Search Documents

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

By Richard Klimpel

1. Introduction Laboratory and industrial grinding tests have shown that the process of size reduction can be significantly influenced by chemicals added to the powder or slurry being ground. The terms grinding aid or grinding additive refers to a substance which when mixed into the mill contents causes an increase in the rate of size reduction. The increased rate can be used to grind a higher feed rate to the desired product size or it can be used to produce a finer product size at a fixed feed rate. Whether the use of a grinding aid is justified in any given situation depends on the cost of the substance versus the improvement of output or product quality obtained with its use. Obviously, an expensive chemical must be effective in very small concentrations if it is to be economically justifiable; the cost criteria is calculated on the basis of the cost of the grinding additive per ton of material ground. Although there is direct experimental verification of the advantageous effect of grinding additives, no sound scientific explanation has yet been offered which explains or predicts the general behavior of additives. Rose and Sullivan have summarized most of the work undertaken prior to 1950 and Hartley, Prisbrey, and Wick have recently prepared an updated synopsis of the grinding additive literature. Many of the studies reported consist of subjecting materials with simple geometric shapes to some type of hardness or controlled single fracture test. On the other hand, a number of the studies were carried out on operating industrial scale mills, with little control or precise monitoring of the effect of the additives.

Jan 1, 1977

By T. W. Lloyd

Accurately predicting coal seam discontinuities is an important part of modern underground coal mining. Conventional methods of coal exploration sometimes fail to identify rapid variations that may seriously impact mining and quality. Radio Imaging Method (RIM), a geophysical approach to mapping longwall panels, has been developed where electromagnetic signals are transmitted and received though the coal block. The amount of signal loss for a given distance, when compared to the coal seam characteristics, identifies anomalous areas. A comparison of RIM predictions with actual geologic conditions encountered during longwall mining demonstrates the accuracy and usefulness of the data.

Jan 1, 1986

By Dennis Z. Mraz

Subsidence profiles over Saskatchewan potash mines exhibit forms which cannot be explained by existing subsidence models. The subsidence is affected by bridging of competent rocks. A modification of the theory can explain the observed displacement of subsidence profiles due to bridging. An unusual shallow secondary subsidence trough has been observed extending two to three kilometers outside the primary subsidence. The secondary subsidence is explained as an elastic compression inresponse to a drop in pore water pressure in the vicinity of the caving zone. The concept of pore water pressure may lead to a safe extraction limit for Saskatchewan mines.

Jan 1, 1986

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona's annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967

By C. L. Sarff

[Automation has become a word that means many things. To management it is the end of the rainbow; you push a button and all your problems are solved. To the working man it is a horrible monster that is taking his livelihood away. To the maintenance man it is a complex that overwhelms him when he thinks of trying to find the trouble when the machine is not operating, properly. Automation has been with us in the coal nines for many years. Long before my time you were using float switches on mine sumps to control the level of the water. That?s automation in the truest sense of the word, but we call it automatic and think nothing of it. If we use the word automatic instead of automation your mine electrician and mechanic will take hold of the problems in stride.]

Jan 1, 1962

By M. M. Fine

Development of a process for winning copper from pelletized chalcocite concentrate without matte smelting and converting is underway at the Twin Cities Metallurgy Research Center, Bureau of Mines. The new route from concentrate to metal includes 2-stage fluid-bed treatment; pelletized concentrate (33 percent Cu, 7 percent S) is first desulfurized (to about 0.5 percent S) in an oxidizing atmosphere, and in the second stage the calcine is metallized by reduction with hydrogen. Thereafter, the reduced product plus 10 percent CaO is routed to a smelting furnace to separate metallic copper from the gangue. Recovery and the Cu content of the product at this point are in the 97-98 percent range. The metal must be refined to remove sulfur and iron to make wirebar copper. An important feature of the process is the pelletizing of the fine concentrate into mini-pellets prior to fluid-bed treatment, which has permitted shorter reaction time, decreased dusting, and facilitated subsequent processing.

Jan 1, 1970

By Gareth Mainwaring

The Cross Harbor Freight Movement Project is currently in the Environmental Impact Statement phase. The scheme is addressing alternative solutions to transport freight across the Upper Bay of New York Harbor, from New Jersey through to Brooklyn, Queens and Long Island. Amongst the alternatives being assessed are two tunnel options; from the north shore of Staten Island through to Brooklyn, and from Jersey City to Brooklyn. These tunnels are approximately 30,000 feet in length, and with up to17,000 feet under the Harbor, would make it one of the longest undersea crossings in the world.. The paper addresses the development of the project, from the Major Investment Study through to the current EIS, and describes the tunnel schemes that are being taken forward. The geological conditions that will be encountered, proposed construction methods, and the ventilation issues associated with such major undersea tunnels will all be described.

Jan 1, 2003

By Fathi Habashi

SOLVENT EXTRACI ION involves two operations: 1) Extraction The metal values in the aqueous phase are extracted by agitation with an organic solvent immiscible in that phase. The two phases are then allowed to separate; the aqueous phase is discarded or recycled and the loaded organic phase saved.

