Search Documents

By J. Labuschagne

The primary factor contributing to the profitability of a platinum mine and its associated concentrator is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. To minimize the time it would take to produce concentrate without stopping because of a lack of feed material a project was undertaken to integrate the mining model with a concentrator production schedule () in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where ?visual pollution? is to be avoided. To achieve this a dynamic stockpile model was created utilizing the mine production schedule resolved into a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ores. The stockpile levels were never allowed to fall below zero to prevent a situation where the concentrator was operational without feed material,. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, that was then used as a basis for commercial concentrate sale negotiations.

Jan 1, 2012

Copper cyanide is a common component of cyanide-treatable precious metal ores. The copper concentration in production heaps can be predicted from laboratory column tests, but the exact correlation is not necessarily intuitive. Generally, heap leach operators like to keep copper concentrations in solution below 300?500 ppm and may note problems with gold recovery and cyanide consumption when copper concentrations exceed this amount. There are several methods of copper removal from cyanide solutions including ion exchange; direct electrowinning; acidification, volatilization, and recovery (AVR); and sulphide precipitation such as the sulphidization, acidification, recycling, and thickening (SART) process. SART involves acidification with addition of soluble sulphide, separation of the resulting copper sulphide precipitate, and addition of lime to re-establish alkalinity prior to returning the solution to the leaching process, recovering both copper and cyanide as valuable products. In principle SART is very simple. Yet some SART plants that have been built may have been unnecessarily complex. This paper explores the basics of SART and makes the case for a simple plant design as applied to the heap leaching circuit.

Jan 1, 2012

By T. Ellis, J. Gagnon, L. Webb, M. Burr, D. Kakengela, D. Evans, A. Mirza

Lead-based alloys are used as the primary anodes for electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present-day lead-calcium-tin alloys for copper electrowinning and leadsilver alloys for zinc electrowinning. Anode technology has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion, which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. A balance of alloying element selection and microstructural design allows the grain boundary area to be engineered, thus minimizing grain boundary corrosion. However, operational issues can lead to unexpected corrosion behaviours that we will discuss moving forward. The comments in this work, although directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The life cycle of electrowinning anodes depends on tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead anodes for base metals electrowinning.

Jan 1, 2016

By G. P. Dyke

The MRMR classification system was developed specifically for mining applications, namely caving operations, and is one of three rock mass classification systems used in the South African mining industry today. Increased usage of the MRMR classification system has raised concerns that it does not adequately address the role played by discontinuities, veins and cemented joints in a jointed rock mass. To address these concerns, Laubscher and Jakubec introduced the In-Situ Rock Mass Classification System (IRMR) in the year 2000. Although the IRMR system is more applicable to a jointed rock mass than the MRMR system, a quantitative comparison of the MRMR and IRMR classification systems indicates that there is not a significant difference between the resultant rock mass rating values derived from the two classification systems.

Jan 1, 2008

By E. E. Almási, G. Mucsi, G. Rákhely, Á. Rácz, B. Csőke, Zs. Pap, K. Bohács, N. Halyag

Wet stirred media milling is a widely applied grinding process in the field of mineral processing to produce <10 μm ground materials. In this paper, the results of wet stirred media milling of different Ti, Fe and Cu-oxide and phosphate minerals are presented. During the experimental work, grinding of ilmenite, vivianite, hematite and cuprite was carried out in a continuous operation wet stirred media mill. During the experiments, the particle size distribution and specific surface area of the ground materials were determined after a certain grinding time, as well as measuring the specific grinding energy, thereby determining the grinding kinetics of the different minerals. The measurement results showed the differences and similarities in the grindability of the individual minerals. Nano particulate vivianite, hematite and ilmenite was successfully manufactured in a stirred media mill; however cuprite was characterised as the coarsest final product for the same grinding circumstances. Keywords: Wet stirred media mill, cuprite, vivianite, ilmenite, hematite

Jan 1, 2020

By N. Steven

Published parameters from the Mufulira copper in situ leach (ISL) in Zambia are used for order-of-magnitude flow-rate calculations for an envisaged gold ISL in back-filled Witwatersrand stopes. A successful leach operation requires that the porous medium, usually a sand, has a hydraulic conductivity in excess of 5 x10-7m/second (i.e. a permeability >50 millidarcies).Empirical evidence suggests that average linear velocities would be of the order of 60 m/day if the backfill has the grain size of a fine sand. The proposed gold lixiviant would probably be an alkaline or ammonium thiosulphate, not cyanide. The resultant sulphate-rich ground and drainage waters could probably be processed using existing purification techniques to produce gypsum and magnesium/calcium carbonate. Within the next 100 years it is inevitable that solution mining will find widespread application on the Witwatersrand, if not for gold extraction, then certainly for water remediation purposes.

