Search Documents

By Wayne Taylor, Martyn Dawborn

Simulation modeling of portions of two platinum mines using General Purpose Simulation Software (GPSS/H™) is presented in this paper. Both mines, located in the Bushveld Igneous Complex PIC) of South Africa, exploit Merensky and UG2 reef horizons, which are processed separately and therefore handled individually from the stope face to surface, requiring duplication of storage arrangements and batch operation of transport facilities. The first simulation assignment concerns the upgrading of a shaft system operating exclusively on Merensky ore, to hoist UG2 ore and increase production. The second assignment comprises a simulation of rock flow from the stope face to surface by way of tramming, inclined conveying and vertical hoisting. Development ends and stope boxholes were modeled down to individual hoppers (cars) demonstrating the versatility of the GPSS/H™ language.

Jan 1, 2002

By Anthony W. Wakefield

The paper is intended merely as an introduction to methane hydrates, what they are and why they are important. It does not claim to be a cutting-edge research report, but may be useful for those to whom the subject is unfamiliar.

Jan 1, 2008

By H. Walqui, S. K. Kawatra, C. H. N. Jeltema, T. C. Eisele

"The literature contains many cases where the shape of hydrocyclone efficiency curves vary from the ideal “S” shape. These often appear as changes in slope, or inflections. These inflections can be divided into two categories: “coarse” inflections, which are caused by differences in the density of the minerals being separated, and “fine” inflections, for which there are a number of competing hypotheses concerning their cause. The existing literature addresses either the fine inflection or the coarse inflection, but no studies have reported both types of inflection occurring at once in a single hydrocyclone test. This paper presents hydrocyclone results from both in-plant studies and laboratory experiments that show both coarse and fine inflections. The industrial significance of both types of inflections is discussed. Hydrocyclone efficiency curves show the probability of any given particle reporting to the hydrocyclone underflow as a function of its size. Selectivity functions, S(d), are used to represent the fraction of the feed material in size fraction “d” that reports to the hydrocyclone underflow. Plotting this selectivity function against particle size leads to the standard S-shaped efficiency curve shown in Fig. 1. In the “uncorrected” curve, the tail of the curve does not go through 0%, because a portion of the solids are bypassing classification. This happens as a result of their being carried along by the water, and is most important for the finest particles. The curve can be “corrected” based on the fraction of the feed water that reports to the underflow, represented by the bypass fraction, Rf. The corrected curve then normally passes through 0%, as shown in Fig. 1.The act of correcting the curve shifts the value of the d50 size, which is the size that has an equal probability of reporting to either the overflow or to the underflow. Correcting the curve to account for the bypass fraction makes it easier to compare cyclone performance under conditions that cause the quantity of water in the underflow to change, but that do not alter the actual corrected cut size (d50c).The corrected efficiency curve can be expressed closely by equations such as Plitt (1976):"

Jan 1, 2015

By Colin D. Jardine

Rapidly increasing energy costs and more rigid customer quality requirements necessitate improved control of pelletizing processes. With the introduction of dedicated microprocessor-based controllers, sophisticated control strategies are now possible. A recent application of this technology at Carol Project has resulted in fuel savings, improved pellet quality, and standardization of operating procedures. This was accomplished with no production loss by the use of a "building block" approach to design and equipment selection. Details of this approach and the results obtained are described.

Jan 1, 1982

Exploration of new resources and development of new equipment and designs are an ever changing facet of mining. New equipment to handle specialized operations is being developed and new techniques for its use explored. One such system is reviewed. Another is a potential system for handling the thinner stray coal seams between the more profitable thick seams. The availability of federal coal leases in the West is reviewed and current planning discussed. Gulf Coast lignites have been of much interest in recent months and are overviewed.

Jan 1, 1979

By H. D. Lelono, M. Walden, G. Johnson

3D modelling can be used throughout the mine lifecycle and has proven to be a powerful tool for consultants and mining companies. One of the most significant benefits of 3D models is their ability to enhance collaboration, communication, and understanding between the mine owner, design engineers, and other relevant stakeholders that have a shared interest in responsible mining and site management. Tailings and mine waste management is an interdisciplinary effort that requires effective coordination and communication between a wide range of consultants, operators, and stakeholders alike. The increased emphasis on Environmental, Social, and Corporate Governance (ESG) highlights the importance for mine operators to engage and communicate with all parties involved in the planning, permitting, operation, and closure of mine sites. 3D models are valuable tools that can be used for development of geotechnical conceptual models, allowing for improved design and monitoring of Tailings Storage Facilities (TSFs). A clear conceptual understanding of a TSFs subsurface geology and foundation characterization is essential for proper tailings management, design, and planning. Visualization with 3D modelling can simplify the interpretation of the, oftentimes intricate, mine sight subsurface settings and allows for quick and effective geotechnical conceptualization. 3D models can be used to identify data gaps, optimize field investigations, and streamline the development of numerical stability or groundwater models. They can help communicate the complex nature of subsurface and TSF interactions in a clear, concise, and accurate manner to both technical and nontechnical stakeholders. This paper discusses some of the benefits of 3D modelling in relation to geotechnical analysis for tailings management and provides methodologies for how to improve upon some methodologies that are considered industry standards.

