Search Documents

By Robert J. Timko, R. Lincoln Derick

This U.S. Bureau of Mines study examined spontaneous heating episodes in coal mine pillars in an active underground coal mine. The information obtained from these incidents was then analyzed to learn which sampling methods provided the earliest indication of pillar heating. The objective of this study was to discover if the location of future events of pillar spontaneous heating could be inferred from the available information. The spontaneous heating-prone area in this evaluation involved pillars located just in by the mine portals. Several detection methods were used to determine gas levels outside as well as inside the affected pillars. It was hoped that, by incorporating external and internal sampling methods into an organized program, locations undergoing spontaneous heating could be determined more readily. This study found that by drilling small-diameter boreholes into the pillars, then obtaining gas samples from the affected pillars, the ability to locate early spontaneous heating episodes was improved. However, the ability to accurately predict future spontaneous heating events remains in question.

Jan 1, 1995

Montana's coal reserves are estimated to be more than 120 billion tons, 24.6 percent of U.S. reserves. Montana's reserves are the largest in the nation. Coal fields are located throughout the state, primarily east of the Continental Divide. Three of the state's 17 coal fields have producing mines. Coal resources range from lignite to high volatile bituminous; however, most of the coal currently mined is subbituminous. Although Lewis and Clark mentioned the presence of coal along the banks of the Missouri River in Montana in 1805, the first major mine was not opened until 1867, at Chestnut, Montana, near Bozeman. The mine at Chestnut served Fort Ellis until the mine was bought by the Northern Pacific Railroad in 1883. By 1900, underground coal mining had developed throughout the state, primarily to supply fuel to the railroads. In the 1920s, large-scale surface mining began in Colstrip to fuel railroad steam engines. Currently, all coal mined in the state is produced from surface mines. The Office of Surface Mining granted the Montana regulatory program conditional approval April 1, 1980, followed by final approval February 1 1,1982. Montana's Abandoned Mine Lands Program was approved November24,1980, and its emergency program was approved August 18, 1983. A Federal Lands Cooperative Agreement was approved May 8, 1981.

Jan 1, 1992

By J. W. Horne

The quantitative determination of salt in petroleum ins generally divided into two steps - (1) extraction of salt from the oil and (2) accurate measurement of the extracted salt. This paper presents a method used by the Bureau of Mines for quantitatively extracting the water-soluble chloride salts4/ from petroleum and discusses important details attendant on the success of the method. Among these details are homogeneity in the dispersion of salt crystals, emulsified brine and other impurities in the oil sample, complete solution of the salt, and total extraction and titration of all the aqueous phase. Recently, the chlorides of sodium, calcium, and. magnesium produced with and present in various oils have developed growing problems of salt deposition and corrosion in the petroleum industry. Therefore, a technical study of various emulsions and salts that accompany petroleum is being made by the Bureau of Mines in cooperation with the State of Oklahoma. One report (5)5 reviewing the literature pertinent to the study has been published.

Jan 1, 1940

By Isaac A. Zlochower, Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coats, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane-air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.

By Liming Yuan, Charles D. Litton

This paper presents experimental results for conveyor belt flame spread from tests conducted in a small-scale tunnel. The purpose of this study is to investigate the effects of belt type, ventilation velocity, belt surface-to-roof distance and ignition source power on the flame spread properties. The tunnel used was 4.9 m long by 0.46 m square with the ventilation velocity ranging from 0.7 to 3.2 m/s. The ignition source was an impinged methane jet burner with heat output ranging from 7 to 21 kW. The belts tested included non-fire resistant rubber belts, fire-resistant rubber belts, fire-resistant neoprene belt and fire-resistant PVC belt with belt samples measuring 0.23 m wide by 2.5 m long. Experimental results show that with a ventilation velocity of 1.02 m/s all conveyor belts could be ignited, and that with sufficient ignition source power, flames spread the full length of the belt sample. The data showed a coupling effect of the ventilation air velocity and the belt surface-to-roof distance on the flame spread rate. For instance, flames could not spread with a ventilation velocity higher than 1.52 m/s and a surface-to-roof distance of 0.22 m. The use of the measured CO/CO2 ratio as an indicator of combustion stoichiometry is also discussed.

