Search Documents

By E. H. McCleary

The Alamo Mine The Alamo mine is located about seventeen miles northwest of Walsenburg, Colorado, on the Loma Branch of the Denver and Rio Grande Western railroad, in the foothills of the Black Mountains of Huerfano County. Prospecting Mr. W. B. Lewis of New York City, president of the Oakdale Coal Company and also president of the Alamo Coal Company first became interested in this property in 1920. After all natural features of the surface had been carefully examined by Mr. Lewis, he was convinced that the property was underlaid with coal seams. Plans for prospect drilling were made at once and this drilling was started late in 1921. In all, eight drill holes were put down to the Trinidad sandstone which underlies the coal measures in this field. These drill holes in general, showed very satisfactory results. Two workable coal seams were penetrated by most of these drill holes, the upper seam being six and one half feet thick and the lower seam having a thickness of ten and one-half feet. The two seams are separated by forty feet of sandstone and shale. Analyses of the seams proved each to be of a very high grade bituminous coal possessing hardness much above other bituminous coals, and having very bright lustrous appearance. Tests of more than a year's duration proved the coal to store excellently in closed bins and also in open bins where coal is exposed to elements. The drill hole data further showed the coal seams to pitch more than fifty per cent or about twenty-six and one-half degrees. The pitch direction being approximately South 65 degrees East. The drill holes further proved the coal seams did not outcrop at any point on the property, and no evidence of coal outcrop has been found in near vicinity. A splitting and pinching out of seams was found to occur some two hundred to three hundred feet of theoretical outcrop at very Western boundary of property. The most Easterly or No. 6 drill hole has a depth of eight hundred fifty feet to floor of lower coal seam. The Trinidad sandstone was found to be immediately under the lower coal seam, and the Pierre shales lying under this sandstone. Plans for Development and Sinking Having obtained sufficient data, plans for development of the property were carefully made sometime in advance of the actual opening of the mine. Every condition was carefully studied and the maximum production of clean and well prepared coal at as low a cost as possible during the entire life of mine was kept uppermost in the minds of all. The life of mine is estimated at approximately fifty years. It was decided to open up the lower and thicker seam first, and due to the pitch and other conditions a slope opening was decided upon for its extraction. The pitch of the coal having been found to be from fifty to sixty per cent or twenty-six to thirty degrees, the plan of driving the slope directly down the pitch of seam was eliminated and a plan that would give a more economical grade was decided upon. To obtain a lesser grade, a point several hundred feet west of-and at a less elevation than the theoretical outcrop of coal seam was selected for the slope opening. (Fig. 18.) To have driven directly down the pitch of coal seam would also have given the slope an uneven grade as the pitch of coal seam varied as it approached the crop. From this point of opening, the slope was to be driven on a thirty-one per cent, or' about seventeen degree pitch to intersect coal seam in No. 6 drill hole, a distance through the Pierre shales and Trinidad sandstone of two thousand five hundred fifty feet, the slope to be driven practically due East

Jan 1, 1925

By G. A. Knox

Mr. Chairman and Gentlemen: The subject assigned to me would cover a great many pages if it were gone into thoroughly. Therefore. I have just touched on a few of the most important points. I think that everyone engaged in the production of commercial coal understands all about its preparation, but I will set forth my views as to how I believe it is best accomplished. In order to produce the best prepared coal, your first attention should be to the miner at the working face. The most careful system of blasting should be adopted to avoid heavy charging of holes which results in the shattering of the coal. The lump, or any other screened sizes that may be screened from coal that has been improperly shot, are subject to greater degradation in transportation and handling, as well as reducing screened sizes, which results in dissatisfied customers in the first case, and lower realization in the latter.

Jan 1, 1928

PRESIDENT WETZEL: The meeting will come to order. We are pleased to see a few of the more hardy survived last night's-ordeal and are present this morning. The Secretary has some correspondence which he will read. SECRETARY WHITESIDE: Gentlemen, I have a couple of telegrams and a letter which I would like to read to you at this time. First, a telegram addressed to Mr. Wetzel: "Regret greatly necessity canceling my plans to be present at meeting. Appreciate your conveying my best wishes to members for successful and profitable session.

