Search Documents

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By James R. Walpole

Less than 100 years ago the first major federal regulatory agency, the Interstate Commerce Commission was established (in 1887), and since that time literally hundreds of other federal agencies have been created. The regulations set by these agencies tremendously affect the individual citizens of this country as well as U.S. institutions. A few examples of the myriad agencies established include the Food and Drug Administration. (1907), the Bureau of Mines (1910), the Federal Reserve System (1913), the Federal Trade Commission (1914), the Tennessee Valley Authority (1933), the Securities and Exchange Commission (1934), the National Labor Relations Board (1935), the Small Business Administration (1953), the Federal Maritime Commission (1961), the Equal Employment Opportunity Commission (1965), the Farm Credit Administration (1971), etc., etc. Eight years ago, on December 2, 1970, still another federal agency was established by the reorganization plan of President Nixon -- the Environmental Protection Agency (EPA). The Administrator of EPA was given authority to regulate certain activities affecting the environ-ment, which were formerly within the jurisdiction of the Department of Interior, the Department of Health, Education and Welfare, the Federal Radiation Council, the Atomic Energy Commission, the Department of Agriculture, etc. Within weeks after the formation of this Agency, Congress began to enact legislation which would be administered by EPA. Over the last eight years a considerable number of such laws have been passed, a few of which include: the Clean Air Act (1970), the Noise Control Act (1972), the Federal Water Pollution Control Act (1972), the Marine Protection, Research, and Sanctuaries Act (1972), the Federal Insecticide, Fungicide and Rodenticide Act (1973), the Safe Drinking Water Act (1974), the Toxic Substances Control Act (1976), the Resource Conservation and Recovery Act (1976), the Clean Air Act Amendments of 1977, etc. It may be helpful to review, in a summary fashion, the major provisions in some of these statutes, and accompanying regulations, as they relate to water quality control in the mining industry. The Safe Drinking Water Act and the Federal Water Pollution Control Act contain provisions to be examined, as well as the Resource Conservation and Recovery Act and the Toxic Substances Control Act. One other law, the Surface Mining Control and Reclamation Act (1977), is not administered by EPA although it does contain many provisions related to environmental control, and it will also be dis-cussed because of its importance to the mining community.

Jan 1, 1978

By Walter E. Heinrichs

Early history of the district is typical of many, particularly in Southwestern United States. The usual early Spanish influence was felt; Marcos de Niza, Coronado and Father Kino are most notable, but authentic records regarding Spanish mining activities are sparse. About 1769 the Indian village of Tucson became a Spanish settlement. During the next century prospecting attempts were largely interrupted by the Indian, Mexican and Civil Wars. By 1870 Tucson had a population of 3200 and by 1880 the Southern Pacific Railroad extended all the way from Los Angeles. Pyrometasomatic copper ore was first produced with some local direct ore smelting done during the late 1800s. By 1907, a rail line was built from the Twin Buttes mines to Tucson by the Twin Buttes Mining and Smelting Company. World War I was a very active period, with mixed copper, lead, zinc, gold and silver production. This came mainly from underground replacement and contact metamorphic deposits and from practically all portions of the district. Some of these operations continued intermittently until the 1929 depression.

Jan 1, 1976

By R. B. Krog

The use of belt air as an intake source at longwall operations has changed greatly over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors, including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different than for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with the belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2010

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air pollution control is included. However, there are clear indications that natural gas supply from the contiguous 48 states and continental shelves will not indefinitely keep up with this rapid growth in demand. Projections are presented which define the extent of potential deficiencies from the 1970&apos;s to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale - by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current minemouth prices - 60-70 million&apos; tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase is gas demand.

Jan 1, 1969

By G. Ferrara

The paper describes the new design criteria and control strategies for multi-density dense medium separation (DMS) circuits. The role of the multi-density separation is discussed, and it is emphasized that for many processing problems -related to minerals and coals -it may be very important to perform two or more cuts at different densities in order to obtain a remarkable improvement in quality of products, process efficiency and economy. The two-density separation by dense medium cyclones was generally performed using two dense medium plants in sequence. In contrast to the former technology, the multi-density separation can now be performed by using a single medium circuit composed of different interconnected medium sumps. The sumps, one for each density, are fed with different medium streams selected according to their density, size composition and content in non-magnetic contaminant in such a way that the rheological properties of the media are optimized. This new technology is based on dynamic systems to density the medium, on the size-density segregation of the medium in the cyclones and separating devices and on accurate control systems for the density, viscosity and stability of the dense media of the different sumps. The present paper reports on the theoretical basis for the new, advanced medium circuits and on the systems for the control of the densities and of the rheological properties of the dense media. A typical circuit for a two-density separation is also described, and some industrial applications reported and discussed.

Jan 1, 1994

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept&apos;s economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By T. W. Camm

Some of the defining characteristics of narcissists include a grandiose sense of self-importance, preoccupation with success and power, a sense of infallibility, and a supreme confidence in their ability and intelligence. Ironically, many of these characteristics are rewarded in business organizations, which may explain why there seems to be so many narcissists in management positions. Assuming we will be dealing with narcissists throughout our career, it makes sense for us to understand what makes them tick, and more importantly what we can do to work with them in a constructive manner.

Feb 23, 2014

By S. G. Malghan

Flotation is the primary method for copper minerals separation from porphyry ores. The need to process difficult-to-float porphyry copper ores presents challenges to engineers and scientists in several areas. This paper is concerned with summarizing generalized problems faced in the processing of porphyry ores and treatment methods to overcome the specific problems. Though some of the problems are interrelated the problems have been classified into three broad catagories. The case studies of some of the successful applications of innovative methods to solve problems related to ore mineralogy, metallurgical aspects of ore treatment and process variables show that quite often the problems are solvable by a judicious choice of flotation variables.

