Search Documents

By A. G. Kim

Coal formation begins in peat swamps or bogs, in which microorganisms alter plant material and initiate the formation of carbonaceous sediments. Methane, which constitutes about 98 percent of the hydrocarbon gas in coalbeds, is known to be a product of anaerobic microbial metabolism. To determine if other hydrocarbon gases could be produced in an environment similar to that of a swamp, samples of wood cellulose and lignin were inoculated with soil micro-organisms and incubated anaerobically. The resultant gases included methane, ethylene, propane, propylene, butanes, pentanes, and carbon dioxide. Hydrogen was also produced from the wood samples during the first month of incubation. Over 90 percent of the produced gas was methane; C02 was the other predominant component. Concentrations of all other hydrocarbon gases ranged from l to 20 parts per million, approximately 0.1 percent of the total hydrocarbons, which was less than the concentration in coalbeds. Therefore, although higher hydrocarbons could be produced in a swamp environment, subsequent mechanisms, either concentration by adsorption or formation during geochemical reactions, must affect the final concentration of higher hydrocarbons in coalbeds.

Jan 1, 1972

By Ryan G. Wade, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

By Philip A. Holland

The Bureau of Mines has developed a method for determining helium in water for use in sampling and analyzing surface and subsurface waters for geochemical survey work. The accuracy of the analytical method is within ±10 percent for samples containing above 20 x 10-8 cm3 He (STP)/cm3 H20. The minimum detectable helium-in-water concentration is calculated to be 2 x 10-8 cm3 He (STP)/cm3 water. Water samples are collected in 500-cm3 stainless steel cylinders. The dissolved gases are extracted into a cylinder of equal volume containing a known quantity of neon. The resulting gas mixture is subsequently analyzed for helium and neon-21 by mass spectrometry. The volume of helium in the sample is calculated from the mass spectrometric determination of the helium-to-neon-21 ratio, the known quantity of neon used, and the extraction efficiency of helium.

Jan 1, 1981

By H. B. Freeman, E. J. Gleim

During the 12 months ended July 1, 1931, engineers of the Bureau of Mines examined electrical equipment in 80 bituminous-coal mines. The purpose of these examinations was to ascertain the condition of such equipment with respect to possible hazards of gas and dust ignitions, also of shock. Although only 3 of the 80 were being worked with open lights and therefore did not use explosion-proof equipment, there were others where electric cap lamps were used by the men but where it was apparently assumed that conditions as to gas and dust did not require equipment designed to give protection against ignitions. Early in its history the United States Bureau of Mines originated certain standards covering the construction and testing of electrical equipment in order to minimize the dangers of ignitions from exposed electric sparks and flashes ; accordingly, it is comparatively easy to determine wherein a machine built to these standards falls short of continuing to meet them if damaged or neglected. Many so-called flame-proof and dust-proof machines, however, have not been built to any standard comparable with that developed by the Bureau of Mines. In addition, certain machines have parts which pass Bureau of Mines tests, but do not satisfy the full requirements in other respects, and others make no pretense of inclosing the spark-producing parts. It is not uncommon to find two or more of these various types in the same mine with " permissible " machines, the type that has been built to conform to the Bureau of Mines standard. Consequently, inspection of nonpermissible machines becomes somewhat difficult without a standard of comparison. Because of its unprotected condition obviously open-type electrical equipment must be used with great care, if at all, in a mine where precautionary measures are adopted in guarding against gas and dust ignition. The unsafe nature of such equipment is widely recognized. For that reason it is to be installed only where there is no likelihood of gas being present. It is not apparent to some, however, why flame-proof and dust-proof equipment and equipment having tested parts should not be regarded in the same light as permissible equipment.

