Search Documents

By Paul H. Muller

The configuration of remote seal DP cells for specific gravity measurement is described and the calculations for calibration are presented. The error induced by ambient temperature change is investigated as it relates to capillary dynamics and electronic considerations. Instrument specifications are discussed in the light of accuracy requirements and the calculation of error vs. ambient temperature is described.

Jan 1, 1984

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By J. J. Kellar

The near-infrared (NIR) (12,000-4,000 cm-1) region of the electromagnetic spectrum, between the mid-infrared and visible, has often been viewed by spectroscopists to be of limited utility. This is unfortunate, and recently the use of the NIR has increased greatly, primarily for the quantitative analysis of food and agricultural products. However, many other areas of application of NIR spectroscopy remain unexamined. In this paper a novel use of NIR in the area of flotation chemistry is demonstrated. Specifically, it is shown that NIR/Internal Reflection Spectroscopy (IRS) can be used to quantify collector adsorption reactions in-situ.

Jan 1, 1990

By L. Rintala, P. Latostenmaa, T. Kalliomäki, O. Forsén, I. Lehtiniemi, M. Lundström, J. Aromaa

Conductivity is a typical physico-chemical property that has a substantial effect on electrical energy consumption in the electrorefining process. The objective of this study was to examine the validity of regression models predicting the conductivity of industrial copper electrorefining electrolytes. The models were based on data measured with synthetic solutions on a laboratory scale. The variables included in the models were temperature and the concentrations of copper, nickel, arsenic and sulfuric acid. Both first-order and combined effects of the variables were investigated. The measured data were analyzed using MODDE 8.0 modeling and design software. The validity of the models was investigated by comparing the predicted values with tankhouse conductivity measurements taken at the Boliden Harjavalta Copper Refinery in Pori in Finland. During the tankhouse tests, the conductivity and temperature of the industrial electrolyte were measured, and the composition of the electrolyte was analyzed. The measured conductivity values were compared with the predicted conductivities calculated using the developed models. The conductivity model developed in this paper was shown to be more accurate than previous models and suitable for industrial use.

By James H. Barks

Commercial development of the mineral resources of southwestern Missouri began about 1850 and spread into southeastern Kansas and northeastern Oklahoma, forming the Tri-State Mining District with Joplin as the urban center (fig. 1). The value of the Tri-State mineral production from 1850 to 1950 exceeded one billion dollars, and until 1945 the region was the world's leading producer of lead and zinc concentrates, accounting for one-half of the zinc and one-tenth of the lead produced in the United States (Gibson, 1972 1). By 1950 most of the rich ores had been extracted, and mining and milling operations declined during the 1950's and ceased in the 1960's. The sulfide minerals, mainly galena and sphalorite, were mined from cherty limestones at depths of 25 to 75 m (meters). Crude ores were brought from the mines to the surface where they were milled into lead and zinc concentrates. , Barren rock was discarded in piles while the ore-bearing rock was crushed and ground into fine gravel. The minerals were separated from the rock by a jigging process and the tailings were skimmed off and discarded in large piles. Ground-water flooding of the mines was controlled by constant pumping. When pumpage declined in the 1950's and 1960's tile abandoned mine drifts and shafts filled with water. At present (1977) numerous tailings piles and flooded mines remain as visible evidence of the mining era and as a threat to the quality of ground and surface waters of the area. In 1976 the U.S. Geological Survey in cooperation with the Ozark Gateway Council of Governments made a study of the effects of the mines and tailings piles on water quality in the Missouri part of the Tri-State District. The study area covers approximately the southwestern quarter of Jasper County, an area of about 725 km2 (square kilometers), and is bounded by long 94 o 15' w.' and the Missouri-Kansas state line, and lat 37 o 15 N., and the Jasper-Newton County line.

Jan 1, 1977

By Donald G. Foot

The Bureau of Mines, U.S. Department of the Interior, devised a direct flotation method for treating low-grade carnallice (KC1.MgC12. 6H20) and sylvinite (a mixture of KC1 and NaC1) ores characterized by a high content of water-insoluble impurities. The procedure consists of (1) flocculation-depression of the insoluble slimes, (2) decomposition leach (carnallite only), (3) potash rougher, cleaner and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity of removing the water-insoluble slimes by mechanical or flotation desliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumptions. The direct flotation method recovered 81.6% of the solid-phase KC1 from carnallite ore and 79.7% of the KC1 from sylvinite ore in final products containing 60.5% and 60.9% K20, respectively. A flowsheet incorporating the described flotation procedure is presented.

