres, on the east and west sides of the 20,727-acre Badlands study area (Olson, 1987) in order to evaluate their identified mineral resources. The Badlands study area additions are located in Crook and Deschutes Counties, OR, about 10 and 18 miles east of Bend, OR. No mineral resources were identified. The additional areas studied are underlain by Tertiary-and Quaternary-age basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, mining claims or mineralized areas occur within or near the Badlands study area additions. Slab lava of marketable grade and quantity was not found in either area. None of the study area is of current interest for geothermal resources, but the eastern study area addition has been leased (1984) for oil and gas.

Jan 1, 1989

By S. A. N. Sheya

Many gold-bearing ores in the Western United States also contain small amounts of mercury. The presence of mercury creates potential pollution and health hazards during several steps in gold processing. An investigation was undertaken by the Bureau of Mines to develop techniques for removing mercury from cyanide mill solutions by selective electrowinning to reduce the potential hazards. Sixty-five percent of the mercury was selectively electrowon from synthetic carbon strip solution at applied potentials of 1.00 to 1.50 V when using a mercury-coated platinum or copper plate cathode. Increasing the active surface area by using mercury-coated copper wool resulted in up to % pct of the mercury being electrowon from mill carbon strip solutions that contained 1.9 to 20 ppm Hg, 20 to 345 ppm Au, and 0.35 to 39.5 ppm Ag. About 98 pct of the silver was electrowon with the mercury onto the mercury cathode. Gold extraction ranged between 0 and 20 pet. Results of the investigation showed that choice of cathode material was critical to the success of the process. Selectivity was not achieved using uncoated steel wool cathodes.

Jan 1, 1988

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.5 and 3 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year product Lon period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 Indexes. Initial capital investment is $33.8 million for the 1.5-MM-tpy mine and $61 million for the 3-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $52.5 and $94.2 million, respectively. These figures translate into total capital investments of $34.87 and $31.31 per ton of annual production. Assuming a desired 15-percent discounted cash flow rate of return, with Federal income taxes at 50 percent, the required selling prices would be $12.06 and $10.94 per ton for the 1.5- and 3-MM-tpy mines.

Jan 1, 1976