Search Documents

By F. Djahanguiri

The US Bureau of Mines con¬ducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1997

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981

By P. D. Rao, D. E. Walsh, W. W. McClintock

A column flotation system was designed to conduct release analyses on a very finely disseminated, stratiform copper ore from the Denali Copper Prospect in Alaska. Chalcopyrite is finely disseminated in a carbonate matrix, and pyrite is disseminated in both the chalcopyrite and the gangue. Grinding to -20 µm is required for adequate liberation. A 25-mm x 2.4-m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate. The rougher concentrate was then repeatedly floated to produce release fractions. These fractions were analyzed for copper, iron, calcium and magnesium, and release curves were plotted. The procedure was replicated at each of two grinds, i.e., 99% and 88% passing 37 µm (400 mesh). The procedure should find application for flotation characterization and process selection. Bond grindability testing was also conducted.

Jan 1, 1996

By Gary Buchan

During several months in 1996 and 1997, Cyprus Twentymile Coal Co. (TCC) set world production records at its Twentymile Mine in northwestern Colorado. These records were due to the company's implementation of a state-of-the-art longwall mining and conveyance system along with a -highly dedicated work force. This article is a case study of the design of long panels at the mine from conception to implementation. Obstacles that needed to be overcome included subsidence engineering, environmental regulations, conveyance, ventilation, equipment design and continuous miner (CM) development timing.

Jan 1, 1998

By A. A. Peshkov, N. A. Matsko, K. N. Trubetskoy

It is possible to divide the general objectives of a company into two components: maximum expected profits and viability over time. These components are designed to maximize the companies value over time. The evaluation of a project includes both a discounted cash flow (DCF) analysis and a risk analysis. The DCF analysis determines whether the project should be accepted or rejected, and the risk analysis helps to forecast possible deviations from the original estimates. However, the results of both methods do not allow for a quantitative comparison between the main objectives of the venture, and they do not resolve the issue of whether it is advisable to sacrifice immediate profits for future profits. This paper attempts to resolve this issue. The present research was carried out on mining projects with different waste-extraction schedules. Calculations were made using the US Bureau of Mines' usage-of-costs model. Russian experience in open-pit mining is reflected in this paper.

Jan 1, 1996

The processing capability of a semi-autogenous (SAG) mill is greatly affected by ore geology and operating variables within the mill. The SAG mill is problematic because it cannot be conveniently studied on a smaller, laboratory-scale mill. The interior of the mill, where grinding takes place, cannot be observed using instrumentation available today. Yet the motion of the rock and ball charge determines the power draft and hence capacity of the mill. Therefore, mill optimization is pursued with a charge motion simulation software. This software uses the discrete element method to describe the individual motion of numerous ball and rock particles in the mill. It is shown that by simply increasing the chord length between the lifters and increasing the face angle of the lifters the capacity of the mill can be increased. Such a configuration of lifters allows the operator to increase mill speed, hence drawing higher power while considerably minimizing direct ball strikes against shell plates and lifters. A case study of a 36 ft. diameter x 15 ft. long mill is presented. Reducing the direct ball strikes leads to lesser steel consumption both in terms of balls and lifters.

Jan 1, 2000

[Costs may be classified according to their source and behavior: Scale of aggregation - Total costs - Unit costs Time period for which the costs are charged - Product costs - Period costs Controllability and relevance for decision-making and control - Controllable costs - Noncontrollable costs - Sunkcosts - Opportunity costs Their basic source - Production costs (also termed manufacturing costs) - Nonproduction costs How the costs change with changes in activity - Fixed costs - Variable costs - Semivariable costs Traceability to individual units of production - Direct costs - Indirect costs Use in planning (budgeting) and subsequent control - Standard costs - Normal costs ]

Jan 1, 1999

By J. A. Herbst, K. N. Han, P. B. Queneau, S. W. Asihene

As hydrometallurgy matures as a technology, more of its existing process knowledge will continue to be summarized in the form of detailed mathematical models. This development is happening at a time when major improvements in computer hardware have reduced the cost of computing. The opportunity then exists, through the solution of these process models, to design, control, and optimize hydrometallurgical plants on the basis of the physics and chemistry of its processes and less on empiricism. In this paper, a review of the current capabilities of sensors and phenomenological models for selected hydrometallurgical processes is presented. Future trends, in terms of the control and optimization of hydrometallurgical plants, are then explored. The possibility of simultaneously optimizing plant design and associated process control system performance is discussed.