Jan 1, 1932

By V. A. Marple, K. L. Rubow

"IntroductionA particle dispersion system has been developed to aerosolize bulk powders or material deposited on surfaces such as filters. The size distribution of the aerosolized particles can then be obtained by sampling the particles with an aerosol sizing instrument such as a TSI aerodynamic particle sizer (APS) or a cascade impactor.Of particular interest is the applicability of using this technique to obtain the size distribution of particles collected on filters. This system has been used to determine the size distribution of coal dust particle collected on membrane filters. The use of this device in this application is quite intriguing in that, if this technique can be shown to accurately determine the size distribution of airborne particles, one can easily collect particle samples using either personal or area particle samplers, determine the mass concentration of the collected material through gravimetric techniques and then use the particle dispersion system coupled with the APS to determine the particle size distribution. With this technique one can determine the particle size of dust in environments, such as underground mines, where it would be inconvenient or impossible to use a particle sizing instrument.Particle Dispersion SystemA prototype particle dispersion system has been developed for aerosolizing particles. A schematic diagram of the system is shown in Figure 1. The system consists of mechanism for advancing the particle sample beneath a dust pickup tube, a venturi for deagglomerating the particles, and a instrument for analyzing the aerosolized particulate matter.The procedure to analyze a particle sample is as follows. The particles to be aerosolized are placed on a sample plate from where the particles are picked up by an air stream flowing upward in a small capillary tube (dust pickup tube). This tube operates as a small vacuum cleaner passing over the sample plate. The air is drawn up the capillary tube at a rate of 2 L/m by a venturi aspirator. This is accomplished by placing the outlet of the capillary tube near the throat of the venturi. The accelerated velocity of the air creates a low pressure in this region which draws flow up the capillary tube. From the outlet of the capillary tube particles are transported to the inlet of the APS where a small fraction are sampled and the aerodynamic diameter of the particles determined. The particles which are not measured by the APS are passed into a HEPA filter."

Mar 1, 1989

By Wilson Blake

The Bureau of Mines used a mathematical model based on the finite element method of stress analysis to calculate stresses and displacements surrounding an open pit mine in a gravity-loaded rock mass. Comparison of the finite element solution for a semicircular notch in a gravity-loaded plate with the theoretical solution for a semicircular notch in a plate under uniform compression parallel to the free boundary demonstrates the inapplicability of the latter method to openings at the free surface of a gravity-loaded medium. High stress concentrations are formed at irregularities along the boundary of an open pit in a gravity-loaded continuous competent rock; however, for this type of rock the magnitudes of the stresses are too low to be considered a major factor in open pit slope stability. High stress magnitudes will occur if, in addition to the gravity stress field, a large horizontal stress field exists.

Jan 1, 1967

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

By E. D. Gardner

An explosion occurred in a high-pressure compressed-air line in October, 1930, at an Arizona copper mine. The explosion was unusual, and nothing had teor. noted by the plant operators to indicate the possibility of such an occurrence. It is necessar The air is The mining company uses compressed-air locomotives to haul about 4,500 tons of ore per day from the stopos to the pockets at two hoisting shafts. The ore cars hold five tons each, and are pulled in trains of 30 cars. to charge the locomotive with compressed air at both ends of the trip. conveyed from the compressors at the surface to the distributing points unier roun in special high-pressure four inch steel pipe that was tested to withstand 2500 pounds per square inch before being installed. The air is delivered to the loco- motives at a pressure of 1000 pounds per square inch. There are no receivers in the system. The air for running the locomotives is compressed by one three-stage and two four-stage compressors which have capacities of 600 and 300 cubic feet per minute, respectively. These machines are operated by electric power, and are in an end of the main compressor building in which air is compressed to supply the air drills in the mine. Whenever the demand decreases, as at the noon hour, one or more of the Compressors are shut down. On this particular occasion, at the end of the noon hour, one of the operators was approaching the high-pressure compressors to start the two smaller machines that were not running, when the explosion took place under the floor a few fost ahead of him. The man was mocked down and received some superficial cuts and bruises, but was not seriously injured. The floor was torn , the side of the building blown out, and holes imo cited in the roof some twenty feet above. The explosion was immediately followed by a fire which was quickly put out by the plant operators with hand fire extinguishers. At the time of the explosion the 600 cubic foot compressor was running alone, and the pressure in the system at the machine registered 1040 pounds por square inch. On examination it was found that two 6-fout sections of pipe, about tan feet apart, were completely ruptured into twisted fragments; the rest of the pipe line, apparently, was not injured. The destroyed sections were in that part of the pipe near the large compressor and above the connection from the two smaller machines. It is not definitely mom what caused the explosion. Explosions in other compressed-air systems have taken place, and, although of rare occurrence, have caused loss of life. Such explosions are not confined to high-pressure installations and several have occurred at plants compressing air te one hundred pounds per square inch, or less. plosions of this nature are not to be confused with the rupturing of compressor cylinders from excessive air pressure caused by the discharge valve being closed.

