Search Documents

By J. J. Carlson

Studies were carried out to determine whether filtration rate changes observed in an iron ore concentrator were due to variations in particle shape. It was confirmed that ores mined from different locations differed in filtration rates by as much as 60%. However, when image analysis was used to quantify the shapes of the individual particles in the filtration feed, it was found that the particle shapes showed almost no variation, and the shapes did not correlate with the filtration rate. It was also determined that the filtration rate variations were not caused by changes in particle size distribution. These results suggest that the differences in filtration rate are due to factors other than size and shape, such as surface chemistry.

Jan 1, 2008

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By A. Founie

The United States continues to be the world’s leading producer and consumer of diatomite. Production of diatomite in the United States during 2004 was estimated to be 635 kt (700,000 st). This was a 2-percent increase from 2003. The value of processed diatomite in the U.S. was about $164 million in 2004. Production was from six companies with 13 processing facilities in four states. Nevada and California were the principal producing states. They accounted for about78 percent of the U.S. production during 2004. U.S. diatomite exports were about 136 kt (150,000 st). Imports were negligible.

Jan 1, 2005

Equipment-washing facilities at Freeport-McMo-Ran?s Sierrita Mine in Arizona produce a mixture of oil and water that was difficult to dispose of easily or cheaply. However, after some changes in the facility, waste oil is now used as part of the mining process. Freeport-McMoRan Copper & Gold Inc., head-quartered in Phoenix, AZ, operates copper, gold and molybdenum mines. It is the world?s largest producer of molybdenum. Heavy equipment used at the mine is hosed off periodically in the wash bay. The dirty water and oil mixture drains into the sump next to the bay. Oil was manually collected for disposal. This was a tedious and dirty process Mine managers sought a more efficient method of removing the oil. Instead of spending the time and effort skimming the tank with vacuums or sorbents, they enlisted the help of Abanaki Corp., manufacturer of the Model 4 Oil Grabber. Engineers designed the sump to utilize prevailing winds to blow the oil to one corner. This was the ideal place for the Abanaki skimmer. The skimmer removes the oil and discharges it into a plastic storage container. ?This reduces the time needed to keep the area clean, and the staff can focus on cleaning the equipment rather than worrying about the oil,? according to Jay Salerno, construction manager at the Sierrita Mine. Salerno is considering adding an optional oil concentrator to the skimmer to make the process even more efficient. The concentrator would remove any water picked up by the belt and return it to the sump, leaving nearly pure oil for disposal. Because the mine is located in the Sonoran desert, most of the water evaporates in the hot, dry air and is not reused.

Jan 1, 2009

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By Raymond W. Henn

The 30th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 22-26, 2009. The field demonstration portion of the course was conducted June 25, at Hayward Baker, Inc.?s yard in Broomfield, CO. The full-scale field demonstration annually presents many different types of drilling equipment being operated as well as various grouting methods being performed under different field conditions. As part of the field demonstration, the class is shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and measured conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results. The goal of the sand column demonstration is to show the students the effect of the water cement ratio and the use of admixture as well as the fineness of the cement, portland versus ultrafine, used has on the engineering properties of the grout and the grout?s vertical permeation through the sand. Test results for the demonstrations conducted in 1999 and for two separate demonstrations, one at the grout course and one at Geo Denver, conducted in 2000 were published in the 2001 proceedings of the Rapid Excavation and Tunneling Conference (RETC) (Henn et al. 2001). The test results for the 2002 and the 2003 demonstrations were published in the 2005 proceeding of the RETC (Henn et al. 2005).

Jan 1, 2009

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity

By A. Anani

The need to optimize surface mining operations has led to the use of discrete event simulation (DES) modeling of truck-shovel systems. Often, these models assume truck cycle times are independent and identically distributed (iid) random variables, although, with significant bunching on the haul routes, this may not be valid. The objective of this paper is to present a methodology to (i) account for truck bunching due to slow trucks; and (ii) test for cycle time dependence (i.e. whether truck cycle time data is iid or not). We built a DES model that accounts for bunching due to a slow truck(s) and used the cycle times as data for further analysis. We then tested for cycle time dependence using Pearson correlation coefficients. The results show significant correlation of truck cycle times for different number slow trucks, with variable speeds. Assuming iid in modeling results in over-estimation of productivity and the uncertainty surrounding it. The over-estimation of uncertainty is pronounced when the relative difference in truck speed increases. The confidence interval of the means of truck loads/shift decreases with increasing number of slow operators. This work extends the usefulness of DES in truck-shovel applications.

