Search Documents

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By Donald Leroux, Simon Gariépy, Luc Lachance

"Quantitative information about the quality of metal balance results is often overlooked when making important plant production planning decisions. Not only is this common omission made in a context where many measurements taken in and around mineral processing plants carry significant errors, but it also conflicts with the AMIRA P754 Code of Practice for Metal Accounting. The fact that metal balances are typically published without any indication of data quality may give the wrong impression that the measurements are unquestionably accurate. While it is true that statistical data reconciliation can improve the confidence intervals of redundant variables, there is no data processing technique that brings them down to zero at a finite cost. In this paper, we review the entire data flow, starting from field instruments to metal accounting-based decision-making to show how measurement errors are transmuted into business risks associated with production planning. Necessary conditions for first exposing then quantifying such business risks are stated. Pitfalls to be avoided are also discussed. Finally, a simplified risk assessment and management procedure which considers the quality of metal balance results are applied to a polymetallic mineral processing plant. INTRODUCTION Each and every mineral processing plant has production reporting obligations. In this paper, we are concerned with metal accounting reports (Morrison, 2008) where saleable metal flows and inventories are estimated and published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimisation, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that spotless metal accounting is instrumental to high-quality corporate governance (Gaylard et al., 2014) of mining and metallurgical companies. To this extent, one would have expected industry-endorsed standards to have emerged a long time ago. However, the lack of an accepted set of standard procedures for metallurgical accounting was explicitly recognized as an industry-wide problem only in August 2001 during an SAIMM workshop held in Cape Town, South Africa. Discussions that followed this workshop led to the initiation of the AMIRA Project P754, “Metal Accounting and Reconciliation”, in 2003."

Jan 1, 2015

By A. J. Vietti

A pilot plant paste thickening campaign was conducted at the Anglo Platinum Limited Mogalakwena South Concentrator plant in South Africa in order to determine the water saving capability of P&TT technology. In the process a simple water consumption model was developed for estimating the overall water consumption of the mine. The model indicates that for the Mogalakwena tailings, significant water savings are achieved by discharging thickened tailing directly to the TSF but only at densities where free water release at the TSF is close to zero. Keywords Paste, thickened tailings, thickener, water savings, water consumption.

Jan 1, 2011

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

By L. R. Nelson

A review is presented of the furnace cooling system design and operating developments since the initial furnace start-up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators, in particular, to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement of operating this slag in a relatively highly superheated state (?T ?400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomization. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to HATCH high-intensity, water-cooled, copper Waffle coolers and tap blocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area), coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the HATCH Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By T. O. Hagan

Analyses of accident records show that a better understanding of very basic strata control principles and practices, by production personnel, will improve worker safety. Workers, lack of knowledge, with respect to aspects of strata control, increases their exposure to such strata control risks. The primary objective of the Safety in Mines Research Advisory Committee (SIMRAC) project 02 02 07 was to develop tools for the transfer of strata control knowledge. Four such tools were developed, three of which focused on illiterate underground mine team members who are not yet able to take advantage of the Mining Qualifications Authority (MQA) learning process (see project outcomes 2, 3 and 4 below). The tools were designed to equip these workers with sufficient knowledge and ability to work safely underground until such time as they can take advantage of the MQA system. Project outcomes: 1 A four-minute video using animation to illustrate the causes and prevention of falls of roof in South African collieries. 2 Software to demonstrate the capability of reconstructing, interactively, accident scenes and actions that have taken place underground in stopes. 3 A strata control bridging course for illiterate mine team workers. 4 Small-scale wooden models that will be used to design life-size mock-up facilities to assist with the above mentioned bridging course. 5 Workshops and presentations to demonstrate the outcomes 1to 4 above.

Jan 1, 2005

By G. L. Smith

This paper introduces and defines the concept of a linkage between long-term planning parameters (?global assumptions?) and possible future world views as conceived in scenario planning. Scenario planning, the tool that is used to arrive at plausible future worldviews, is described in the context of the platinum industry. The interpretation of the scenarios into long-term planning parameters is made, followed by an illustration of how the long-term planning process has been adapted at Anglo Platinum to include the notion of uncertainty.

Jan 1, 2008

By D. P. Penswick

The Palabora open pit is scheduled to cease operations in 2002. While the ore body continues below the bottom of the final pit shell, the stripping ratio precludes further economic open pit mining. Palabora Mining Company has investigated various means of continuing copper production, and has determined that an underground mine is the best solution. Board approval to commence construction of the mine has been granted and shaft sinking is underway. First production is planned for the year 2000 and full production of 30 000 t/d will be achieved by the end of the year 2002. [ ] Mechanised block caving will be the mining method employed at Palabora. The cave will be initiated by excavating a thin horizontal slice known as the undercut. Removal of the undercut will induce stresses which cause the rockmass overhead to fracture. Fractured rock will gravitate through drawbells to drawpoints on the production level, and be loaded by LHDs for transport to crushers.

