Search Documents

By D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, C. J. Malanga

There is evidence to suggest that cell injury induced in alveolar macrophages (AM) following phagocytic activation by silica particles may be mediated through changes in intracellular free calcium [Ca 2+}. However, the mechanism of silicainduced cytotoxicity relative to [Ca2+], overloading is not yet clear. To provide a better insight into this mechanism, isolated rat AMs were exposed to varying concentrations of crystalline silica (particle size< 5 µm in diameter) and the fluctuation in their [Ca2+]; and cell integrity were quantitatively monitored with the fluorescent calcium probe, Fura-2 AM, and the membrane integrity indicator, propidium iodide (Pl). Results from this study indicate that silica can rapidly increase [Ca2+]; in a dose-dependent manner with a characteristic transient calcium rise at low doses (<0.1 mg/ml) and an elevated and sustained rise at high doses (>0.1 mg/ml). Depletion of extracellular calcium [Ca 2+]0 markedly inhibited the [Ca2+]; rise (˜90%), suggesting that Ca2+ influx from extracellular source is a major mechanism for silica-induced [Ca2+]; rise. When used at low doses but sufficient to cause a transient [Ca2+]; rise, silica did not cause significant increase in cellular Pl uptake during the time of study, suggesting the presevation of membrane integrity of AMs under these conditions. At high doses of silica, however, a marked increase in Pl nuclear fluorescence was observed. Depletion of [Ca 2+] 0 greatly inhibited cellular Pl uptake, induced by 0. 1 mg/ml or higher doses of silica. This suggests that Ca 2 + influx, as a result of silica activation, is associated with cell injury. Indeed, our results further demonstrated that the low dose effect of silica on Ca 2+ influx is inhibited by the Ca2+ channel blocker nifedipine. At high doses of silica (>0.1 mg/ml), cell injury was not prevented by nifedipine or extracellular Ca2+ depletion, suggesting that other cytotoxic mechanisms, i.e., nonspecific membrane damage due to lipid peroxidation, are also responsible for the silica-induced cell injury. Silica had no significant effect on cellular ATP content during the time course of the study, indicating that the observed silicainduced (Ca2 ... ); rise was not due to the impairment of Ca2 + -ATPase pumps, which restricts Ca2+ efflux. Pretreatment of the cells with cytochalasin B to block phagocytosis failed to prevent the effect of silica on [Ca2+]; rise. Taken together, these results suggest that the elevation of [Ca2+]; caused by silica is due mainly to Ca2+ influx through plasma membrane Ca2+,channels and nonspecific membrane damage (at high doses). Neither ATP depletion nor Ca2+ leakage during phagocytosis was attributed to the silica-induced [Ca2+]; rise.

Nov 1, 1995

By T. R. Taubert, D. H. Carlson, J. H. Johnson

The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO, NO, and NO, at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory- grade instruments. Concentrations of CO and CO, measured by the EMA were usually within + 14 pct of concentrations measured by laboratory-grade instruments for CO and 220 pct for CO,. EMA- measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and CO, differences are related to the method of calculating the EMA&apos;s dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA&apos;s unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1992

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By Ted C. Briggs

A removable-jacket distortion apparatus was constructed and used to measure distortion coefficients for two high-pressure vessels. The measured distortion coefficients were used to compute distortion coefficients for volumes VI and (V1+V2) of a 1,000-atmosphere Burnett compressibility apparatus for the temperature range 0° to 75° C. Young?s modulus for Armco 17-4 PH stainless steel, heat treated to condition H1150-M, was computed from experimentally determined distortion coefficients. A 10-to 14-percent correction to the values obtained for Young&apos;s modulus may be required because pressure vessel end effects were neglected. The distortion coefficients of the compressibility apparatus are believed to be accurate to about 1 percent.

Jan 1, 1970

By C. E. Schmidt

Condensate waters from the Bureau of Mines Synthane process for coal gasification have been investigated by mass spectrometric methods to determine the organic contaminants. Waters from the gasification of six coals were extracted with methylene chloride, yielding 0.6 to 2.4 weight-percent extractable material. Using high-resolution mass spectrometry (HRMS), combined gas chromatography-mass spectrometry (GC-MS), and low-voltage mass spectrometry, 60 to 80 percent of the extract was found to be phenolic. About 20 organic contaminants have been identified and are present in the condensate waters from each coal gasified. The relative distribution of contaminants in the condensate water was nearly the same for the six coals gasified under various conditions; phenolic compounds were the most abundant in all cases.

