Search Documents

By B. Petkof

Olivine has been an accepted industrial mineral for the last 50 years. Its initial acceptance was based on the recognition of its refractory properties by European research workers in the middle to late 1920's. Initial U.S. olivine production began in the early 1930's in North Carolina and continues there today. Olivine also is produced in the State of Washington and in other countries.

Jan 1, 1982

By Ch. Apostolaki

Eighty samples from Roman wall paintings from ancient Corinth were studied by means of optical and scanning electron microscopy coupled to an energy dispersive analyzer, X-ray diffraction and image analysis techniques. The goals of the study were the identification of the exact nature of the pigments and the technical features of paint application (binding medium, adherence to plaster, thickness of the pigment layer), which would provide evidence about the painting technique (fresco or secco). The main plaster is calcitic with secondary calcite as a cement binder to the primary calcite grains. All pigments, except Egyptian Blue, were naturally occurring ochres or pigment minerals, such as limonite, goethite, hematite for yellow, brown and red hues, cinnabar for red hues and celadonite for green color. The presence of specific elements such as Ni and Cr or minerals such as olivine, in the yellow, brown and red pigments, gave an indication about the provenance of the original pigments, which seems to be from Cyprus. The black color was represented using charcoal. It seems, finally, that for the pigment application the fresco technique was used, while secco is also apparent.

Jan 1, 2006

By W. Addy Majewski, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) and Diesel Controls Limited evaluated a new diesel emission control system on an underground mine vehicle. The system was a catalyzed ceramic wall-flow diesel particulate filter (CDPF) combined with an catalytic converter, or diesel oxidation catalyst (DOC). This paper describes the design and installation of the system on a load-haul-dump (LHD). The results of screening tests conducted by the USBM are also given. The screening tests were conducted to determine if the device's particulate collection efficiency, regeneration temperature, and effect on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions changed over the period it was being used. The system was removed from the LHD and evaluated in the laboratory after operating for 308 and 1200 hours. After 308 hours of operation, laboratory testing revealed its particulate collection efficiency varied from 41.0 to 93.5 percent, depending on engine operating conditions. Its regeneration temperature was about 415° C. It reduced HC emissions by up to 97.6 percent, and CO by up to 95.0 percent. When tested in the laboratory after operating for 1200 hours on the vehicle, no significant change in performance was observed.

Jan 1, 1995

By Bo R. Arvidson

High-energy product permanent-magnet materials of rare-earth cobalt alloys are being used in applications where space or weight are at a premium cost. New applications like friction-free bearings are also made possible. However, such magnet materials have not been commercially used in magnetic separators until now due to the high cost for the overall magnetic flux generation relative to commonly used ceramic magnets or AlNiCo magnets. The design of the new high-intensity permanent- magnet roll separator (PERMROLL) takes advantage of the unique properties of rare-earth cobalt magnets rather than just substituting for conventional magnet materials now in use for magnetic separators. Hence, the new generation of high-intensity magnetic-roll separators has some unusual characteristics that make known magnetic separation applications more economically attractive, and even expands the magnetic separation technology area to include applications for which no other feasible methods are presently known.

Jan 1, 1983

By E. J. Karges

The use of pulverized coal for generating power and performing industrial processes has made an important contribution to our industrial economy during the past half century. Actually, the burning of coal in powdered form is a subject that has held the attention of engineers for a century or longer. Its widespread use, however, is comparatively recent, As early as 1866 patents were granted to Messrs. Whelpley and Storer for a method of feeding pulverized coal into a furnace as an auxiliary to the grate fuel. In the many tests made during the subsequent years with various kinds of apparatus, the experimenters were handicapped in not getting the coal fine enough to obtain complete combustion and to prevent excessive formation of slag.