Jan 1, 1942

Jan 1, 1971

Jan 1, 1941

By O .. G. Sharrer

Loading mechanically has of late become the most widely discussed subject in connection with coal mining and has even equalled. the discussion of safety measures as a topic of interest. The subject has been discussed in the various mining journals and by well. informed persons at the Mining Institutes, so it would appear; that all has been said that can be said until further experiments bring out new lines of discussion. It is, therefore, not the intention to present this article as a technical discussion of the subject of mechanical loading as a whole, but rather as a plain talk on machines with which the writer has had personal contact. In 1919, during the first period of post-war depression, a Pennsylvania coal company employing union labor became interested in the possibilities of mechanical loading with the hope of reducing their mining costs, which were and are yet too high to meet competition from the non-union fields of Somerset and Westmoreland counties. Of several loaders presented for their consideration the model of the Joy loader shown by Mr. Joseph F. Joy, seemed to hold the greatest possibilities, and after extended study, the management decided to invest in a machine of this type. A machine was built, which as far as the writer knows was the only one of its type ever put on the market. This machine arrived at one of the mines early in 1920 and was put to work immediately. It was a forerunner of the present 4-BU and 5-BU types, but differed from them very radically as to design. In general the machine consisted of the familiar Joy gathering arms and a short conveyor which discharged into a steel tank which held about four and one-half tons of coal. This tank was emptied by a second conveyor which placed the coal in the mine car. The object of this conveyor tank was to provide storage room while changing cars and to allow the machine to load on the entry while the room was short. This plan was very efficient and from our experience was worth retaining, but has been abandoned by the Joy Company on account of its making the machine unwieldy. The whole machine was mounted on caterpillar tractors which were driven by two 10-H.P. Westinghouse series wound motors, each having its own controller, the controllers being arranged in tandem so as to be operated by the same handle. This very ingenious scheme which is shown in Figure 4, was supposed to make it possible to steer the loader by the controllers. By swinging the handle one way both motors moved forward, by swinging the handle the other way both motors moved backwards and by twisting the handle as shown by arrows, one motor moved ahead and the other back, thus causing the machine to turn. This scheme proved a failure as the loader was too temperamental and erratic in its operation. After Mr. Joy, himself, narrowly escaped serious injury, this device was taken off and the controllers manipulated separately. This system never proved satisfactory and was abandoned' for

Jan 1, 1925

By C. H. Trik

Any article or discussion on the ventilation of Working Faces under different systems of concentrated mining is of little value to any practical man unless based upon facts gleaned from actual experience, and empirical data on this subject is, to say the least mighty scarce. Of this one thing, however, you can rest assured, the old cry of "no air at the working faces" will have become a thing of the past. No longer will we hear of some operator who has been too eager to get out the coal and who has lost sight of everything else in his mad dash for production, digging himself shut until his airways are mere pin- points and his air current a feeble thing, too weak to combat the high resistance of his restricted mine. A mine operating under one or more of the various systems of concentrated mining should always have plenty of air, for in concentrated mining the tendency is toward greatly reduced mine resistances due to increased sectional areas. It can readily be seen that the tendency is to large, wide areas across the panel and where this is true large volumes and low gauges are the rule, unless inordinate restriction is encountered in the permanent airways, and no operator, far sighted or progressive enough to adopt this system of mining when his conditions permit, would ever allow his main airways both intake and return, to be anything but model courses. As a matter of .fact, we are likely to encounter the opposite of what is usually the case in most mines to day. We are apt to find the air at the working faces sluggish due to the large areas of passage rather than to high resistance. This is combated in. various ways which will be discussed further along in this article. Those companies, of which we have knowledge in this country who, to- day are using any of the new systems of mining, seem to proceed alike in the general method of developing their acreage. Let us assume, for this discussion, the Utah Colorado Coal Corporation is going to open a mine under the new system and their conditions are such as to permit their adopting the simple block system, each face served by a separate machine, each entry having its conveyor to the cars. After the permanent haulage and airways are driven "narrow work" starts to shape the blocks. We are not interested in the length of these "conveyor headings" since we do not need to drive breakthroughs nor build stoppings for ventilation until we have reached their end when we connect them together. We have two methods of sending air to the face of these dead ends. We can laboriously and expeilsively install brattice cloth, as we go, or we can use a small auxiliary blower with canvas tubing to the face. Indeed I may say that one of the great difficulties encountered under the new systems is in the ventilation of these narrow faces. After they have been connected and an air circuit or current established, ventilation becomes plain sailing until the block is worked out. The auxiliary blower when used with flexible canvas tubing, has been found to be the ideal answer to the question of how to ventilate the headings which are anywhere from 100 to 1,000 feet long. These small blowers when properly used, can go a very long way to assist in further reducing the cost of production already assured by the new method of mining. Right angle bends are made by the tubing manufacturers to enable the fan to sit in the fresh air current, yet out of the way of operations and any recirculation is positively avoided by blowing the air around the corner to the face.