By R. Karl Zipf

Use of Salamon's stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon's stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

Improve the safety of roof bolting machine operators working in underground coal mines while maintaining or improving efficiency of the roof bolting operation. Approach The Bureau of Mines funded research under contact to develop equipment that would assure greater safety in drilling holes and installing roof bolts. The research led to the design and fabrication of a roof-boiling machine that allows its operator to per-form drilling and bolting tasks while under permanently sup-ported roof or canopy protection. How the Prototype Works The major components of the remote-control roof bolter are a flexible-shaft drill that provides continuous drilling capability without the need to Stop to add drill extensions for long holes; a roof-bolt inserter that can bend a longer-than-seam height roof bolt into the drilled hole; and a roof-bolt lifter/torquer that completes insertion of the roof bolt into the hole and torques it to the desired tension.

Jan 1, 1986

By Gary L. Mowrey, William D. Monaghan, George F. Persetic, Gregory M. Molinda

Ground penetrating radar (GPR) has been investigated by the U.S. Bureau of Mines Pittsburgh Research Center for its potential to determine rod hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth to determine the value of GPR for roof hazard detection. The resolution of the current systems allows detection of gross roof fractures (>6A mm (>0.25 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologics changes in the roof. Differences in data quality are discussed, as well as suggestion for collecting improved data.

Jan 1, 1996

By Doug Tesarik

The study of neutrinos?particles infinitesimally smaller than atoms?would be significantly advanced if a deep underground facility were available that would filter out unwanted cosmic radiation. Encouraging progress has been made in satisfying the criteria for such a facility with the selection of the Homestake Mine in Lead, SD, by the National Underground Laboratory Committee as the recommended site for a National Underground Science Laboratory (NUSL). The Homestake Mine is America?s oldest and deepest underground mine, and its well-maintained infrastructure to depths of 2438 m below the surface makes the mine an excellent site for such a laboratory. The investigation reported here is an initial study of the stability of the first of the proposed chambers. A cylindrical room with a dome-shaped roof and floor was analyzed in three dimensions using the finite-difference program FLAC3D. The results were compared to recommended support requirements based on Barton?s Tunneling Quality Index, Q. Based on model results and observations from previous mining studies, large rooms with 50-m roof spans can be constructed and will remain stable at 2141 m below the surface in the Poorman Formation when the rock is reinforced with cable bolts. Construction may be possible at lower levels in the Yates Formation if more extensive laboratory strength tests confirm initial results.

Jan 1, 2002

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By C. B. Manula, R. L. Sanford, R. A. Rivell

A generalized flow diagram is presented in Figure 1, which shows the relationship of major model functions. This chart does not necessarily represent the anatomy of the computer program, but is designed to illustrate the informational interchange between major model functions. The related flow-charts-and computer program are listed in Parts I and II, Appendix A, respectively. Mine Car Stations The mine car stations are the activity centers for the model. The locomotive logic structure is designed to provide these stations with adequate cars and to clear them of car buildup. The model is designed to simulate a three stage haulage situation which suggests the need to differentiate station levels by type numbers. These are: a) TYPE 1 stations - mine cars are loaded here; b) TYPE 2 stations - intermediate stop and storage for mine cars; c) TYPE 3 stations - all mine cars that are stored here leave mine; and d) TYPE 4 stations - mine portal. TYPES 1, 2, and 3 have all loaded cars assigned to an ascending TYPE as their next destination. In input, if single stage haulage is designated, TYPES 1 and 3 do not exist, and if two stage haulage is called for, TYPES 2 and 3 are absent. A motor is not permitted to exchange cars between stations of the same type. Station Status Update. One major model function is to continuously evaluate the status of each mine car station. The major evaluations

Jan 1, 1974

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.

