Search Documents

By W. C. Baver

Even before the energy crisis developed in the early '70's, considerable research world-wide was being directed towards the development of schemes to both reduce the energy requirements and to reduce air pollution emissions associated with the manufacture of glass. In many cases the sought-for solutions would benefit both objectives. If, for example, the glass batch could be consolidated into such compact forms as briquettes or pellets, they could be preheated in a moving-bed heat exchanger with the high-temperature exhaust gases from the glass furnace. Lower furnace temperatures would thus be possible with a corresponding reduction in heat losses and total fuel consumption. Moreover, the lower temperatures would also reduce the amount of nitrogen oxides generated in the furnace and emitted to the atmosphere. Many tests on consolidated glass batch have been run in many countries. In some cases, extended tests on production furnaces have also been included in the programs. For various reasons, however, none of these has proved to be economically attractive. The current, but temporary lull in the rapidly rising cost of energy which has been with us in recent years, has reduced the push for research for energy saving means for melting glass. A few of the current programs will be discussed. Since raw material requirements, primarily physical in nature, are affected by some of these schemes, these will also be considered.

Jan 1, 1986

By Véronique Falmagne, Chantale Doucet, Thomas Côté

Production began in the Deep 1 zone of Goldex mine in 2017 at a depth of 1,200 m. Stope dimensions are 50 m high by 22 m wide (along strike) and the panel thickness varies between 22 to 35 m. The Deep 1 orebody is 350 m high by 400 m along strike and 200 m from hanging wall to footwall. The mining method is longhole with paste backfill with a three dimensional primary/secondary sequence advancing upwards in a typical chevron approach and retreating from hanging wall to footwall in a V-shape from a central panel. Mining at a depth of 1,200 m in massive granodiorite brings challenges related to seismicity.

Apr 26, 2022

By Adam Bedell, Paul Derby, Brad Crenshaw

Modified contact grouting was introduced almost 15 years ago as a methodology combining traditional contact grouting and consolidation grouting to address groundwater infiltration into hard rock tunnels that utilize cast-in-place concrete as permanent tunnel support. This process has been used on additional tunnels (since initially presented) as a measure to mitigate both groundwater infiltration and exfiltration. During this time, self-sealing grouts have been developed and have been added to the process to further reduce groundwater infiltration that occurs through cracks and discontinuities within the concrete liner itself. This modification is presented and additional results from the grouting process are discussed.

Jun 13, 2021

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method tradition-ally solves each mesh equation by an approximation during each iteration. It is thus interesting from both theoretical and computational viewpoints to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation, which has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the two solutions.

Jan 1, 1997

By Henry R. Colen

When we were asked to prepare a paper on gold to be part of the Economics of Precious Metals session, our immediate thought was that we should address the question of supply. Are the existing mines of the world capable of filling the demand for gold? We recognized that gold does not conform to the normal pressures of supply and demand. Major new sources of production and increased sales might have a very short term effect and depress the price but this does not last very long. Those forces that affect gold prices are very different from the ones economists normally deal with. Factors such as mass psychology, political tensions and fear are certainly more important to the gold price than supply and demand in today's world.

Jan 1, 1981

By T. G. Carnahan

The U.S. Department of the Interior, Bureau of Mines, performed a laboratory-scale investigation of technique for recovering silver from pregnant solutions generated in the hydrometallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This provides a means for recovery and simplified reduction of accessory silver to metal from ions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to-92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

By V. Price

Abstract: Action of certain strains of bacteria has been implicated as a significant factor in the oxidation of ore deposits. Other bacteria are thought to be significant in the formation of syngenetic sedimentary ores and in supergene enrichment processes. A normal soil/ground-water regime provides all of the necessary pH and Eh conditions for several groups of bacteria which influence the sulfur cycle in nature. Limiting concentrations of nutrients such as sulfate ions can determine whether a particular microbial species is active at a given place. In the present study, ground water was analyzed from a mineralized area and from a presumed barren area. Trace metal content of the ground water gave no well defined clue as to the presence of a sulfide ore deposit. Sulfide producing bacteria (presumably sulfate users) were found in water from about 50% of wells sampled in the mineralized area and in about 30% of samples from the barren area. These bacteria are readily detected and may provide a useful tool for regional geochemical recon-naissance. Bacterially produced sulfide ions can remove metals such as copper and zinc from solution thus complicating the interpretation of hydrogeochemical prospecting.

Jan 1, 1972

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

By S. K. Kawatra, S. J. Ripke

Iron ore concentrates pellets are currently in duration heat hardened (sintered) under oxidizing conditions. Pellets produced from magnetite ore concentrate are completely oxidized during induration and finish as hematite pellets. These pellets then require a blast furnace to reduce the hematite to metallic pig iron. Partially reduced pellets would save energy and fuel during transportation and further reduction. It has been stated in the literature “the most important single factor responsible for the development of strength in fired magnetite pellets containing no additive is the oxidation of the magnetite to hematite and the subsequent recrystallization and grain growth of this constituent.” However experiments shown in this paper reveal that oxidation is not necessary to produce high-strength pellets. Magnetite concentrate pellets developed similar strength when indurated at 1350°C under either oxidizing (air) or inert (argon) atmosphere; the pellets sintered under argon remained magnetite. In addition, magnetite concentrate pellets indurated under reducing (CO) atmosphere also remained as magnetite, but required induration temperature of approximately 150°C less than the other pellets.

