Search Documents

By S R Grano

A fundamental model, which considers the subprocesses of particle collection by bubbles in flotation, is applied to two comprehensive flotation surveys in the rougher stages of C3 concentrator, PT Freeport Indonesia. The flotation surveys focused on the collection of: ? cell-by-cell and size-by-size metallurgical, ? cell hydrodynamic, and ? pulp and surface chemistry information. The two surveys were conducted at significantly different feed tonnages, giving rise to significantly different feed particle size distributions, pulp densities and mean pulp residence times. A series of model simulations are performed with the aim of quantifying changes in copper recovery, on both a size-by-size and unsized basis, with changes in values of the hydrodynamic parameters and hydrophobicity of the copper sulfide mineral. This was carried out in an effort to identify the most promising route to increase overall copper recovery in roughing. It was found that by increasing the hydrophobicity of the copper sulfide mineral surfaces it became possible to optimise cell hydrodynamics, which targeted increased fine (-12 µm) copper sulfide mineral recovery but without adversely affecting coarse (+150 µm) copper sulfide mineral recovery.

Jan 1, 2007

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the project's life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analysts' inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted `floor' value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

This paper presents a quantitative approach to the problem of determining design capacity and field dimensions of underground coal mines using room- and-pillar mining systems. In evaluating these design variables, relationships among mining costs, number of production sections in mines, location of central shafts, mine field dimensions, section production, mine output, and cost of production losses due to underground man-traveling are analyzed. Thereby the unit cost of coal is expressed as a function of the design variables as well as input parameters such as seam angle, seam thickness, seam depth, underground traveling speed of men, mine recovery and plant recovery. The problem is then formulated as a nonlinear optimization model in terms of minimizing the unit cost of coal subject to a set of constraints and solved analytically for flat seams and numerically for inclined seams. Sensitivity analysis of the variables is also included in the paper.

Jan 1, 1987

By L. Raaths

This paper outlines the process of improvement utilizing performance monitors and GPS systems on an opencast strip mine. Its primary focus is to maximize coal exposure by draglines and secondly to improve on those processes impacting directly on the dragline operation. The Aquila (DM2/5 system) navigation and monitoring systems were installed on the overburden drills. Their main function is to eliminate manual staking and positioning thereby ensuring a regular pattern being drilled. Holes drilled to planned depth reduce drill metres and it minimizes coal losses and contamination at the coal interfaces. The CAES (Computer Aided Electronic System) will be installed and evaluated on the Caterpillar D11 dozers at Optimum. This system ensures a correct dragline pad elevation through the use of planned elevations and GPS technology to achieve the optimal pad elevations for draglines consistently. The draglines are equipped with a Dragline & Operators Performance Monitor. This monitor allows the operator to control his own performance. It reports on all productivity, method and poor operating techniques. These monitoring systems send critical operational information back to the office. This source data resides in central databases from where it is converted and integrated into management information. To manage an operation means that you as a manager must be able to set objectives and targets and to achieve your goals the activities involved must be measurable.

Sep 1, 2001

In many practical situations, the samples available to estimate a block of ore are not located on a regular grid. The sample sizes and orientations are not constant, and the number and relative position of the samples used for valuation of each block change from block to block. Estimation of a block W might be very complex and time consuming if each sample in the neighbourhood of the block were considered individually. A practical solution consists of grouping the samples in blocks Wi (i = 1, 2, . . . n) in the neighbourhood of W, and estimating µw as a weighted average of the mean xi of the samples in Wi. Possible ways of grouping the samples are illustrated in Fig. 1 1.1. More complex patterns can be found in the literature (Krige, 1966) To calculate the kriging estimator of pw, we must be able to calculate the variance of xi, the covariance of xi and xj, and the covariance of xi and pµw. The purpose of this chapter is to show how these quantities can be calculated when we ignore the position of the samples in the block Wi. We consider the samples to be randomly distributed in Wi; kriging with this assumption is known as random kriging.

