Search Documents

By D. D. Hawat

The locations of potential reserves of chromite ores throughout the world are discussed. Reference is made to the marked changes in international trade in chromite ores during the past ten to fifteen years, and to the change in locality of the production of ferochromium aloys, which is curently largely carried out in the country of origin of the ores. The influence of these changes has been very profound in South Africa, which has the largest smelting capacity and the largest production of ferochromium aloys in the world. A proportion of South African ore is stil exported to meet the demands for the production of chromium chemicals and refractories, including a large tonnage of foundry sands. Ferochromium smelters in South Africa have a capacity of virtualy 1 Mt of aloy per annum. Nearly al this development has taken place since the introduction of the argon-oxygen decarburization (A.O.D.) process for the smelting of stainless steels. Formerly, expensive Iow-carbon ferochromium aloys were required as raw materials, but the AO.D. process, which is being used world wide, permits the use of high-carbon ferrochromium, the main product of the smelters in this country. The production in South Africa of chromium-containing corrosion- and heat-resistant steels is stil on a relatively smal scale, but serious atention is being paid to the exploitation of low-carbon weldable feritic chromium steel.

Jan 1, 1986

By E. J. Magri, D. M. Hawkins

This paper deals with an experimental programme carried out with a gold analyser in the period June to September 1979 at Loraine Gold Mines. The results were found to be reproducible, with no overall or conditional bias when the measurements were compared with those obtained from chip samples. The standard error of estimation of a 3 m reef exposure, which was the sampling interval, can be reduced by a factor of 2,5 if the complete stretch is scanned, rather than the taking of one chip sample in its centre. Complete statistical and computational procedures were developed for the fitting of the normal-Iognormal model to observed analyser data and for the determination of the most likely gold grade for a particular analyser measurement. (This corection procedure is necessary since a significant number of negative analyser measurements can be observed.) Panel averages of uncorrected scans showed a small conditional bias relative to those of corrected scans. However, uncorrected panel averages can be used for on-the-spot decisions regarding whole panels. For standard calculations of ore reserves, use should be made of corrected scans. Under reasonable assumptions, the use of the detector in the selective mining of low-grade narrow reefs such as the Basal Reef at Loraine Gold Mines, when compared with the conventional chip-sampling method, can result in a saving of as high as R40 million in present-money terms over the life of a project. The difference could be even larger in a highly variable reef like the B Reef at Loraine Gold Mines.

Jan 1, 1987

By R. E. Phillips, L. A. Cramer, R. T. Jones

Atomaer (Pty) Ltd is a technology-driven company with interests in Western Australian nickel. Atomaer (RSA) Pty Ltd is a process technology company operating in Southern Africa. It is a subsidiary of Atomaer Holdings Pty Limited (Atomaer), which has operating companies in Australia, Africa, South America, and Europe. In addition, Atomaer has substantial shareholdings in Braemore Resources Plc, a nickel company with interests in sulphide nickel projects in Western Australia and Southern Africa listed on the Alternative Investment Market of London Stock Exchange (AIM); Mintails Limited, a gold company with interests in gold operations in South Africa listed on the Australia Stock Exchange; and Brinkley Mining Plc, a uranium company with interests in Southern Africa listed on the AIM. Independence Platinum Limited (IPt) has been formed by Atomaer to undertake the commercial development and exploitation of Mintek's ConRoast technology with the strategic objective of providing independent smelting and refining facilities with lower capital and operating costs for the treatment and processing of platinum concentrates, including those with high chrome and/or nickel and/or low platinum group metal values, for the development of platinum projects by junior resource companies in South Africa. The platinum mines of South Africa have traditionally exploited the Merensky Reef of the Bushveld Complex for platinum production. However, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the ore bodies at deeper levels. In the past decade, all of the platinum producers have begun to mine the UG2 reef because of its cheaper mining costs. UG2 ore usually has lower platinum group metal contents and higher chrome values. The new junior resource companies have gained access primarily to UG2 reefs. Consequently, platinum mining is becoming more UG2-based and the resulting concentrates contain high levels of chromitite. UG2 concentrates are difficult to smelt in the current six-in-line submerged arc furnaces, and this leads to increased capital and operating costs for those smelting operations. The platinum mines of South Africa produce the majority of the world's platinum metal used in automotive catalysts and jewellery. As the platinum market is forecast to grow at a healthy rate into the future, the SA producers Anglo Platinum, Impala, Lonmin, and Northam are planning to expand mining operations in the next decade. Furthermore, a number of smaller new producers who are accessing other mineral resources are entering the buoyant market and will produce platinum concentrates for purchase or toll treatment. Hence, a shortage in both smelting and refining capacities is anticipated. Further smelting and refining facilities independent of the major platinum producers will be required in South Africa by 2010. Mintek's ConRoast technology is best suited to fill the need to treat a high proportion of UG2 concentrates in a cost-effective and technically efficient manner. Atomaer base metals technology has been developed for rapid leaching of nickel and other base metals from alloy. Significant reductions in capital and operating costs are expected from the combination of the two advances in process technology compared with that installed at the existing smelters and refineries that were established over 20 years ago. Independence Platinum will be listed on AIM and the Johannesburg Stock Exchange (JSE) in 2007, and developed as an independent, vertically-integrated platinum company using its independent smelting and base metals refining facilities as a strategic platform to promote the development and mining of platinum projects by junior resource companies in South Africa through technical co-operation, strategic alliances, joint ventures, off-take, toll-refining, and marketing agreements.

