Search Documents

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By R. L. Derick

On a regular basis, mine personnel should obtain air samples directly from active underground areas as well as remotely from sealed locations. These samples provide mine officials with data relative to the makeup of the various atmospheres. Should conditions underground change, these results can provide a baseline that can assist officials in determining the extent of change. Relating the concentrations of individual gases to time, applying gases to equations, and examining their change over time are tools that have been successfully used to determine if a heating event exists and, if so, the extent of the emergency. These atmospheric status equations have either been developed for the mining industry or adapted from other industries. They serve as tools to assist personnel in determining the condition of underground mine atmospheres. As long as the problem area continues to be ventilated, certain gases, gas ratios, and equations can be used to determine if a fire exists, what type of material could be burning, and what quantity of coal is burning. Once the mine or the involved section has been temporarily sealed, gases, ratios, and gas-derived equations can assist personnel in determining how conditions within the sealed volume are changing over time. To alleviate potential explosions when fresh air is once again introduced into the sealed volume, equations and a diagram have been developed to predict the likelihood of an explosive atmosphere. Similarly, prior to commencing recovery of a mine or section, equations exist that can assist in determining if the fire will rekindle when air is reintroduced. This paper serves as an overview to remind and/or instruct readers about gas-sampling methodologies and gas analyses to assist in determining the status of underground atmospheres.

Jan 1, 2006

By Bruce Hebblewhite

Australia’s Minerals Tertiary Education Council (MTEC) has achieved several successes during its first three years of operation. This initiative was developed through the Minerals Council of Australia, in conjunction with three partner universities involved in mining engineering education. The partner universities are the University of New South Wales (UNSW); Curtin University, the West Australian School of Mines (WASM); and the University of Queensland (UQ). The collaboration between these partner universities and industry has led to the development of shared course material, cross-institutional teaching arrangements, and the development of a number of flexible, distance-based delivery programs. This article then discusses future initiatives. Importantly, the challenge is the future initiative planned to cement this collaboration by the formation of a “virtual” national school of mining engineering: Mining Education Australia (MEA). This will provide a common third and fourth year program to all three universities beginning in 2007. The common program will involve innovative teaching and learning arrangements, greater student exchange potential and a more significant input by industry into the education process.

Jan 1, 2006

By R. Todd Swinderman

"Higher production demands across all bulk handling segments require increased efficiency at the lowest cost of operation, in the safest and most effective manner possible. As conveyor systems become wider, faster and longer, more energy output and more controlled throughput will be needed. Add an increasingly stringent regulatory environment and cost-conscious plant managers must closely review which new equipment and design options align with their long-term goals for the best return on investment (ROI).There are primarily two separate market segments using conveyor belts. One is in process industries such as food, chemicals, paper and powders. Handled in relatively low volumes, the bulk materials that enter these processes are generally of a consistent size and quality. The other market includes mining, coal handling and cement, where the bulk material’s quality and size vary, and the volumes are typically much greater. While both segments face similar issues with safety and environmental control, the properties of the materials handled and the volumes transferred suggest different approaches, with one thing in common: increased belt speeds requiring modern equipment upgrades.Safety at higher belt speedsWith companies recognizing that safety does indeed pay, safety is likely to become a new source of cost reduction. The percentage of mines and processing facilities with a robust safety culture are likely to increase over the next 30 years to the point where it is the norm, not the exception. In most cases, with only a marginal adjustment to the belt speed, operators quickly discover unanticipated problems in existing equipment and workplace safety. These problems are commonly indicated by the larger volume of spillage, increased dust emissions, belt misalignment and more frequent equipment wear or failures."

Jan 11, 2018

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By Yuting Xue, Gamal Rashed, Zoheir Khademian, Connor Brown, Khaled Mohamed

Ground falls in U.S. underground coal mines can lead to significant consequences, including loss of life, injuries, damaged equipment, and production stoppage. Improving the safety of the workplace is of utmost importance for mine workers and the U.S. economy. The Mine Safety and Health Administration (MSHA) accident/injury/illness dataset provides short narratives for reported incidents, including ground-falls. The main objective of this study is to develop a framework that includes: 1) utilizing machine learning algorithms to categorize ground-fall incidents from narratives based on the main cause of the occurrence and 2) demonstrating an example of a user-friendly visualization to display injury/fatality trends from narratives in U.S. coal mines between 1983 and 2021. The developed framework was tested on a subset of the data and achieved an average F1-score of 96% in categorizing the incidents. The outcome will help identify areas requiring additional research and innovative solutions to reduce severe occupational hazards.