Jan 1, 1974

By R. E. Peterson

The Bureau of Mines has undertaken beneficiation investigations on samples representing large tonnages of oxidized taconites in order to develop and evaluate applicable technologies for producing iron oxide concentrates from these materials. Information derived from the investigations can be used to expand the domestic iron raw-materials base and to establish the impact these taconite deposits may have on future national iron ore requirements. This report describes a process that includes reduction roasting, magnetic separation, and flotation, applied to a western Mesabi Range sample taken near Coleraine, Minn. The sample contained 36.8 pct iron and 46.0 pct silica, and represented 0.5 to 1 billion tons of crude material. An average of 962 lb/hr of oxidized taconite was roasted with 33 lb/hr of lignite in a 35-foot-long rotary kiln. Pulverized lignite and natural gas maintained the kiln operating temperature at 850° C. The roasted taconite was beneficiated by magnetic separation and cationic flotation in a 900-lb/hr pilot plant and yielded a product analyzing 68.1 pct iron and 4.6 pct silica, and containing 82.4 pct of the iron in the kiln feed.

Jan 1, 1981

Provide a means of evaluating the in place structural properties of coal seams and coal measure rocks in advance of mining. Approach Develop a sonic logging probe for use in dry wells, a condition common to shallow wells and semi-arid coal regions. How It Works The Bureaus&apos; sonic probe differs from conventional sonic probes because it does not require fluid in the well to couple sonic vibrations to the drill hole wall. A self-contained hydraulic system forces pistons containing the measurement transducers against the wall and clamps them in position until the sonic waveform information has been recorded. The pistons are then retracted and the probe is raised or lowered in the well as required. In the clamped position, the piezoceramic transmitter emits a sonic pulse which travels along the drill hole wall and is detected at the receivers in the form of compressional (P) and shear (S) wave motion. The receivers are designed to be sensitive to either the (P) wave or (S) wave motion as determined by the operator so that discrimination between the two wave types is improved by comparison of the respective output channels, and the travel time between transmitter and detectors can be accurately determined. Use of two receiver stations eliminates errors in timing of pulse travel because of electronic delays inherent in the probe.

Jan 1, 1981

By H. C. Miller

[California&apos;s sensational rise to supremacy as an oil-producing State in 1923 was accompanied by a loss of 62 lives. These 62 deaths were from oil-producing accidents alone and do not include fatalities at the refineries, on tankers, or on any work not directly connected with the drilling for and the production of oil. The number of facilities for 1923 was 82 per cent greater than in 1922, the next most fatal year, with a record of 34 lives lost. The data submitted in Table 1 show that for the calendar years 1917 to 1923 inclusive, an average of 4.74 million barrels of oil were produced per Vitality in the California oil fields. On this basis, the record for 1923, hough a trifle below the average, shove up slightly better than that for 1922.]

Jan 1, 1924

Provide the mining industry with a method for determining the gas content of ore bodies and associated strata for use in mine planning, Approach Samples of various rock types are collected and tested to determine gas content in conjunction with sample size, the collection method (i.e. whether the sample was collected from a core sample or by hand) mine gas emission, and the geologic location from which the sample was taken, such as near a fault, outburst area, or other geologic anomaly. How It Works Two methods were developed by the Bureau of Mines to determine the gas contents of rock samples. The first method developed involved dissolving minerals to measure gas emission. This method, however, can only be used with soluble minerals. A second method, therefore, was developed for use with insoluble minerals. With this method, the sample is crushed in a ball mill. Although the dissolution method is faster and more accurate to use, the crushing method is also advantageous because its use can more closely approximate a mining situation; the sample is crushed as in mining and the amount of gas released relates to the amount of gas that would be released during a mining operation. The dissolution method is applied to soluble minerals, such as rock, salt, or trona, in a sealed chamber. Gases released during dissolution are collected for analysis by gas chromatography. One advantage in using the dissolution method is that the test apparatus is relatively inexpensive. In addition, test can be performed at any scale, from single crystal samples to a solution mining operation.

Jan 1, 1983

By C. H. Elder, M. C. Irani

Two degasification test boreholes were drilled to depths of 1,238 and 1,212 feet on Bureau of Mines property at Bruceton, Pa., as part of the Bureau&apos;s long-range coal degasification program. The holes provided detailed geologic information and geologic sections, which were correlated with regional stratigraphic cross sections prepared by the Pennsylvania Geological Survey. Gas content determinations and coal analyses were made on the Upper Freeport, Middle Kittanning, Clarion, Brookville, and Mercer coalbeds; gas content of the coalbeds ranged from 53 to 165 cubic feet per ton. Formation pressure and gas flow tests were conducted on selected coalbed intervals in borehole 1; formation pressures ranged from 292 to 473 psig. The middle Kittanning coalbed was hydraulically stimulated using very heavy gelled water, but gas production remained low because gel residue and formation water inhibited the flow of gas. Gas contents in the Clarion, Upper Brookville, and Mercer coalbeds were anomalously low owing to the proximity of porous sand- stones which act as reservoirs for gas migrating from coalbeds.