Jan 1, 1993

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and use a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow controlling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1990

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987

By B. J. Arnold, F. F. Aplan, R. R. Klimpel, E. C. Jr. Dowling

Residence-time distribution techniques are useful tools in the analysis, characterization and modeling of the performance of processing equipment and circuits. This paper presents the results of both conventional and more-sophisticated residence-time distribution techniques for industrial copper-flotation-circuit data. While conventional techniques provide a description that is sufficient for macroengineering design requirements, the more sophisticated tracer-technique methods give more realistic descriptions of process flows and system effectiveness. It is demonstrated that these approaches can provide highly useful information about different equipment, as well as its configuration and performance.

Jan 1, 2000

By Fred Leighton

INTRODUCTION Dynamic (seismic or microseismic) methods of determining the stability of structures in rock are based on detecting and analyzing the characteristics of seismic energy that has originated from or traveled through the rock mass. This seismic energy can be in the form of naturally occurring rock noise energy resulting from structural adjustments within the rock or can be introduced into the structure by physical means, such as by blasting or impact. In either case, the seismic energy radiating through the rock mass can be detected using standard equipment and can be analyzed by established techniques to reveal a wide variety of information concerning the condition and stability of the rock mass through which the energy has traveled. In the following sections, the basic instrumentation required for seismic and microseismic studies is described, and some of the presently used applications of these methods are discussed to exemplify the state of the art. INSTRUMENTATION Seismic disturbances in a rock structure generate two types of seismic wave radiation, body waves and sometimes surface waves, which radiate outward in all direc¬tions from the source of the disturbance. Underground mining applications are generally concerned only with discerning the characteristics of the resulting body waves, i.e., the compressional (p-wave) and the shear (s-wave) energy. As these two forms of energy travel through the rock structure, the particles of the rock mass are caused to vibrate, and the vibration character¬istics resulting from each of the two types of wave are distinct. Some important differences are: 1) Compressional and shear waves travel at different velocities through the rock structure. 2) The frequency at which each wave causes particles to vibrate is different, and may range from about 50 to 100 000 Hz. 3) The amplitude or energy level of each wave is different, with the shear energy usually being the greatest. These differences form the basis for equipment se¬lection for individual studies and for modern data analysis techniques. The following sections describe the basic equipment necessary to detect and record seismic wave energy data and show several examples of analysis procedures and how these procedures have been used. In principle, seismic equipment is very simple. It consists of a geophone (or geophones) to detect the seismic energy vibration and convert that vibration to an electric signal, an amplification system to increase the level of that signal, and a means of monitoring and/or recording the signals detected. Fig. 1 is a block diagram of a typical system. The following sections offer a very brief discussion of system components and their individual functions. A more complete discussion is given by Blake, Leighton, and Duvall (1974). Geophones The function of the geophone is to detect the vibrations caused by the passing of the seismic wave energy and to convert that vibration into an electrical signal that displays both the amplitude and frequency characteristics of the vibration. Particle motion or vibration can be quantified and measured by measuring displacement, velocity, or acceleration of the particles. Thus, there are three types of geophones: displacement gages, velocity gages, and accelerometers. The choice of gage depends on the characteristic frequencies of the seismic energy to be monitored and the sensitivities of each type of geophone. In general, displacement gages are used for low-frequency monitoring (periods to 1.0 Hz), velocity gages for medium-frequency monitoring (1.0 to 250 Hz), and accelerometers for high-frequency monitoring (250 to 10 000+ Hz). Experience has shown that in underground studies, the choice of which gage to use lies between velocity gages and accelerometers. An easy, accurate method for selection of gage type is discussed by Blake, Leighton, and Duvall (1974). Once the type of geophone has been selected for use, it must be properly installed, and in the installation procedure the most important step is insuring that the gage is firmly attached to a competent portion of the rock structure. Poorly mounted geophones may entirely fail to recognize low-level seismic signals and will distort the information from signals they do see. Amplifiers Seismic events associated with mine structures occur over a very broad range of energy which results in a broad range of geophone output levels. In general, geophone output levels occur in the microvolt to low milli-volt range, and it is necessary to amplify these signals in order to drive recording or monitoring equipment. Because either an accelerometer or a velocity gage might be used as the geophone, the amplification system must