Jan 1, 1965

By YU. F. Vasyuchkov, K. Vasioutchkov, B. M. Vorobjev

Introduction It is now believed that, even with the environmental protection measures now being taken, the further application of traditional coal-mining and electric power-generation technologies will inevitably cause further irreversible damage to the global ecosystem. Further improvements in conventional coal-mining technologies, both surface and underground, are expected to have only limited impacts on the economical, ecological and social aspects of coal mining. In countries with a developed coal industry, coal reserves with favorable conditions at shallow depths are rapidly being depleted. Therefore, in the future, more coal will be mined from deeper levels, resulting in higher operational costs and lower labor productivity. The solution to this problem is to be found in developing, promoting and implementing unconventional coal-mining and advanced clean-coal technologies. This paper presents an unconventional concept that has been suggested by the authors. The basic goal is to achieve coal-methane energy resource conservation and to remove barriers to energy efficiency through the adoption of integrated, ecologically clean, innovative technology. The following principles form the foundation of this concept: Energy resource conservation: This principle concerns the exploitation of actual and potential coal-methane reserves in the most effective way with the lowest possible losses and with the application of the most energy-efficient electric power-generation technology. Energy conversion: Energy conversion means the conversion of solid coal to synthetic fuel gas (in situ or in-cycle), the conversion of methane bounded within the coal matrix to free-flowing drained meth¬ane, the conversion of solid coal in situ to a coal/water mixture (slurry), and the conversion of these gas fuels into electric power. Technological and managerial integration: This prin¬ciple means an integration of coal-gas methane min¬ing operations and electric power generation into one commercial mine-to-product enterprise with electric power as the final product. Thus, coalbed methane drainage and coal gasification (both in situ and in-cycle) integrated with a combined cycle of electric power generation constitutes a highly integrated coal-gas methane energy-generation system. The system can be materialized in the form of a local integrated coal-gas electric power complex (LICGEPC). General features of the new concept The coal-gas-methane electricity concept is actually a synthesis of the following four technological components: Coalbed methane drainage. This technique and its utilization attained recognition after commercial operations were proven successful in the San Juan and Black Worriers coalfields in the United States. Worldwide, extensive field experiments and research-and-development activities are being carried out in the area of coalbed methane exploitation and utilization. Recently, coalbed methane drainage for power generation has been undergoing intensive research and development. At the Harworth Colliery in the United Kingdom, a combinedcycle power plant has been built that uses coalbed methane. The plant has an installed capacity of 15 MW Also, Germany, Australia, the CIS and China have conducted various experiments and industrial tests on the use of coalbed methane power generation. Underground coal gasification. Another unconventional technological approach is underground coal gasification (UCG). A number of semi-commercial, demonstration and pilot projects have been undertaken in Russia, the Ukraine, Uzbekistan, the United States, the United Kingdom, Italy and Belgium to demonstrate the technical and economical viability of coal gasification in situ. In Uzbekistan, the Angren coal-gasification station has been in full-scale commercial operation for two decades. The operation supplies a power plant with synthetic coal gas. Under sponsorship of the US Department of Energy's Morgantown Energy Technology Center, large-scale laboratory tests simulating coal gasification in situ were successfully completed by the

Jan 1, 1999

The rheological behavior of high concentrated coal -water slurry (cws), a new liquid fuel, is an important factor in the preparation, transportation and combustion. The conventional viscosimeters designed for Use with true fluids are not suitable to the measurement of the rheological behavior of cws. So that a special viscosimeter of tube type for cws was designed and set up in .laboratory. Experiments using two kinds of cws from two provinces from P. R. Olfna were conducted. It is found from test results that the experimental cws possess the rheological character of Bingham fluid and there is the existence of the wall effects which causes the measurement errors. In our former paper published the wall effects were discussed III the light of methods of Odroyd and Jastrzerbsiki to make the correction of the experimental results. But a number of tests are necessary to meet the need of determining the slip coefficient. In this paper the models of the wall slip velocity and the thickness of the slip layer of Bingham fluid were proposed III in theoretical approach which were satisfactorily used in the correction of the measured results of the rheological character of cws.

Jan 1, 1994

By J. A. Madonna

Universities and colleges in three countries -Australia, Canada and the United States, recognized the need to establish and reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral exploration companies and private consultants cooperated in the study by providing information regarding their specific training needs for support personnel, the data gathered has been used to identify training area for semi-skilled, skilled and technical personnel in geophysics, including, but not limited to, geo-logical skills, geophysical skills, surveying skills, environ-mental skills, and computer skills. With areas of major educational need defined for geophysical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will he discussed.

