Search Documents

By Jr. Kermit Allen

A study was conducted for the AEC to determine the feasibility of constructing an unsupported 315 foot diameter spherical cavity at a depth of 2,700 feet in a salt dome. A cavity of this size and shape has never been attempted. It was determined that the three basic essentials for solution mining; adequate salt, fresh water, and a means of brine disposal were available at the Tatum Salt Dome in Lamar County, Mississippi. Assuming a large, unsupported mined opening of the size and at the depth required would remain stable, the most practical method of providing the cavity using solution mining techniques is by use of a movable blanket of air to control the water level to properly shape the cavity while removing the insolubles either with jetting or by conventional mining methods. It is estimated that, using the jetting method of insolubles removal, the cavity can be constructed in 24 months for approximately $7 million. Using conventional mining techniques to remove the insolubles and shape the final cavity, it is estimated that the cavity can be constructed in 36 months for approximately $12.6 million.

Jan 1, 1968

By G. S. S. Raman, M. S. Klima

Coal refuse slurries stored in tailings impoundments can potentially lead to environmental concerns such as effluent seepage, property devaluation, and in extreme cases, dam failures. Pressure filtration offers an opportunity to reduce the impoundment requirements by providing significantly drier solids. A full-factorial design was used to study the effects of temperature and pH on dewatering a refuse slurry obtained from a coal preparation facility in Pennsylvania, USA. The experimental results indicated a strong effect of temperature on cake moisture as the cake moisture after about 2800 s was 22% at 43 °C and only 36% at 10 °C for tests conducted at pH 3. ANOVA results confirmed the statistical significance of pH, temperature, and their interaction effect. Also, the results showed no significant differences between the tests conducted near neutral and alkaline pH values at low and ambient temperatures. On the other hand, Tukey's test indicated higher reductions in cake moisture at higher temperatures for lower pH values. This study affirms the need to monitor and control the pressure filtration process as throughput could significantly vary with changes in temperature and slurry conditions.

Jun 17, 2019

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By P. Schilizzi, A. Jarosz, M. Karmis

This paper is concerned with subsidence prediction methods and in particular with two techniques, one based on profile functions and the other on influence functions. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. In more detail, the hyperbolic tangent profile function, as developed by VPI&SU from field data pertaining to the eastern U.S. coalfields, and an influence function method currently being adapted for the same region, are presented and discussed. The applicability, advantages and limitations of these techniques are examined and comparisons are presented with field measurements. Computer software developed for the application of these prediction methods, for two widely used personal computer systems, are also discussed and a number of examples are presented demonstrating the potential of such programs.

Jan 1, 1986

By William M. Dowall

The recently completed in-pit crushing and conveying project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109 kt/ d (120,000 stpd) of copper ore, using regenerative conveyors capable of providing more than 5.5 MW (7000 hp) of equivalent electrical energy. The Morenci Mine is located 330 km (200 miles) east of Phoenix, AZ. Phelps Dodge Corp. owns an 85% interest in the mine. The remaining 15% is owned by Sumitomo Metal Mining Co., Ltd. and Sumitomo Corp. Copper has been continuously produced from the Morenci district since the late 1800s. Until 1989, run-of-mine ore was transported from active mining faces to the Morenci and Metcalf concentrators by truck and rail haulage. In that year, a system of in-pit, semi-portable crushing plants and overland conveyors was commissioned. This substantially reduced truck haulage and effectively eliminated rail haulage in the pit. The system used two semi-portable, in-pit crushing stations equipped with 60/89 gyratory crushers. The crushed ore from both plants reported to the first of two overland belt conveyors, arranged in series, for transport from the pit to a coarse ore stockpile. The system was "backed-up" by existing locomotive rail haulage.

