Search Documents

By V. A. Leach, Lokan. K. H., S. B. Solomon, R. S. O’Brien, L. J. Martin, K. N. Wise

INTRODUCTION The development during 1979 of a relatively small, but high grade (10,000 tonnes uranium at an average grade of 2 per cent), uranium ore body at Nabarlek in the Northern Territory, Australia offered an excellent opportunity to obtain detailed radiation data for an open cut mine operating during the dry season. The ore body (Queensland Mines Limited-1979), which was completely extracted in a period of four and a half months, consisted of a vein type deposit dipping at 30 to 45 degrees and contained a central core of pitchblende in massive and irregular pods, surrounded by lower grade fine grained disseminated pitchblende. Mineralisation extended from the surface to a depth of 72 metres over a length of 230 metres with an average but variable thickness of 1D metres. Ore near the surface had been heavily weathered and complex secondary minerals were formed which had dispersed from the main vein. Mining was carried out with large earth moving equipment. Overburden and weathered surface ore were removed initially with scrapers. At greater depths bulldozers were used to rip and assemble ore and rock at each level, and these were removed by large trucks to the ore and waste rock stockpiles. Where necessary, blasting took place during shift changes each evening. Mining was essentially continuous with two ten hour alternating shifts working for thirteen days out of fourteen. At the completion of mining a relatively small excavation (335m x 185m x 70m) remained, and this will serve as a tailings repository during the milling phase. FIELD MEASUREMENTS The inhalation of radon daughters, arising from the radioactive decay of radon gas is well established (Archer et. al. 1973) as a potential hazard in the uranium mining industry. Control over radon and its daughters to ensure that recommended exposure limits are not exceeded is achieved by providing adequate ventilation, and under normal circumstances natural ventilation from an open pit should be sufficient. However, during the dry season it is not uncommon for stable atmospheric conditions, with little horizontal air movement, to develop - particularly at night - and significant radon daughter concentrations may accumulate. Throughout the entire mining period measurements were therefore made of radon and radon daughter levels at representative locations within the pit and on the ore stockpile as it developed. Initially these measurements were carried out manually, using the Rolle method for radon daughters, (Rolle 1972) and .scintillation cells (Lucas 1964) or a two filter tube for the determination of radon (Thomas 1970). For the latter half of the period however, a continuous recording instrument, developed within the Laboratory was used to provide a detailed record of radon daughter levels within the pit. At the same time, continuous readings of wind speed and direction, and vertical temperature gradient between 10 and 3D metres were recorded on a 30 metre meteorological tower, situated 800 metres from the pit. Radon Emanation Rates It is evident that radon and radon daughter concentrations depend on the grade, or more particularly, on the surface radon emanation rate of the ore which is exposed. Accordingly, as the mine progressed, detailed measurements were made of both of these quantities. The surface emanation rate of radon was determined for each ore bench as it was exposed by placing an extended array of canisters, filled with freshly degassed activated charcoal, face down on the ore for a known time. These canisters, which had previously been calibrated in the Laboratory, adsorb radon with high efficiency, and the total radon adsorbed is measured after retrieval by detecting the gamma rays from the trapped radon daughters (Countess 1977). At the same time, as each canister was placed in position, a measurement of the local ore grade was made for each location. This was achieved with a calibrated sodium iodide scintillation detector, adjusted to detect the 609 keV gamma ray from the isotope 2148i, a decay product of radium. Finally, measurements were made of the radiation field 1 metre above the surface, with a gamma ray survey meter, which was calibrated in the Laboratory. The relationship between the scintillator count rate and ore grade was determined by comparing the scintillator output with the gamma monitor, and relating the latter measurements to ore grade (Thomson and Wilson 1980). It was observed that while emanation rates and ore grades varied widely, the ratio of emanation rate to ore grade was in general fairly stable. A plot of this ratio is presented as a function of depth below the original surface in Figure 1. For most observations the ratio is constant at a value of 80 Bq m-2 s -1 per unit ore grade, where ore grade is expressed as percentage of U308. At the surface however, where the ore was weathered, the ratio was about a factor of three higher, and at two particular depths, where high grade pitchblende was being removed, it was very much lower. This was not unexpected as earlier Laboratory studies of drill core samples from Nabarlek had indicated that the emanation coefficient (the fraction of radon produced within the ore which escapes from the mineral particles) decreases with increasing ore grade.

Jan 1, 1981

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988

By E. Wiewiorowski

A new technology for recovery of metals from spent catalysts containing aluminum, cobalt, molybdenum, nickel and vanadium was developed. The catalysts are decomposed in two consecutive pressure leaching steps. Sodium aluminate-sodium hydroxide systems are lixiviants in both leaching steps. Selective extraction of molybdenum and vanadium is achieved in the first leaching step. The leach liquor is processed for separation and recovery of these two metals. The residue from the first leaching step is further processed in a second leaching step where alumina is solubilized. The residue from this operation is a nickel-cobalt concentrate. Alumina is separated from the second stage leach liquor by precipitation; the depleted liquor, a sodium aluminate solution, is recycled to the first and second leaching step. This technology has advantages over other approaches for the recovery of metals from spent catalysts because no solid waste is generated.