Jan 1, 2009

By J. Portal

One of the key products produced by the mineral sands industry is the titanium dioxide slag, a process that requires grinding of a coarse product down to a valuable saleable product. Traditional methods have included the vertical roller mill in tandem with dynamic air classifiers and, alternatively, two-stage grinding and crushing through an AG mill in closed circuit with a dynamic classifier and secondary gyradisc crushers. The products produced, commonly known as chloride and sulphate slag, are differentiated by the particle size distribution of the final product. The more valuable chloride slag must, by specification, be a product sized in the range between 850 and 100 microns?the more fines generated in the grinding process, the less higher valuable final chloride slag is produced. This paper will explore a technology that is new to both the mineral sands and to other mineral processing industries. Inter particle communition, or IPC as it is known, has been applied in the cement industry to improve the performance of clinker grinding mills. The principle is to create a process of material on material comminution under high pressure that fractures the material along the grain boundaries rather than breaking it smaller than a gap setting in the crusher. The process is now looked at for the TiO2slag producers because of the potential benefits of energy savings and with a minimal generation of minus 100-micron fines. Discussions will revolve around the design and functionality of the Rhodax® both from a process and maintenance perspective, a typical test regime and results on slag grinding. The development of the flowsheet necessary for the process will be examined, the ancillary equipment required and finally the scale-up from the test to an industrial plant will be investigated. Full-scale results of an operating plant will also be given showing the benefits that can be realized. A promising new flowsheet with fines reintroduction to the Rhodax® crusher will be presented.

Jan 1, 2007

By Z. Song

Real-time monitoring makes it possible to detect any disturbance occurring in production, while decision instruments can efficiently assist decision-makers to optimize production, reduce iterative workload, obtain better solutions, and preview possible results. Technologies for the above already exist and have been proven in the process industry, i.e. refining and smelting. Optimization is also essential for profitable and stable mining production. Real-time monitoring has already taken hold in mining operations, especially in surface mining, while optimization techniques have also been widely used in underground mining, particularly for planning and scheduling. This review is limited to the hard-rock mining production of metallic ores such as gold and copper. It reviews optimization techniques developed for mine planning and scheduling, and communication technologies suitable for underground applications. It also presents control features for individual operation units, and discusses the technical viability of a mining production real-time optimization (MPRTO) system for underground mines, with possible benefits and challenges. Operational disturbances always occur in mine production. An MPRTO system can be useful to maintain operational effectiveness and efficiency by allowing quick changes to short-term plans. This paper briefly describes the MPRTO system, including the input, output, and basic algorithms. The technical prerequisites for the system specified here are already available. Further studies that are required to improve the system are discussed. Keywords real-time optimization, underground mining, production, operation.

Dec 1, 2013

By J. A. Maree

After the South Deep complex was purchased by Goldfields in 2006a re-feasibility study was done and the life of mine (LOM) was extended to 52 years. This also implied that the mine?s infrastructure would have to be enhanced. One of the changes was the proposal of five new main orepass systems to be excavated before the mine reaches full production in 2013. Excavations started to show signs of scaling, and in some cases, whole new excavations were lost. This particular area was exposed to very high stresses and the geology was prone to body delimination rendering the relevant areas unstable. This paper investigates the conditions at the location of one of the proposed orepass systems, and the best possible orientation was suggested to ensure that the orepass system would be stable and have a practical life. It was, however, found that the fourth leg of the orepass system would require further support to be classified as stable by the chief rock engineer and the section geologist of South Deep. Several support methods and orepass system linings would then be analysed and evaluated to give calculated recommendations on how to productively and practically support an orepass system. Keywords Main orepass system, stresses, body delamination, impact and abrasion, rock support, concrete lining.

Jan 1, 2011

"Sampling error and bias, especially the Increment Preparation Error (IPE), are introduced when the tool allocated to do the job fails to extract a representative sample. This is the case with chip sampling; the tool can only extract haphazard shapes of loose or fractured material and not always from within the demarcated sample area. Increment Extraction Error (IEE) and Increment Delimitation Error (IDE) could be severe, but are found to be relatively unbiased. The uncontrolled action of the sampler in discarding excess sample material after sample collection has a significant impact on the error and bias introduced with each and every extraction. A new type of bias, referred to as the ‘waste discard bias’, arises when samplers select what portion of the excess sample material to discard at the sample site. Material visually identified as waste is discarded in preference to mineralized broken ore if there is an excess of sample material. This results in a considerable error in the analytical results. The bias is proportional to the reef-waste ratio in the demarcated sample. IntroductionTwo types of ‘sampling’ are distinguished, namely sampling of particulate materials (broken ores) and sampling of solid, unbroken in situ mineralized reef. This study considers only chip- or face-sampling of in situ, goldbearing, carbon-rich conglomerates typical of the Upper Witwatersrand Supergroup and examines where components of sampling error and bias, clearly specified in the Theory of Sampling, may arise during the practice of ‘face sampling’. Many millions of face samples have been extracted from Witwatersrand-type mines using a hammer and chisel, and detailed descriptions (standard operating procedures) of how the samples should be taken have been developed by many mining companies. There is, however, no taxonomy or nomenclature for managing or reporting the different types of errors associated with chip sampling. The Theory of Sampling compiled by Pierre Gy in the early 1950s provides, comprehensive nomenclature of sampling errors that is applied to particulate sampling of ore in a lot, a stockpile, or a moving stream on a conveyor belt. The taxonomy and characteristics of sampling errors, grouped according to the sources from which they arise, and identified by Gy (1973, 1979, 1982, 1992, 1995, and 1998) are shown in Figure 1. This classification of errors is used extensively in regard to the sampling of particulate materials in the mining and minerals industry, but not in regard to chip sampling. A relatively small mass (hundreds of grams) of representative particulate material for estimating the average grade of a much larger mass (thousands of tons – the ‘lot’ in the Theory of Sampling) is extracted by the chipping or cutting of a representative rock ‘sample’ from the stope face."