Feb 1, 2023

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By M. Westerstrand

The processes involved in the concentration of magnetite ore with process water as the aqueous medium can have a strong influence on the surface properties of the magnetite particles. In this study, different leaching methods, as well as zeta potential measurements, were used to examine the major easily accessible ions on the particle surfaces and their effect on the surface charge. The results show that the enrichment of elements on the surface of the particles appears early in the refinement process. Ca was enriched up to 15 times and Si up to 50 times compared to what pore water alone would have given. The leaching experiments also showed that the addition of water glass increased the surface enrichment of Si and that the collector might hinder desorption of Ca. An alkali leaching method was evaluated, which showed that Si was much more enriched than S and Cl. Zeta potential measurements on synthetic magnetite particles showed that process water resulted in zeta potentials different from the potentials measured for these particles in aqueous calcium and silicate solutions. Therefore, it is important to consider the complexity of the process water when making predictions about the properties of the particle surfaces in the final magnetite concentrate, which most studies do not. Zeta potential measurements were also used to rule out a strong influence from organic matter in the process water on the magnetite zeta potential.

By Anthony Harding

In a world of technology and electronic communication, it is easy to forget what engineers do best with a problem: sitting around a table, exchanging views and ideas with sketches and respecting everyone?s view. This was the approach adopted in the project to arrive at a solution for the cross passage opening sup-port for the Seattle University Link Extension. Schedule and space constraints usually impede concurrent cross passage excavation and tunnel boring machine (TBM) operation. And where the space is constrained, opening support solutions that maximize available cross sections are of great benefit. While there are a number of solutions that minimize space, some of these solutions can require expensive steelwork and extensive drilling and fixing. However, following a detailed round-the-table discussion of the options and constraints, it was identified that a shotcrete shell would not only limit obstruction of the space during installation, but also permit easy installation, particularly around services, and avoid costly steelwork and drilling and fixing.

By W. Edwin Dill

For the mining industry, the Internal Revenue Code and regulations offer a range of choices in arriving at the allowable depletion. Each case is essentially unique. Two prerequisites can optimize these opportunities: communications between the mining company's tax specialists and its technical staff; and an understanding of IRS definitions. For the latter, a logical starting point is consideration of exploration and development, since they precede production and depletion is unallowable prior to production. Criteria for selecting engineering and accounting options for exploration and development indicate the necessity of interaction between these company functions to achieve the most favorable tax position.

Jan 1, 1982

By D. S. Choi

The paper contains a subsidence measurement taken over a room and pillar panel of a mine located in northern West Virginia. A total of 72 monuments were used to determine a three dimensional view of mine subsidence. In addition, the results of measurements were used to compute ground strains with the use of a numerical model.

Jan 1, 1982

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By Matthew Goff, Russell Lutch

The Great Lakes Water Authority (GLWA) operates the largest regional water authority in the State of Michigan. Two of the tunnels supplying raw water to the system from the Detroit River are the Springwells and Northeast Tunnels. The existing 70- to 90-year old concrete lined tunnels have experienced distress and cracking over their life requiring non-structural repairs to sections of the tunnels. For the repair, an interior stainless-steel segmental liner plate system has been designed to restore the watertight capacity of the tunnel liner and resist the exterior hydrostatic groundwater pressure in a dewatered condition. The team is utilizing a “wet repair” approach to perform the necessary repairs while the tunnel remains fully flooded and operational. To test and validate the tunnel repair approach, a full-scale mock-up of the proposed repair has been performed using underwater equipment and divers.

Dec 1, 2022

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted by-products generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining; (2) dyke construction schedule; (3) size, shape, and location of tailings-cells; and (4) mining and processing production targets. The results show that in creating in-pit tailings-cells designs, decreasing the mining-cells volume and increasing the number of mining-cells improve the net present value of the operation due to increased operational flexibility. The model generated a uniform schedule for ore and practical tailings-cells designs for backfilling activities. Integrating tailingscells optimization into oil sands mine planning and waste management ensures the efficient use of in-pit mined-out areas required for sustainable operations.