Jan 1, 1988

By S. A. G. Poppen

The lining of a mine shaft is one of the most important considerations in the planning and operation of an underground mine. Generally, the function of a shaft lining is to preserve the shaft opening in a manner compatible with the expected mine life and -the other shaft operations. Where shafts are the only means of surface access in a mine, they also serve a critical function for the safety of the entire underground operation. Routine repairs and maintenance work on the shaft linings are only possible in stable strata with only minor interruptions to the shaft operations.

Jan 1, 1988

By J. Kircher

Nevada Goldfields' Aurora Mine consists of a 270 mtpd (300 tpd) precious metals mining and milling facility located 28 miles southwest of Hawthorne, Mineral County, Nevada and lies within five kilometers of the Nevada-California border. (Figure 1) Ore production presently is derived 85% from an open pit source with the balance from underground. The Aurora Mill is a compact conventional cyanide plant utilizing a carbon-in-leach extraction process followed by stripping of loaded carbon and electrowinning at Nevada Goldfields Kingston Mine, located near Austin, Nevada. Production commenced in December 1987 and annual gold production is currently 20,000 troy ounces of gold and 22,000 troy ounces of silver per annum, produced at an average cash cost of $178 per ounce of gold. Tailings handling at, Aurora was originally accomplished using a belt filter press producing a solid cake that was then transported to a final storage area. Although overall operating costs at the mine were' in the lower percentile of producing gold mines, the tailings handling portion of the operating costs were inordinately high.

Jan 1, 1989

By B. R. T. Simoneit

The formation of petroleum is normally thought of as a geologically lengthy process, involving the accumulation of organic matter, its gradual burial, diagenetic breakdown via geochemical reactions, maturation, heating within a 75-150'C "oil window" induced by normal geothermal gradients in the subsiding basin, and slow product migration into structural traps (Tissot and Welte, 1984, Hunt, 1979). The entire process can take millions of years and, indeed, most oil reservoirs probably formed in this manner. How-ever, today in sedimented, submarine rift basins (Fig. 1), Cl to >C40 hydrocarbons with the chemical and physical properties of crude oil are forming in demonstrably much shorter time by rapid thermal maturation of immature organic matter in hydrothermal regimes that are unusually high for sedimentary basins (Brault and Simoneit, 1988a, b; Didyk and Simoneit, 1988; Kawka and Simoneit, 1987; Peter et al., 1988; Simoneit, 1983; 1984; 1985a,b; 1988; Simoneit et al., 1984; 1987; 1988).

Jan 1, 1989

By P. Corser

Operational and geotechnical constraints on mining within steeply dipping deposits and historic landslide areas, which are characteristic of subarctic coal deposits in Alaska, will be discussed. The current plan for mining through these areas will be presented, as well as an alternative plan for minimizing the adverse effects of mining through an historic landslide area.

Jan 1, 1988

By J. Singh

Recently, a Maryland bank became the overnight owner of a toxic waste site through a foreclosure. The original property owners had operated a crash and garbage business on the site and obtained loans for their business venture through the bank. In 1980, their son purchased the property from his parents with mortgage monies obtained from the bank. Failing to make his loan payments, the son defaulted on the mortgage. The bank foreclosed on the property and eventually purchased the property at a foreclosure sale. Shortly after the bank's purchase of the site, toxic wastes were found on the property--the result of disposing solid wastes on the site for 10 years. The bank declined responsibility for contaminating the site and consequently for its cleanup. The Environmental Protection Agency (EPA) took corrective actions to clean up the site. EPA then handed the bill to the bank, citing the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) of 1980 (more commonly known as "Superfund"). CERCLA imposes liability on the current owners and operators of hazardous waste sites.

Jan 1, 1988

By A. MacG. Robertson

Where weak rock zones are encountered in the slopes of an open pit, they may control pit wall stability. Back analysis of slopes involving failure through weak rock enables an estimate to be made of the weak rock strength. A system of consistent rock mass classification is described which enables the weak rock mass material to be described and classified from drill hole core. Correlation with back analysis determined strength allows strength estimates to be assigned to each rock mass classification.

Jan 1, 1988

By G. M. Bernard

An overview presentation of the fast-track start up of Cerro Colorado, a new copper heap leach project in Chile's Atacama' desert. A brief explanation 'of location of the property, exploration history, geol-ogy, reserves and development are presented. The overview includes mining, crushing, agglomeration, and the solvent extraction-electrowinning recovery process. Challenges and requirements specific to heap leach systems will be addressed and analyzed. A detailed description will be given of the mobile heap leach conveying and stacking systems used in the building of heaps for on-and off-pad operations.

