Search Documents

By Satya Harpalani

An investigation was carried out to study the microscopic structure of coal in order to understand the phenomenon of methane migration. A Scanning Electron Microscope (SEH) was used to study the surface and pore structure of bituminous coal taken from an underground mine. Micrographs obtained showed the highly porous nature of coal which explains the large quantities of gases that remain within the pores in the compressed and adsorbed forms. These micrographs further showed that most of the pores within the coal matrix are the 'dead-end' type and do not contribute much towards the flow of gas. The most important finding was that solid coal has a network of cracks and fractures indicating that it is these cracks that are primarily responsible for the gas flow, rather than the pores. The size and distribution of the pores within coal influence the capacity of coal to retain methane but movement of the gas molecules is the responsibility of the microfractures. Any mathematical modeling to simulate gas flow through coal must take this into account. For purposes of modeling, the structure of coal can be considered to have dual porosity. First, the gas molecules are released from the pores and there is a gradual migration towards the fractures. Once the gas reaches the fractures, its movement is eased greatly along these fractures.

Jan 1, 1987

By J. L. Parks

Designs, installation procedures, and performance characteristics of martensitic cast steel concaves are reviewed. Longer wear life, fewer pieces to install, and eliminating the need to scarf joints are the principal benefits of using martensitic steel to replace austenitic 12% Mn (Hadfield's) steel, the traditional concave material for large gyratory crushers. Installation procedures that reduce the risk of breakage are described. Operating practices that affect concave performance are also discussed.

Jan 1, 1992

By A. A. Campoli

A stress control design strategy was developed to minimize the explosive failure of highly stressed pillars, during room-and-pillar retreat mining conducted between stiff immediate roof-and-floor strata. A confined core coal pillar strength model was based on in-mine geotechnical evaluations of successful room-and-pillar and longwall bump control designs. Tributary area and linear shear angle approaches were used to estimate development and gob side abutment pillar loads for supercritical section widths. Subcritical width sections separated by barrier pillars to control stress within total extraction panels were optimized with the boundary element program MULSIM/NL.

Jan 1, 1994

By J. F. Snyder

Minor elements determined by atomic absorption spectroscopy include: zinc, cadmium, copper, cobalt, nickel, chromium, manganese, and iron. Of these elements, only three; zinc, cadmium, and copper are found to have been introduced with the ore-forming fluids. Iron, manganese, chromium, and nickel were increased in dolo-stone lithologies when compared to limestone lithologies. The uniform distribution of cobalt suggests this element was neither increased nor decreased during ore emplacement nor during dolomitization of the rocks. Zinc increases adjacent to ore result from leakages into open spaces rather than as pervasive aureoles surrounding ore bodies.

Jan 1, 1977

By W. T. Caneer

Uranium may be in short supply due to the predicted energy needs in the coming years. As a result of this a new surge of uranium exploration is underway. The refinement of numerous exploration techniques has accompanied this surge. One such technique is the monitoring of radon gas in surface soils and rocks as a guide to subsurface uranium deposits. The Colorado School of Mines Research Institute became involved in radon studies in 1967 on a project for the AEC. Since that time the Institute has conducted numerous radon surveys for a large number of companies which have been active in uranium exploration. The objective of this paper is to relate the techniques utilized by the Research Institute and the results of some of the studies performed. Most of the studies performed by the Research Institute were related to roll front, sandstone -type uranium deposits. However, we have performed radon studies in various other types of rock. For those who may not be familiar with the application of radon ?sniffing" in soils and rocks, a brief descriptive background should be given. The following question may be asked -- why use radon as a guide to uranium mineralization? Some of the answers to this question are as follows:

Jan 1, 1974

By Myron W. Mellor

Our efforts at McNally, to find a better way to mechanically separate particles from liquid in a slurry have led to the development of two new centrifuges. The first unit utilizes a slotted opening screen as the filter media and retains all plus 200 Mesh and most of the 200 by 300 Mesh particles. The second unit is a solid bowl centrifuge with a novel method of removing the solids and delivers an effluent containing as little as 300 PPM solids in suspension. The first unit was designed to separate particles in the range of about 1 MM x 0 or smaller top size from the liquid slurry and produce solids having low surface moisture content, and a liquid concentrate containing a low percentage of solids. A prototype of this unit has been in the field undergoing tests for over two years. A few of these test results are shown in Tables I & 11. Testing has been mostly limited to the field of coal, how- ever this does not mean that the machine would accept only coal slurries. The machine has produced a dewatered product having as low as 5.5% surface moisture, and an effluent containing as low as 1.4% solids and handled slurries containing from 15 to 50% solids by weight.

