Search Documents

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By G. A. Munoz, J. D. Miller

Gold leaching of an auriferous pyrite ore from the Portovelo deposit in Ecuador indicates that noncyanide leaching systems, such as thiocyanate and thiourea, are not as effective as the traditional cyanide system. For example, whereas approximately 95% of the gold can be leached from the ore with cyanide, only about 50% gold dissolution can be achieved with a thiocyanate leaching system. Electrochemical measurements indicate that gold is not cathodically protected by pyrite in these systems. Based on the results of preliminary diagnostic experiments, it appears that gold dissolution in thiocyanate and thiourea systems is limited by passivation due to the formation of either elemental sulfur or sulfur compounds on the gold surface.

Jan 1, 2000

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By Edward R. Borcherdt

When one considers the advancements made during the 25 years prior to the late fifties, and compares these advances with the progress made in the past decade, the comparison is indeed startling. It was not until 1935 that trucks began to replace rail as a major hauling facility, Initially, the haulage capacity of end dump trucks was limited to 18 or 20 tons. "Straight stick" transmissions were utilized and the available horsepower was minimal. In the early forties single planetary axle 25 ton trucks were introduced, and shortly thereafter those were followed by 35 ton tandem axle units.

Jan 1, 1967

By F. M. Swain

High-calcium limestones occur in the upper part of the New Market Formation, of Lower Middle Ordovician age, in Franklin and Cumberland Counties, Pennsylvania. The high-calcium facies of the New Market Formation is represented by sublithographic limestone or vaughanite, which probably formed in quiet water; low-energy environments such as intershoal lagoons, or in protected bays similar to the present-day Florida Bay environment. Rapid facies changes are characteristic of the strata. The better grade of stone lies in the upper 100 to 125 feet of the New Market Formation and averages 95-97% calcium carbonate. Silica and magnesia are about equal in amount as impurities. One high-calcium belt extends from the Maryland state line through Chambersburg and Newville to beyond Carlisle. The strata in this belt are structurally complex, which requires careful field study' and core-drilling prior to exploitation. Stone suitable for blast-furnace flux is present in relatively large amounts, but stone for open-hearth use or portland cement requires more selective quarrying.

Jan 1, 1966

By E. H. Cho, P. K. Dai

An acid mine drainage sludge sample, containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn, was obtained from central West Virginia. The sample was leached at room temperature with a pH 3 sulfuric acid solution. Air was then bubbled through the leach solution at pH 4.5 to precipitate the iron. The leach solution contained 258 ppm Zn, 105 ppm Ni, 90 ppm Co and 2050 ppm Mn. Three solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA. Cyanex 272 and Lix 84. The A/O ratio was one, and the extractants were diluted ten times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to a pH of 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions should be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1995

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

Jan 1, 2004

Building aggregates, basic materials for the construction industry, must be produced according to socio-economic and environmental sustainability principles, i.e. the three fundamental components of Sustainable Development. On this subject, an introductory discussion about the interpretation of these concepts in the field of mineral production and construction industry is first presented. As for the socio-economic aspect, aggregates are then illustrated as being essential resources for the development of the society, underlying that it is possible to understand their fundamental socio-economic role only through the analysis of the whole product life cycle, from production to end use and beyond. The same has to be done on the environmental side to assess the environmental impacts of aggregates: one should look for, not in the quarry phase only, but also in all the downstream activities of the construction process, including the use phase and beyond. Based on this approach, in the second part of the paper, the results of some investigations focused on eco-profiles of building aggregates, gathered through the application of LCA methodology are presented and discussed. In such a context, strengths and weaknesses of LCA indicators will be discussed, as well.

Jan 1, 2007

By Wilhelm J. Kogelmann

The quest for U.S. energy independence will result in a major increase in underground mining operations. It will necessitate the rapid excavation of development drifts, entries and slopes to exploit underground deposits of energy resources such as coal, uranium and oil shale. Most of this development work will be done in soft and medium hard rock up to an unconfined compressive strength of approximately 20, 000 psi. OBSTACLES TO RAPID TUNNEL EXCAVATION Labor In the U. S. coal mining industry, the underground productivity in tons per man-day declined from 15. 61 in 1969 to 11. 00 in 1973 which is a startling 30% decline. While productivity declines, the cost of labor and supplies continues to rise. Ralph E. Bailey of Consolidation Coal Company recently stated four reasons for the decline of productivity: A shortage of experienced miners, enactment of the Federal Coal Mine Health and Safety Act effective April 1970, major changes in union work rules in 1968, and a deterioration in the attitude of the work force (1). Because there is already a great shortage of skilled miners, the situation will get worse when large new mines for oil shale, coal and uranium open in sparsely populated areas in the Western United States. Only the large scale use of easy to operate tunneling machines can increase productivity and lower the cost of excavation.