Jan 1, 1970

By S. Frimpong

The coal mining industry is an important sector of Canada?s economy. The cost of mining and haulage of coal in Western Canada is a major focal point when compared to inexpensive coal from Australia. Spot coal price volatility affect contractual price arrangements and this creates pressure on companies? profit margins and their competitive edge. In order to alleviate this pressure, companies may have to take short-term drastic measures that may hurt their strategic positions in the long-term. Companies must also create a mix of their products to ensure effective maintenance of profit margins given various quantity and quality constraints. In this paper the authors provide extensive analysis based on detailed probabilistic production systems for coal extraction and haulage in Western Canada. An optimization model is formulated for typical coal mining operations, processing and haulage from mine sites to the Vancouver Ports using linear programming algorithm. A stochastic model is also formulated to analyze the associated risks and uncertainties. These models are validated using data from five operating mines in Western Canada with varying quantity and quality products and uncertainties. The results show that the five mines studied have to produce between 180,000 and 2.10 million tonnes of metallurgical coal and between 70,000 and 2.16 million tonnes of thermal coal to enhance their profitability given the underlying constraints. The average expected probability of success associated with production capacities from these mines is about 66%. This results in a failure probability of 36%, which is extremely high under contractual arrangements. The results also show that management?s profit expectation of $83 million can be achieved at a zero percent failure probability. With a higher risk of failure of 10%, this expectation increases by 21% to $100.3 million.

Jan 1, 2011

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well approved Tunnel Seismic Prediction System (TSP) has been substantially enhanced for online geological prognosis in underground construction. The method provides high resolution seismic images of the rock mass ahead of a tunnel face via an array of standard anchor rods. These contain3D-geophones and can routinely be installed during the excavation process. A further outstanding feature of the system is the newly developed high frequency repetitive seismic source which can easily be fixed at a tunnel boring machine. A user-friendly software package enables online data acquisition, processing, 3D-visualization, and interpretation.

Jan 1, 2001

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By Gregory R. Wessel

Sulfur is a nonmetallic element widely distributed in nature and of great physical and economic importance. It is the 14th most abundant element in the Earth's crust (0.06%) and an important constituent of animal and plant life. Sulfur has been known and used since ancient times for a number of medicinal and industrial uses. At present, most sulfur is used to generate sulfuric acid that is used in a wide variety of industrial processes, particularly the production of fertilizer. Because of this, sulfuric acid (and hence sulfur) consumption is often regarded as a good index of a nation's industrial development. In the past, sulfur was mined from surface occurrences in several geologic environments, and was used in relatively small amounts. With time, the uses of sulfur and sulfuric acid expanded, as has the need for larger quantities of these commodities. Sulfur is now mined from both surface and underground deposits, and is recovered as a byproduct from a number of industrial processes. Despite valiant efforts and years of work by sulfur explorationists and others, many aspects of sulfur mineralization remain controversial. Almost as controversial is the spelling of the word sulfur. The English spelling sulphur commonly is used outside America and in the American sulfur mining industry, but sulfur is the correct American spelling as approved by the American Chemical Society, the American Geological Institute, and many others. Those new to the American sulfur industry often find it puzzling to be reprimanded for using the correct American spelling. Sulfur resources are abundant and widespread, but the extent to which they can be classified as reserves is constrained by pre- vailing prices and extraction technologies. At present, sulfur can be economically mined from very few deposits. The sulfur industry is roughly divisible into two sectors: voluntary (or discretionary) and involuntary (or nondiscretionary). In voluntary production, the mining of sulfur or pyrites is the sole objective, and the recovery of the resource is as complete as economic conditions will allow. During involuntary production, sulfur or sulfuric acid (termed recovered sulfur) are produced as byproducts, and the quantity of the output is dictated by the demand for the primary product. Voluntary sulfur now accounts for only about 35% of the elemental sulfur produced worldwide, and most inves- tigators believe that voluntary sulfur will be less important in the future. Sulfur sources and products are described as follows (after Barker, 1983): Sulfur Sources: Combined sulfur-sulfur that occurs in nature combined with other elements, commonly referring to sulfides and sulfates. Cupriferous pyrites-pyrite containing minor amounts of cop- per sulfides. Hydrogen sulfide-a toxic gas that occurs in petroleum and natural gas. Involuntary sulfur-sulfur produced as a byproduct in response to legislative or process mandates. Native sulfur-naturally occurring elemental sulfur. Nonferrous metal sulfides-opper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfur complex organic sulfur compounds that occur in petroleum, coal, oil shale, and tar sands. Pyrites-iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfur-sulfur contained in anhydrite and gypsum. Voluntary sulfur-sulfur produced in response to market demand. Basic Sulfur Products: Acid sludge-contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-synonymous with crude sulfur. Bright sulfur-crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-solid crude sulfur crushed to -8 in. Byproduct sulfuric acid-sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-commercial nomenclature for elemental sulfur. Dark sulfur-crude sulfur discolored by minor quantities of hydrocarbons, ranging up to 0.3% carbon content. Elemental sulfur-processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-elemental sulfur produced from native sulfur sources by the Frasch mining process. Liquid sulfur-synonymous with molten sulfur. Liquid sulfur dioxide-purified sulfur dioxide compressed to the liquid phase. Molten sulfur-crude sulfur in the molten state. Prilled sulfur-solid crude sulfur in the form of pellets produced by cooling molten sulfur in air or water. Recovered sulfur-elemental sulfur produced from combined sulfur sources (including byproduct hydrogen sulfide, but sometimes referring only to sulfur from fossil fuels) by any method. Slated sulfur-solid crude sulfur in the form of slate-like lumps, produced by allowing molten sulfur to solidify on a moving belt. Specialty sulfur-prepared or refined grades of elemental sulfur that include amorphous, colloidal, flowers, precipitated, wettable, flour, and paste sulfur. Sulfur ore-unprocessed ore containing native sulfur.