Jan 1, 1975

By Eugene N. Cameron, Igor N. Sviatoslavsky, Harrison H. Schmitt, Gerald L. Kulcinski

The recent discovery of large amounts of helium-3, a valuable thermonuclear fuel, on the surface of the Moon has prompted engineers and scientists to examine the commercial attractiveness, thetechnological feasibility, and the environmental features of this important resource. The main feature of this fuel cycle is the low (˜ 1%) fraction of energy released in neutrons. Such low neutron fluxes result in important reductions in the amount of radioactivity, afterheat, and radiation damage in a fusion power plant. On the other hand, the high fraction of energy in charged particles and synchrotron radiation can be directly converted to electricity, resulting in very high efficiencies of electricity production (˜60.70%). It has been shown that there is 10 times more energy in He3 on the Moon than there ever was in fossil fuels (i.e., coal, oil, and gas) on the Earth. The techniques and equipment needed to extract the helium-3 have been examined and internationally acceptable mechanisms for the industrial development of this resource have been outlined. This paper expands on the financial, environmental, and technical aspects of the recovery of helium-3 for use in the 21st century.

Jan 1, 1990

By Harry G. Hedgepeth

Exploration of the Big Island trona beds by Stauffer Chemical Company started early in 1959. During the intervening time, Stauffer Chemical Company of Wyoming has developed a Large trona mine in this southwestern Wyoming area and has increased the over-all production of soda ash from natural sources by nearly one-half million tons per year. The trona, which is a hydrated sodium bicarbonate mineral, lies some 800 feet into the sedimentary rocks of the Green River formation. Present production is approximately 850,000 tons per year being extracted by means of a room-and-pillar mining system. Conventional coal mining equipment is used with some modification to accommodate local conditions. The mined and crushed ore is hoisted to the surface and processed in an on-site refinery. Refined soda ash is shipped to widely separated locations in covered hopper railraod cars. Construction in progress at Stauffer's plant will double the present capacity.

Jan 1, 1966

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By John G. Holmes

The generation of low cost power is but one phase of the TVA program for regional development. During the 36 years since TVA began, growth in its generation of electric power has necessitated a shift from a predominantly hydroelectric power system to a combination steam and hydroelectric system. The addition of steam-electric power plants to TVA's generating system was necessitated by the rapid increase in the traditional and defense demands for electric power in the 80,000-square-mile area served by TVA, the need to firm up the hydroelectric power, and the fact that all available sites for sizeable hydroelectric projects had been developed. At present TVA owns and operates 40 power plants--29 hydroelectric and 11 steam-electric plants. The total generating capacity of the hydroelectric plants is 3,105,430 kw, and the capacity of the steam plants is 13,951,135 kw. This provides a total generating capacity of 17,056,565 kw for the plants operated by TVA. Individual capacity of the 112 hydroelectric units ranges from 10,000 to 67,500 kw, and the individual capacity of the steam-electric units now in operation ranges from 60,000 to 950,000 kw. In addition to this generating capacity, TVA distributes the power from 6 U. S. Army Corps of Engineers hydroelectric plants on the Cumberland River. These plants contribute an additional 725,000 kw. Also, under an agreement with the Aluminum Company of America, TVA directs the stream flows and generation of their 423,715-kw system on Tennessee River tributaries and shares with Alcoa in the increased generation resulting from this coordinated operation.

Jan 1, 1969

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By R. M. Kakwani

The filtration and dewatering results of -32 mesh Pittsburgh seam coal are discussed with reference to the microscopic structure parameters, i.e., particle segregation in the cake and particle and pore size distributions at different layers. At low solid concentration of 0.33 kg coal/kg water, a non-uniform cake structure is observed in which the particle and pore sizes increase from the top to bottom layers in the filter cake. An increase in the solid concentration in slurry produces more uniform cake structure and higher filtration and dewatering rates. Air bubble entrapment in the coal filter cakes is also discussed.