Feb 1, 2024

By I. Gombköto, J. Bohm

"In Europe, and therefore in Hungary opening a new mine is harder and harder. Depletion of mines, unfavourable legal and economic changes, and growing public concerns are the main reasons. Social and economic interests require total utilization of mineral raw materials of the operating mines, and furthermore utilization of waste heaps of the former mines. There are 5-6000 waste heaps of the operating and the closed mines in Hungary. 2000 of these waste heaps have already been estimated, and researches show that total amount of waste heaps can be calculated to 1 billion tones. These researches left out of consideration waste heaps exploited and placed in deep lignite mining. In several projects and researches we analysed processing of waste heap and possibilities to use its components. A processing technology for utilizing waste heaps has been developed based on laboratory and pilot plant tests. Great amount of useful materials of quarrying waste heaps can be utilized with this technology. Tests were also done for processing waste heap of a former ferrous metals mining. The developed processing technology contributes to use these waste heaps as aggregate for cement industry, as dielectric and aggregate for construction. The essay presents in details main characteristics of waste heaps, technologies already used for processing waste heaps of quarrying and ferrous metals mining, mass balances and qualitative parameters of the end products."

Jan 1, 2011

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulfide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular SO2 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, pyrrhotite, pentlandite, pyrite, chalcopyrite, and violarite have agglomerated and reacted to form two intergrown phases: 1) pyrrhotite solid solution (Fe0.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu0.03S). Magnetite formed euhedral crystals, skeletal crystals, and dendrites at the margins of the matte. Prismatic ferrohypersthene and octahedral Mg-Al-Fe spinel crystals and dendrites are present in the glassy slag.

Jan 1, 2001

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By David Van Horsen

Operation and maintenance of California?s water tunnels is an important factor and vital link in California?s infrastructure. These tunnels are owned and operated by a variety of large and small private and public water and power utility companies, municipal agencies, and irrigation districts. Visionary pioneers such as Michael O?Shaughnessy (San Francisco Hetch Hetchy Water Supply System), William Mulholland (Los Angeles Department of Water and Power and Metropolitan Water District of Southern California?s Colorado River Aqueduct), and John Eastwood (Southern California Edison Big Creek Hydroelectric Project) built large and small water supply, irrigation and hydroelectric tunnels, which have supplied environmentally friendly-water supply, renewable electricity, and uninterrupted service to a burgeoning population and economy. This paper introduces these pioneers and describes several case histories and lessons learned during condition assessment and rehabilitation of tunnels providing enlightenment of California?s vital water projects.

Jan 1, 2008

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By Andres Salazar, Carlos Delgado Robles, Richard K. Preece

Minera Escondida, located in the Antofagasta Region of northern Chile, is the world’s largest producer of copper as concentrate and SX-EW cathode. Projects to increase mill and flotation capacity began soon after start-up in 1990 to off-set decreasing copper grade. Subsequent projects had the objective to increase copper production through heap leach and SX-EW production and a second concentrator. The mine footprint concurrently expanded peripherally from the central high-grade enriched core of Escondida and then into the separate Escondida Norte deposit. Early in the mine life, metallurgical forecasting that was based on metallurgical composites of presumed ore types and historical plant production was adequate for operational planning, plant design, and project valuation. This approach became unreliable, however, as the increase in mine footprint was accompanied by an increased variability in key ore body characteristics such as hardness, copper-iron sulfide mineralogy, and sulfide liberation textures that were not reflected in the geological criteria used for ore type designation. The project study teams turned to small-scale physical and chemical tests to better characterize the spatial distribution of these key ore characteristics. Programs associated with capital growth projects were carried out through the mid-2000s to sample and construct a three-dimensional spatial model of hardness, copper sulfide mineralogy, and rougher flotation recovery from tests on 15-m drill core composites. Mathematical models were developed from the respective ore characteristic data to calculate throughput, flotation recovery, and concentrate copper grade. The spatial models were integrated with the concurrent mineral resource block model using standard geostatistical methods and the metallurgical process calculations were applied to the block estimates. The geometallurgical model, originally constructed on a project basis, is now managed by a dedicated team reporting to the manager of Geosciences & Resources Definition in the Escondida organization. The model has evolved with increasing complexity of the mine and processing plants and currently includes seven forecasting areas for three concentrators and four areas for two leach plants. Metallurgical forecasts of mill throughput, final flotation recovery, and concentrate copper grade still have the highest relevance to mine planning and optimization. Sample preparation, test procedures, and quality control methods are summarized for the ore characteristic tests important to these forecasts. Analytical results from recent annual sampling programs are presented for the hardness indices, rougher flotation recovery, and partial extraction copper analyses. Geostatistical analysis of the SAG mill hardness index is summarized as an example for the spatial estimation process. Mathematic models are presented for throughput (based on hardness indices), final flotation recovery (based on rougher recovery and plant calibration studies), and concentrate copper grade (based on sulfide mineralogy and empirical pyrite rejection studies).