Jan 1, 1981

By Dipl. -Ing. Mertens

Gentlemen: I am pleased and regard it as a priviledge to give you a report on rapid roadheading with heading machines in the coal mining industry of Western Germany. Importance of Heading Operations in the West German Coal Mining Industry Every year about 770 km of headings are driven In the seams of the West German coal mines, most of them gate roads, the rest rise headings, to open new faces. In thick seams the heading operations are carried out entirely in the coal, in thin seams the country rock has to be ripped. The total length of 770 km corresponds to a rock volume of roughly 9.5 million m3; this figure underlines the importance of the heading operations in the coal mining industry of our country.

Jan 1, 1970

By M. S. Riyazulla

The Hutti greenstone belt comprising predominantly of low-potassium tholeitic basalt has undergone regional metamorphism of a transition zone between greenchist to amphibolite facies. The important mineral constituents of the volcanic suite are amphibole and plagioclase which appear to be the product of regional metamorphism. These minerals have been recognized as the main indicators of metamorphic temperature and pressure. With a view to understand the P-T conditions of metamorphism of the belt, electron microprobe studies were carried out on amphibole and plagioclase and the chemical data was used to decipher the metamorphic conditions. The results obtained indicated a metamorphic temperature of about 6000 c and pressure of 5 kbs. for the Hutti greenstone belt.

Jan 1, 1996

By James M. Barker

Marketing is the linchpin of the industrial-mineral (IM) industry. Without markets and consumers for IM products, all other associated IM activities are superfluous. The simple existence of an IM deposit does not mean that it can be exploited. A dynamic interaction between exploration (geology), mining, processing, transport, marketing, sales, and consumers is required for profits. Geology dictates the existence of a deposit, but markets dictate its development, and transportation provides the connection. This is true to such an extent that marketing commonly is called the exploration phase of IMs. Marketing is strategic and includes long-range market-development and planning activities, whereas selling is tactical and more focused on day-to-day consumer interactions. Each will help the other when properly done. Many producers of IMs have failed because of inadequate marketing skill, information, and practice. Over many years at the Montana Bureau of Mines, the many developers seeking technical assistance to find an IM deposit, but who had no marketing plan, always failed. In contrast, the few who sought assistance first on marketing, with the IM deposit to be found later, always succeeded (Richard Berg, personal communication, 1998). Marketing has many facets helped by geologists who must be aware of what marketing is attempting to do. A geologist needs to understand many aspects of IMs: location (deposits, plants, consumers), processing (specifications), transportation (truck, rail, barge, ship), competition (local, regional, national, international), substitutes, pricing, and new developments and market forces of all kinds. Some needed skills are not taught formally to geologists, so well-rounded self-education and on-the-job training are the way a geologist normally enters into IM marketing. The IM geologist generally is associated with marketing either by helping to prepare a market study or by acting on the results of one. Preparing a market study is a two-part process. The first part is relatively simple but requires a time-consuming collation of data into an IM survey (mostly past-and present-oriented). The more difficult and much more important second part entails expanding the IM survey into a market evaluation (mainly future-oriented) that emphasizes forecasting, timing, location, and specific products. A market evaluation generally boils down to formulating the right questions to ask of the right persons. One very good question to ask is, "What could be the market for this specific IM?" while thinking for yourself without excessive recourse to gossip, rumors, promoters, developers, or (at times) IM experts. The evaluation must prove that market potential exists and suggests a marketing plan. Effective marketing is an ongoing process, with the initial marketing plan modified over time, using wide and continuous input to avoid tunnel vision. Industrial-mineral markets are based either on commodity (lower-priced, basic-processing) minerals or specialty (higher-priced, value-added) minerals. IM marketing methods are either product-driven (commodity minerals), a more traditional approach, or market-driven (specialty minerals), but these are neither mutually exclusive nor is one always better than the other. Focusing too much on specialty minerals can lead to problems. A blend of commodity products with specialty products commonly lowers risk and enhances long-term profits. The highest profits occur in specialty minerals at the cost of higher risk and complexity and require intelligent marketing, versatile technical services, and creative research and development. Industrial minerals are best served by an industrial-marketing approach rather than a consumer approach. Modern industrial marketing emphasizes the consumer using the "marketing concept." The marketing concept focuses all management and operational activities on total consumer management and satisfaction similar to the total quality management approaches to excellence.