Jan 1, 1997

By E. Snyders

The upgrading process of an inferior grade of zircon to a superior opacifier for ceramic applications was investigated. A calcining process in the presence of mineralizers was used to produce the product in a conventional muffle furnace. A pre-milled inferior grade zircon concentrate, with a relatively high iron and alumina content generally not suitable for high quality ceramic applications, was used in this study. The influence of the upgrading process on the opacifying properties of the zircon material was compared to that of commercially available prime grade zircon opacifier products currently being produced in South Africa. The influence of a calcining step in the presence of mineralizers with regard to the milling characteristics of the treated zircon material was also evaluated in this study. The morphology of the treated and untreated zircon opacifier samples were investigated by SEM micrographs and the colours of zircon samples were characterized on the grounds of the Commission Internationale de l`Eclairage (CIE) standard procedure (CIE L* a* b* measurements) after application on a bisque ceramic tile. It was found that the treatment improved both the milling as well as the opacifying properties of the treated inferior grade zircon concentrate and renders it equivalent to or better than prime grade zircon opacacifiers currently produced. Keywords: ZrSiO4; opacifier; colour; milling; calcining.

Jan 1, 2005

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By F. M. G. Egerton

Mechanisation of mining operations is not a new concept in the world of mining. Machinery has been developed, manufactured and used for many decades in massive orebodies and coal mines, both locally and abroad. Because of their size and the huge tonnages available, massive ore bodies lend themselves very easily to mechanisation. However, little progress in mechanisation has been made in narrow tabular orebodies in South Africa. The equipment available for narrow tabular orebodies requires excavations of a size that introduce large volumes of waste dilution. Nevertheless, it is essential for South African miners to experiment with mechanisation and to find a solution to the problem. This address looks at current conventional mining methods and compares them to bord-and-pillar type mining methods. Off-reef mechanisation is also touched on. It then looks at different hybridised mining methods that are being used, i.e. a mixture of conventional mining and mechanisation. It finally looks at future prospects for mechanisation in narrow tabular orebodies.

Jan 1, 2004

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By J. N. Van der Merwe

The principal goal of the research described in the paper was to determine, by measurement of pillar scaling on pillars that have not failed, whether the pillar life prediction method developed by van der Merwe (2003) was valid as it stood or whether adjustments were necessary to the rates indirectly derived from observation of failed pillars. To this end, measurements were taken on over 350 pillars at 13sites on 6 mines. The project was done as a collaborative effort between the University of Pretoria, the Nancy School of Mines and CSIR Miningtek. During the course of the investigation, it was found that the majority of pillars display maximum scaling at mid height, that there was no clear preferential direction of pillar scaling, and that pillar corners do not scale significantly more than the mid pillar areas. The most important conclusion was that the scaling rates found by measurement agreed with the inferred rates found in the previous work. The previously developed procedure for the prediction of pillar life spans consequently requires no adjustment, although the error span is in the region of 20%. It is recommended to do further research into the effect of sealing of panels and, possible chemical changes taking place in the pillars as they age on the scaling rate.

Jan 1, 2004

By R Kroukamp

Horizontal belt filters are typically used for separation of relatively free filtering solids where good post treatment is required. He horizontal belt filter is a continuous filter with an endless cloth supported on a grooved carrier belt. The belt and cloth are driven around two rollers across a series of evacuated suction boxes. The feed suspension is introduced at one end of the filter and deliquored to produce a cake at the other end. The benefits of using horizontal belt filters are good cake washing, continuous and visible processing, fully automatic operation, flexibility, high capacity and relative high speeds of operation. If required, horizontal belt filters enable efficient counter-current washings to minimize the usage of wash liquid. The horizontal belt filter has applications in the following: [? Metal concentrates ? Mineral sands ? Tailings ? Coal ? Iron ore ? Alumina ? Chloride processing ? Nickel and Cobalt refining ? Platinum group metals ? Zinc processing ? Many other applications in the Mining and Metallurgy industries ] 2. Operating Principle of a Horizontal Vacuum Belt Filter 2.1 Cake Forming The slurry to be dewatered is evenly distributed onto the filtering surface. Gravity assists the cake formation and the feed can be introduced in multiple stages. 2.2 Cake Washing Once the cake is formed, wash liquor/water can be introduced onto the top of the cake via a wash launder or sprays. Multiple wash stages, co-current, counter-current or direct washing can be added by increasing the length of the filter.

