Search Documents

The U.S. Environmental Protection Agency (EPA) and the U.S. Congress are presently considering several approaches aimed at reducing the amount of lead in the environment and society's exposure to lead. One approach is to tax domestic primary lead production or consumption. Objective To assist the Congress and the EPA in their decisionmaking, a study was initiated by the U.S. Bureau of Mines, which assesses the minerals related implications of a tax on U.S. primary lead production and primary lead imports. This investigation analyzes the impacts of a primary lead lax on: (1) domestic primary lead production, (2) domestic lead coproduct and byproduct production (including bismuth, cadmium, germanium, indium, silver, and zinc production), (3) domestic secondary lead production, (4) lead imports, (5) domestic lead recycling activity, and (6) the U.S. lead price. Study Findings Domestic Primary Lead and Primary Lead Coproduct and Byproduct Production. A quantitative analysis based on the application of the Bureau's Supply Availability System (SAM) has been conducted to determine the impacts on domestic primary lead and primary lead coproduct and byproduct production from domestic lead source material for a range of taxes.

Jan 1, 1992

Measure the leakage through individual crosscut stoppings quickly and economically so that the worst ones can be identified and repaired. (Typically 60 to 80% of the air supplied to a mine short circuits before reaching a working face.) Approach Most of the leakage through a permanent stop-ping is channeled through two windows in a temporary stopping, and air velocities through the windows are measured; leakage is determined from a formula. How It Works A temporary stopping made of plastic brattice is erected in the same cross cut as the permanent stopping, either upstream or downstream. The brattice is fastened to the roof, bottom, and ribs of the entry with spads. Normal leakage of brattice was allowed for in deriving formula, and does not effect results. For best accuracy the brattice and the stopping should be separated by a distance of one hydraulic diameter.

Jan 1, 1979

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator's position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

By David C. Oyler, Paul W. Jeran, William P. Diamond

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbecl at a vertical depth of 999 feet, The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a “bird foot” pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By R. A. Guidotti

The Federal Bureau of Mines has studied the reaction of oxides of columbium, vanadium, and tantalum with ammonia in vertical, gas-solids reactors at temperatures ranging from 300° to 1,300° C with the goal of preparing nitride intermediates for subsequent preparation of the metals by a thermal-decomposition step. The best nitride conversions were obtained in nonmetal reactors. With Cb205, V2O3, and V205 , low-temperature maxima in reaction rates occurred at 800°,800°, and 450° C, respectively, during oxynitride formation (in A1203) at 1 atm of pure ammonia. Conversion of the oxynitride, in a second step, to the mononitride was optimum at 1,200° C for columbium and 1,050° C for vanadium. In the case of Ta205, the rate of reaction to form Ta3N5 (in a single step) was highest at 900° C, where the presence of up to 5 percent methane was found to be beneficial; improved results were obtained by conducting the nitriding in a rotary kiln. Optimum space velocities (in the vertical Al203 reactor) ranged from 5,280 hr-1 for Cba205 to 7,950 hr-1 for V203. Oxide particle size had little effect upon reaction rates. Under fully optimized conditions, products containing less than 1 percent oxygen were readily obtained in under 6 hours.

Jan 1, 1975

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

It was determined that a selection of different types of fire sensors could be used to discriminate mine fires from nuisance emissions produced by diesel equipment. A neural network (NN) was developed for application to coal, wood, and conveyor belt fires in the presence of diesel emissions and evaluated with the successful prediction of twenty-two out of twenty-three mine fires based upon a fire probability determination. The optimum sensor selection for the NN was comprised of a carbon monoxide (CO) sensor, two different types of metal oxide semiconductor (MOS) sensors, and an optical path smoke sensor.

By J. E. Matta

The Bureau of Mines has developed a tracer gas method for measuring leak-age through permanent mine stoppings. In this method, a temporary brattice is erected in the same entry as the leaking permanent stopping. Leakage was evaluated from concentration measurements of a tracer gas introduced into the space between the stopping and brattice. Stopping leakages ranging from 15 cfm to 265 cfm were simulated in an underground coal mine. Leakage values determined by the new method were within 10 pct of the known values.

Jan 1, 1978

Develop a lightweight, portable device for use in mines for non-destructive testing of resin grouted roof bolt bond integrity. Approach A unique, intrinsically safe, electronic instrument has been developed that determines the holding quality of a fully grouted roof bolt by testing the integrity of the resin bond to both the bolt and to the surrounding rock. How It Works A measured pulse of energy Is sent Into the bolt by a piezoelectric transducer, and the instrument listens for reflected energy. Where the bolt is properly bonded, the energy passes from the bolt, through the resin, and out into the rock mass. Where proper bending does not exist, a portion of the energy Is reflected back along the bolt. The Instrument measures the reflected energy and compares it to the original pulse. The amount

Jan 1, 1982

By Daniel N. Tallman

To provide technology for achieving more efficient water filtration systems for the mineral industry, the Bureau of Mines performed demon-stration filtration tests at three iron ore mines and one steel mill. A comparison of equivalently sized magnesium oxide (MgO) and sand filters showed that MgO had a higher capacity and could operate at higher fil-tration rates than sand. In demonstration tests when alum (AlK(S04)2) was the coagulant, suspended solids breakthrough occurred even though the pressure across the filter (head loss) was 7 psig or less. Under these circumstances, the MgO demonstrated 20 to 100 pct greater filtra-tion capacity, defined in terms of the volume of water filtered before breakthrough. When an organic floccu1ant was used at one location, head loss was the run-limiting factor; the filters essentially plugged with-out any solids breakthrough.