Jan 1, 2016

By M. Mpofu, B. Maphalala, S. Khan, S. Ngobese, D. Roberts

This paper details an assessment of stemming practices at a South African opencast coal mine and their influence on ground vibration and air blast. Quantitative and qualitative analysis methods were used for the study. The parameters assessed for the quantitative analyses included stemming length, stemming material type, blast-hole depth, burden, and spacing. Pre-blast data from the mine was analysed to determine the deviation between actual and mine design stemming parameters. Mine design stemming length was also compared to the rule-of-thumb stemming lengths. Peak particle velocity (ground vibration) and air blast data from seismograph stations around the mine was analysed to determine the correlation between stemming length and excessive ground vibration and air blast. The qualitative analysis involved observations of blasting procedures at the mine to determine compliance with mine procedures. Some level of non-compliance of actual stemming parameters to design stemming parameters was found, which initially suggested that non-compliance may have contributed to excessive air blast. However, further analysis of the seismograph results indicated no direct correlation between stemming length and excessive air blast and ground vibration. Since stemming parameters are interrelated, it is crucial that all blasting procedures, including stemming, are executed in accordance with best practice, and recorded accurately. There is a need for digital systems for capturing on-bench blasting parameters, as the currently used manual data recording and reporting systems are inefficient and prone to error. Improvements to blast designs are possible through efficient and accurate data recording and reporting systems.

Jan 1, 2021

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

By D. G. Almond

Low-grade, complex mineral deposits have resulted in the need for complicated large-throughput processing plants delivering increased productivity, reliability, and utilization, together with reducing operational costs. Complex mineralogy has resulted in complicated process flow sheets designed to recover minerals as efficiently as possible. In addition, the remote location of many minerals¬-processing plants, continuously rising energy costs, and fierce competition pose significant challenges to the modern mine, compounded by a global scarcity of qualified and experienced operational personnel. Over the last decade the Internet and automation technologies have undergone major advancements. Automation technologies, solutions, and concepts that existed, but were considered risky or unreliable prior to the year 2000, have now gained acceptance and matured. Furthermore, new technologies and different collaboration schemes have appeared, offering innovative solutions to the mining industry to address many of the challenges described. These advancements in reliable remote systems that access technology through the Internet provide significant opportunity to support mining operations, enhance process performance, provide engineering services, and proactively anticipate and execute maintenance services. This paper references a global survey of automation trends in the mining industry and the potential for an intelligent collaborative environment using automation technologies to exploit opportunities in operating the plant of the future, increasing effectiveness, and reducing operational costs. A variety of possibilities are described, including asset management solutions, remote access capabilities, performance monitoring solutions, advanced process control technologies, and the formation of an intelligent collaborative environment. A real example where this technology is used to support the operation and maintenance at a cement plant in Egypt is given to underpin the concepts described in this paper.

Jan 1, 2013

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By C. I. Ware

The phrase ?back to basics? is used to describe the fundamental principles and philosophies on which a successful mining operation is based. At Richards Bay Minerals (RBM), ?back-to-basics? (BTB) has been implemented as a continuous process to probe operational functions with a view to increase production without capital expenditure. It also ensures that the fundamentals of dredge mining are understood and adhered to. BTB is based on the principle that people drive organizations, necessitating an interactive implementation approach. At the RBM mine this entails a three-pronged approach, namely practical training, teamwork initiatives and the use of lean Six Sigma methodology. It is the latter on which this paper will focus. The lean Six Sigma methodology is successful in identifying, managing and documenting BTB projects, while team work initiatives are integral to successful project implementation. This paper describes two examples of how the Six Sigma methodology can be applied to a dredge mining operation. The first example focuses on the improvement of Mining Pond Echo (MPE) plant throughput by reducing the lost opportunity (non-production) due to tails downtime. The project was successful in increasing plant throughput by 4.5%. This was achieved by increasing the tails disposal system availability by running MPE as a four tails lines operation and focusing on causes of tails production downtime. Subsequently, the tails system at MPE is no longer the production bottleneck. Second, the Six Sigma methodology was successfully applied at Mining Pond Charlie (MPC) to increase the primary dredger throughput by 4.6% through focusing on the dredging technique and maintenance issues. This project highlighted the need for trend analyses to ensure an effective dredging technique, coupled with simple production documentation, which also ensures a focus on maintenance. Keywords: Back to basics, Six Sigma, training, teamwork, throughput improvement, tails, dredger.