Feb 1, 1921

By A. B. Hooker, L. C. IlsLey

The greatest hazard of early mining was from explosions of methane ignited by open lights . With the advent of safety lamps and forced ventilation this hazard was greatly reduced until the application of electricity to modern mining not only multiplied the sources of gas ignition but the accompanying , machines and haulage systems increased the amount of explosive dust , through which a methane explosion is more liable to become a major mine disaster , and thus greatly furthered the need of adequate ventilation to keep down the concentrations of methane . Adequate ventilation is still the best preventive of such explosions . However , even with a well laid out and controlled ventilating system the amount of air passing through entries and rooms is liable to vary within wide limits because of open doors , falls of rock , or other accidental causes . The percentages of methane under normal conditions should therefore be kept so small that they will not be increased to explosive proportions by short interruptions in ventilation . Mine ventilation and methane detection are inseparable safety precautions . The increasing importance of ventilation necessitates more accurato determinations of the methane concentrations throughout the mines . This paper discusses in detail some of the steps in the development of methane detection and specially notes the more accurate detectors now available . One of the earliest means of detecting methane was by a candle . About 1835 , John Buddle , Sr. , a noted mining man of his period , when questioned by a Parliamentary Committee as to the safety of using candles , replied :

Jun 1, 1933

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

By W. C. Phalen

"The Phosphate Rock Market:Indications, in the fertilizer market, point to a prosperous condition, caused chiefly by the growing demand for all classes of fertilizer material in spite of a shortage of supplies. Both of these conditions have been caused by the war. The shortage in phosphate rock is being relieved as production increases, but the supply has not caught up with the demand for this spring's trade, at least. Reports from Florida are to the effect that more than half the necessary quota of laborers are at work. This may not appear to be a very good showing, but even this situation is en¬couraging because there is a larger force now at work than has been the case for some time, and it is steadily, though slowly, increasing. Some of the producing companies are conducting advertising campaigns to get laborers back to the phosphate fields and attractions in the way of better housing and living conditions are being offered.Producers are far more confident about the situation than they were two months ago, and though the shortage will not be met before the end of 1920, theme is a surplus accumulating over what is going out on existing contracts.Quotations are now being offered on all Florida rock excepting land pebble and this, it is expected, will be soon quoted.Quotations on Florida rock per ton are as follows:"

Jan 1, 1920

By S. P. Howell

The Bureau of lines as repeatedly called attention to dangerous practices in the transportation and opening of kogs of black blasting powder. In 1914 Diwin Higgins (Prevention of Accidents from Explosives in Metal inos, Miners' Circular 19, Bureau of Mines, p. 15) stated "canisters should always be opened by removing the bung. To use a pick or other sharp tool for cutting a hole in the canister is dangerous. After the necessary amount of powder has boon taken out, the canister should be kept closed. The powdor should always be handled at a safe distance from an open light." In 1919, Geo. S. Rice (onthly Statement of Coal line Fatalities for June, 1919, Bureau of Mines, pp. 16 to 18) calls attention to the dangers that arise in underground transportation and handling of explosives, and calls special attmtion to the danger of hauling explosives in motor trips; the unnecessary risk involved in hauling men on the trip at the same time, and the necessity of keeping open lights away from black blasting powder. In 1919 the writer (Sensitiveness of Explosives to Frictional Impact, Tech. Paper 234, Bureau of Mines, pp. 13, 15) called attention to the fact that black blasting powder is not as sensitive to frictional impact as the nitro-glycerin dynamites and the gelatin dynamites. Black powder may be ignited by direct impact and the writer believes that this may occur without presupposing a preliminary spark. It is well known, however, that black blasting powder is very sensitive to ignition by spark flame, or heated materials, and these may be produced by an electric current, by an open light, by incandescent particles from a pipe, cigar, or cigarette, by the tearing of metal sheets or scraping of metal against metal, and possibly, by other means. -- The above discussion will serve to introduce a newly recognized hazard the ignition of black blasting powder by the forcible opening of kegs with wodden tools. The details of three accidents in which kegs of black blasting powder ex- ploded instantly when a wooden tool was driven forcibly through the top of the kegs are as follows: 1. In 1915, a powder man employed by a coal mining company stated that he was opening a 25-pound log of black blasting powder by driving a hole in the top with a wooden sprag when the powder in the leg ho was opening ignitod. This caused the ignition of fifty-two additional 25-pound logs of the powder, and the fatal burning of this and another powder man. The ono making this statement lived five hours after the explosion.