Jan 1, 1926

Jan 1, 1980

By D. J. Griffiths

Beyond doubt it is practically impossible to eliminate all chances of accidents from falls. Mother Earth is not going to give up her treasures without some sacrificing on our part. This particular question ranks among the important subjects connected with coal-mining, and has been given less attention as a factor of life- and limb-destroyer than any other cause. The single fatalities which happen create very little attention; nevertheless, when counted up at the end of the year, they outnumber the unfortunate ones that are mowed down by the wholesale by mine explosions. Fire-damp and coal dust were often considered the greatest evils in coal-mining. All records, however, prove this conclusion to be wrong. The second annual report of the Bureau of Mines gives the loss of life caused by falls of coal and roof in 1910 as 1,310, and in 1911 as 1,321. The reports of Pennsylvania mine inspectors for a period of thirty-three years show that 59.38 per cent of all the accidents underground were caused by falls of roof and coal. Also, the Bureau of Mines shows in its last issue on fatalities that accidents from fall of roof and coal killed more men than any other two causes combined, and that they account for more than half of the deaths under- ground. It seems we are getting too accustomed, taking too many things for granted, running too many risks, trusting too much for the best, and preparing too little for the worst. We must remove the cause; then the effects will cease. However, I can see that a better day is here. The main damaging factors underground are falls of roof and sides. A bad roof is tender and lacks the adhesive qualities to sustain its own weight over comparatively small areas. A roof of any character which is frequently penetrated by well-defined slips and cleats, is characterized as a treacherous roof. The carelessness of men has been one of the main causes of most of the accidents in mining as well as in any other industries. Three Grades of Miners Miners can be classified into three distinct grades, to-wit: the experienced and careful, the experienced and reckless, and the inexperienced. The accidents which the first class usually meet with occur through the carelessness of their co-workers, as well as through accidents which are termed unforeseen, such as falling roof between timbers, and between the timbers and the face of the coal. This may have 'previously given evidence of being absolutely sound and safe, but be released by invisible slips or by sudden outburst of occluded gases in large quantities, as we term big blowers or feeders,

Jan 1, 1913

By Gilbert Davis

MR. DAVIS: When the Secretary asked me to continue our accident experience in safety work at Dawson to cover the year just closed, I rather felt that he was asking 'a good deal, for we had said about everything that we could last year. I am not going to say very much, but in line with his request I have merely brought the figures up to date. I want to say, to start, that 1934 was, rather disappointing. It was the poorest year since 1930, as you will notice (indicates on diagram). This first column represents the accidents per thousand shifts worked. We cannot assign any real valid reason for the increase. We think we worked just as hard, but we are rather inclined to lay it onto the times; in other words, to lay it to the unrest and the changing conditions that are existent not only in this country but probably all over the world. We had twelve lost time accidents last year. As I explained last year, a lost time accident with us is an accident wherein the injured man is not able to return to his regular work, the next day-the day following the injury. So this represents (indicating) the lost time accidents per thousand shifts worked. We had one fatality in the twelve accidents which is reflected in the severity rates, which are also based upon thousand shifts worked instead of per million hours. The reason we are on the thousand shifts worked is be¬cause the Copper Branches of the Phelps-Dodge Corporation are all kept that way, and we are on the same basis for easy comparison.

Jan 1, 1935

Jan 1, 1981

By NA N/A

Jan 1, 1931

Jan 1, 1930

By Kraig R. Naasz

Jan 1, 2008

By I. N. Bayless

The subject of Premium Payments for Mechanical Loading was given consideration by the management, having in mind they would prove an incentive for increasing the tons per man shift, make for a lower production cost and allow the ambitious workman an opportunity to augment his earnings over the regular day wage rate, a standard of performance having been established by the operator which would be expected from the employee. Any performance above the standard is looked upon as a saving to the operator of which the employe benefited to the extent of receiving a certain percentage of the saving effected. The premium must be high enough to be worth while to the employee and low enough to in¬sure a saving to the employer. This method of sharing tends to pay men in accordance with their ability and effort. One of the principal advantages of this method of sharing is that a better class of labor may be attracted. Greater earnings furnish an incentive to increased tonnage. Workmen who prove themselves aggressive are readily noticed by supervisors, and, by shifting men to different places and to different working conditions, the crews are made more efficient and the inefficient workmen may be singled out and eliminated, thus permitting better results and better operation of the mechanical loading equipment. This is also evidenced by the fact that men become their own competitors, also working in competition with other crews. In order to do this, without neglect to the care and protection of the loading machines, men are educated to the proper handling and care of the machinery, keeping it in shape and everything clean in general, which has shown good results.

Jan 1, 1932

PRESIDENT LITTLEJOHN: Gentlemen, you have heard Mr. Dyer's paper. The meeting is now open for discussion. MR. NORMAN: I would like to ask the gentleman what is the distance between your crosscuts for the ventilation of rooms and entries in the state of Utah?