Jan 1, 1984

By J. P. Gliddon

Since 1980 a number of significant changes have been introduced at Palabora in an effort to off-set the effects of reduced product price and increased unit cost of inputs. These changes and improvements include major equipment rationalization programs, the introduction of trolley assisted truck haulage, adoption of a sophisticated computerized truck control system, pit design enhancements, improved drilling practices, use of emulsion explosives and the installation of an in-pit crushing and conveying system. The various changes, their effect on the operation and their contribution to cost reduction and improved productivity at Palabora are considered.

Jan 1, 1987

By F. H. Buttner

Commodity currency intrigues most of us because of the problems it offers to solve for the Third and the First Worlds. What problems might be solved, if commodity currency were to be adopted in the Third World? That is really the question we are probing here right now. It would take a while to think through all their subtle consequences of this question, but, off the top, it might well have at least three important impacts. Most important of these to this audience is relief from unfair Third World competition. Second, it might well liberate Third World economies from financial indebtedness to the First World and give them freedom from the liquidity limitations. The third benefit is that it might help relieve World trade tensions. All three benefits are interrelated. We could start our speculations on the application of commodity currency from anyone of these starting points. But let us use the starting point most important to you, unfair competition to the U.S. mining industry. From there we might wind up with some thoughts on things you, yourselves, can do to improve things.

Jan 1, 1978

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By Donald T. Mylar

It is axiomatic that in designing a bulk material handling system the primary consideration is the functioning of the machines. The structure is secondary -its reasons for being are to support, enclose and provide access to the machine, for servicing. This results in a wide variety of supporting structures. Other considerations are: plant layout, local soil conditions, climate, local laws and codes, and last, but by no means least, the Customer&apos;s wishes.

Jan 1, 1971

By Robert Hochscheid

When the original water-only cyclone patents were established in the 1950?s, the supplies of low cost oil and natural gas were abundant and low selling prices for metallurgical and steam coal provided little incentive for developing more sophisticated coal cleaning systems. Bituminous coal sold for less than $5.00 per ton, and in this period many domestic coal producers discarded to the slurry pond the coal finer than 0.5-mm. For many producers, the selling price would not permit the recovery of the capital and operating costs required for dewatering and drying the fine coal. Water-only Cyclones Clean Fine Metallurgical Coal The first broad interest in the water-only cyclone became evident in the mid- 19601s, and though some work was done on coarser coals, investigators were particularly interested in cleaning coal finer than 0.5-mm. Flotation was the only fine coal cleaning method that was broadly accepted, but short-comings were recognized and investigators were looking for an effective fine coal cleaning device or system. Because of the greater market value and the need for reducing pyritic sulfur in metallurgical coals, much of the development work of the 1960&apos;s was done on coking coals.

Jan 1, 1981

By Ronald W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well-exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from non-kiaberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques in which spectral bands are chosen to optimize contrast between he kimberlitic soils, non-kimberlitic soils and vegetation. Careful processing of the multi-spectral data is also essential in order to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1984

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By Arthur L. Raub

During the last decade, there haven&apos;t been any great innovations in the design features of a copper concentrator. What has worked well in the past continues to work well, so that major breakthroughs have been minimal. Conservatism in the ranks also plays an important part. As a copper concentrator is not designed and built everyday, Davy was elated to have an important part in this project. This is the story of the design of the oracle Ridge Project located north of Tucson on the back of Mt. Lemmon at an elevation of 5,900 feet on the N.E. slope of the Catalinas. The Oracle Ridge property, formerly known as the Control Mine, is owned by Oracle Ridge Mining Partners, a joint venture between Continental Materials Corp. of Chicago and Union Miniere of Brussels, Belgium; both or¬ganizations specializing in the non-ferrous metal industry.

Jan 1, 1979

By John S. Wakeman

The initial step in the pelletizing of iron ores is the production of green balls. The importance of this step cannot be overemphasized as the physical quality of the green balls has a very significant effect on the subsequent induration process, regardless of the type of the indurating equipment employed. The ability of the green balls to withstand the rigors of handling, distribution, compaction and drying will have an effect on the degree of success of any pelletizing operation. Many factors affect the physical quality of the green balls including the prior processing of the iron ore, the characteristics of the balling feed and the type and quality of the binder used (if any). When working on the development of a new project or studying an existing operation, it is often desirable to determine what effect variations in these factors will have on green ball quality. It is generally impractical to make these determinations on a commercial, or even pilot plant scale, especially when the number of variables to be studied is large. Because of this, many organizations have developed batch techniques for producing green balls to enable them to perform such investigations with a minimum of time and expense. The batch balling method is at best, only an approximation of commercial balling systems. Many practitioners employ the use of pre-formed seed pellets to initiate a batch run. Thus, the growth mechanism encountered in any experiment is essentially snowballing. Unless an instability is introduced into a balling test (such as an excessive initial feed rate or an unusual feed material characteristic) the growth mechanism of coalescence is not present to a significant extent nor is it desirable. In a continuous operation, both mechanisms are present and necessary to sustaining the system. The batch balling technique thus produces pellets in an idealized manner and cannot be used to directly predict commercial green ball qualities. A general relationship does exist however, and the procedure is fairly sensitive to variations in test parameters. Although many refinements to this technique have been introduced over the years, batch balling is still essentially an art and subject to "operator effect". Therefore, to assure consistant and reliable results, skilled technicians who carefully adhere to established practice must be utilized.

Jan 1, 1971