Search Documents

By Maria I. De Rosa

This report analyzes mobile equipment fires for all U.S. surface and underground coal and metal/nonmetal mining categories by state and 2 year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from MSHA mine fire accident publications and verbal communications with mine personnel. The analyses will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the hazards associated with mobile equipment fires and will create a basis for future fire research programs.

Jan 1, 2004

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By R. Karl Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model, and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed that allows the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

Jan 5, 2007

By C. A. Komar

Hardness, tensile strength, and impact toughness of dry and brine-saturated sandstone specimens were measured at ambient, cryogenic, and elevated temperatures as a measure of the relative stability of reservoir rocks for subsurface disposal of liquid wastes. Hardness measurements were inconclusive. Tensile strength and impact toughness were significantly higher at -320° F than at ambient temperature, but were relatively unaffected at 700° F. Impact toughness was reduced by subjecting the specimens to three cycles of rapid temperature changes (thermal shock) over a 1,000° F range. Tensile strength of brine-saturated sandstone was less than that of dry sandstone. Based on results of the tests, reservoir sandstone likely would be stable if exposed to extreme temperatures of liquid wastes, although rapid changes in waste temperatures should be avoided.

Jan 1, 1971

"At the request of the Anthracite Institute, the United States Bureau of Mines during February, March, and April 1935, made a field survey of commercial anthracite shipped from collieries scattered throughout the Anthracite regions. In all, 268 samples were taken at 41 breakers from Carbondale at the northern end of the field to Pottsville at the south. These collieries ship approximately 50 percent of the industry’s total production. The geographical distribution of the breakers sampled was as nearly as practicable in proportion to the tonnage of the companies from each region cooperating in the plan.The following are the weighted average analyses, by sizes, of the samples taken in this survey;"

Jul 1, 1935

Provide minx operators with means for evaluating dust generation and bit wear effects on Production without costly and extensive underground testing. Approach Develop personal-computer-based cutting system models that will simultaneously evaluate machine, Coal seam, and mine-operator-controlled parameters for their interactive effects on dust generation, bit wear, and Production by either a longwall shearer or a continuous miner. How It Works CSM Programs have been developed to analyze relative dust generated by a double-drum, ranging arm, longwall shearer and a continuous miner. These interactive programs Provide relative dust, culling forces, and production values for any given set of mining machine parameters, specific seam conditions, and operator-controllable parameters. Expanded versions of each program provide a dynamic evaluation of the effects of bit wear, over time, on production.

Jan 1, 1989

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots."

Dec 1, 1942

By Ben A. Kornhauser

Petroleum production was the principal component of the mineral industry, followed by cement production and some salt output. The French Central Fund for Economics Cooperation loaned $9.15 million2 to the Communauté Electrique du Benin (CEB), which served Benin and Togo, toward financing the construction of a dam on the Mono River at Nangbeto, Togo. The dam was to supply hydroelectric power to reduce the energy dependence of the two countries and to irrigate crops. Nine other international financial organizations, including the International Bank for Reconstruction and Development (World Bank). the African Development Bank, the Arab Bank for African Economic Development, and the French Aid and Cooperation Fund, contributed to the estimated $140 million cost of the dam. The CEB also was to contribute to the financing. Contracts amounting to $60 million already had been awarded to West German and Canadian firms. The dam was expected to be completed in 1987.

Jan 1, 1986

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

By Sathit Tandanand

Geological differences among various coalfields restrain the applicability of subsidence prediction using empirical approaches previously developed. The Bureau of Mines assessed data collected from 16 longwall panels in the Northern Appalachian basin. Attention was focused on the effects of rock lithology, excavation width, and panel depth on the subsidence factor. The results show that the subsidence factor can be expressed in terms of the width-to-depth ratio by a simple exponential equation, which has a coefficient tentatively considered as the subsidence index. This index varies with the lithology of a particular site, and can be expressed in terms of percent distribution of weak and strong rocks in the overburden.

Jan 1, 1982

By John M. Gomes

Two methods for electrowinning tungsten from wolframite [(Fe,Mn)W04] were investigated. The first method, direct electrowinning from wolframite concentrate dissolved in molten salt mixtures composed essentially of various combinations of sodium phosphates, sodium borates, and sodium halides, yielded impure products. The second method was electrowinning from a halide-tungstate melt that was obtained from a high-temperature, two-phase extraction of tungstic oxide (W03) from wolframite. Electrolysis in electrolytes prepared from addition of sodium metaphosphate (NaPO3) and boric oxide (B2O3) to the halide-tungstate melt produced tungsten metal of 99.9 percent purity. Tungsten carbide (WC) was electrodeposited from the halide-tungstate melt when the melt was adjusted to contain 82 mole-percent NaCI and 6.0 mole-percent each of W03, sodium metaborate (Na2B204), and caustic soda (NaOH).