Jan 1, 1977

By Jack C. White

The purpose of this Bureau of Mines work was to develop information useful in improving copper recovery during copper milling operations. Eleven copper mill tailings from the Western United States were subjected to froth flotation and cyanide leaching to provide an experimental basis for comparing their beneficiation response. Recoveries in flotation concentrates made from mill tailings ranged from 65 to 15 percent, at copper grades of 13 and 2.2 percent, respectively. Liberated copper sulfide minerals present in two samples were readily recovered by laboratory froth flotation. Nine of the samples were less amenable to froth flotation because of physical locking between copper sulfide minerals and gangue. Correlations among tailings indicated that recovery of sulfide copper by flotation was directly related to the sulfide copper content. Empirical equations derived from flotation data provided average values for unrecoverable copper and for recovery efficiency. Flotation response of copper mill tailings may be predicted from the equations. Data from cyanide leaching provides an equation describing the limiting high values for removal of copper by this method.

Jan 1, 1974

By Jeffery M. Listak, Ernest A. Curth

"It took only 9 years from the first appearance of roof shields on the U.S. longwall mining scene to the present predominance of shield faces. An apparent consequence is the welcome downward trend in accidents related to failures in longwall ground control. The report addresses load prediction, the effects of shield geometry on support loads, factors contributing to ground control, and related techniques. The Bureau of Mines took an active part in the evolution of longwall mining, including developing one of the first shield faces in 1975, the first lemniscatetype shields in 1976, the Mine Roof Simulator completed in 1980, the first shields in steeply pitching coalbeds in 1981, and the first multilift working of a thick coalbed in 1982. The information offered in this state-of-the-art report will assist in establishing criteria for roof support selection. INTRODUCTIONIn terms of roof support technology, the introduction of shields in the seventies and eighties was a major step forward. Table 1 indicates the predominance of shield faces on the U.S. longwall mining scene and its apparent consequence, a welcome downward trend of ground-control related accidents.The rapid progress of longwall technology began in 1975 and is highlighted by a development leading from the caliper shield to the modern lemniscate type. Shields have been gaining preference over chocks since their advent to longwall mining in 1975. Safety and productivity factors favoring shields over chocks are--1. A sheltered working space requiring minimum cleanup work.2. Structural stability that allows advancing without delay even with brushing roof contact and, by controlling all lateral loads, removing the requirement for cumbersome leg restraint and restoration devices.3. Wide hydraulic range of mining height.The development of roof shields in the Federal Republic of Germany preceded and paralleled their rapid adoption by U.S. miners. In 1983, 87 pct of the total production in Germany came from shield faces (1).2 In Great Britain, the National Coal Board introduced the first shield support system in 1977 to initiate Advanced Mining Technology (ATM) and Heavy Duty Mechanization (HDM) programs; as of mid-1982, 44 shield faces were operating, or 7.5 pct of a total of 581 faces CJ_)."

Jan 1, 1985

By J. Roger Loebenstein

ASARCO Incorporated, the only domestic arsenic producer, terminated copper-smelting operations and the associated recovery of byproduct arsenic trioxide at Tacoma, W A. in 1985. It still shipped small quantities of trioxide from its remaining stocks in 1987. Imports for consumption of arsenic trioxide were slightly higher than in 1986. Domestic Data Coverage.-Shipments of small amounts of arsenic trioxide from remaining stocks by Asarco were reported voluntarily to the Bureau of Mines.

Jan 1, 1989

By Ivette E. Torres

Many significant events that began in 1990-91 continued to have a profound impact in the world minerals economy in 1992. The dissolution of the U.S.S.R. and the formal breakup of the Council for Mutual Economic Assistance (CMEA) had significant effects far beyond the geographic boundaries of Europe and Central Eurasia. CMEA&apos;s network of economic interdependence had relied on central planning, a variety of subsidies, and barter agreements that allowed its members to function without the pressures of productivity and efficiency. In the mineral sector, many decisions had been made based on the need for military planning and technology competition with the market economy world. Because of inexpensive oil available through subsidies and technology assistance from the former U.S.S.R., industries III CMEA member countries had been able to function and maintain production to supply minerals and materials required to support the policies of the central plan. In 1992, most of the former CMEA countries decreased their output of many minerals. In some cases, the network of production that had been in place was severed. Political and economic instability, destruction of infrastructure, and new priorities were affecting other mineral industries in the area. In late 1991, 15 independent countries replaced the U.S.S.R. and in early 1991 the former CMEA countries found themselves trying to adjust to the realities of economic independence and the need to compete with former allies for survival. Although 11 of the 15 former Soviet republics joined in the Commonwealth of Independent States (CIS) in December 1991, in 1992, individual economic needs exceeded the needs of the Commonwealth III importance. As a result, new mineral trade patterns emerged as minerals were used as a source of much needed capital.

