Search Documents

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By Steven P. Oman

Large room and pillar mines are characterized by numerous and widespread working places. Ventilation requirements are high since each panel employs men and equipment that work simultaneously in multiple headings. Also, it usually is not feasible to redirect airflow from idle to active panels as the demands of each shift vary so every panel in the mine is fully ventilated at all times. Ventilation requirements will be even higher for mines that are classified as gassy. As a result of these considerations, ventilation systems for room and pillar mines are generally designed to handle large quantities of air. But as mining progresses and the mine be- comes larger, greater demands will be placed on the ventilation system. To insure that adequate ventilation is maintained at these times, ventilation engineers must anticipate problems and plan how best to deal with them.

Jan 1, 1983

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By G. G. O. O. Uwadiale, M. A. U. Nwoke

The flotation of Azara barite tailings was investigated using crude rubber nut oil (RNOc), refined rubber nut oil (RNOR) and oleic acid as fatty acid collectors. Chemical characterization of the rubber nut oils indicated high acidity, high saponification values and high iodine indexes, which are indicative of a high fatty acid compositions. The Azara barite tailings analyzed 64.6% BaSO4 by atomic absorption spectrophotometry. Gravity and magnetic separation techniques yielded a BaSO4 concentrate with a grade of 74.8% and a recovery of 92.5%. Barium sulfate grades of 90.0%, 92.8% and 94.8% with recoveries of 80.3%, 85.4% and 86.7% were achieved with collector dosages of 750g/t crude rubber nut oils, refined rubber nut oils and oleic acid, respectively. Hence, rubber nut oils are effective fatty acid collectors for the flotation of barite tailings.

Jan 1, 1998

By K. Hanumantha Rao, K. S. E. Forssberg, B. -M. Antti

Selective flotation of muscovite from a material containing muscovite (15.4%), biotite (13%), and siliceous gangue (quartz and feldspar), using a mixed collector system of sodium oleate and dodecylamine acetate has been described. Muscovite is found to float in preference to biotite, when the pulp is initially conditioned with oleate followed by amine at basic pH values. The results indicate that a product containing 63% muscovite with a recovery of 93% can be obtained, while using 75-150glt of oleate and 96 g/t of amine. The biotite grade and recovery are found to be around 30% and 20%, respectively. A good selectivity between muscovite and siliceous gangue is obtained. A final product containing 95% muscovite with an overall recovery of 75% is obtained when the flotation concentrate is subjected to magnetic separation. These studies indicate the possibility of separating muscovite from biotite by using a mixture of collectors.

Jan 1, 1991

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand and gravel mine sites throughout the United States. These interviews verified that the competencies included in the hazard recognition competencies framework agree with perceptions of the interviewed H&S professionals, who also provided validity for the critical role these competencies play. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

By P. K. Sollars, M. A. Alspaugh

In May of 1996, Twentymile Coal Co. began Longwall mining in the Foidel Creek Mine's East Mine District. These Longwall panels are some of the longest in the world (5.48 km/18,000 ft) with very difficult and challenging geometry. The conveyance system is 1,800 mm (72 in) wide, has a 4,500 mtph (5,000 stph) capacity and employs multiple tripper drives. The trippers include traditional powering designs as well as unique regeneration and braking designs. Several components were developed specifically for this application including a mobile tail brake. Control algorithms were carefully developed and tested via computer modeling. A world production record was achieved in the third month of operation and over 1 million tons were mined in June 1997.

Jan 1, 1998

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

By Nasser Madani, Yerbol Tussupbekov, Sergei Sabanov, Zarina Mukhamedyarova

A case study was conducted on a metal mine operating in Kazakhstan, in which problems were associated with use of a complicated and outdated ventilation system and its high expenses. The mine needs to reconsider its existing ventilation system and identify the risks associated with operational losses when using this ventilation system. The aim of this study was to develop an efficient risk analysis method capable of estimating operational risks and financial benefits of the existing mine ventilation system. The developed risk analysismethod considers ventilationmodelling, riskmodelling, and financialmodelling.Ventilation modelling comprises ventilation simulation and ventilation financial simulation. In risk modelling, the number of risk events occurring with the use of existing ventilation system and the operational losses during these events is estimated. Financial modelling considers operational losses and ventilation financial simulation benefits and uses a dynamic cash flow model to estimate how cost variability influences the cash flow. As a result, the improved ventilation system attains an additional NPVa ranging from 3.2 to 8.5 million US$ at the corresponding defined probability of 90%. The results of this study reveal that the developed risk analysis method can efficiently estimate the financial benefits of ventilation modelling and consider risk events and their total operational losses associated with use of the existing ventilation system. This approach provides a range of possible outcomes and helps with deciding whether the ventilation system is appropriate or whether it should be updated to better suit the project financial benefits.