Jan 1, 1970

Provide sound battery safety guidelines for mine workers who maintain mobile surface mining equipment. Approach Battery-related accidents account for about 5 percent of all nonfatal disabling injuries in coal and metal nonmetal surface mines. These accidents occur despite the fact that appropriate battery safety technology (maintenance-free batteries, cable removers, fault detectors, hot-jumping systems, etc.) exists. Mine operators are not always aware of the safety measures that could be taken because this safety information is widely scattered in numerous unrelated technical reports, vendor brochures, and journal articles. A literature search of these reports and a review of relevant industry standards, handbooks, and references on battery safety, followed by discussions with mining company and MSHA personnel, provided the Bureau of Mines with the background necessary to develop procedures for proper and safe battery usage. These procedures were condensed and written in nontechnical language to serve as guidelines in assuring battery safety during maintenance of mining equipment.

Jan 1, 1986

By Foster Fraas

In this Bureau of Mines report, use of the photoemission of electrons to produce electric charges for the electrostatic separation of sonic dispersed minerals, which had previously been ground to pass a 43µ-opening sieve, is demonstrated. It appears that many of the oxides, carbonates, sulfides, and arsenides will respond to photoemission. Minerals least responsive are the oxides of silicon, the oxides of aluminum, and minerals that have a high concentration of these oxides. Although several synthetic ore mixtures did not yield to complete separation in a one-stage operation, it is probable that preliminary neutralization of the initial electric charges produced by powder dispersion will provide complete separation. That the separation can be carried out in air and without the use of reagents or heating, which are required in the present practice of electrostatically separating coarse granular feeds, is of special significance.

Jan 1, 1972

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By L. H. Banning

The Bureau of Mines conducted pioneering batch and laboratory cyclic tests that simulated plant operation in developing a procedure for acidulating phosphate rock with fluosilicic acid. Both high-grade deslimed phosphate rock and low-grade phosphate rock samples were treated. The most promising results were obtained by acidulating des limed high-grade material. In a series of seven cyclic tests, 85.4 percent of the P20S was recovered in solutions. The average P2O5 content of the phosphoric acid-monocalcium phosphate solutions of the first step was 156 grams per liter, and the average fluorine content was 4.7 grams per liter. Residues had an average fluorine content of 30.7 percent and contained 83.9 percent of the total fluorine in the charge materials. Some fluorine was lost by volatilization.

Jan 1, 1975

By Murali M. Gadde, John A. Rusnak

Rock mass classification systems are extremely useful for site characterization and have been employed by the rock mechanics community for several decades. While empirical in nature, the classification systems provide a viable means to quantify the nature of rock mass, which is necessary for stability analyses. In U.S. coal mines, the Coal Mine Roof Rating (CMRR) is the most widely used classification system for several purposes, including sup-port selection, chain pillar design, assessing the stability of extended face cuts, etc. The Analysis of Roof Bolt Systems (ARBS) is an empirical method developed from the CMRR to guide selection of roof bolts as the primary support system in U.S. coal mines. In this paper, the experience of Peabody Energy in applying ARBS to sup-port design is discussed. In general, data from the Peabody mines show that ARBS predictions match well with field conditions. Peabody, however, does not use ARBS as the stand-alone methodology for support selection. Peabody uses a two-pronged approach in which the support requirement is initially estimated from the classification method, and then numerical modeling is used to select the proper reinforcement system. Such an integrated approach is necessary, as ARBS suggests only the “amount of steel” that may be used to support the roof and does not specify which type of roof bolt to use. A case study is used to demonstrate the usefulness of ARBS and Peabody’s integrated approach to support design. Also, the application of ARBS at several Peabody mines showed a very good correlation with support cost. The correlation indicated a direct relation between bolting cost and the ARBS value.

Jan 5, 2007

Lower the respirable dust exposure of longwall shearer operators by keeping the dust cloud confined to the face. Approach Change the location of face-side machine cooling, water sprays. How It Works The dust breathed by the longwall shearer operator is usually produced by the shearer itself. The dust cloud originates at the face, and the exposure of the operator depends largely on how quickly this cloud spreads into the walkway. Water sprays on the shearer body can have a large effect on dust cloud spreading. Results to date indicate that sprays can help confine the dust cloud to the face if they are carefully placed. Otherwise they can make dust levels far worse. The worst offenders are often face-side sprays used to discharge cooling water from the cooling jackets of the shearer motors. These face-side sprays set up an air circulation pattern as illustrated in the drawing. Air induced by the sprays to flow towards the face, raises the air pressure in front of the face, which causes the air flow to turn and then move back over the shearer, bringing dust with it into the walkway.

Jan 1, 1981

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984

By Connie S. Musulin

The Bureau of Mines conducted an experiment at Exxon Mineral Co.'s Buffalo Shaft Operation to determine the time required for radon concentrations to return to a base average after fan shutdowns. Shutdown times ranging from 5 min to 16 hr were evaluated. An equation was derived to calculate a ratio that determines the time required for the radon concentration to return to the average level that existed in the mine prior to shutdown. For fan shutdowns of 15 min or more, underground personnel should be evacuated to areas with natural downcast ventilation. For shutdowns of less than 1 hr, personnel should not return to the working area until the elapsed time is four times the shutdown, or until the working area is resampled and found safe. If the mine is not in production during weekends, the downcast fans can be turned off .from midnight Friday until 4 p.m. Sunday, and the radon daughter concentration should be below 1 WL throughout the mine by the start of the shift Monday. This fan shutdown would conserve energy and save the mining company an estimated $21,000 each year.

Jan 1, 1982