Jan 1, 1925

PRESIDENT MOSES: I thank you, Mr. Emrick. Mr. Shubart would like to supplement your paper with another article. SECRETARY SHUBART: My paper really should not supplement Mr. Emrick's paper, because I secured some data from him, I knew Mr. Emrick had had a great deal of experience in shearing and I thought he could give you some useful data. (Here Mr. Shubart read the following:) "For the past two years, there has been considerable discussion among coal mining men concerning the advantages of a shearing cut in addition to the undercut, in mine work. We have had a number of requests for information on sheared coal. We were asked questions like these: What percentage increase in lump can be obtained from sheared coal? What has been the experience of mine men who have employed the shearing cut? Is the shearing cut a means of increasing the lump content? If so, is it increased to such an extent as to warrant the installation of shearing machines? Upon investigation it was found that no one could give us any definite information on the subject as no one had weighed separately the grades of coal produced from' the shearing cut. With a view of getting this information first-hand, the Goodman Manufacturing Company built up a shearing machine to be used in experimental work only. The officials of the Troy Coal Company were eager to share in the expense of obtaining this information, so that in May of this year we shipped to their mines our first type 319 shearing machine. The Troy Coal Company operates a mine at Troy, Illinois, in the No. 6 seam and produces about 275 tons daily. The coal seam averages five and one-half feet in thickness. Previous to the arrival of the shearing machine the coal was undercut six feet deep by a' Goodman Shortwall Machine. To break down the coal required two shots in the entries and three in the rooms. The percentage of lump measured over two-inch screens, averaged 58.2 per cent. The conditions of the mine were very favorable for obtaining accurate weights on the amount of lump and slack coal run over the shaker screens. The shearing machine easily cut the entire tonnage of the mine so that all coal dumped into the railroad cars had been produced from a shearing cut, in addition to an undercut. Accurate records were kept of the railroad weights and front this data the percentages of lump and slack were computed. During the month of June the percentage of lump produced over two-inch shaker screens was 69.9 per cent. This result demonstrated that the introduction of the shearing cut had increased the percentage of lump twenty per cent. The entries were driven ten feet wide and the rooms thirty feet wide The shearing cut was made near the center of the face in all places. A hole was drilled in each rib and the coal shot down with one-half the powder required when the places had been undercut only. The coal was broken down to the back of the cut so that very little pick work was necessary to load it out. The benefits derived from the shearing cut were as follows: 1. Increased percentage of lump, thus increasing the average price of coal per ton. 2. Preservation of a tender top due to the decreased amount of explosive used. 3. Facilitated handling of coal by the miner thus increasing the tonnage per man. 4. Eliminated coal yardage in entries and crosscuts of ten feet or less in width for the reason that the shearing cut provides a loose end from which to shoot the coal. This applies to the union fields only, as the non-union mines do not pay for coal yardage. Based on a price of $2.50 for lump coal and $1.25 for slack coal, the average price per ton was increased

Jan 1, 1926

Jan 1, 1928

Jan 1, 1953

John P. Thomas, President. B. W. Snodgrass, Secretary-Treasurer. San Andrews, mine boss, Morley. Richard Bickerton, Tabasco. E. P. Bayles, superintendent, Cokedale. Clyde Campion, parting tender, Valdez. O. C. Cook, 406 East Seventh, Street, Trinidad. James Cameron, superintendent, Hastings. Charles Chambers, superintendent, ,Sopris. Arthur Dennison, Trinidad. Samuel Dean, mine inspector, Delagua. F. S. Dunlevy, assistant engineer, Hastings. L. R. Douglas, assistant engineer, care Danford & Sanderson, Trinidad. W. E. Danford, superintendent, Segundo. M. O. Danford, superintendent, Cedar Hill Coal & Coke Co., Trinidad. John Dougherty, mine foreman, Morley. J. C. Davidson, timberman, Valdez. William Easton, fire boss, Valdez. George Fortune, electrician, Primero. D. J. Griffiths, chief mine inspector, Trinidad. J. E. Hanes, assistant engineer, Hastings. Joseph Haske, superintendent, Primero. O. C. Erwin, electrician, 714 Pine Street, Trinidad. R. J. Jinkins, superintendent, Morley. Thomas jolly, superintendent, Gray Creek. James Jamieson, assistant mine boss, Valdez. James Kilpatrick, fire boss, Tobasco. L. M.. Kuhns, first-aid miner, care Mine Safety Car No. 2, Trinidad. William B. Lloyd, 404 East Seventh Street, Trinidad. J. C. Lawrence, machinist, Starkville. R. A. McAllister, mine inspector, Trinidad.

Jan 1, 1913