Jan 1, 1992

By A. Frank Alsobrook

DOUG HALBE: Thanks, Terry. And in spite of your introductory comments, I'm going to attempt to continue our hallowed tradition of saying nice things about the speakers. This is really a serious comment now. We, as mineral processing and mill people, don't often talk to people outside our general operating area. One thing that we've tried to do in this operators' symposium is get speakers from various types of plant operations to help illustrate all the things we have in common. Our next speaker is from the industrial minerals area. I think there's a lot to be learned from industrial minerals operations. Some of the people in the last session learned some things about fine grinding in industrial mineral operations. I was a little surprised to see people there grind to 2 microns. Our next speaker is Frank Alsobrook. Frank is another nonmetallurgical engineer. He has a degree in geology, a master's of science from the University of Wisconsin. He's had his own very successful consulting company for a number of years. This is your 11th anniversary, Frank? Very good. He's also the immediate past chair of the industrial minerals division. I think the folks at the speakers' table should be ashamed. You have been so rowdy that Frank chose to sit in the audience. [laughter] We'd like you to come up now, Frank, and tell us some things that you've seen that might be useful to us. INTRODUCTION FRANK ALSOBROOK: The three topics addressed briefly are (1) teamwork and operations modeling, (2) the pitfalls of capital conservatism, and (3) the potential for by-product recovery. Ideas for improvements in these areas are not unique to industrial minerals but apply to metal mining and processing operations, as well. Several additional topics are suggested at the end of the paper.

Jan 1, 1998

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond's work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By Leon D. Keller

Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units are currently in operation on magnetite, varying in size from 16 ft diameter circular unit to a 25 ft by 100 ft rectangular unit. Additional units up to 38 ft diameter are under construction. Depending upon the application in the flowsheet, upgrading-varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to economically remove as much silica as possible may not be fully appreciated. These figures pertaining only to transportation may be thought-provoking. If a 10,000,000 ton per year plant could reduce the silica content of their concentrate by 17, a savings in boat freight alone would amount to 100,000 tons at $2.00 per ton annually.

Jan 1, 1963

By Turan Uysal, Thierno Saidou Barry, MURAT ERDEMOGLU, Mustafa Birinci

Nonbauxite ores such as aluminum silicate clays and coal fly ashes have been widely considered as potential resources of alumina (Al2O3). The interest focused on these ores is due to their high alumina content. Over the years, in countries where there are little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process is not economical, alternative processes have been explored. Among these processes, acid leaching is seen as the most attractive process. In the acid leaching process, heat treatment for thermal activation to destruct the refractory structure of the minerals in the ores is generally recommended as a pretreatment method. Recently, the applicability of high energy ball mills, which are useful for mechanical activation as a pretreatment method before leaching, has attracted much attention. This is a short summary of our previous review [1], giving the details of alumina manufacturing from thermally and mechanically activated clays and coal fly ashes by acid leaching.

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By Weixiang Meng, Zhao Song, Ming Guo, Zhigao Liu, Shoubao Zhang

"There are many multi-layer coal reserves in China which account for nearly 20 to 25% of the existing proven reserves. When the coals are mined in a descending order using the fully mechanized long wall mining method, they usually have roof collapse with cavity and air leak in roadways and long wall stopes; this is especially relevant when the thickness of the rock between two coals is less than 5.0 m, as the roof stability of lower seam would be greatly reduced. At the Wuhushan Mine, such abnormal strata behavior occurs, including abnormal support stress, irregular period roof pressure, and roof falls in the face. The main reasons for these behaviors include smaller roof thickness, lower rock strength, and mining influence of upper coal; these reasons were determined by analyzing the in situ conditions. A mechanics-based model of the mine geometry was set up to study the sources of stress, the stress evolution of coal, and the discriminant method of roof stability; to obtain the smallest safe thickness of roof between two coal layers, numerical modeling was applied to analyze the relations between the roof thickness and its displacement distribution. Based on the above research, the No.1001 face was divided into easy roof caving zone (ERCZ), roof caving transition zone (RCTZ), and unlikely to roof caving zone (URCZ). In the ERCZ, comprehensive grouting to reinforce the roof was implemented; in the RCTZ, local grouting to reinforce the roof was implemented. Furthermore, a face stability control index and its range were developed in a fully mechanized face combined with mine pressure observation. After implementing this strategy, there have been no unexpected roof caving or other serious strata behaviors.INTRODUCTIONChina is the country with the largest coal production in the world, and the conditions for its coal seams are particularly complicated. For example, in China’s Datong, Wuda, Pingdingshan, and Qinshui mining areas, there are a large number of multi-layer coal seams. The thickness of these coal seams ranges from 1.3 m to more than 10 m, and the spacing between layers is from under 1.0 m to over 30 m. A common problem with these coal seams is that one layer of mining has a large impact on other coal seams, which are customarily referred to as close-distance coal seams. According to statistics, close-distance coal seams account for about 20–25% and 15–18% of China’s coal reserves and production, respectively.From the reference research of Huang (1999, 2002, 2018) and Tu (2010, 2011) we can learn that in the mining process of close-distance coal seams, downward mining is mainly used. When the upper-layer coal is mined, it has a huge mining disturbance effect on the floor (that is, the roof of the lower coal). The mining disturbance increases the mining fissure in the rockmass and weakens the strata strength. The mining problem formed by this issue is that when the lower coal is mined, problems such as difficulty in roadway support, collapse of stope roof, and difficulty in ventilation are often encountered. Especially for the mining of medium-thick coal seam groups with a layer spacing of less than 5.0 m, there has been a large-scale roof collapse accident with a fall height of more than 10.0 m. In response to such problems, domestic and foreign scholars and engineers such as Tan, Zhao, and Xiao (2010), Xie et al. (2017), and others have also carried out targeted theoretical and practical research."