Jan 1, 2006

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions.

Jan 1, 2012

By E. Moosavi, K. Tolouei

In mine production scheduling problems are well-known, where most are categorised into deterministic and non-deterministic NP-hard problems because of their complexity. Many researchers have attempted to solve the problem by applying various optimisation techniques. While using traditional methods they observed extreme difficulty in solving highly complex problems. In the 1990s, many researchers addressed long-term production scheduling (LTPS) by using simulated annealing, the genetic algorithm, the tabu search algorithm, and the ant colony algorithm. These algorithms are known as the meta-heuristic algorithms, and have proved to be the most efficient algorithms for solving LTPS thus far. The firefly algorithm is one of the best methods for visualising problems related to LTPS, and provides the best possible optimisation. It is one of the simplest methods, and easy to apply to any NP-hard problem. The experimental, and comparison with other recently published algorithms shows that the proposed algorithm is feasible, and is an effective approach for long-term production scheduling problems. The results indicated that a better solution is obtained by the proposed method, compared to other methods in terms of cumulative net present value, and average ore grade. Additionally, the CPU time via the proposed model is roughly 2.52% higher than the other method.

Sep 1, 2021

By W. P. C. Duyvesteyn, J. R. Cutland, J. R. L. Russell

In 1970 it was decided to build a large new plant at the Chingola Division of N.C.C.M., Ltd., to treat concentrator tailings and leach residues with a low copper content by a leach-solvent extraction-electrowinning process. In order to assist in the establishment of the design parameters for the new plant, and to study the interaction of this plant with the existing leach-electrowinning plant, mathematical models, formulated as linear programs, have been developed and used extensively. The paper outlines the metallurgy of the plants and describes briefly the way in which the models have been formulated and used. The formulation involved the use of separable programming to form the products of some variables.

Jan 1, 2014

By Daniel W. Kappes, Pierre F. X. Mousset-Jones

"In this paper a discussion is presented of a program designed to produce a 40-day production forecast for an underground stoping system.The program is intended to be a tool for the operations department in an underground mine, and is designed to utilize data readily available from production reports. Brevity of data input, ability to revise slope conditions easily and the accuracy of starting stope status are stressed. Applicability of the program to a wide variety of sloping methods makes the program potentially useful in a large number of mines.The general functions of the program subroutines, and input and output lists are discussed. An example is also given of a stope in operation for a three-day period, which shows how the program can handle production irregularities as they arise."