Jan 1, 1994

By Edward P. Barrett

[Iron oxides, when reduced at temperatures below 900° form a dark gray substance, very porous bait otherwise in almost the same form as the original particles. In the temperature ire range of 1,000 to 1,100° the product is pertly sintered but still shows the outlines of the original particles. Those products are known as "sponge iron." At temperatures of 1,100 to 1,2000 the metallic iron begins to flow together and to a semifused, pasty, porous mass called a "bloom," which can he worked under a hammer to form a product similar to wrought iron; it contains slag inclusions and is too low in carbon to make steel. If the temperature is 1,300 to 1,300°, part of the iron will fuse enough to absorb more carbon. The dissolved carbon lowers the melting point and still more carbon is absorbed. The melted portion acts a flux for the unmelted metallic particles until the entire mass becomes a high-carbon fluid known as "cast iron." Sponge iron was probably the form in which the first iron was recovered from the ores. As early as the eighth century the Catlan forge3 developed into a low-shaft furnace known as the "high bloomary," in which iron eras produced in the form of a pasty mass. In 1340 the first blast furnace was built in Belgium. The greater part of the iron was made into wrought-iron blooms by crude puddling processes. Charcoal was used as the fuel until tie latter part of the 17th century when coke was used in England. In 1865 Bessemer built his first converter in. England, and within a few years the Siemen&apos;s regenerative open-hearth furnace was developed, also in England. Enormous expansion in the metallurgy of iron followed. The idea of "direct processes" for the production of iron arid steel has persisted throughout all this time. The production of steel from sponge iron has theoretical advantages over the present-day standard methods, and handreds of so--called "direct processes" have been proposed or tried during the past century.4]

Jan 1, 1929

By Mark S. Sanders

The purpose of this work was to develop and field test improved knee protection for underground coal miners working in low seam mines. In a previous phase of this contract (Sanders, 1982), experimental knee pads were developed and field tested. The field test revealed several design deficiencies with the knee pads, and suggestions for improving the design were made. The work summarized in this report, therefore, consists of modifying the design and method of fabrication of the knee pads originally describes by Sanders (1982), and of field testing the improved design. The new prototype was shorter and wider than the original design, and used a neoprene pass-through strap design rather than a cloth strap molded into the pad itself. The new prototype was constructed by slush molding a hollow bladder that was then filled with foam. Initial reactions to the pads in the field test were very positive. However, after two months, the opinions about the new prototype became less positive. They were judged, generally, to be no better or worse than the pads usually worn by the field-test participants. Problems were encountered in the field with respect to durability. Water seeped into the inner cavity of many of the pads and caused the foam to deteriorate. It was concluded that it would not be cost-effective or feasible to significantly improve upon current commercially available knee pad designs.

Jan 1, 1986

By D. E. Hirsch

A systematic procedure for separation, characterization, and semiquantitative analysis of high-boiling petroleum distillates was developed by the Bureau of Mines and applied to a 370° to 535° C distillate of Wilmington, Calif., crude oil. Separation procedures employed were isothermal and molecular distillation, chemical treatment, silica-alumina adsorption, and gel permeation chromatography. Characterization and analysis were accomplished by gel permeation chromatography correlations and mass and nuclear magnetic resonance spectrometry. These data should be useful in improving petroleum processing and utilization and in achieving the energy conservation inherent therein.

Jan 1, 1974

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Exposure to excessive noise over time can cause permanent hearing loss. Workers in the mining industry are frequently exposed to A-weighted sound levels in excess of 90 dB. The A-weighted sound level at the roof bolter operator’s location can exceed 100 dB while drilling. The National Institute for Occupational Safety and Health (NIOSH) measured the sound pressure at the roof bolter operator’s position and utilized a phased array of microphones with beamforming software to identify noise sources on a roof bolting machine while drilling. The test data indicates the sound level at the operator’s position is dominated by the 2000 Hz through 5000 Hz one-third­octave-band sound levels. The beamforming results indicate that the drilling noise is primarily from two areas: the portion of the drill steel just below the rock and the drill steel-chuck interface. This paper will discuss the methods used to identify the primary noise sources.

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1982