Jan 1, 1993

By Mohamed Yusuff

Modern transportation systems are one of the most important achievements of our civilization and provide us with tools for broadening individual and social freedom of choice. The transportation system initiated today is handed dawn to the next generation, probably with little choice because of the enormous expenditure of monies involved, and influence their way of life as to where they should live and where they should work. The ever increasing antagonism between the citizens and the planners of the transportation systems necessitates a careful review of the entire planning process. The planning process can be broadly classified into: the goal formulation and decision making process; the plan development process; and the plan implementation process. THE GOAL FORMULATION AND DECISION MAKING PROCESS Goal formulation and decision making is one of the vital phases of the planning process and is primarily based upon social values. In measuring social values, the planner must employ an appropriate scale of measurement since in the absence of this yardstick, these values tend to became vague and abstract ideals. The need for major social programs and concerns (poverty, etc.) of the urban areas should be analyzed to determine the type of transportation system which would contribute to the solution.

Jan 1, 1974

In spite of a global economy that continues to seesaw and a U.S. Congress that is at odds with the president and themselves, cities around the world are still spending billions on their infrastructure. And that bodes well for the underground construction and tunneling industry and the professionals who work in it. In June, 1,405 of those professionals gathered in San Francisco, CA for the Rapid Excavation and Tunneling Conference (RETC). In addition to the first rate technical programming, attendees were able to see first-hand the latest in tunneling technology from 127 exhibitors who occupied 152 booths. Two short courses preceded the conference and two field trips were offered following the conference.

Jan 1, 2011

By H. H. Murray

The largest reserves of palygorskite in the world are located in Anhui and Jiangsu Provinces in East Central China. The deposits are Middle Miocene in age and range from 3 to 6 m in thickness. The deposits are the alteration product of basaltic volcanic ash. The Chinese Geological Survey estimates the palygorskite reserves are in excess of 200 million tons. The elongate particle shape results in unique colloidal properties. Large quantities are exported to Japan, Taiwan, Southeast Asia, New Zealand, Australia, and West and Gulf Coasts of the United States. The markets include agricultural carriers, paint, joint tape compounds, animal feed binders, catalyst support, drilling muds, and suspending agents for chemicals, pharmaceuticals, and medicines. The viscosity is high and the quartz content is generally 5% or less.

Jan 1, 2009

By Jue Kou, Lei Yu, Bern Klein, Lusheng Zhou, Chunbao Sun, Genzhuang Li, Reem Roufail, Amit Kumar

Magnetic liners can improve the performance of ball mills by increasing grinding efficiency, extending service life, and reducing maintenance costs. Despite their importance, the fundamental understanding and the quantitative investigation on the effects of the magnetic liners has not been addressed in the literature. This paper addresses this gap by studying charge motion, and how the use of a magnetic liner affects the breakage mechanism of the mill, using discrete element method (DEM) modeling and the Hertz-Mindlin contact model with relative velocity dependent (RVD) rolling friction. Charge motion was modeled under different mill speeds. Compared to conventional steel and rubber liners, the charge motion in the magnetic liner mill was predominantly cascading. Quantitative analysis of the energy dissipation within the mill was conducted to investigate mill breakage. Regardless of speed, over 50% of the total energy dissipation in the magnetic liner mill was in the form of abrasion and attrition. The results highlighted the appeal of magnetic liners in secondary and regrinding application, where abrasion and attrition are considered more efficient in the fine material breakage, and where impact is ideally minimized to reduce mill wear. A number of experiments were conducted to assess the effect of different model parameters on the performance of the magnetic liner mill. The highest abrasion/attrition intensity was observed with high values of the model parameters namely the restitution coefficient, static friction coefficient, and rolling friction coefficient.

Jun 12, 2019

Amid some of the worst economic conditions that the mining industry has been faced with in more than a decade, the mood among the large crowd at the 114th Annual Northwest Mining Association?s annual meeting was surprisingly upbeat. More than 2,200 attendees showed up at John Asuaga?s Golden Nugget Casino in Reno, NV for the conference held Dec. 1-5. And more than 200 companies exhibited in 240 spaces, including SME and the Minerals Information Institute. The number of attendees and exhibitors were the most for the conference in more than 10 years. The conference was held in Reno/Sparks for just the second time in its illustrious history but began under the cloud of global financial turmoil. Prior to, and during the conference, the industry news headlines were grim, to say the least. An alarming number of mine plans and expansions had been put on hold; hundreds of miners across the United States had been or were in the process of being laid off; commodity prices were falling and some of the biggest mergers in the industry fell through while miners around the world put the brakes on to take a wait-and-see approach. It was a painful time for many, but the downsizing actions taken by many mining companies was exactly what needed to happen, according to Industry Outlook Luncheon featured speaker Frederick Sturm. He is the executive vice president and chief investment strategist and member of Mackenzie?s Investment team. He has earned a reputation as one of Canada?s leading investors in natural-based companies and he also manages the Ivy Global Natural Resource Fund in the United States Sturm said that the mining industry has fallen hard and that he expects it to bounce back quickly, before falling hard again. In these tough times, he said, the companies that have pulled back on production early are doing the right thing in the long run.