Jan 1, 1999

By B. Andersen, P. Somasundaran

An accurate knowledge of the interactions among mineral particles and between such particles and dissolved and precipitated species is important in developing efficient separation processes. In this investigation, interactions relevant to dispersion and selective reagent adsorption (the two main prerequisites for selective flocculation) within Florida phosphatic clay Waste were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slimes were due to unselective polyacrylic acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Al and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. A further increase in the separation of natural slimes is most likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1994

By Jr. Winters

The United States continues to be the largest producer and consumer of copper in the world. Table 1 on the following page shows several production statistics for 1974, the most recent year which the non-communist world copper industry might consider a good year, and for 1976 and 1977. In 1974 an estimated 24 percent of the non-communist world's newly mined copper was mined in the United States, and. 87 to 89 percent of that was from the western porphyry coppers. In 1976 U. S. new mine production was down to 22 percent of the non-communist world's newly mined copper, and the percentage of U. S. new mine production supplied by the porphyry coppers had risen to 89 to 91 percent. In 1977 the statistics remained the same as in 1976. U. S. porphyry copper production represented about 65 percent of U. S. refined copper consumption in 1974, rose to 75 percent in 1976, and dropped back to 61 percent in 1977 as imports of foreign copper into the United States began to swell.

Jan 1, 1978

By Paul H. Johnson

A field investigation was undertaken to study some of the. chemical and hydrological aspects of leaching an impermeable copper sulfide waste dump. Samples, obtained by means of a Becker pneumatic drill from Kennecott's Chino "J" dump, near Silver City, New Mexico, were analyzed for their moisture and soluble-salt content, Fe +2 , Fe +3, Cu +2 , and H in their interstitial solutions and non-water - soluble Fe, Cu, and S in their rinsed residues. Conclusions were drawn from these data concerning the overall chemistry of impermeable-dump leaching and the hydrological characteristics of the dump.

Jan 1, 1970

By Richard W. Cannon

INTRODUCTION The authors, by means of this paper, will attempt to show the role of Induced Polarization and Resistivity surveys in the discovery of the orebodies of Gibraltar Mines Limited (N.P.L.). In this paper, we will also attempt to show the importance of conducting large enough surveys in order to properly evaluate the results obtained from these surveys. LOCATION The orebodies of Gibraltar Mines Limited (N.P.L.) are located on the western slope of Granite Mountain, central British Columbia (52°30' north, 122°16' west) (See Fig. 1). The property lies approximately 28 miles north of Williams Lake, B.C. and can be reached by way of 10 miles of newly improved road from McLeese Lake, on the Cariboo Highway. The area in and around Gibraltar Mines has a moderate topographic relief with elevations between 3,500 and 4,100 feet. {EARLY HISTORY AND GEOLOGY The present Gibraltar Mines property before amalgamation consisted of the Pollyanna property (Duval-Canex) and the Gibraltar property (original Gibraltar Mines) as well as some Coast Silver and McLeese Lake Copper claims (See Fig. 2). The Pollyanna property was first described in the 1917 B.C. Minister of Mines Report which referred to it as the "Rainbow Group". The development at that time consisted of several open-cuts on copper bearing quartz veins.

Jan 1, 1972

By Robert G. Page

"Stabilization" of copper differs from sin in at least one respect - no one seems to be against it. Every time a tycoon in the producing industry pontificates on the economic history of copper, or prophesies its future, he is likely to praise the virtues of "stabilization". Consumers of copper constantly bemoan fluctuations in the supply and price of the metal. Governments in some producing countries, to a greater or lesser degree dependent upon exports of copper for foreign exchange and upon taxation of copper profits for substantial parts of their budgets, are perhaps more eager than any other group for "stabilization".

Jan 1, 1962

By S. R. Stine

The Cyprus Thompson Creek Mine is located at 2,286m (7500 feet) elevation in the Central Idaho mountains, 61.16 kilometers (38 miles) southwest of Challis, Idaho off State Highway 75. The Thompson Creek molybdenum deposit lies near the eastern border of the late Cretaceous Idaho Batholith within a complexly deformed sequence of Paleozoic sedimentary rocks. Molybdenum mineralization is contained in a composite biotite granodiorite-quartz monzonite stock considered to be genetically related to the Idaho Batholith intrusive event. The ore is being mined by open pit methods and delivered to the concentrator stockpile with an overland conveyor belt system. The concentrator is designed as a 22,680 metric tons (25,000 ton) per day plant at an average head grade of 0.1% Molybdenum.