Jan 1, 1994

By A. C. Alexander

Chevron Resources Company owns and operates an open pit phosphate mine and mill 11 miles north of Vernal, Utah. The plant currently produces 500,000 tons per year of concentrate and has the capacity to produce 750,000 tons per year. The operation is currently being expanded to 1,300,000 tons per year of concen¬trate in order to supply a new fertilizer plant being constructed by Chevron Chemical Company in Rock Springs, Wyoming. A 10-inch, 96-mile pipeline is being built to transport the concentrate from Vernal to Rock Springs. The present and expanded operation will be discussed. HISTORY In 1915, Harry Ratliffe staked nearly 15,000 acres of low to medium grade phosphate rock along the southern flank of the Uintah Mountains. This deposit became the largest privately owned phosphate deposit containing approximately 700 million tons of reserves. Initial development of the deposit began in 1958 by San Francisco Chemical, a joint venture between Stauffer Chemical Company and Mountain Copper Limited. In 1968, Stauffer Chemical Company bought out Mountain Copper Limited and became sole owner and operator. In 1981, Chevron Resources Company bought the property from Stauffer and has operated the mining and milling operations since.

Jan 1, 1985

By S. Bastola

Over 80% of roof falls in Illinois coal mines occur at intersections. Regular intersection geometries with sharp corners have been typically analyzed in literature. This study has analyzed stress distribution around typical field 4-way intersection geometry and compared it with similar data for regular four-way intersection geometry. These analyses were performed using 3-D numerical analyses for a typical lithology associated with No 6 coal seam in southern Illinois. Linear elastic and non-linear analyses, using Hoek-Brown failure criteria for different lithological units, were performed. The 3-D models incorporated bedding planes and pre-mining horizontal stresses. Effect of diagonal widths of the intersection and pre-mining horizontal stresses were examined due to their influence on stability. In addition to stress distribution, contours of safety factors, and displacement analyses were performed to assess stability of intersections.

Feb 27, 2013

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

By M. Popescu

In the southern part ?f the Occidental Carpathians an iron ore body embedded in crystalline schist was exploited. The presence of minerals such as magnetite, pyrite, pyro-chorine, allanite, monazite and xenotime, which also include within their structure substituted thorium isomorphic, was pointed out. The iron ore was processed by crushing, grinding and magnetic separation in order to obtain magnetite concentrates. The environment was affected by pollution generated by the mining activities. In 1995 due to the economic reasons, it was decided to cease mining exploitation and remediate the area. The paper presents the ecological impact caused by mining activities on a number of environmental targets and the population. The pollution sources, namely sterile dumps and mine waters are characterized (from the physical, chemical and radiometric point of view); the pollution pathways and theirs effects on potential targets, namely soil, vegetation, hydrographic network and population are identified as well. The degree of pollution due to all sources was assessed and maps of pollution sources distribution were generated. The supplementary effective doses for the population were assessed using rigorous scenarios and considering all exposure pathways. The rehabilitation plan includes solutions for dumps geometrization, covering and revegetation as well as mine waters management.

Jan 1, 2005

By John W. Antalovich

Normally I would like to begin a talk on photogrammetry by defining the word. However modern technology has changed the science so radically that it bears little resemblance to its original definition. Photogrammetry as defined is a science of taking accurate measurements from photography. Today's photogrammetrist, in addition to working with photography, finds himself working with magnetometers, infrared scanners, radiometers, holo¬graphy, lasers, side-looking radar, digital interfaces, computers and countless other modern space age concepts. The modern photogrammetrist is a pilot, photographer, lab technician, mathematician, geologist, programmer, engineer, physicist, and cartographer. His modern instrumentation and many spheres of activity all have a role in the environmental sciences. For example, the magne¬tometer which measures the earth's magnetic fields is used to locate the earth's ore deposits. The infrared scanner captures the heat emitted from the earth to detect ground waters and thermal pollutions. To elaborate on each of his many endeavors would take volumes rather than this short paper. I have elected therefore to discuss what I feel is his most important role in the environmental sciences - that of cartographer.

Jan 1, 1970

By Henry N. McCarl

[ ]

Jan 1, 1966