Jan 1, 2007

By S. Kahraman

The prediction of rock properties from indirect testing methods is important, particularly for preliminary investigations since indirect tests are easier and cheaper than the direct tests. In this study, we investigate the predictability of the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of rocks from the indentation hardness index (IHI) obtained using point load apparatus. Forty-six different rock types, 14 of which were igneous, 15 were metamorphic, and 17 were sedimentary were tested in the laboratory. The UCS and BTS values were correlated with the corresponding IHI values and the results were statistically analysed. The influence of rock classes on the relationships was also investigated. A strong correlation between UCS and IHI was found for all data. The correlation between BTS and IHI is not as strong as the correlation between UCS and IHI, However, it is in the acceptable limits. When the regression analyses were repeated for igneous, metamorphic, and sedimentary rocks, the correlation coefficients were generally increased. The results show the UCS and BTS can be estimated from IHI, In addition, the effect of rock classes on the relationships between IHI and both UCS and BTS is important.

Jan 1, 2012

By R. Ciccu

This paper examine the optimization of a beneficiation plant for recovering marketable barites from crude ores of different characteristics. The plant, part of a mining complex in Sardinia, consists of a jig section integrated with a flotation line. The problem has been studied using a suitable model of the process, based upon experimental and field data pertaining to both the characteristics of the feed material and the performance of machinery. Data have been automatically processed with the aid of a computer to find the optimum setting of each section, in order to maximize profit for each kind of ore separately fed to the plant. Moreover, the advantages of blending the various concentrates - not all of them individually marketable - are also demonstrated. The overall economic result can be improved provided suitable proportions of each kind of ore are fed to the plant. Such information is fundamental for the long-term planning of exploitation of available reserves, and provides guidelines for further prospecting. The paper illustrates the washability characteristics of the ore&apos;s and describes in detail the model adopted. The results of data processing are then presented in the form of computer graphs and discussed. Finally, conclusions are drawn regarding the advantages of resorting to Operations Research as an aid to management.

Jan 1, 1987

By P. J. Kinver

This paper deals with the development of backfilling methods and systems at the Broken Hill orebody of Black Mountain Mineral Development Company (Pty) Limited, at Aggeneys in the north-western Cape Province. Production started in 1979, being confined to large diameter blasthole stoping methods in the upper, steeply dipping areas of the orebody. This blasthole reserve is now depleted and the production tonnage, 100000 tons per month, is produced from eight cut and fill stopes in the flatter dipping areas of the orebody. The fill methods of the blasthole stoping area evolved prior to the pillar extraction are briefly discussed together with the resulting experiences gained that enabled virtually 100% extraction to be achieved. The original cut and fill mining used costly hydraulic cemented fill; this was replaced partly by unconsolidated river sand and later by dune sand which occurs in abundance. The paper describes the planning, research work and commissioning of a cycloning plant that now enables dune sand to be used successfully as an unconsolidated hydraulic fill. The development of drainage, placement and control methods are also reviewed.

Jan 1, 1988

A number of issues relating to the computational aspects of pillar design are addressed in this paper. The computation of average pillar stress values is important when attempting to establish criteria for pillar design and in the analysis of the stability of tabular pillar layouts. One of the default ?classic? numerical methods that are used to determine pillar stresses is the displacement discontinuity method. In many instances it is not clearly understood that this approach does suffer from some limitations, particularly in relation to the fact that in coarse element simulations, the simulated average pillar stress (APS) can depend on the chosen mesh size. The nature of this error is highlighted in this paper and some strategies are suggested to bound the magnitude of these errors. It is demonstrated as well that the popular linear stiffness approximation to pillar or seam compressibility does appear to allow reasonably accurate estimates of the average pillar stress when either the pillar height is varied or when the seam modulus differs from the host rock modulus. A practical implication of this study is that if the seam modulus is noticeably lower than that of the host rock, such as for coal seams, it is important to use a linear stiffness constitutive model for the pillars rather than a ?rigid? pillar assumption. This added complexity seems unnecessary, however, when simulating hard rock pillars in mines where the seam modulus is very similar to that of the surrounding rock.

Jan 1, 2011