Jan 1, 1986

By Joyce Lappin-Randolph

In 1977, Vertical Crater Retreat (VCR) Mining was developed at the Homestake Mine and by 1983 had become a fully integrated mining method contributing 60% to total underground production. VCR has proven successful for continuous ore blocks exceeding 55,100 tons (50,000 st) with dips greater than 60" and provides a productivity average of 39 tons (35 st) per man shift (tpms) which is 92% greater than Open Cut-and-Fill. Discontinuous ore bodies, small pods, or flat structures not amenable to bulk systems are mined with Mechanized Cut-and-Fill (MCF) and have been able to achieve a 32 tpms (29 st) average productivity. Small, low grade, remnant ore bodies were not economically viable with large scale bulk techniques and couldn't support the development required for a MCF system. As a result, Homestake began researching modified bulk mining methods to increase production rates and maintain safety, while lowering costs. A modified version of VCR with significantly diminished development was prototyped in an effort to reduce initial capital investment and expedite the production phase. This modified method is called Small Block Vertical Crater Retreat (S. B. VCR). Geology The Homestake Gold Mine is located in the northern Black Hills of South Dakota at Lead. Having been active since 1876, it now extends from the surface to the 2,440 m (8000 ft) level underground.

Jan 1, 1987

By K. W. Vincent

This paper, deals with the beneficiation of a low grade Western phosphate to ore. More specifically it summarizes the results of a study made to optimize a scrubbing step in the process, and to provide firmer data for use in plant design. The deposit is situated about 30 miles northeast of Pocatello, Idaho, in the Fort Hall Indian Reservation. It is a bedded deposit and throughout most o the orebody includes three contiguous layers of phosphatic material which differ in P205 content. The J. R. Simplot Company, as operator for a Simplot-FMC joint venture, mines the ore selectively by open pit methods The lower bed containing a nominal 30% P205 is shipped to the Simplot Company fertilizer complex near Pocatello; the middle layer averaging about 24% P205 supplies the FMC elemental phosphorus plant also near Pocatello, The top layer averaging around 16% P205 and designated as mill grade shale is stockpiled for future beneficiation. This paper is concerned with some aspects of the processing of this low grade shale.

Jan 1, 1965

By S. Sener

In this investigation, the changes in the grindability of both ulexite and colemanite related with the different structural modifications created by the heat treatment were examined with respect to work index (Wi). The effects of the heat treatment temperature and time on grindability index were also investigated. It was observed that, heat treatment significantly affected on the grindability of ulexite. The work index of original ulexite was found 7.11 kWh/shton and decreased to 3.5 kWh/shton level within 200-480°C for 60 minutes. On the other hand, the work index of original colemanite was found as 6.48 kWh/shton and no appreciable change was observed when heated up to 320°C. Thermally assisted comminution can be used to improve the grindability characteristics of ulexite. Besides, the different behaviour of ulexite and colemanite under heat treatment can be used for their separation. The artificial mixture of ulexite and colemanite could be separated with over 90% recovery by utilizing their different grindability characteristics by thermal treatment, semi-autogeneous grinding and screening.

Jan 1, 1999

By A. T. Yu

The quest for ore in an open pit is fundamentally an earth moving proposition. This thesis is vividly underscored by the rapidly increasing volume of waste to be removed in newer mines, where in some instances waste to ore ratios have reached as high as 20 to 1. Continuing depletion of high grade reserves, greater demand for raw materials, coupled with ever climbing labor costs, have made the problem still more pronounced and the need for more effective means of earth moving in an open pit even more acute. A conservative approach to the problem has been to upgrade the sizes of conventional earth moving equipment such as shovels and trucks. In many open pits, particularly in the C.S., this has been responsible for the generally down- ward trend of earth moving costs. None the less, the investment costs of these machines are high, and their gigantic engines are seldom fully utilized. Moreover, a large number of operators are required and maintenance remains relatively high. Unfortunately most people have felt that no other viable alternative was in sight within today's technological capabilities.

Jan 1, 1973

By J. E. Shearer

The state of Arizona produced 253,276.2 metric tons (279,000 st) of crude gypsum during 1986. This represents approximately 1.7% of the total U.S. production. Four mines provided Arizona's gypsum, three of these mines are in the San Pedro Valley. The uses of the gypsum produced in Arizona are for manufacture of cement, agricultural uses, and wallboard manufacture. The gypsum is used as a retarder in the manufacture of Portland cement. The use in agriculture is treatment of alkali soils to allow water penetration. Other deposits in the San Pedro Valley have production potential, providing there is sufficient market for additional wallboard. The author completed an evaluation of one property earlier this year.

Jan 1, 1988