Search Documents

By K. J. Stanaway

Syngenetic concentrations in clastic sediments of valuable mineral particles with specific gravities exceeding that of quartz constitute placer deposits. Two fundamentally different modes of concentration characterize "trap" and "bed" placer variants. Trap placers originate during sediment erosion or reworking. Bed placers form during episodes of sediment accumulation in a variety of depositional environments and lithofacies where mineral supply and fluid dynamics are favorable. Because trap placers are thin and generally limited in area, they rarely yield economic heavy-mineral deposits. They can become economically significant if they contain more valuable "heavies," such as gold, or if they occur within or very close to much larger but characteristically lower-grade bed placers.

Jan 1, 1993

By R. J. Sweigard, R. V. Ramani

Estimated costs and revenues can be used in evaluating postmining land use alternatives. However, postmining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact on each alternative under consideration. In this paper, a method is presented that employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1988

By Drupad B. Desai

Baltimore Region Rapid Transit System project final design began in 1973. The Section A of the planned Phase I is scheduled to go into revenue service in late 1982. The subway line structures include earth tunnels, rock tunnels and cut-and-cover structures. Final designs were performed by both the DMJM/KE staff and by outside subconsultants. This paper deals with Section A of the program. (Fig. 1.) The overall program cost for Section A is estimated to be $721 million. The cost for construction and owner furnished equipment is estimated to be $600 million, including contingency and escalation to time of construction. The remaining amounts are for right-of-way, design, construction management and agency (MTA) costs. The Section A line structures, including station lengths, are divided as shown in Table 1. [ ]

Jan 1, 1979

By J. S. Stachulak

Installation of a computerized mine monitoring and control system in two planned construction phases began in 1983. Phase one consisted of providing a central monitoring station located on surface for monitoring underground CO detection in Frood Mine's heated area. The implementation of this project annualized labour savings of $200,000. The cost of installation of an early fire warning system was $100,000. There are several CO sensor monitoring carbon monoxide trends through mine heated areas. To obtain an early warning, it is not good enough to know that a fire has started, but it is also necessary to know where the fire is located.

Jan 1, 1989

By J. M. Kruger, P. Berendsen, A. Martinez

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1998

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By Kal V. S. Sastry

Mathematical and expert system models are being used extensively for mineral process engineering. There exist no standardized methodologies for their computer implementation. In meeting this need, this paper introduces the concept of a process software model, or simply a software model and presents a two-step methodology for its development involving software model specification and development. The software model specification is to be performed after extensive discussions with the ultimate users of process software based on which the software model is developed. These software models provide a formal basis for the design and construction of software objects corresponding to the real world process objects.

Jan 1, 1994

By L. Boyd, T. Martin, V. Gall

Water infiltration into subgrade infrastructure can cause major impacts on their performance. In addition to damaging the structure, water intrusion leads to deterioration of installations including electrical and mechanical components and in patron discomfort. To remedy these impacts, leak remediation is often carried out to halt water infiltration. Remediation methods include coatings, drainage, injection/stitch grouting, curtain (backside) grouting, and/or internal umbrella systems. Selection of the rehabilitation method depends on the structure’s use, owners’ priorities, its installations, structural conditions, surrounding ground, and hydrogeologic conditions. Since many factors influence the rehabilitation method chosen, a novel holistic approach is undertaken to understand leakage causes and consequences to develop the most appropriate, efficient, and reliable solution to extend the structure’s life. A reconnaissance phase combines geologic, hydrogeologic, and as-built information with detailed digital scans and visual observations to develop a database of existing conditions. This database, called a tunnelband, is used to develop the rehabilitation solution and made part of the contract documents, allowing for an informed bid by specialty contractors. Tunnelband and the preferred rehabilitation system are portrayed in contract documents, which are procured in various contract types depending on the owner’s preference and project characteristics. The pool of contractors are required to submit their understanding of this holistic approach by developing and supplying the owner with a detailed workplan. The completed rehabilitation is portrayed in detailed as-built drawings which also provide the owner with an operation and maintenance manual outlining for periodic observation of the structure and checking of its performance. Ultimately, this information is implemented into a “BIM Digital Twin” that is used by the operations and maintenance staff for long-term observations. This proposed novel framework for leak rehabilitation is currently being used successfully in a number of projects throughout the United States.

Jun 13, 2023

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By P. T. Brown

Denison Mines Limited, Canada's largest uranium producer located in Northern Ontario recently embarked upon an extensive development program that would allow them to substantially increase production and also meet the more stringent air quality standards established by the ministry of Natural Resources. To proceed with this program it was essential that the fresh air supply be greatly increased to the underground workings. A major portion of the mining area is located under Quirke Lake on the north limb of a syncline termed the Quirke Lake trough. The Denison engineers determined the most practical size and location for a proposed new fresh air shaft, eventually deciding to drive a 25 foot diameter shaft, 490 square feet in section for 1,800 feet long vertically. The shaft collar would be located on Roman Island, an island in Quirke Lake. A test hole was drilled from Roman Island to determine the ground through which the ventilation shaft would pass. This drill hole confirmed the location of the Quirke Lake over-thrust fault, a highly fractured water bearing zone 165 feet thick, approximately 800 feet below surface. Plans were made by Denison Mines Limited to seal and consolidate this ground when it was encountered by the shaft.