By D. R. Tesarik, M. K. Larson, J. P. Dunford, E. G. Zahl

Western coal mines are operating under increasingly challenging ground conditions. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are cooperating with mines to evaluate how these conditions affect mine opening stability and related miner safety. A system was developed to monitor rock and coal stresses during mining of an entire longwall panel. The system was designed to generate data in near real time to evaluate rock behavior in roof strata and the onset of hazardous conditions as overburden stress was redistributed over working entries during gob formation. Computer simulations and in-mine evaluations were used to optimize instrument placement. A prototype packer assembly was designed and tested for installing sensitive instruments in a mine roof. This paper provides background information on the stress monitoring concept and focuses on the development of instrument placement techniques and the prototype packer assembly.

By Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By George S. Rice, L. C. IlsLey

"A remarkable explosion of fire-damp caused by a discharge of lightning at the new shaft at the Sitalpur coal mine, has been reported by the Chief Inspector of Mines of India, who gave the following details:""The explosion occurred during a thunderstorm, and the evidence showed that a flash of lightning had, to all appearances, passed down the shaft caus¬ing disruptive discharges at certain points between the guides and the winding rope, rending the latter at two places situated respectively .228 .feet and 278 feet from the surface, The distance between the winding rope and the side of the shaft was 5 feet 4 inches, indicating a spark gap ;of this width, and an intensity of discharge which could not fail to ignite the explosive mixture of gas and air known to be present in the shaft.""The Compressed Air Magazine, January 1920 issue, which contained the above extract also goes on to state;""In 1915, M, Ferey described in a paper read before the Societe de l'Industrie Minerale phenomena of a similar character to the above. In a pit liable to sudden outbursts of gas, for the sake of safety, shot firing was carried out from the surface. During a storm, in the year 1905, shots went off in two places after the detonators had been connected to the conductors) we read in the Colliery Guardian, London. These shots were situated respectively 1,400 and 1,410 metres from the firing station, Realizing the possible danger from this cause, the precaution was taken to cut the conductors at the bottom of the shaft and to connect there just before firing, Even under these conditions a shot went off spontaneously, -.owing, it is believed, to lightning."""

Feb 1, 1920

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

6. Computer Simulation of Mine Evacuation Analysis of mine evacuation involves manipulating a large number of interacting variables, such as mine passages, hoist movements, miner position etc. , which makes the problem very difficult to solve without use of a digital computer. Therefore, under this contract, a computer program is written to simulate evacuation of a mine under different configurations. The simulation input variables include characteristics of the mine, expressed in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self-rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i. e , fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effect of the fire on ventilation or on the miners is not considered. The simulation output includes the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure time of the miners. Details of the mine evacuation program are summarized in Appendices A and B Appendix A describes structure of the program and its capabilities. The flexibility of the program and its suggested uses are demostrated by a number of illustrative examples Appendix B is a user' s manual for the program which includes instructions for program use and explanation of the logic employed in the program. A computer listing and printout of a typical output are also included in the Appendix B The ten illustrative examples summarized in Section A 4 (Appendix A) provide proof of validity of the program and help make certain inferences about mine evacuation. The first example, which is simulation of an actual mine fire drill conducted in a mine, has predicted evacuation time within 5 percent of the actual evacuation time in the fire drill, demonstrating thereby, the ability of the program to make accurate predictions.

Jan 1, 1976

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

By Maria I. De Rosa

Table 55 and figure 19 show the number of fires and fire injuries for stone mills by state during 1990-2001. Table 55 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 118 fires occurred in 33 states. Seventy-six of the fires caused 82 injuries (including 8 fires and 6 injuries involving contractors). The yearly average was 9.8 fires and 6.8 injuries. The Ewhr value was 873 x 106 hr (In = 0.019), and the LWD value was 1,911. Missouri had the most fires (16 fires and 9 injuries), followed by Pennsylvania (15 fires and 14 injuries), Michigan (9 fires and 5 injuries), and Virginia (7 fires and 5 injuries). Of these states, Virginia had the highest injury risk rate value (In = 0.09 1). Table 56, partly illustrated in figure 20, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries decreased during most of the periods, with a sharp increase during the last period. The number of employees' working hours increased throughout the periods. The In values follow patterns similar to those shown by the injury values. Tables 57-63 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 21 shows the major variables related to fires for 1990-2001. Table 63 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976