Jan 1, 2019

By Steven M. Bishoff

The reclamation of surface land areas disturbed during the course of coal recovery became a major, universal consideration upon the implementation of the Surface Mining Control and Reclamation Act of 1977. This legislation not only established reclamation as an absolute requirement, but also presented guidelines for reclamation standards and required bond-posting procedures to assure completion of the reclamation process. The Office of Surface Mining was established to enforce the provisions of the Congressional mandate by promulgating specifically detailed regulations and supervising the State participation in this regulatory process. The major operational consequences of the reclamation-related provisions of the Act and the OSM regulations are the increased costs and complex procedures necessary to accommodate the regulatory authorities. It is anticipated that many of these costs and procedures have not been adequately evaluated by either the coal operators or the regulatory bodies. It is, therefore, necessary to proceed with an examination of the general reclamation processes, the effect of these processes on product costs, and the methods, if any, which may be utilized to minimize their impact on the overall operation.

Jan 1, 1981

By J. H. McNamara

A process has been developed for the successful hydrometallurgical extraction of copper from sulfide ores. The extracted copper in the form of a salt is converted by reduction to copper metal. Purification of the metal is described which includes a description of the casting of ETP quality copper wire bars.

Jan 1, 1978

By F. C. Appleyard

A couple of miles southwest of the town of Saltville in the western tip of Virginia is a little village called Plasterco. Gypsum has been produced in this area since about the year 1815, being originally found as small outcrops at the surface. Production in the early days was very small, and the use of the mineral was limited to that of "land plaster" or ground gypsum which was spread on the land to sweeten the soil. In the late 1800's, a small calcining plant was constructed and the production of gypsum plaster began. About this same time, the surface rock was depleted and it became necessary to begin underground mining operations in order to maintain a continuous supply of raw material. The United States Gypsum Company became interested in this property in 1909, and has operated there ever since, having enlarged the calcining mill and built a plant for the manufacture of gypsum wall-board in the middle 1920's. Production of gypsum continues from underground' mining operations, and the present mine at Plasterco is now about 1,000 feet below the surface, making it the deepest gypsum mine' in the world.

Jan 1, 1965

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976

By Yi Zheng

Under normal circumstances, methane released along a longwall face represents only 10%-20% of the total me- thane emitted from the entire longwall panel. However, there might be a sudden surge of methane at the face which may cause a potential problem because the friction from shearer cutting, support movement, and scraper conveyor dragging can be ready ignition sources. Therefore, to predict the distribution of methane will be critical to prevent possible explosions. In this paper, methane dispersion patterns along a lognwall face are simulated under normal and abnormal conditions. With the simulation of methane released from the face, around shearer drum, and from the broken coal on the conveyor, places with possible high methane content can be identified by different phases of working process and shearer positions. Local ventilation measures are evaluated so precautionary measures can be planned ahead.

Jan 1, 2012