Jan 1, 1982

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By M. C. Williams, T. P. Meloy

With the increasing power of computers to simulate and control processes in the mineral industry, predicting the potential use of computers in the minerals field is not a hazardous enterprise, but predicting the timing of their use is. Like the railroad industry, technology invades the mineral industry, rather than being an industry like electronics that creates technology. Because of this invasive nature of computer technology in the minerals field, this paper predicts what will be possible to do effectively and economically with computers in the mineral industry. Moreover, this paper explores the problems of using the emerging computer technology in the mineral industry. For example, if not now, it soon will be possible to control the output of a mineral processing circuit - high grade, high flow or a mixture of it - to meet the daily market conditions and to sell each day that daily "mill" output as "mill" futures on the commodity market. Finally, suggestions are made which may be done to prepare the industry for the computer revolution in the mineral industry.

Jan 1, 1993

By Jim Peregoy

INTRODUCTION Frontier-Kemper Constructors, Inc. is an Evansville, Indiana based heavy construction contractor engaged in projects for both the public and private sectors of the underground construction industry. Construction activities range from conventional shaft, slope, tunnel and chamber excavation through state-of-the-art mechanical excavation, ground freezing, standard support and structural concrete operations. Conventional excavation and concreting equipment, as well as raise boring machines, road headers, tunnel boring machines, and freeze plants are owned, operated, maintained and modified "in-house" to suit the needs of individual projects. The balance of this paper wilt present a general overview of the Frontier-Kemper planning and construction operations on the recently completed Phase II of the U.S. Army Corps of Engineers, John Day Dam, Juvenile Fish Bypass Project. General Project History The U.S. Army Corps of Engineers is responsible for designing, constructing and maintaining various navigation and impoundment structures on the nation's inland waterways. Maintenance involves both the work required to maintain the structure in fully-operable condition and the ongoing work required to maintain a positive impact on the environment. John Day Dam is located on the Columbia River approximately 95 km (60 miles) upstream of The Dalles, Oregon. It was constructed to: provide electric power to the Pacific Northwest; provide Locking for up-and-downstream bound commercial and private watercraft; act as a water impoundment structure to control flooding conditions; and to provide a source of irrigation water

Jan 1, 1987

By Lars Söderberg, Eric Sandström, Per G. Broman

INTRODUCTION Boliden Mineral AB currently mines sulfide ores in 18 mines and processes them in eight concentrators. Most ores are typically complex. Gold consti¬tutes a considerable part of the value of the ore reserves. The value of total production in 1984, distributed by different metals is shown in the pie chart below. Traditionally, gold has been recovered as a byproduct, or coproduct, along with silver in floated copper and lead concen¬trates. Gold-price trends over the past decade have prompted comprehensive efforts by Boliden to increase the recovery of gold in concentration processes. Gravimetric recovery of gold in the grinding circuit is one method that has led to quick results. This method supplements tradi¬tional recovery processes based on flotation. The development of a feasible circuit, and the results obtained by its application in the central concentrator at Boliden, in the northern Swedish province of Västerbotten, are reported below. GOLD MINERALOGY IN BOLIDEN ORES The gold content in Boliden Mineral's ores is primarily in the form of alloys with the elements silver and mercury. A minor quantity appears in an unalloyed form.