Jan 1, 2009

By R. Pothina

The objective of this research was to develop a mathematical model for gyratory crushers to help in the prediction of energy consumption and to analyze dominant parameters that affect this energy consumption. The development of a gyratory crusher model was achieved in the following three main stages: mathematical representation and coding of the crushing process; building an amperage constant model to derive an energy-scaling formula; and modifying the amperage constant model to represent a full-scale model. Due to their significant influence on feed-size distributions, two blasting parameters, i.e., burden and spacing, were considered. The crusher parameters that affect energy consumption were also identified. A case study of an operating dolomite mine was performed. The results indicated that by changing the burden, spacing and crusher closed-side setting, the overall (blasting and crushing) costs could be reduced by 4.7% to 7.9% annually. It can also be concluded that burden and spacing values have a linear positive relationship with the crusher energy consumption, while closed-side setting values have an inverse linear relationship with the energy consumption.

Jan 1, 2007

By Leslie Burnside

Homestake Mining Co. set out to complete final reclamation at a former open-pit gold mine in west central Nevada. The goal was to exceed regulatory standards by satisfying the company's own high corporate standards for successful reclamation. Homestake's completion requirements challenged available technology due to the unsuitability of heap material as a growth medium, the harsh environmental conditions of the site and the region's lack of native growth medium. Accomplishing these goals required enlisting a multidisciplinary project team to develop, test and implement appropriate and cost-effective revegetation alternatives.

Jan 1, 1999

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By Steve Skelhorn

Edmonton South LRT is the latest expansion of the Subway system in Edmonton, Alberta, Canada: Consisting of twin 5.8m segmental lined tunnels, 280m long, driven by a Lovat EPB machine. The key challenges were as follows. A 6% downhill grade. Tight radius curves of 250m.Overlying structures within 3m of the tunnel. Strata consisting of sand above the water table, glacial tills and bed rock below the water table. Located within The University of Alberta Campus and adjacent to a hospital. Northern Alberta climate with winter temperatures routinely falling below—minus 30 degrees Celsius. This paper provides a case history and outlines the challenges involved in completing this project.

Jan 1, 2005

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

By K. A. Lewandowski

Agglomeration techniques are widely used by industry to form fine particles into larger masses that are easier to handle and process. One area where agglomeration is potentially useful is in heap leaching operations. With-out agglomeration, fine particles travel through the heap, clogging the spaces between the larger particles and resulting in poor leach solution flow. Poor flow of leach solution will result in long leach rates and/or decreased metal recovery. Agglomeration immobilizes the fine particles and therefore improves heap permeability to fluid flow. Additional additives (binders) are needed to prevent agglomerates from breaking up as leaching solution percolates through the heap. Type II Portland cement and lime are two well-known binders used in gold and silver leaching, but these are limited to alkaline leaching environments. Various other products have been tested as binders, including polymers. This paper summarizes the benefits of agglomeration in heap leaching and the results obtained from the testing of several different agglomeration binders in heap leaching operations.

Jan 1, 2009

By S. C. Langvik

The presentation named 'Dewatering of fines by Rotary Vacuum Disc Filters' has an opening why the filtration process is important to the Iron Ore Industry. It goes on to describe the various types of dewatering machines which have been used in this industry in the last 30-40 years, and where the vacuum disc filters now dominates. It presents also the most important design changes which have been made during this period to enhance performance. Further are discussed the principles of filtration and the factors and parameters which influence performance and operating costs. As a closing is presented today's ideas and thoughts about what can be foreseen of design modifications and improvements in disc filter design in the coming ten years.

Jan 1, 2001