Jan 1, 1995

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By R. O. Y. Breese

The term "diatomite" implies the nearly pure sedimentary accumulation of diatoms. Sedimentary and chemical purity, low density, inertness, intricate fine structure, high brightness and other properties give the diatom and diatomite unique industrial usefulness and commercial value in high value functional filler and specialty filter aid products. Although diatomite deposits occur commonly throughout the world in Miocene and younger marine and lacustrine sediments, deposits that contain significant reserves of crude suitable for these quality sensitive markets are uncommon. U.S. production is centered on exceptional deposits located in Arizona, Nevada, Oregon, Washington and California. Evaluation of deposits requires understanding of geology, mining, production and end use. As crude quality in deposits varies within and between strata, ore suitable for quality sensitive end uses must be identified through sampling and evaluation programs tailored to permit recognition of critical variations.

Jan 1, 1989

By G. L. Merritt

The implementation of the Surface Mining Control and Reclamation Act of 1977 (SMCRA) has evolved into one of the most complex environmental protection programs to come out of the late 1970's. The level of detail in the statute and the regulations have resulted in a rigid and complex set of requirements for the administration, permit-ting, inspection and enforcement of the program. In addition, the constant change of the federal program caused by regulatory changes, reorganization of the Office of Sur-face Mining Reclamation and Enforcement (OSMRE), ongoing litigation involving OSMRE, and the use of the budget to establish additional mandates on OSMRE and the State Regulatory Authorities have resulted in an unstable program. The instability of the program makes it extremely difficult for the States to implement their programs and to achieve the goals of SMCRA.

Jan 1, 1988

By A. R. Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Nines Camchib Inc. It is characterized by very fine first generation gold and very coarse second generation electrum. Successful processing required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented.

Jan 1, 1989

By D. U. Gustafsson

After half a million meters drilled with Wassara we are now confident that ITH hammers powered with simple water will become an established product for production drilling. Today four drill rigs in LKAB Malmberget equipped with Wassara drill about 25 000 m per month of 4 1/2" holes. In Kidd Creek, Canada, Was sara is used for production drilling in stopes with good results. The first Wassara 6" hammer has drilled a 36 meter long, completely straight horizontal cut hole for drifting in the LKAB Malmberget Mine. Main advantages are about doubled penetration rate, very good air quality and improved hole cleaning which facilitates stabilized drilling. Disadvantages are resistance to new technology and, in some cases, the increased use of water.

Jan 1, 1995

By B. M. Davis

The Colosseum Mine is within the Clark Mountain mining district located approximately 72 km (42 miles) southwest of Las Vegas. Nevada in San Bernardino County, California. Gold mineralization at the Colosseum Mine is hosted in two 150 m by 210 m (500 ft X 700 ft) interconnected. rhyolitic intrusive breccia pipes that intruded Precambrian crystalline basement rocks and over-lying Paleozoic marine sedimentary rocks. Sub-sequent erosion (de-roofing) of all of the Paleozoic section and a portion of the Precambrian section has exposed the pipes to the present level (probably a significant depth in the original breccia pipe system).

Jan 1, 1989

By R. H. Sailors

During the last 15 years, the North American Mining Industry has experienced increasing usage of cast high chromium white iron grinding media in wet grinding applications. First introduced into the cement industry (klinker grinding) where wear rate reductions of four or five times have been realized compared to steel balls, this same grinding media serve the iron, copper, and phosphate markets by resisting not only impacts and abrasion, but also corrosion which occurs in wet grinding. In these markets, single mills containing 250,000 kg of grinding balls are not un-common and hence the economic potential with respect to lower wear rates can be significant. Add to reduced wear rate the increased production efficiency that is possible and it is readily understood why much of the mining industry uses cast high chromium grinding media. Metallurgically, the alloys used consist of a martensitic matrix containing hard M7C3 eutectic carbides. Carbon (2.0 to 3.5%) and chromium (12 to 277.) are characteristically used to arrive at the desired properties.

Jan 1, 1989

By John C. Stam

During the past 20 years, the seismic refraction method has been used for depth to bedrock investigations. Its usefulness, however, has been recognized mainly in engineering applications, for instance in connection with the construction of power stations and in dam site investigations etc. Although some knowledge of the depth to bedrock can be of advantage in many other fields, the use of the conventional 12 or 24 channel seismic refraction equipment has been very limited, especially in ore prospecting and mining operations. The reasons for this are mainly the rather complicated operation of the instruments and the high costs. A conventional seismic equipment requires a crew of six men, a highly trained operator and an interpreter. Furthermore, the use of explosives can under certain conditions be undesirable (naighbourhood of houses, damage to agricultural areas etc.). Since 1957 a new one-channel seismograph, 'constructed by Geophysical Specialties Company, Minneapolis, Minnesota, has been in use and this instrument simplifies operations and reduces their costs considerably.

Jan 1, 1959

By S. A. Abetel Sabour

In this work, the block theory was applied to determine the safe limit of the angle of face slope at Limestone quarry of Assiut cement company in order to decrease the occurrence of dangerous potential key blocks. Four joint sets were observed and measured at the face. Computer program based on the vector analysis technique was developed to determine the removable block codes. Stereographic projection was also used in this work to determine the removable block codes and to calculate the maximum limit for the angle of dip of the free face, which was found to be 77°.

Jan 1, 1998