Jan 1, 1986

By T. E. Walsh

Introduction I will address two important alternative energy resources, solar and geothermal, with emphasis on their potential application in electric power generation. As a result of this presentation, I hope to leave you with a realistic view of the principal technology options that are being developed or that are available. Solar Types of Collection In terrestrial solar applications, the biggest challenge is to find ways of collecting the sun’s relatively low intensity energy so it can be converted economically to useful thermal or electric energy. Fig. 1 shows that there are both natural and technological ways of collecting solar energy. In nature we find that solar energy aids in the production of biological growth, rainfall, and wind, all of which can, in one form or another, be put to use in the production of heat or electric power. The sun’s rays also are collected and stored naturally in the form of heat in the upper layers of the ocean which can be put to use in the production of electric energy by means of ocean thermal energy conversion (OTEC) approaches. On the technological side, the sun’s rays can be intercepted by materials that directly absorb and convert its energy to low-grade heat, or by mirrors or lenses that focus the rays onto a material to produce high-temperature heat. The higher temperature systems can be used to drive efficient heat engines in the production of electricityy. The sun’s rays also can be collected on photosensitive materials, in either a direct or concentrated form to generate DC electricity directly. The systems I will discuss employ all of these means of collection and conversion, excluding biological and hydroelectric. The former is too ex

Jan 1, 1980

By Takashi Sakaguchi, Akira Nakajima

Some attempts were made to recover and remove heavy metal elements, such as uranium, copper and chromium, from aqueous systems by using several phosphate compounds. The phosphorylated derivatives of polysaccharides, chitin phosphate, chitosan phosphate and cellulose phosphate, have high abilities to accumulate heavy metals, such as uranium, copper, manganese, cobalt, cadmium, zinc, nickel and chromium, compared with non-phosphorylated polysaccharides. In order to obtain basic information on the recovery and removal of uranium that may be present in industrial effluents, mine waste water and seawater, the adsorption of uranium by chitin phosphate and chitosan phosphate was investigated in details. The adsorption of uranium by chitin phosphate and chitosan phosphate was much greater than copper, cadmium, manganese, zinc, cobalt, nickel, magnesium and calcium. The adsorption of uranium was very rapid and was affected by pH of the solution, temperature. granule radius and co-existence of carbonate ion. The amounts of uranium adsorbed on the adsorbents increased linearly as the external uranium concentration increased. Uranium adsorbed on chitin phosphate easily desorbed with diluted sodium carbonate solution. On the other hand, uranyl and cobalt ions were separated from each other by using chitin phosphate. Along with these fundamental research, some attempts were made to recover uranium from seawater.

Jan 1, 1993

By R. D. Schmidt, M. J. Friedel

Unsaturated permeability and flow capacity exist where copper mineralization is disseminated in segmented, very-low-permeability ore blocks. The US Bureau of Mines (USBM) investigated this condition for application to in situ, copper-leach mining at the Cyprus Casa Grande mine site. Moisture retention properties are derived and combined with scanning-electron-microprobe data to characterize the host rock's mineralogy, texture, pore size, distribution and permeability. Finite element modeling is used to estimate saturated permeability and the ambient degree of saturation and to gain insight into appropriate in situ leach design. Recommended design modifications for optimized solution distribution and maximum recovery from the Casa Grande ore require: • well pressure injection exceeding 1500 psi and recovery wells operating in a suction mode, or • secondary, permeability enhancement by explosive rubblization. In the former, the lack of conditioning and the use of lesser pressures will result in leach solutions confined to the macrofractures. With the latter requirement, pressures can be reduced to 500 psi, with improved recovery and solutions containment.

Jan 1, 1993