Jun 3, 2020

By Zachary D. Jones

"Construction projects involve a great many risks. The risk that material prices will increase during construction or that the work under construction will be destroyed by fire, storm or some other act of God are just a few examples. In tunneling or other underground projects, one of the most significant risks is that the subsurface conditions encountered during construction will differ from what is expected. Each of these risks must be accounted for, managed and, ultimately, the duty of one party or the other to bear. The primary tool used to allocate the risks among the parties is the construction contract.How construction contracts allocate the risk that subsurface conditions will differ have changed substantially over the past century. Today, construction contracts typically allocate the risk through a series of provisions. The first is the differing site condition or changed condition clause. That clause, when included, typically provides that the owner bears the risk that the subsurface conditions will differ from what is indicated in the contract documents or what is reasonably expected. The second clause is one that provides that the contractor must conduct a reasonable site investigation and bear the risk of any conditions that such an investigation would reveal. The third provision includes disclaimers that are often included in geotechnical data provided by the owner (or the owner’s engineer) to the contractor which attempts to limit the information on which the contractor can rely. Because these risk-allocating devices seem to be somewhat conflicting, a brief discussion of each provides critical insight in understanding how the modern construction contract allocates the risk of differing site conditions.At the start of the 20th century, construction contracts looked substantially different than they do today. For example, one contract for the construction of a public water tunnel in Chicago, IL, drafted around 1895 contained the following clause:The contractor must take the work entirely at his own risk. No extra allowance will be made for quicksand, hardpan or boulders."

Jan 1, 2014

By Jeremy Cawley, Horry Parker Jr., Clint Wilson

The 5180 m EPBM drive on the Lower Olentangy Tunnel (LOT) is predominantly within glacial overburden. To connect LOT with the existing OARS deep tunnel in limestone bedrock, the upper 15 m inside diameter Vine Street retrieval shaft telescopes down to 6.7 m in diameter and extends into the karstic Columbus Limestone to a depth of 51 m, where a 104 m SEM tunnel will connect to OARS shaft 6. Pre-excavation grouting was reuired prior to lower shaft excavation to reduce potentially high groundwater inows. This paper discusses the secant pile installation, grouting program, shaft excavation, and hydrogeologic observations.

Jun 23, 2024

By F. Calizaya

This paper explains and discusses a computer program developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain project, Nevada.

Jan 1, 1994

St. Peter sandstone is an arenaceous sheet that covers large area in North America. The interest for St. Peter sandstone has been increasing due to the upward trend for hydrofracturing and the consequent need for fracking sand. This material is possesses very unique mechanical properties. On the one hand, it is brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The underground mines that are working under this condition are lacking the ground control techniques for this particular mining environment. The geotechnical properties of the St. Peter sandstone were examined using uniaxial test, triaxial test, porosity test, flexural strength test. This paper aims to investigate the effect of microstructure on strength properties, utilizing microscopic studies, index test (porosity, size distribution).

Feb 23, 2014

By S. D. Irons

With the passage of recent national and state legislation aimed at tighter regulation of air pollution and smoke control, attention has been focused on a problem which has long confronted the coal industry--the disposal of coal waste with its inadvertent ignition. Even as recent as 1935, a decision from the Allegheny County Court of Common Pleas confirms the stand taken on control of burning coal refuse disposal areas. "The uncontroverted testimony is that there is no feasible method of operating a coal mine without a gob pile on the surface, as no use has ever been found for this troublesome by-product of mining; that every large coal mine has a large gob pile close to its tipple; that sooner or later these piles all ignite through spontaneous combustion; that practically every large mine in Western Pennsylvania has a burning gob pile, and that there is no known means of averting such a fire." 19* As a result of the past "no regulation policy," there are presently on the order of 500 burning refuse banks, of which 213, 142, and 49 are found in West Virginia, Pennsylvania, and Kentucky, respective¬ly. 18 Many of these refuse banks have burned for 40 years or more; many others may continue burning for a like period. It is estimated that the annual emission from these smoldering piles approaches 183,000 tons of pollutents which may produce many deleterious effects on the populace, property and vegetation in the proximity to the sources.16 To date, little progress has been made in alleviating the pollution from the currently burning refuse banks; however, numerous investigators who are researching the causes of ignition, as well as preventative disposal techniques (refuse compaction, layering and crushing to finer sizes) have met with some success in handling the newly discarded coal refuse.