Jan 1, 1974

By G. D. Hood, C. E. Jordan

The US Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67% copper and with a phosphate-bearing amine flotation tailings sample containing 9.5% P2O5 in a quartz matrix. Over 88% of the copper was recovered from the ore in a rougher concentrate containing 5.9% copper at a rate seven times, faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate four times faster than conventional flotation. The unfloated product retained 80% of the phosphate in a 16.9% P2O5 concentrate.

Jan 1, 1994

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By K. J. Stratford

The selection of a suitable mathematical function for the modelling of the partition curve for dense medium cyclones is discussed. Five alternative functional forms (based on three basic functions) are compared using data obtained in the course of an extensive experimental study of a 610mm dense medium cyclone. It is shown that, for adequately sampled tests, any of the functions may be used, although a function based on the Weibull distribution is shown to be most suitable. Where data are poor, all functional forms exhibit disadvantages, notably in terms of a reduction in precision of parameter estimation. This problem can be exacerbated by the complex numerical techniques required to estimate the parameters of a particular function. A set of ideal requirements for a performance function are presented.

Jan 1, 1986

By Thomas C. Wilder, Firoze E. Katrak

As part of a survey on the long range supply of gallium, a comprehensive review of the chemistry of commercial gallium extraction was undertaken Owing to its very small concentration in all commercial minerals, gallium can be produced economically only as a by-product of major extraction processes for other materials. A summary is presented for the chemistry of gallium extraction from many of these process streams included are several procedures for gallium recovery from bauxite, currently the most prevalent source Other processes described are from waste streams from the production of zinc, phosphorus from phosphates, aluminum from kaolin clays, and from coal ash, the largest potential resource A brief review of development of solvent extraction as a unit process for gallium recovery is also presented

Jan 1, 1983

By J. W. Wilson, Y. P. Wang, M. H. Erten

The use of water is still the most effective and economical means for dust control in underground coal mines today along with dilution by the ventilation current. Studies have shown that the dust capturing capacity of water is a result of a balance of many intermolecular forces. Surfactants are known to reduce such forces by affecting both the surface tension of the liquid and its interfacial tension against a solid. Surfactants can be added to the water sprays to facilitate the dust capturing capacity. A laboratory scale model has been developed in which surfactants were added to the spraying water and preliminary data indicates positive results.

Jan 1, 1991

By J. A. King, D. R. Weir, P. C. Robinson

Preconcentration of Porgera ore results in high recoveries of gold into gravity and flotation concentrates. The bulk of the gold is contained in auriferous pyrite flotation concentrate and is not readily recoverable by direct cyanidation. Oxidation in autoclaves at high pressure and temperature produces a residue that contains the gold in recoverable form. Pilot plant treatment of the autoclave residue is described, through washing and jarosite decomposition stages, to cyanide leaching and recovery of gold and silver by carbon-in-pulp techniques. The concern associated with disposal of plant effluents are also addressed.

Jan 1, 1987

By Z. C. Liu, F. F. Roxborough, Lin. B. B.

The size distribution of coal cut by a mining machine is an important performance factor. It is well established that the main machine system variable that affects product size is the depth of cut. In essence, the greater the amount of coal won by a machine cutting at shallow depths, the greater the proportion of dust and fines produced. Conversely, deep cuts produce less dust and a generally larger product size. When cutting with a rotating drum, as well as with a longwall shearer, the depth of cut always varies from zero in the vicinity of the roof and floor, where most of the dust and fines are produced, to a maximum at mid-drum level. In this paper, minimizing the amount of shallow cutting with a cutting drum is discussed, and the effects of the drum cutting and design parameters on cross-sectional cutting area per revolution are analyzed. This study shows the following: •more shallow cutting occurs during the entry quadrant of a cutting cycle than during pick exit; •the ratio of the projected area of shallow cutting to the total projected area of cutting by a single pick per drum revolution is virtually the same for drums of different radii (however, it decreases as the maximum depth of cut increases); and •for double drums, the use of unequal drum diameters can reduce the production of dust and fines, compared to using drums of the same diameter.