Jan 1, 1984

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By Jeffrey L. Zelms

There is no known, practical substitute for lead in the automobiles, communications systems, medical equipment and computers that Americans use every day. However, there are many who say lead should be stopped at its source -- banned. As America's largest lead producer, The Doe Run Company has ralized that it must do more than mine and reclaim lead efficiently and safely. It must also earn the public's consent to operate if it is to continue to be a viable business. LEAD - THE BRILLIANT PERFORMER: REFURBISHING AN IMAGE It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. It's been an embarrassingly long time since I was a college student. However, I remember there was no course at the University of Missouri's School of Mines and Metallurgy that had anything to do with the public relations aspects of mining or, put another way, the politicization of mining. I haven’t perused the course catalog for Penn State’s College of Earth and Minerals Sciences. But I strongly suspect I wouldn’t find such a course there today, either. A statement by the chairman of one of the country’s largest chemical companies leads to the point I want to make. He described his business this way. He said, “We’re a public affairs company that just happens to produce and market chemicals.” Like chemicals, minerals and mining are politicized today. To the extent that we don’t understand that reality, we don’t understand that reality – and act on it – we’re less likely to survive in this business. Some of you may well be saying to yourselves, “This guy Zelms is an alarmist.” That’s fair enough. Because it is absolutely true that there’s n o known, practical substitute for lead today. And it’s also absolutely true that, knowingly or not, Americans use lead everyday. It’s in our automobile batteries. It’s an integral part of communications systems. High tech (and low tech) medical equipment contains lead. And lead is an essential component of computer and TV screens. But even with all these uses, lead has a negative image today. An image so negative that its very existence is threatened. If you doubt that, consider these two statements made in 1989. Statement one. “It is probably reasonable to argue that exposure is the single most important and critical environmental health problem in the U.S., and possibly also the world…” Statement number two. “Many of the uses of lead should be terminated. We need to go back to the ultimate source: that is, taking lead out of the ground and putting it into the product stream and we need to turn it off at the ultimate source. Not the approximate lead in gasoline, or lead in air, or lead in food. Go right back to the source and start cranking it down." (End quote.) Those are what I call strong statements. And they weren’t made by some celebrity spokesperson for the environment like Meryl Streep. Both these statements were made by Dr. Ellen Silbergeld, whose long list of professional and academic credentials includes: o Adjunct professor and research scientist at the University of Maryland Medical School and Johns Hopkins: o Chief toxic scientist and director of the Toxic Chemicals Program of the Environmental Defense fund; o and President of the Society for Occupational and Environmental Health. If Dr. Silbergeld were the only person making these kinds of statements, it would be one thing. But she’s not a voice in the wilderness, by any means. Also for those of you who say, well since there’s no known substitute for lead, how on earth could it be banned. I refer you to a number of bills before Congress that would permit the EPA to ban any product if it is determined that its

Jan 1, 1992

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By Bo-Hyun Kim, Mark K. Larson

"Bumps remain a critical safety concern in underground coal mining, despite significant advancements in engineering controls. These events occur when relatively high stresses in a coal pillar in conjunction with low confinement exceed the pillar’s critical capacity, causing the pillar to rupture without warning. Floor failure often occurs and can be an indicator of bump risk, as it is strongly associated with brittle failure known as spalling under a lower confinement. Significant floor heave at a western U.S. coal mine has been observed where the pillar width in a three-entry gate road system was 53 m, while no significant floor heave was observed where the pillar width in another gate road system was 22 m. This phenomenon was widely reported in the region and at another mine in another western coal field it has been reported that larger pillars are always associated with floor heave. In this study, a spalling model based on the S-Shaped brittle failure criterion and associated with the anisotropic characteristics of the materials was used in FLAC3D. The observed floor heave phenomenon associated with the larger pillars was demonstrated using this modeling approach.INTRODUCTIONFloor failure in a coal mines often inhibits longwall mining operation, as large displacement of floor strata, known as floor heave, interferes with travel, access, ventilation, and equipment operation. Aggson (USBM 1978) investigated floor heave in West Virginia where underclay is relatively strong and high horizontal stress is present. It was reported that the failure mode is mainly by buckling rather than by plastic flow.This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock mass behavior in longwall coal mines in highly stressed, bump-prone ground. More specifically, this study attempts to explain through numerical models small energy releases in the form of floor heave. The authors believe that brittle rock failure is associated with both floor heave and some bump mechanisms, if not directly involved in their cause."

Jan 1, 2019

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By James M. Griffin

Ladies and Gentlemen, There have been no less than ten major coal project financings in the last eighteen months. Each of these has been in the order of $100 million to $1 billion for the development of a coal property and its associated infrastructure. It is appropriate at this time to review the nature of these past financings. Why has there been so much activity? There are primarily two reasons. The first is due to the large number of contracts which were signed as a result of OPEC oil shocks. High projections were made for increased coal consumption particularly in world trade. This is distinct from domestic coal mine/power plant projects which often tap a government source of funds. Second is the high cost of coal development in the 1980's compared with a typical company's corporate borrowing capacity.

Jan 1, 1984

By D. H. Lynch

Prompted by the need to conserve energy and reduce operating costs, Agrico Mining Company has made two significant improvements in the transportation of phosphate ore from the mine to the beneficiation plant. One improvement involves a change in a slurry pipeline system which substantially reduced pumping energy, and the other improvement is a major innovation for the phosphate mining industry which involves the transportation of the ore by railroad. This paper briefly describes these two projects.

Jan 1, 1981

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite 'dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976