Jan 1, 1967

By Robert W. Row

The run-of-mine coals in the U.S. being fed to coal cleaning plants have become increasingly finer due to the adoption of modern, mechanized mining methods, and economics are dictating that finer fractions, as well as the coarser fractions, be cleaned. Traditional dewatering methods (vacuum disc filters and centrifuges) are proving inadequate for preparing fine refuse for disposal or fine coal product for downstream handling. The Electric Power Research Institute has been supporting research into the nature and limitations of mechanical dewatering, and novel ways of improving it. The efficiency of various silicone-based chemicals at aiding dewatering was investigated, and it was shown that the final moisture content of hydrophilic coals after vacuum Filtration could be reduced by 1 to 5% with up to 40% increase in filtration rate by addition of one of several of these silicones. EPRI also has an on-going program at its Coal Cleaning Test Facility to investigate the performance of the Larox pressure filter in comparison with that of the disc filter and solid bowl centrifuge. While improvements to the dewatering performance currently being obtained in existing operating plants by such means are achieveable, a fundamental study has shown that, regardless of changes in operating conditions, there may be a limit to the lowest cake moisture content attainable by mechanical dewatering of a given sample of coal fines. Determination of this limit for a specific coal would be useful in designing facilities to dry and handle it.

Jan 1, 1984

By Li Zhang, Jing Zhao, Chuanwei Zang, Shuanlin Wang

The application of gob-side entry retaining (GER) in steeply pitching seam longwall mining with a hard roof has always been a difficult problem. Based on the simplified roof beam mechanical model, the traditional gob-side entry retaining by packing (GERP) roof structure evolution process and its problems with use in steeply pitching seams are analyzed. Therefore, based on the unique characteristics of the gangue rolling and accumulating in the steeply pitching seam, this contribution proposes an innovative method of gob-side entry retaining by roof cutting (GERRC) in steeply pitching seam and details its technical process. The roof structures of the GERRC and the GERP are compared. Taking the Chang Gouyu Coal Mine as a case study, field experiments were carried out. This research finds that the GERRC can both overcome the impact of rolling gangue on roadside support and make the rolling and stacking gangue become a roadside support. The roof structure of the GERRC is in a one-time statically indeterminate state, which is conducive to the stability of the roadway. In the field test, the total displacement of the roadway roof and floor is 97 mm, the supporting pressure of the serried single props is less than 28 MPa, and the props have no obvious bending phenomenon.

May 6, 2020

By James C. Barker

Alaska?s known mineral endowment includes some of the largest and highest grade deposits of various metals, including gold, copper and zinc. Recently, Alaska has also been active in the worldwide search for sources of rare earth elements (REE) to replace exports now being limitedby China. Driven by limited supply of the rare earths, combined with their increasing use in new ?green? energy, lighting, transportation, and many other technological applications, the rare earth metals neodymium, europium and, in particular, the heavy rare earth elements terbium, dysprosium and yttrium are forecast to soon be in critical short supply (U.S. Department of Energy, 2010). The REE, accompanied by other high field strength metals (such as Nb, Zr, Ti, Th, W), are associated with alkaline complexes of the Hogatza Belt in northwest Alaska; peraluminous tin-granites of the Ruby batholith in central Alaska and the Porcupine plateau in the northeast; and peralkaline intrusive complexes in the southwest Alaska Range west of Anchorage, and on Prince of Wales Island in southeastern Alaska. Limited evidence suggests that the heavy REE are associated with deposits that became more highly evolved by late hydrothermal processes.

Jan 1, 2012

By Carl Rampacek

Laboratory and small-scale continuous pilot-plant investigations made at the Tucson Metallurgy Research Laboratory of the Bureau of Mines have demonstrated that the copper segregation process is applicable to the treatment of oxidized and mixed oxide-sulfide copper ores regardless of the gangue constituents. The process comprises heating the ore to a temperature of 750° C. with small quantities- of sodim chloride and coke to produce metallic copper, which then is recovered by flotation. Tests were made on' 23 copper ores of different types containing 0.8 to 5 percent Cu, .The copper recoveries ranged from 73 to 96 percent in concentrates assaying 10 to 62 percent Cu, depending on the grade and type of ore, The direct operating cost for a 1,000-ton-per-day furnace and flotation plant is estimated at about- $3 per ton of ore.

Jan 1, 1960

By Dongjie Zhang, Fengyu Ren, Xudong Li, Yanjun Zhou, Yang Liu, Rongxing He, Jianli Cao

Based on the limiting-equilibrium analysis of roof processive caving in hanging wall caving method and the critical medium column theory, a new model of subsidence prediction caused by sublevel caving mining method was proposed in this study, considering the drawing influence and the dynamic process of filling granular media. Meanwhile, the distribution rules for lateral pressure with different orebody dip were studied under drawing ore, and subsequently complemented the model. This model indicated that the surface subsidence scope decreased as the unit weight of crack rock and the orebody dip increased. In addition, the height of critical medium column showed a decreasing trend as cohesion of rock mass, the internal friction angle and the unit weight of rock mass. Also, the method of predicting the scope of surface subsidence in the Dabeishan Iron Mine was applied. The results showed that the relative errors are less than 9% and the prediction method could be used in practical application.

Feb 24, 2022