Jan 1, 2007

By K. M. Phamotse, A. S. Nhleko

"*Paper written on project work carried out in partial fulfilment of BSc (Mining Engineering) degreeSynopsisLiqhobong Mining Development Company (LMDC) has been experiencing problems with boulders after blasting where the fragment sizes exceed the maximum of 800 mm as per mine standard. As a result, the mine has employed various methods to improve the fragmentation. The goal is to produce a run-of-mine (ROM) feed that does not choke the crusher and cause delays in production. In order to achieve this goal, fragmentation distribution within the fines and coarse envelope must be optimized through effective planning of blasting activities and accurate execution.The mine determined the fines-coarse envelope within which the entire crushing system can handle fragments using Split Desktop software. It is expected that both the predicted and actual fragmentation curves lie within that envelope for optimal fragmentation. The Kuz-Ram model with blast design parameters of 2.6 m for burden, 2.8 m for spacing, and 127 mm hole diameter was used to predict the fragmentation. The results show that the blast design parameters may need altering to achieve optimum fragmentation. Furthermore, the execution of the drilling and blasting may be the cause of the fragmentation problems. The mean fragmentation size (X50) differs greatly, unlike the uniformity index (n)s values which are relatively close to each other (0.6 to 2.2). The mean squared error (MSE) values have a large range. A proposed solution is a modified burden, spacing, and hole diameter. It is concluded that blast design parameters need to be reviewed in order to obtain correct predictions. IntroductionFragmentation has an impact on the mine production cycle which comprises, inter alia, drilling, blasting, loading, hauling, and crushing. Correct fragmentation as set by the plant design is important as it reduces the time lost due to secondary blasting and/or loading difficulties. In this paper we analyse blast results at Liqhobong Mining Development Company (LMDC) in Lesotho for a period of six months. This project was undertaken to observe the trends from the blasts and to identify whether any discrepancies exist in the overall blast information. The period under study included 16 blasts."

Jul 1, 2019

By T. Saito, S. Murata

An original concept of JRC-diagram that can evaluate JRC and its size-effect by using a fractal model was proposed. In order to confirm the applicability of the JRC-diagram, first, JRC of the tensile fracture surfaces of a granite and a sandstone were evaluated by both the JRC-diagram and Barton's JRC-profiles, and then, it was compared with the JRC inversely calculated from the peak shear strength that is obtained from the shear test for each fracture using Barton's empirical equation. As a result, JRC evaluated by the JRC-profiles was much smaller than the inversely calculated JRC. On the other hand, it became clear that JRC evaluated by the JRC-diagram is almost the same with the inversely calculated JRC, if the size of interlocking is evaluated correctly. Therefore, for the JRC evaluation, it is thought that the JRC-diagram is more applicable than the JRC-profiles. Als ein neues Verfahren zur Bewertung des Rauheitsindexes JRC für die Bruchfläche von Felsenschichten anhand eines fraktalen Modells, wobei auch der Maßeffekt berücksichtigt wird, wird ein JRC-Diagramm vorgeschlagen. Um die Angemessenheit der Bewertung vom JRC mit diesem JRC-Diagramm festzustellen, wurden die JRC-Werte an einer Bruchfläche zwischen Granit und Sandstein sowohl mit dem JRC-Diagramm als auch mit dem herkömmlichen JRC-Profilverfahren bewertet. Anschließend wurden die durch die beiden Verfahren ermittelten Werten mit den JRC-Werten verglichen, die von den Schertestergebnissen mit Hilfe von Bartonschen Erfahrungsformel zurückgerechnet werden können. Daraus ergab sich, daß das JRC-Profilverfahren ziemlich kleinere JRC-Werte gibt als bei der Zurückrechnung, während die JRC-Werte durch das JRC-Diagramm unter entsprechender Bewertung des Ineinandergreifungsmaßes an der Bruchfläche beinahe gleich sind wie die zurückgerechneten Werte. Diese Tatsache weist darauf hin, daß das JRC-Diagramm eine bessere JRC-Bewertungsmethode als das JRC-Profilverfahren darstellt. Nous avons proposé le diagramme JRC, nouvelle méthode d'évaluer JRC qui est un indice de rugosité superficielle d'une fracture de roche à l'aide du modèle de fracturation, compte tenu de son effet d'échelle. Pour vérifier la validité de JRC évalué au moyen de ce diagramme, nous avons évalué JRC d'une fracture de roche, granite et grès, par le diagramme JRC et le profil JRC, méthode conventionnelle, et les résultats ainsi obtenus ont été comparés avec la valeur de JRC calculée en sens inverse à l'aide de la formule empirique Barton sur la base des résultats de l'essai de cisaillement des fractures. Il en résulte que la valeur de JRC obtenue par le profil JRC était assez faible en comparaison avec la valeur calculée en sens inverse alors que celle de JRC obtenue par le diagramme JRC correspondait approximativement à la valeur calculée en sens inverse à condition d'évaluer l'échelle d'endentement d'une fracture. Par conséquent, nous considérons que le diagramme JRC est une meilleure méthode d'évaluation de JRC par rapport au profil JRC.

Jan 1, 2003

Power Point Presentation

Jan 1, 2007

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015