Jan 1, 1978

By D. Duncanson, R. J. Davidson

The elution of gold from activated carbon using deionized water by R. J. DAVIDSON, M.Sc., Ph.D. (Rhodes) (Visitor) and D. DUNCANSON, H.N.C., B.Sc. Hons. (Strathclyde) (Visitor) The pretreatment of gold-loaded activated carbon with a relatively strong sodium cyanide solution prior to elution with deionized water at 90 to 125°Chas been shown to have a most beneficial effect on the elution of gold. The findings emphasize the important role played by the calcium cation and the hydroxyl anion in effecting efficient elution of gold. The elution of the relatively unstable complexes of silver and base metals with cyanide was also significantly affected by the ratio of the sodium cyanide to sodium hydroxide in the reagents used in the pretreatment stage. It was demonstrated that the use of 0,5 bed volume of a pretreatment reagent comprising 10 per cent sodium cyanide stabilized with I per cent sodium hydroxide for safety reasons resulted in a virtually 100 per cent recovery of adsorbed gold, silver, and base metals on subsequent elution with deionized water. The elution procedure takes a relatively short time, about 14 hours at 90°C (7 bed volumes) or 3 hours if pressure elution at 125°C (4 to 5 bed volumes) is used. Because the mechanism of elution after pretreatment entails the shifting of a physical rather than a chemical equilibrium, the higher the gold loading on the activated carbon, the more efficient is the elution procedure. When compared with other elution procedures, the proposed method appears to have several economic advantages.

Jan 7, 1977

By J. Levin, I. J. Corrans

Wet high-intensity magnetic separation (WHIMS) for the concentration of gold and uranium was tested on many Witwatersrand cyanidation residues, and on some ores and flotation tailings. The results varied, but many indicated recoveries of over 60 per cent of the gold and uranium. The main source of loss is the inefficiency of WHIMS for material of smaller particle size than 20fLm. The recoveries in the continuous tests were lower than those in the batch tests. The continuous tests indicated an operational difficulty that could be experienced in practice, namely the tendency for wood chips and ferromagnetic particles to block the matrix of the separator. It was decided that a solution to the problem lies in the modification of the separator to allow continuous removal of the matrix for cleaning. A system has been developed for this purpose and is being demonstrated on a pilot-plant scale. Promising results were obtained in tests on a process that combines a coarse grind, gravity concentration, and WHIMS. In the gravity-concentration step, considerable recoveries, generally over SO per cent, of high-grade pyrite. were obtained, together with high recoveries of gold and moderate, but possibly important, recoveries of uranium. A simple model describing the operation of the WHIMS machine in terms of the operating parameters is described. This should reduce the amount of empirical test work required for the optimization of operating conditions and should provide a basis for scale-up calculations. The economics of the WHIMS process is discussed.

Jan 1, 1979

By I. E. Teymenson, N Fedunets

Mining-metallurgical complex is the base of any economics and influences directly on practically all branches of world economics. Therefore the task of estimation and selection of investment decisions in mining industry adequate to modern market conditions and the task of decreasing multidimensional alternatives selection uncertainty are very actual. An uncertainty of investment alternatives is explained by a number of reasons, main of which are a presence of several investors types, an unstable situation on the market and an absence of evident relations between appraisal criteria used. Maximum increasing of formalization and objectivity of information technologies applied for an estimation permits to reduce the uncertainty of investment variants estimation. A number of principled innovations, allowing to solve the task of decreasing of multidimensional alternatives selection uncertainty, are introduced into the information technology of estimating and selecting investment decisions in mining-metallurgical branch, developed by us. In the article the necessity of including a cognitive model into developed selection mechanism, which allows to take into consideration inter-influences of used critera, has been grounded. Besides, the forecasting model considering interconnected time rows has been applied for increasing the world conjuncture forecast quality. Further in the article main metrics types have been characterized and application of weighted Chebyshev’s metrics as the most compromised from all studied metrics for variants selecting has been proved, and also the developed procedure of directional search of effective compromise decisions has been described. Brief characteristic of designed instrumental means of multi-criteria variants estimation and selection finalizes the article. In conclusion expedience and efficiency of using the developed information technology for reduction of multidimensional alternatives selection uncertainty have been grounded.

Jan 1, 2003

By Lene Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pin point the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable emperature readings and gas analyses could have verified satisfactory activity, hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: Good record keeping is a necessity for collection of representative catalyst samples, reliable operating data is an inevitable starting point for all analysis and trending of operating data is a must for plant optimisation and troubleshooting. In addition these catalyst management tools will give a continuous updated knowledge of the catalyst status in each bed providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking of operating data, temperature optimisation and good record keeping.