Jan 1, 2003

By Jerry Grott

Southwest Salt Company is solution mining the Luke Salt Body of probable late Miocene age. The discovery hole, from which the first core was recovered, was drilled in 1968. The deposit was encountered at a depth of 880 feet, and the bit was still in salt at the bottom-hole depth of 4,500 feet. The solar ponds, developed on land formerly dedicated to agriculture, have an annual capacity of about 90,000 tons. Because land values are very high, mining rates and procedures are governed by the need for near-saturated brine to minimize land requirements. Because of the frequency of dust storms, the salt operation uses a unique wet-harvesting method. Most inventory is kept in the ponds under brine and harvested only a few days before shipment. Studies of the nature of crystal growth and the distribution of windblown and brine impurities led to the development of procedures for processing salt of high chemical purity and low insolubles content. Chemical purity exceeds that of most salt produced in fuel-fired evaporators. Salt is shipped from Phoenix as tar east as west Texas and as far west as central California. Occasional shipments have been made to Hawaii and Alaska.

Jan 1, 1987

By W. W. Wen

Approximately 3 percent of the raw coal processed in U. S. Steel coal-preparation plants ultimately reports to slurry- tailing disposal. The usual disposal method is to pump the refuse slurry containing the minus-48 mesh (300 µm) refuse into dams or impoundments that are constructed of the coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, West Virginia and the sliding failure of a coarse refuse pile at Aberfan, Wales, England, resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of Federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal areas. As a consequence of these regulations the use of the landfill/impoundment method of disposal became in some cases economically urlfeasible or technically impossible. U, S. Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, Portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition it was decided to study the stabilization of fine-coal-refuse slurry through use of cement-type additives.

Jan 1, 1979

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By Mark H. Johns

Leaching of waste material at Kennecott's Chino Mines Division at Santa Rita, New Mexico, has been accompanied by increasing difficulty in circulating leach solutions through the dumps. As a means of recognizing existing problems and considering alternative applications of the leaching concept, a leaching research program was proposed which could be applied to a specific, typical waste dump. Conclusions derived from the area could then be applied to other leaching areas at Chino. Associated with the program was an evaluation of the physical characteristics of the area using Chino's drilling and radiation logging techniques.

Jan 1, 1970

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime's shares and manages and operates the mine on Prime's behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999

By Roger N. Miller

Talc mining in Vermont has in recent years undergone a progressive change in mining methods and in mining equipment. Underground mines have been phased out except in special circum- stances, and continuous mining machines (CMM?s) have replaced conventional drill/blast mining systems. Talc mining in Vermont began in the late 1800?s, and has continued without interruption to date. Beneficiation (flotation) has been applied since the early 1930?s, and has provided special products for toiletries and other markets. At the present time, there are two active companies that have evolved from the cumulative absorption of nearly ten smaller operations.

Jan 1, 1984

If a fire occurs outby an underground coal mine section, the immediate safe evacuation of miners from the working section should always be the first action during the rescue operation. Unfortunately, in many cases, the escape-ways (escape routes) dedicated for miners' evacuation are contaminated with fire byproducts from adjacent entries. The purpose of this paper is to present the ventilation control process that will maintain the escape-way free from contaminants and available for travel. Several scenarios in a different section on ventilation system arrangements are analyzed, discussed and presented. To perform these studies, the author used a mine-fire simulator, which provides a dynamic (in real time) representation of the fire's progress and also gives a display, a color-graphic visualization, of the spread of combustion products throughout the ventilation system. Presented and discussed in this paper, also, are ways in which the mine-fire simulator can be used as a training and teaching tool for miners and, particularly, for ventilation and safety personnel.

Jan 1, 1993

By J. M. Mutmansky, B. Kolonja

A PC-based simulation model using the software packages SIMAN and CINEMA was developed to simulate and animate truck-shovel operations. The model is capable of simulating one mathematical dispatching strategy using linear and dynamic programming and six heuristic dispatching strategies. Data were collected from an actual operating mine through time studies and analysis of historical records. Statistical analyses were performed, and appropriate theoretical distributions were fitted for various time events in the truck-shovel cycle. The model was then applied to study overall impact of these dispatching strategies on constrained and unconstrained mine productivity. The simulation/animation model developed in this study seems to be an efficient planning tool for choosing optimal fleets and finding an optimal dispatching strategy to produce an equilibrium between the quality and quantity of production.

Jan 1, 1995

By D. Brabec

One of the analytical problems in exploration geochemistry is the choice of a method of sample attack which would be rapid, simple and reliable in terms of precision and discrimination between different concentration levels of elements sought. The wet sample attacks currently used in analysis of silicate rocks vary from total decomposition to leaching by weak extractants. The total decomposition of such materials is usually achieved either by alkaline fusion or hydrofluoric acid attack. The first method requires the use of platinum vessels which is both expensive and slow for batch operation. The second type of attack is more widely applied in rock geochemistry1, but it is still relatively slow for exploration purposes and requires extra care (especially when hydrofluoric acid is used in mixture with perchloric acid). Considerable improvement in speed can be achieved by using the sample attacks which release only part of the metal present in a rock.2,4 One of such attacks is the leaching of pulverized rocks by hot aqua regia.3 Another technique widely used in geochemical prospecting involves fusion of the samples with potassium pyrosulfate (or bisulfate) followed by an acid leach of the malt .5 One of the advantages of these techniques is the use of glassware in decomposition stage which considerably increases the analytical productivity. It should be noted that partial chemical attacks tend to extract from a rock mainly the non-silicate metal which may give results more significant for exploration purposes than the analysis for total metal.

Jan 1, 1970

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991