Feb 27, 2013

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

By Robin J. Batterham, Dave J. Robinson

The history of mineral processing in general and flotation in particular is long and has always been tied to mining methods of the day. Building on the ever-improving fundamental understanding of the underlying science, the most significant trend in flotation has been the putting into practice the learnings from trailblazers such as Professor Fuerstenau that has given the confidence that enabled an ever-increasing scale of operations. There is, however, doubt this ongoing trend is enough to maintain the economics against global trends such as that of falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. In addition, we see that globally, the social license to operate for mining (and hence mineral processing) is far from secure and, at the very least, is under much more rigorous scrutiny. In this paper, we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10–20 years but in the meantime, the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation, as we know it, will change significantly.

By I. Yildirim

Free energy of interaction between particles in water can be calculated if one knows the values of appropriate interfacial tensions, which in turn can be determined from the surface free energies of the particles involved. The latter can be determined using the Van Oss-Chaudhury-Good (OCG) equation. This method requires the measurement of contact angles of well-defined liquids on the surfaces of the particles of interest. In the present work, the contact angles were determined using heat of wetting, capillary rise, and thin-layer wicking methods. The results are compared, and the utility of the surface free energy data obtained from the contact angles are discussed.

Jan 1, 2002

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By Jerry C. Tien

Mining in China dates back at least 4,000 years. Today, with no less than 103,000 metal/nonmetal mines and between 40,000 to 80,000 coal mines, China’s mining industry is undoubtedly the largest in the world. Despite improvements in recent decades, seemingly endless mining accidents continue to make the news. Official coal mining deaths were 6,702 in 2003, and 6,027 miners died in 2004; actual figures may be much higher. Added to these were the 2,699 deaths in the metal and nonmetal industries. Most of these accidents were due to CH4 (methane gas) explosions and fires as a result of inadequate mine ventilation de-sign or practices. A good portion of these accidents occur in small, privately run and often technically illegal mines. During the past 10 years, the Chinese government has attempted to crack down on small and often technically illegal mines without much success. The number of accidents and associated fatalities has not significantly reduced. However, there appears to be a new urgency in China’s efforts to step up mine safety in the country. After its worst reported mine disaster in more than a half century, the government quickly paid reparations to families, suspended high-level officials in charge and announced additonal reforms. One of those was the elevation of the central government’s work safety office to cabinet-level status. There has been increased transparency in reporting and investigation of mine accidents and disasters in recent years. There has also been an increase in public criticism by labor leaders concerning the neglect of mine workersafety.1 This article examines the causes of China’s many mining accidents, current legal and enforcement structures, respective mining health and safety related laws and regulations, recent mining industry developments and the latest effort to curtail small mining operations.

Jan 1, 2005

By Judy B. Jones, Bradley A. Crenshaw, Theodore DePooter

This paper reviews groundwater issues leading to a secondary grouting program at the Chattahoochee Tunnel that was implemented subsequent to the contact grouting program. The secondary grouting program was developed based on infiltration data, geology, and testing programs. This paper includes a brief description of the geological features encountered, as well as describing the grouting program. The success of this grouting operation has been quantified by several methods, and is presented to help others project the costs and benefits of this type of program. Review of initial results and refinements of techniques are also discussed.

Jan 1, 2005

By Günter Huber, Bruno Mattle, Helmut Westermayr, Daniel Spöndlin, Max John, Nejad Ayaydin

PROJECT DESCRIPTION Alignment The Strenger Tunnel forms part of the S16 four-lane expressway between Landeckand Bludenz. The construction of this important East-West connection started in 1973with the Arlberg Road Tunnel as its key constituent. Beginning in 1992, solutions for the section between Pians and Flirsch were investigated. Efforts to conserve nature and to avoid potential avalanche and landslide areas led to a solution detouring the villages in the Stanz valley. The starting points were predetermind by the intersections at Pians in the East and at Flirsch in the West. As a result of the expected traffic load and the comparatively high gradient of 2.9%, both one-way, two-lane tubes were constructed at once. The north tube is 5.851 m long, the south tube 5.775 m, see Figure 1. Layout of Tunnel Cross-Section The tunnel cross-section was determined by 2 × 3.75 m wide, 4.70 m high roadways, two sidewalks and sufficient space for two fans above the clearance