Jan 1, 1998

By S. Page, R. Bhaskar

The development is described of a real-time tracer gas sensing system for use in fell-scale laboratory studies of air flow behavior around mining machines. A semiconductor sintered tin-dioxide gas sensor is used for gas analyses. A data acquisition and analyses software specific to the sensor characteristics was also developed as part of the system. The system permits the study of transient behavior and assists in obtaining a better understanding of the movement of air around mining machines and in the study of the effect of potential airflow modification devices on the dust exposure of face personnel. It seeks to replace the current method of using a centralized infrared gas analyzer that polls several sampling points using an array of solenoid valves and gas line purgers. The polling results in a significant time lapse between the first and the last set of readings. The system described in this paper has the advantages of real-time sampling and safe operation.

Jan 1, 1992

Computer applications in mine 'production' planning and control are concerned with the here and now. In production planning and control we are dealing with tactics as opposed to strategy. Our objective is to make the best of the situation in the short term, i.e., in a relatively fixed environment with relatively fixed plant, equipment, and labor. Environmental factors include not only the geology of the deposit but also market factors (such as price) and governmental constraints and regulations. Mine production planning systems are applied at the interface between concept and execution. Mine production control systems are applied at the interface between execution and revised operating practices or a revised concept. Fig. 1 shows the information flow that takes place regardless of whether the planning and control systems are manual or automatic. The feedback that results depends on the feedback mechanism that has been established, and this feedback can be enhanced by careful systems analysis and design. Chronologically, production planning and control activities support the last in the series of line functions that are ordinarily performed by mining companies. The first of these is exploration, the second is evaluation and development, and the third and final function is production.

Jan 1, 1979

By R. Poulin, A. Lamontagne, N. Tassé

This paper presents the results of a laboratory investigation aiming to verify the concept of co-mingling of waste rock with layers of compacted tailings. Overall, co-mingling is expected to delay the onset and reduce the magnitude of acid mine drainage (AMD) production in waste rock. To denionstrate the efficiency of the method proposed, five different column tests have been set-up. Columns were fed with deionized water at the top and drainage waters were collected and analyzed. Bacteria counts were done on the tailings and waste rock after the column tests. Permeability in saturated conditions and capillary parameters were measured for the tailings. The results obtained show that the co-mingling method would be effective in mitigating AMD by maintaining nearly water-saturated conditions in compacted tailings, thus reducing oxygen supply in waste rock by preventing thermal air convection and minimizing oxygen advection and diffusion.

Jan 1, 2000

By D. D. Snyder, J. D. Bode, F. T. King

INTRODUCTION Only in recent years have the environmental hazards associated with mining and tunneling operations been fully acknowledged and determined remedial action undertaken. The nature of these excavation operations leads to a wide diversity of hazards spanning mechanical, electrical, chemical, environmental, and physiological. The most insidious of these are unquestionably the environmental ones which have the greatest long-term effect and are the most difficult to pinpoint and monitor. It is the atmospheric contaminants that lead to a significantly greater illness and mortality rate among miners. Dust is the most prevalent, hence most important of the atmospheric contaminants. Respirable particles lead to diseases characteristic of many mining operations: coal workers pneumoconiosis, asbestiosis, silicosis, talcosis, anthrocosis, etc. But toxic and suffocating gases can be equally insidious and the most innocuous pollutant, methane, leads to the most imminently disastrous results of all - explosion and fire. This means that truly effective monitoring of the environmental hazards in tunneling cannot be limited to a few simple standard check measurements. It must include the most precise measurements we can make for specific, documented hazards and even for factors, such as noise and heat stress, not immediately obvious as hazards. The Federal Metal and Nonmetallic Mine Safety Act and more recent Occupational Safety and Health Administration standards are clearly designed to match such effective monitoring. We must, therefore, consider not only presently available monitoring instruments and those currently under develop-

Jan 1, 1997