Apr 14, 2021

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Robert Stefanko

The most perplexing problem that has confronted mining engineers since the dawn of mining has been strata control. For the purposes of this paper, strata control will be defined as control of ground in the immediate area surrounding the, mine opening. To prevent movement of the surrounding strata into underground mine openings, miners have traditionally relied upon some type of artificial supports placed within the openings and located in a manner determined by trial and error from previous experience. Without the means to measure changes of stress in the supports and within the mine structure itself, an evaluation of the efficiency of the supports and mining system was impossible. Strata control thus remained an art with very little application of science. During recent years a revolution has occurred in mining. The modern mining engineer is contented no longer-with trial and error methods but is utilizing all the technological information at his command to obtain a solution to this age old problem. However, serious problems have arisen due to the lack of certain basic knowledge in three important areas: 1, The original stress distribution within the earth strata prior to mining. 2, Redistribution and concentration of the original stresses with mining activity. 3. The properties of rock that are significant in failure and its prevention.

Jan 1, 1960

By Brian Mangogna, Clay McNail, Weishi Mang, Adam Steimel

Together with innovatively applying modern flotation reagents and developing the breakthrough mill enterprise expert control and operating system, Doe Run Buick Mill constructed an advanced large copper rougher scavenger to process its complex Pb\Zn\Cu ore more efficiently. The scavenger circuit, featuring its own motor control center, air blower, multiple reagent loops and FrothSense+™ camera, operates both mechanically and chemically to maximize copper recovery and under expert control. Such scavenger features can be applied to zinc rougher circuits for all Doe Run mills to maximize Cu recovery during Cu special runs when the zinc rougher becomes a copper rougher scavenger.

Feb 1, 2025

By H. Colijn

The problem of the freezing of moist raw materials, such as concentrates, in railroad cars during winter shipment has been a continuing source of both economic and operational trouble to the industry and to the railroad companies. The difficulties center around the discharging of frozen cargoes into the plant materials handling system. Because of cargo freezing, appreciable delays in car-dumping schedules occur each winter and cause additional expense for demurrage charges and for slowdown of plant operations. In one plant during one winter, a car dumper rated at 40 cars per day could dump only 3 cars per day in bad weather. Delays became so serious one winter, that 500 cars held in the yard became so badly frozen, that they were sent to the southern part of the United States to thaw after they accumulated an average of two months demurrage charges. These delays in car unloading become critical if unit or integral train concept is applied to the movement of raw materials. Anticipated savings in transportation costs through better equipment utilization are largely based on rapid loading and unloading cycles of whole trainloads. If freezing problems cannot be adequately solved, unit train operations cannot be operated to achieve the potentially large reductions in transportation costs. The freezing problem may tend to become even greater in the years ahead, because the unit train concept will allow the trains to run faster and consequently the heat loss will be accelerated due to the larger heat transfer coefficient. A compensating factor, however, will be the shorter travel time. Further, the sources of raw materials being mined are located farther north than before and the ambient temperatures during transit are going to be lower.

Jan 1, 1976

By Henk L. C. Meuzelaar

Most of us are aware of the relationship between the golden-yellow resin spots on Upper Cretaceous Wasatch Plateau coals and fossil tree resins (?amber?). Nevertheless, confusion remains about the exact chemical composition and structure of commercial coal resin preparations as well as their observed heterogeneity. In order to arrive at a more detailed chemical description we need to distinguish between micropetrographic, organic geochemical and process technological definitions of coal resins, which may include substantial quantities of constituents unrelated to fossil tree resins. New information on composition and origin obtained by Curie-point pyrolysis/evaporation in combination with isobutane chemical ionization mass spectrometry, as presented in this paper, points to the presence of four more or less distinct resin components: (1) a sesquiterpenoid polymer; (2) sesqui-and triterpenoid monomers and dimers; (3) a suite of triterpenoid alcohols, ketones and acids; and (4) a series of increasingly aromatized hydrocarbons with naphthalene and picene type skeletons. Moreover, a strong similarity is found between the composition of recent Dammar resin and fossil Wasatch Plateau coal resins. Some of the technological implications of these findings and the consequent need for a more precise chemical definition and nomenclature are discussed.

Jan 1, 1990

By G. S. S. Raman, M. S. Klima

The effects of pressure and cake thickness were studied using a split-plot design for pressure filtration of a fine refuse slurry obtained from a bituminous coal preparation facility. Pressure filtration offers the potential to significantly reduce the moisture content of the fine refuse stream with the addition of little to no flocculants, thereby minimizing the volume of refuse stored in impoundments and providing a recycle water stream for use within the plant. Experimental results showed that the final cake moisture decreased with increase in pressure and decrease in cake thickness. In addition, specific cake resistances calculated for the various tests indicated an increasing trend with increasing pressure and decreasing cake thickness. With increase in cake thickness, an increase in cake moisture and the weight of solids deposited in the cake was observed. An ANOVA analysis indicated that both cake thickness and pressure significantly affected the cake moisture, while only cake thickness statistically influenced the weight of solids in the cake. A regression model was developed with an R2 value of about 0.99 to relate cake thickness, the single largest statistically significant factor, with the weight of solids in the cake. Filter capacities were calculated in terms of the solids deposited per unit time based on a product specification of 25 percent cake moisture, and it was observed that the thinnest cake had the highest filter capacity.