Jan 1, 1974

By Marian W. Otrebski, Julian A. Korneck

Long distance, overland conveyors require significant capital outlay of which up to 70% may be contributed to the cost of belting. Significant savings may be achieved by identifying possible risk areas and applying modern technology methods to reduce or eliminate risk. Recently, Sasol Coal commissioned an overland belt conveyor system comprising three belt conveyors of 7 km, 5 km and 4.5 km in length. These were designed and constructed taking the above into consideration. Contained in the paper are the belt conveyor system requirements, designing assumptions and methods applied in the designing process as well as ways and means to eliminate or at least reduce risks.

Jan 1, 1998

By C. J. Kirkland

HISTORICAL BACKGROUND For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water which seperates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peacable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic. A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British Parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1987

By J. J. Carlson

Studies were carried out to determine whether filtration rate changes observed in an iron ore concentrator were due to variations in particle shape. It was confirmed that ores mined from different locations differed in filtration rates by as much as 60%. However, when image analysis was used to quantify the shapes of the individual particles in the filtration feed, it was found that the particle shapes showed almost no variation, and the shapes did not correlate with the filtration rate. It was also determined that the filtration rate variations were not caused by changes in particle size distribution. These results suggest that the differences in filtration rate are due to factors other than size and shape, such as surface chemistry.

Jan 1, 2008

By Eugene F. Casey

The next ten to fifteen years will be exciting ones for the construction industry because three city agencies alone have started or will start, on tremendous expansion programs, the cost of which will exceed a total of four billion dollars. The major portion of this work will be done by the use of tunnelling methods. *Tunnelling is construction by any method of a covered cavity of predesigned geometry whose final location and use under the surface, whose cross-sectional area is greater than two sq. meters. The New York City Transit Authority's expansion program will provide for approximately 52 miles of new subways. The Board of Water Supply has already started on City Tunnel No. 3 which, when completed will provide the City with enough water until the year 2000, and the Board of Water Resources has embarked on a tremendous program to clean up the surrounding waters. Yes, these will be exciting years, particularly when one reads about the new novel exotic methods of rock breaking and disintegration, coupled with the new methods of soft ground tunnelling.

Jan 1, 1997

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By Richard V. Beck, Donald R. East, Jeremy P. Haile

In view of the increasing use of heap leach operations in the mining industry and the critically important performance of the leach pad liner in both the economic and environmental aspects of the design, it has become essential that the designer fully understand the factors affecting the performance of the liner. Minimizing the loss of pregnant solution through the leach pad liner is obviously of paramount importance to the economic efficiency and environmental compliance of the heap leach operation. Losses through the liner are a function of the hydraulic conductivity of the liner material and the hydraulic gradient across the liner. This applies to both natural and synthetic materials. The hydraulic gradient across the liner is a function of the build-up of solution above the liner, which in turn is determined by the permeability of the heap material, the slope of the liner, the drainage path length and the leachate infiltration rate. A relationship incorporating each of these parameters and their effect on the hydraulic head acting on the liner has been developed in terms of the Dupuit criterion, assuming one- dimensional flow with vertical accretion.

Jan 1, 1987

By K. A. Natarajan

This paper deals with the various electro- and biochemical mechanisms involved in the bioleaching of multisulfide minerals such as those containing copper-lead-zinc and copper-nickel-iron. Galvanic series for sulfide minerals consisting of pyrite, chalcopyrite, galena, sphalerite, pentlundite, and pyrrhotite in an acid bacterial leaching system is illustrated, and the role of relative electrochemical activity on selective dissolution is discussed. Typical leaching results are shown to illustrate the practical applicability of galvanic effects in bioleaching of multisulfides. Attachment of Thiobacillus fewooxidans onto chalcopyrite and sphalerite mineral substrates is illustrated through scanning electron micrographs. The role of high-metal-tolerant, specially adapted strains in the leaching of multimetal concentrates is also outlined.

Jan 1, 1987

By J. Kemeny, B. Norton, T. W. BoBo

Digital image analysis systems to quantify particle size of crushed materials have successfully been applied in large-scale mining operations throughout the world. Particle size measurement at various crushing and sieving stages, especially in aggregate production, will facilitate the industry’s desire and need to achieve higher levels of process control and automation. This paper will 1) summarize applications of digital image analysis in the industrial minerals industries and introduce the Split-Online technology; 2) detail an actual recent test application of digital image analysis that ultimately lead to the installation of an automatic, non-invasive particle size distribution monitoring system; 3) document how this information is being applied: and 4) summarize the new Split-Online Aggregates Module now available.

Jan 1, 2004

By Mike L. Aziz, Keith D. Ferguson, Glenda Ferris

The Equity Silver mine has been a severe producer of Acid Rock Drainage (ARD) since 1982. The mine was closed in 1994 and a compacted clay cover installed, but ARD continues to be produced. Three permanent employees manage the collection and treatment system at the site. The site still poses a significant environmental risk to the environment and downstream users and requires a high level of diligence. Various stakeholders' perspectives of the risk posed by Equity, and what constitutes acceptable risk, will be examined in this paper from a company operation staff, corporate environmental manager and downstream environmentalist perspective.

Jan 1, 2000