Jan 1, 2009

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon's 'face element principle' to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By M. Keevy, K. Hackney

Centrifugal slurry pump station and deposition sites are a common feature of many mines and mineral processing plants. Yanacocha Mine has completed the design of a pump station consisting of two trains of four pumps each. A number of trade-off studies was conducted to optimize the pump station design. The most significant of these was determining the drive types for the slurry pumps. The pump station duty can vary considerably due to the number of deposition points round the disposal site. The standard solution to this problem on a multi-stage pump train is to install one pump with a variable speed drive to control the pump station output by varying the speed of this pump and stopping and starting other stages. However, there are a number of negative impacts associated with this approach. These include head losses through pumps that are stationary or ?wind-milling?, different wear life on pumps that are running and pumps that are stationary, and slower response to the control system with the possibility of hunting. The use of variable speed drives on all the pumps was considered as an alternative to the standard solution. The factors considered in comparing these options were the control and operational differences, the pump efficiencies and absorbed power, the expected pump wear life, the impact on pump maintenance and the cost of the drive options. For this project the option of using all variable speed drives was selected. The paper presents the following aspects of the study: ?Description of the various options investigated. This includes a discussion on the required duty and the drive options. ?Technical comparison between the options. ?Description of the factors influencing pump performance and life.

Jan 1, 2007

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012

When a mine decides to construct surface structures close to, or on undermined ground, it is required in terms of the regulations of the Mine Health and Safety Act to obtain permission from the Department of Minerals and Energy (DME). Apart from the legal requirements, the stability of the structures is crucial as damage to the structures due to surface movements could result in loss in life, equipment and/or production. This paper deals with the rock engineering aspects of a study that was conducted on one of the chrome mines in the Bushveld Complex (BC) involving the construction of plant structures on shallow undermined ground. The paper addresses the legal requirements and guidelines regarding ground stability of surface structures placed on undermined ground and the assessment of the undermined area with regard to the following: ?sources of potentially damaging surface movements ?safe mining spans ?stability of the pillars ?effect of the loading of plant structures on underground stability. Due to the irregular layout and geometry of the pillars in conjunction with a changing surface topography, numerical analysis and not the conventional tributary area theory was used to determine the imposed loads on the pillars. In order to subject the plant structures to minimum movement, the plant should be located in areas where the pillars would remain stable, the elastic deformation of the hanging wall is minimized and hanging wall failure extending to surface is unlikely to occur. The study indicates that although the depth of undermining is shallow (between 27 m and 60 m), potential damaging surface movements are not anticipated due to the stability of the pillars, competent nature of the overlying strata and negligible effect of the plant structure loading on the underground stability.

Jan 1, 2004

By G. Newson, N. Runciman

In 1999, INCO Limited Mines Research, in Sudbury, Ontario, Canada, took delivery of a MeycoRobojet Logica Spraymobile, a computerized concrete spraying system. The Spraymobile is a self-contained mobile machine capable of applying spray-on ground support in underground applications. The Logica component of the Robojet is designed to control the operation of the Robojet, as well as scan and map the tunnel geometry prior to the spraying operation. The Robojet can be operated in various modes, from manual to automatic operation. In the automatic mode the computer controls the standoff distance, angle, and motion of the spraying jet. In 2000, INCO Limited, working with Meyco Equipment of Switzerland (a division of MasterBuilders Technologies), detailed a plan to create a tele-operation package for controlling the spraying process from a surface location at INCO's Mines Research Test mine. With the RobojetLogica operating in automatic mode, the operator at the machine becomes a process monitor. Since the Logica system controls the key spraying parameters of nozzle distance and nozzle angle to the sprayed surface, the operator could easily monitor and control the Robojet Logica from aremote location. The benefits of operating underground mobile mining (drills and LHDs)equipment from a surface location has been demonstrated at INCO Limited, however, the abilityto control a ground support operation (shotcrete spraying) from surface has not been attempted until now. This paper will describe the Spraymobile shotcreting system, the development of the tele-operation package for the Robojet Logica, as well as modifications to the original Spraymobile for implementing the tele-remote package on the Robojet Logica at the Mines Research test mine.