Sep 1, 1920

By Arthur E. Goddard

Radio propagation measurements were conducted in a coal mine at UHF (200 to 1000 MHz) and VLF (1 to 50 kHz) to characterize the transmission loss of intra-mine paths. The basic experimental parameters included frequency, polarization, path orientation and distance. Further tests evaluated the performance of roof-bolt vs. loop antennas at VLF and parasitic reflectors at UHF. Measurement results are summarized in a series of transmission loss curves. Examples are presented to show the use of these curves in predicting the performance of radio communication systems in mines.

Jan 1, 1973

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

To increase awareness of float coal dust explosion hazards in the mining industry.

Jan 4, 2006

To inexpensively monitor the ventilating airflow anywhere in underground working places. The Approach: The Bureau has developed a small self-contained monitor which sounds an audible alarm and energizes a flashing lamp if air velocity decreases below normal. How It Works: The sensing element of this inexpensive monitor is a thermistor, which is self-heated by a constant-current electrical source. Airflow over the thermistor increases heat removal and lowers the thermistor temperature. Since the electrical resistance of a thermistor is a function of temperature change, the voltage across it varies with temperature, and, therefore, the air velocity. Changes in the voltage across the thermistor are amplified, and can be used to trigger the alarms.

Jan 1, 1975

By Fred N. Kissell, R. J. Bielicki

In this report the importance of diffusion in controlling the emission of methane in mines is examined. An in-situ diffusion parameter is defined and calculated for a hypothetical unfractured lump of coal in the Pittsburgh and Pocahontas No. 3 coalbeds. The values obtained are similar to those obtained with lump coal in laboratory experiments.

Jan 1, 1972

By L. B. Pankratz

Enthalpies above 298° K were investigated for four crystalline sodium borates by copper-block drop calorimetry. Determinations were made to 1,200° K for NaB02, 1,003° K for Na2B407, 1,005° K for NaB305, and 1,046° K for Na2Be013. No phase transitions or other thermal anomalies were found. The enthalpy determinations, when combined with known heats of formation at 298° K and other supplementary data, enabled the calculation of the heats and free energies of formation of the compounds to their melting points. Values of relative enthalpies, entropies, heat capacities, free energy functions, enthalpies of formation, free energies of formation, and equilibrium constants of formation were tabulated at even temperatures.

Jan 1, 1971

Develop a cost-effective, flexible method for extinguishing underground coal mine Fires that can be readily used in fire conditions encountered in both abandoned mines and coal outcrops. In addition to the abatement of an underground coal fire, a secondary objective was to prevent subsidence by filling the voids with a material having sufficient compressive strength to minimize subsidence. Approach The Colorado School of Mines Research Institute was awarded a research contract to determine the viability of using Foaming Mud Cement for abating underground coal mine fires and preventing subsidence. The program consisted of a laboratory and pilot scale investigation and process development. An extensive, controlled test program was conducted simulating floor, rib, roof and rubble fire conditions. Field demonstrations were conducted after the pilot scale research was completed. How It Works Traditional techniques have targeted the control of burning by eliminating the air, fuel source or heat. This has been accomplished by trenching, quenching, mothering or combinations of these three methods. These techniques were not always successful, particularly in the case of fires in abandoned mines.

Jan 1, 1991

By Charles L. Kimbell

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom has been continued this year in tables 23 and 24. As a result of the lack of availability of comprehensive data on the prices of metals in Canada, the table that had presented that information in past years in this chapter has been discontinued and the price series for nickel that had been in that table now appears in the table presenting metal prices in the United States.

Jan 1, 1993