Jan 1, 2014

By Ronald J. Roman

All mining and milling complexes can, within limits, operate at a variety of production rates. Factors of economic importance that are affected by production rates are costs per unit production, recovery and product grade. Once the relationship between the production rate and cost is established, dynamic programming techniques can be used to define the optimum production schedule (that is, the production schedule that maximizes the present worth of the operation) for the life of the deposit. In general, assuming that the capacity and efficiency of the physical plant remain unchanged throughout the life of the deposit, the optimum production rate is not constant for the life of the deposit, but declines gradually as the deposit is being exhausted.

Jan 1, 2014

Jan 1, 1981

By R. J. MacAulay, R. C. More O’Ferrall

Preliminary tests on cement-consolidated gold-plant slime are outlined, together with preliminary underground tests on the behaviour of two paddocks of the material. Further large-scale testing of the same material pumped to the underground workings from a batching plant on surface is described.

Jan 1, 1978

By M. J. Robinson, G. E. Blight, J. A. C. Diering

The mechanism of the flow of tailings slurry is examined, and a mathematical model is derived to describe the flow. Predictions based on the model are then compared with the flow that actually occurred near the shaft at Bafokeng after the No. I tailings dam had failed. The predictions are found to be of acceptable accuracy.

Jan 1, 1981

By J. C. David, G. Coetzer

The effect of varying aliphatic, olefinic, and aromatic groups in the N- and S-positions of dithiocarbamates was investigated in the selective and bulk flotation of a mixed copper-lead-zinc-iron ore. Selective and bulk flotation were found to be dependent on the type of functional group, as well as on the position of substitution.

Jan 1, 1989

By J. A. Drummond

The duties and efficiencies of a number of main and auxiliary fans were determined by standard and thermal methods. Some observations on the effect of water and dirt accumulation on fan performance were made.

The 94th Annual General Meeting of The South Mrican Institute of Mining and metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 14th August, 1991. Obituaries The President announced the deaths of the following members of the Institute: Honorary Life Fellow and Past President

Jan 1, 1991

By B. Rainier

This paper discusses the preparation of material for backfilling operations using hydrocyclones. Aspects dealt with include the advantages and disadvantages, material requirements, process constraints, operating systems and equipment of the backfill plant.

Jan 1, 1988

By M. R. Henzen, J. W. Funke, G. J. Stander

SYNOPSIS The adverse effect of acidic mine drainage derived from gold and coal mining operations on the quality of receiving waters is described, together with measures to be taken to counteract this pollution. The mineral load and the toxic effects from metallurgical and metal finishing industries are also considered. Attention is drawn to water conservation aspects.

By C. R. Thomas

Although stainless steels have been used to a limited extent in the South African mining industry, the metallurgical development of 3CRI2 has presented materials engineers with a viable alternative for certain materials-handling applications. The various types of wear involved in these operations are described, and an explanation is given of how 3CRI2 is able to offer advantages, particularly in wet sliding applications. Certain applications result in various types of abrasive wear, and the performance of 3CRI2 in these areas is described.

Jan 1, 1981

By D. H. C. Griffiths, D. R. Davis, D. B. Paterson

Consolidated Murchison Limited is the only primary producer of antimony in South Africa, producing approximately 18 per cent of the total world production. This paper gives a technical review of the history, occurrence, mining, and metallurgy of antimony at Consolidated Murchison. World antimony markets are also discussed, together with the end-uses.

Jan 1, 1986

The FSPE Award for Services to the Engineering Profession was awarded to Or Francis George Hill at a ceremony held in January of this year by the Federation of Societies of Professional Engineers. The following is an abridged version of the citation made by Professor A.N. Brown, President of FSPE, and of Or Hill?s reply. Achievements. It is indeed fitting that such a distinguished group of people have gathered on this special occasion to honour and pay tribute to Or Pinkey Hill

Jan 1, 1988

By A. A. Hazell

Mine management by objectives By A. A. HAZELL The author discusses the objective areas of mine management. Setting objectives is seen to be a conscious process which starts at the highest level of management. This enables clear objectives to be set at each lower management level. The methods of setting objectives in the areas of stope production, productivity and manager performance are set out in detail. In the area of manager performance emphasis must be placed on the practice of management. It is concluded from results obtained that "management by objectives" produces better than average perormances.