Jan 1, 2005

By Gerald C. Smith

Introduction Newmont Mining Corp.'s Carlin Gold Mining Co. mines gold ore and waste material from four open-pit mines in Northeastern Nevada. Combined production rate is 24.5 Mt/a (27 million stpy). The company is producing gold bullion from the 2.4 kt/d (2600 stpd) Carlin Mill No. 1. and the 2.3 kt/d (2600 stpd) Maggie Creek heap leaching plant. In August 1985, the 6.3 kt/d (7000 stpd) Carlin Mill No. 2 at Gold Quarry came on-line. The total combined throughput of 11.2 kt/d (12,000 stpd) will make Carlin Gold Mining one of the largest US gold producers. Feasibility studies are underway to increase the total gold out-put from Gold Quarry. This will be done by adding a continuous dump-leaching process that will recover gold from lower grade ore. History In 1961, Newmont exploration geologists located claims in the Lynn Creek mining district near Carlin, NV. An exploration drilling program revealed significant gold mineralization. A stepped-up drilling program revealed an ore body with an estimated 10 Mt (11 million st) of ore containing 109 t (3.5 million oz) of gold. Test results in 1963 allowed metallurgists to develop the flowsheet and design for a 1.8-kt/d (2000-stpd) countercurrent decantation (CCD) cyanide plant. Carlin Gold Mining Co. was formed to operate the property. Carlin purchased its first mining equipment in 1965. This consisted of two Bucyrus-Erie 2.7 m3 (3.5 cu yd) shovels and nine 27.2 t (30 st) Wabco Haulpak trucks, two Inger¬soll-Rand track-mounted drills, one Chicago Pneumatic T-650 rotary drill, one rubber tired Michigan 280 dozer, one Caterpillar D-8 36A track dozer, one Caterpillar 16 motor grader, and the necessary ancillary equipment. The fleet was capable of mining 3.2 Mt/a (3.5 mil¬lion stpy) working two eight-hour shifts, five days a week. In 1967, one P&H 1500 3.8 m3(5 cu yd) diesel electrical shovel and three 59 t (65 st) Dart trucks were added to the fleet, along with a Chicago Pneumatic rubber tire mounted rotary drill. This equipment addition increased the mining capabilities to 5.7 Mt/a (6.3 million stpy). Three separate pits, the Main, East, and West, within a 1.6-km (1-mile) radius of the Carlin mill were being mined. The crew consisted of 46 hourly men and three supervisors. This equals 497 t/ total hourly manshift (548 st) or 407 t/total manshift (515 st). Rising gold prices in the early 1970s allowed lower grade deposits to be mined at greater distances from the mill. The Boot-strap pit, 19.3 km (12 miles) north of Carlin, was started in 1973. Two Hough 45.4 t (50 st) front-end loaders, four Wabco Haulpak 45.4 t (50 st) trucks, and a second track type D-8H dozer were added. The higher grade ore was trucked to the Carlin mill using three

Jan 11, 1985

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By Peter J. Tarkoy

A great deal of attention has been directed toward the complexities and inadequacies of exploration and pre-bid geotechnical information for heavy construction projects, differing site conditions, and the adversary relationships which generally develop as a result. The adversary position has been maintained at all cost. The solution is simple, if not easy. The solution requires strict and equal adherence to given principles by all parties involved, throughout the life of the project, from conception to completion. It is necessary to review and redefine some basic concepts, without value judgements, from a context of getting the job done. In a recreated context, the role of truth, judgement, responsibility, and integrity, in exploration, engineering design, construction estimating, and project construction, will be examined. It is suggested that anticipated geotechnical conditions be defined unconditionally. The alternative choice is to give the bidder the opportunity of making the interpretive judgements based on geotechnical data. Similarly, a unilateral method of establishing encountered conditions that are agreeable to both owner and contractor, must be outlined prior to contracting. As anticipated and encountered conditions are firmly and accurately established, significant differences can evaluated based upon limitations specified in the contract documents. Impact of differences on project costs can be fixed by pre-defined methods.

Jan 1, 1983

By Dexter C. Hatch

At MacIntyre Development of the National Lead Company, Taha s, New York,, the flotation plant was set up to recover ilmenite from the finer size fraction of the ore that cannot be efficiently treated in the main gravity-magnetic separa¬tion process. It was later expanded to handle the reground middlings from the tables wetherill magnetic separators. The ilmenite-magnetite ore is ground to minus 20 mesh in five 6 x 12 ft. rod mills in closed circuit with DSM screens. The minus 20 mesh screen undersize is pumped to four parallel sections each consisting of two rougher wet-magnetic separators and one cleaner separator for magnatite removal. The screen undersize from the fifth section is distributed to all four sections. The magnetite removed in the roughers is pumped back to the cleaners and the cleaner magnetite is dewatered in rake classifiers and carried by belt to the winter plant or the stockpile area. The nonmagnetic sands from rougher and cleaner magnetic separator are sized for table feed in eight pocket hydraulic sizers. The slime overflows from the Crocketts, the sizers, and the magnetite rakes are collected and pumped to three-inch cyclones for thickening and desliming. The cyclone underflow is the principal flotation plant feed.

Jan 1, 1962