Aug 31, 2023

By F. Wendling, R. C. Nascimento, S. S. Wendling

"The objective of this research is to study the quality of blast-furnace iron ore pellets with binary basicity 1 fired on a pilot scale using the two main firing processes that are presently in use in the world and comparing them. Currently, the great majority of pellet producers use the traveling grate process because of its higher production capacity. In this study, the physical and chemical qualities of the pellet feed, limestone, anthracite and bentonite were determined and the amount of additives for a blast furnace pellet with the defined basicity was calculated. The physical properties of the green and dried pellets were determined accordingly. Produced pellets, after being fired on a pilot scale using traveling grate and grate kiln, were subjected to chemical analysis and physical testing. No significant difference was observed in the metallurgical quality — that is, reducibility index (RI), reducing disintegration index (RDI) and swelling index (SWI) — of the pellets produced by both processes. However, a comparison of cold physical tests — tumble and cold compression strength — shows improved quality of the pellets fired using the grate kiln process.IntroductionThe development of human civilization owes much to iron and steel (Sun et al., 2015). Iron is the most used metal in the world, and it is the main component of steel, which is present in materials for structural engineering, automotive and general industrial applications (Liu et al., 2014). Increased global demand has led to a decrease in the resources of ore with high iron content (Zhang et al., 2015), and currently 95 percent of the iron ore in China needs processing before smelting as its iron (Fe) content is only about 30 percent on average (Liu et al., 2014).Pelletizing is a process to economically agglomerate iron ore pellet feed into pellet form. After balling, green pellets are conveyed to the final step of the manufacturing process (Pena, 1982). The process is a multifaceted one, involving high temperatures, air flow gas turbulence and complex equipment geometry (Larsson et al., 2009). The pellets are fed into blast furnaces, which are now predominantly used in the extraction of iron. Ore processing also requires physical separation, including crushing, grinding and water removal (Sun et al., 2015).The increase in steel consumption favors the exploitation of low-concentration ores and the production of pellets (Halt and Kawatra, 2014). Pellet quality is affected by various factors, such as their physical and chemical characteristics and their temperatures and residence times in the furnace (Halt, Silva and Kawatra, 2015). Different geological settings lead to a wide range of different minerals (Graça et al., 2015).This work aims to generate important information for the pellet industry in the area of physical and metallurgical qualities of the agglomerates obtained by two processes: traveling grate and grate kiln."

Jan 1, 2017

By VIVEK KASHYAP, Evody Tshijik Karumb, PATRICK TAYLOR

The partial reduction of zinc ferrite to zinc oxide and iron (II, III) oxide can enhance the leaching rate of zinc. Zinc ferrite has often been found as a major component of zinc residues and electric arc furnace dust. The Waelz process is an existing process for zinc ferrite processing, which requires a temperature of more than about 1200 °C to produce Waelz oxide containing ZnO. Since zinc residues have been deemed as a potential way for the extraction of zinc and other critical metals, it is important to analyze the reaction kinetics in the temperature range of interest. This manuscript discusses the chemical kinetics of zinc ferrite reduction by hydrogen gas. Several researchers studied the reduction of zinc ferrite with CO; however, unlike CO, the use of H2 gas as a reductant allows partial reduction of zinc ferrite even at low-temperature range (400–600 °C). Thermogravimetric analyses (TGA) experiments were performed in the temperature range of 300–700 °C with 10% and 30% H2, and the data obtained was analyzed using the isoconversional method of kinetic analyses. The standard models used for isoconversional kinetic analysis were chosen from literature and experimental data were fitted to determine the controlling mechanism and calculation of kinetic parameters of reduction of zinc ferrite. The rate of reaction was found to be increasing with an increase in temperature and partial pressure of H2 gas. The reaction could be divided into three stages, where reaction interface contraction was found to be the controlling mechanism at the initial stage of reaction. As the reaction proceeds, product layer thickness increases, and thus, diffusion was found to be the controlling mechanism. Roasting products obtained from TGA experiments were also characterized using a scanning electron microscope (SEM) to verify critical morphological details.

Jul 26, 2022

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By T. Karalis

Perlite is a generic term for naturally occurring siliceous rock. It is a form of natural volcanic glass the main constituent of which is amorphous silica (70-76%). Perlite, when heated rapidly to its softening temperature range, expands from four to twenty times its original volume, due to the presence of 2-6% ?combined? water, in a manner similar to popcorn as the H2O molecules vaporize and create countless tiny bubbles, which account for its exceptional physical properties: light weight (30-150 kg/m3), low thermal conductivity, cellular structure, in general. These properties make perlite adaptable for numerous end-uses, which can be distinguished into 2 categories: Expanded perlite applications in: a) Construction Materials market (e.g. Acoustical Tiles, light-weight insulating Mortars, self-levelling Concrete), b) Agriculture (e.g. Hydroponics), c) Food and Chemical industry (e.g. Filtration Media, Filler, etc.), d) Insulation and Heat resistance technology (e.g. Cryogenic vessels, Refractory Bricks, etc.). Unexpanded Graded perlite applications in: a) Phosphoric Fertilizers industry (additive in H3PO4 production), b) Foundry technology (slag-aid, insulating and heat resistance agent).

Jan 1, 2006