Sep 1, 2001

By J. W. Oberholzer

The use of computers in the South African coal mining industry has increased during the 1980s. Applications at mine level commenced in the financial and personnel areas of payroll systems, mine accounting procedures and staff record keeping. More use is made now on mines of technical programs for purposes such as mine planning and mine survey calculations. The Coal Mining Laboratory of the Chamber of Mines Research Organization has provided, for a number of years, a service to Chamber member collieries in regard to the application of technical computer programs. Programs presently in use for simulating production procedures and conveyor belt transport systems are described. In addition, reference is made to the collection, storage and analysis of data concerning the performance of continuous miners over a period of eight years. More recently a computer program for the simulation of the cutting action of continuous miner cutting drums has been developed. The use of this program to assist with drum design is explained. The fact that many requests to make use of the programs are received from collieries is an indication of their acceptance by industry. Their interest in running the programs themselves on their own desktop computers has led to the need to convert the software for microcomputers.

Jan 1, 1987

By N. Brown

Australian mining companies are actively exploring for and developing mineral deposits throughout the world with interests in emerging markets such as Africa, Asia and South America. It is important to understand emerging market risk as this will affect the willingness of mining companies and financial institutions to invest in a country, especially with reference to their key asset, the mining licence or operating/concession agreement. Mining companies looking to develop new projects in emerging markets have different risk profiles than projects in countries such as Australia and Canada. Examples of key risks faced in emerging markets include: 1. political - expropriation, nationalisation, contract frustration, currency inconvertibility, war, terrorism, strikes, riots and civil commotion; and 2. legal - mining legislation, arbitration and dispute resolution, trade agreements. There is a problem in the difference in risk perceptions between mining companies, financial institutions and insurers. This can cause different stakeholders to carry out different evaluations of the risks faced by a project, resulting in confusion about the risk margin attached to any project. In a time where resource nationalisation and energy security are prompting governments to become more involved in the mining sector we run through some recent examples of mining companies that have had problems due to the key risks highlighted earlier. Importance of carrying out the right due diligence to replace perceptions with reality: ? early identification of risks - detailed due diligence on emerging market risks that may arise will help with their identification and mitigation, ? make use of companies that can help identify risks and suggest solutions, ? control the cost of financing - risk margin applied to a project ? finance loan will be influenced by the risks faced, and ? risk management and using political risk insurance. There are plenty of opportunities in emerging markets but it is important to recognise the associated risks. Detailed due diligence at an early stage will provide long-term benefits.

Jan 1, 2007

By M. Pelser, J. Hagemann

"The Anglo American Platinum Rustenburg Base Metals Refiners (RBMR) is the largest producer of nickel cathode in South Africa. It treats slow-cooled matte to recover a platinum group metal-containing magnetic fraction for downstream processing and a nonmagnetic fraction to produce nickel and copper cathode, cobalt sulphate, and sodium sulphate. The refinery was recently expanded from 21 to 33 kt/a nickel. During the ramp-up phase, the sulphur removal section was found to be a constraint to throughput. Nickel hydroxide is precipitated from nickel spent electrolyte by addition of sodium hydroxide, and filtration of the nickel precipitate allows sulphur to be removed from the circuit as aqueous sodium sulphate in the filtrate. The filtration fluxes were found to be limiting the circuit’s capacity. An obvious solution would have been to install additional filtration capacity at significant capital cost and long lead times. RBMR chose rather to first initiate a collaborative project with Anglo American Technical Solutions to better understand the impact of process conditions on filtration characteristics and to evaluate whether the filtration flux could be increased by improving the quality of the nickel precipitate.A deeper understanding of nickel hydroxide precipitation chemistry and kinetics in the context of high nickel and sodium hydroxide concentrations was developed, guided by precipitation theory and confirmed by laboratory tests and plant observations. It was found that the filtration rate could be significantly improved by modifying the precipitate characteristics. A new precipitation process was engineered and retrofitted into the existing plant. Since start-up of the new precipitation system, the available capacity of the sulphur removal section has more than doubled, and control of the process has improved with the better agitation. This paper describes the theory and results used to design the new agitation system, as well as the impact of the change on capital investment, operability, and process efficiency."

Jan 1, 2016