Jan 1, 1985

Develop a method for mapping planar geologic features in deep underground mines where the presence of metal interferes with compass readings. Background A fundamental problem of mapping planar geologic features in deep underground mines is the presence of metal (water and air pipes, track, equipment, etc.), which affects the accuracy and consistency of compasses. Present geologic mapping methods include use of transits or theodolites, both of which are cumbersome and time consuming to use. To complicate the mapping, process each planar feature must be surveyed, and if that feature is not apparent on the opposite wall, it cannot be mapped. Another method of mapping is to stretch a tape measure between two survey spads and place a string along a planar feature on one wall and out into the opening until it intersects the tape measure. This method, in addition to being time consuming, is also inaccurate. Because detailed mapping of planar geologic features deep underground involves many repetitive measurements, a quick, accurate, and reliable method for making such measurements was necessary. The geolaser was developed to make such measurements in deep underground mines where metal interferes with conventionally used compasses.

Jan 1, 1990

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Utilize innovative processing technology to prepare high-purity, ultrafine advanced ceramic powders with little or no contamination occurring during the milling process. Advanced ceramic materials made from these powders could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. Approach Modify and evaluate the Bureau's turbomill, developed earlier to grind a variety of ceramic raw materials (clay, mica, and talc), as a milling or size-reduction technique for hard and abrasive advanced ceramic powders, such as silicon carbide. Background Powders for producing ceramic materials, such as silicon carbide. silicon nitride, alumina, and zirconia, which arc being considered for use in severe applications requiring high-temperature and/or corrosion resistance, are very difficult to reduce to fine sizes for processing into finished parts. Traditional techniques of particle size reduction, such as ball milling and jet milling, are very energy intensive and/or slow. These traditional techniques often produce materials that have a nonuniform particle size distribution and are contaminated by the milling media or container.

Jan 1, 1989

Reduce potential for steering errors during tramming of articulated vehicles, particularly when the operator is seated to the rear of the machine pivot point and is tramming in reverse. Approach Position-sensing and feedback cylinders were applied to the steering cylinders of two S&S cleanup tractors to cause the steering-control lever to match the orientation of the vehicle sections. The vehicles were tested in two working mines. How It Works A position-sensing cylinder (see Figure 1, Item A) is attached to one of the steering cylinders in the cleanup tractor steering system. As the steering cylinder piston rod is actuated by movement of the control lever, hydraulic oil flows from the position sensing cylinder to the feedbck-cylinder (B), causing the feedback-cylinder piston and rod to move. The outside end of the rod repositions the the steering-control lever until its angular position corresponds to the orientation of the vehicle sections.

Jan 1, 1978

By J. H. Maysilles

The Bureau of Mines is examining a variety of low-grade uranium ores because projections indicate that an appreciable percentage of future U.S. uranium production will be derived from resources containing 0.01 to 0.1 percent U308. One possible source is represented by a granitic material from Wyoming; the available samples contained 0.06 and 0.12 percent U308. Tests were conducted to explore the general leaching characteristics of this potential resource. The material responded to both acidic and alkaline leaching techniques. Conventional acid leaching extracted 93 percent of the uranium in 18 hours; the required acid addition was 50 to 100 pounds of H2S04 per ton of ore, and the oxidant addition was 3 pounds of NaCl03 per ton of ore. The acid consumption continues after maximum uranium recovery has been reached; this effect may complicate heap or in situ leaching with acidic solutions. Some variation in reagent requirements was noted between the two ore samples. Conventional carbonate leaching with strong solutions at 85° C extracted 94 percent of the uranium in 24 hours. These granitic materials also showed some response to dilute carbonate solutions, and the results suggest that the material may be chemically amenable to heap or in situ leaching with dilute carbonate solutions.

Jan 1, 1977

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

Develop an alternative to water bath exhaust conditioners (water scrubbers) for permissible diesel equipment used in gassy mines. Background Water scrubbers are a safety device used on diesel-powered vehicles in gassy mines. Exhaust from the engine passes through the scrubber, where it is cooled, and any flames or sparks present in the exhaust are extinguished. This prevents the ignition of combustible mine dust or methane that may be present. Unfortunately, water scrubbers consume large amounts of water and require frequent maintenance. Approach Methods that do not require water replenishment and frequent maintenance were investigated. The dry exhaust conditioning system was selected for investigation because no water is consumed and existing heat exchanger technology can be adapted to underground mine vehicles. In accordance with U.S. Mine Safety and Health Administration (MSHA) requirements, the system was designed to cool exhaust and trap flames and sparks. The U.S. Bureau of Mines (USBM) developed and evaluated a system for large engines and evaluated a second system for smaller engines. Both systems were evaluated on an engine test bed; if warranted, the system was then tested underground.

Jan 1, 1993

Design a new acoustic monitoring system to more accurately forecast impending rock bursts, and to assist in understanding the rock burst phenomenon. Background Rock bursts arc the major cause of injuries and deaths in deep underground mines in the Silver District near Wallace, ID. Bureau investigations of the rock burst phenomenon resulted in significant improvements in computerized acoustic technology, and achieved limited success in forecasting several large events. Research demonstrated that the location of rock noise, and the rate at which these events occur, are indicators of areas that could fail violently. In minewide monitoring, the typical array of acoustic sensors (geophones) is arranged to cover an entire mine with 16 to 32 separate instruments. The mines intended to be covered may be 7,000 feet in depth and up to several miles in extent. While such an arrangement is capable of detecting and locating large seismic events (rock slippage along natural fractures or faults), the geophones are too far apart to accurately locate mining-induced events at the active workplaces. The Bureau devised a strategy to concentrate the geophones into typical slopes (mining areas about 200 by 500 feet) to record the rock noise in areas where the miners work. By using such a dense geophone array at a mine, the Bureau provided event location and rate information to mine operators who removed workers and ceased production from active mine areas that subsequently suffered rock bursts.

Jan 1, 1989