Search Documents

By D. Corrigan, A. Ahmad, R. Sood, J. Bratt, R. Holt

Zinc oxide based electronic ceramics are being used increasingly to protect electric and electronic circuits against transient voltage surges. Varistors are produced by sintering and annealing ZnO based powder compacts through long sintering and annealing cycles. Because of the length of these cycles, a manufacturing plant is saddled with expensive high temperature equipment with low throughput. Ceramics Kingston Inc. has developed a new technology that uses 2.45 GHz microwave energy for sintering and annealing. The new technology has the potential for increasing equipment and labour productivity very considerably. Additionally, the new technology will result in appreciable energy savings and add flexibility to the manufacturing process. Microstructural examination of varistors sintered conventionally and by microwave technology showed considerably smaller grain size in the microwave sintered materials. The electrical properties of the microwave sintered ceramics compare very favorably with those of the ones sintered conventionally.

Jan 1, 1990

By Eric C. Schwamberge, Clem A. Pelletier, Deborah L. Muggli, George W. Poling

The Pit Lake at Island Copper has evolved into a 3-layered meromictic system. Acid Rock Drainage (ARD) is collected and injected into the lake at 220 m depth via 2 diffuser systems. In situ dye studies were conducted during 2 differing hydrological regimes in order to determine the behavior of the ARD plume within the Pit Lake. Results indicated that when runoff from the waste dumps was low, the injected ARD remained within the bottom half of the intermediate layer of the Pit Lake, initially below depths of 90 m. However, when runoff from the waste dumps was high, the injected ARD at -220 m depth rose through the intermediate water column layer rapidly, but did not breach the top pycnocline at -10 m depth. Overall, the system is currently performing as a mixing bowl with a strong boundary or cap at the upper pycnocline. maintaining mixing below the 10 m depth water level.

Jan 1, 2000

By William F. Butler

I propose to do three things today. First, take a broad look at the role of mining in the Latin American economy; then, review briefly the current situation in four principal metallic mineral exporting nations -- Chile, Mexico, Peru and Venezuela; and. finally, raise some, policy questions that seem to me to be important. The Role Of Latin America In World Mining First, let's consider Latin America's position in world mining markets. Latin America provides more than 5% of world output in 16 metals or ores, ranging from antimony and barite to Tungsten and Zinc. Latin America supplies a fifth or more of the world's antimony, beryl, bismuth, copper, fluorspar, silver and Tellurium.

Jan 1, 1962

By Paul Clifford

The Florida Institute of Phosphate Research (FIPR) is an independent, state of Florida research agency. It was created in 1978 to conduct research to enhance the competitiveness of the Florida phosphate industry. The institute also conducts research to prevent, minimize or rectify environmental impacts caused by the industry. And it helps educate the public concerning phosphate-related technology and issues. FIPR is funded by a severance tax on the industry and is governed by a five-member board of directors appointed by the governor. FIPR's research is playing a role in enhancing the competitiveness of the Florida phosphate industry. Its technology research program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. It is developing new and improved methods of beneficiation and fertilizer production. This includes new process flowsheets and on-line analyzers and process control methods. FIPR is also developing uses for the phosphogypsum byproduct of phosphoric acid production and evaluating the risks associated with its uses.

Jan 1, 1998

By J. Pinkley

In June of 2002 Hilti North America received the first MSHA permissible approval for usage of a powder actuated tool device in a gassy mine atmosphere. The purpose of this paper is to discuss the implementation of this commonly utilized tool technology in the construction industry, to the underground gassy mining industry over the course of the last 5 years. Prior to June of 2002, underground gassy mining industry had attached materials such as ventilation curtains, power cables, communication cables, signage, and other materials by either manually driving individual spads or nails into the mine roof or rib or by attachment to existing roof bolt bearing plates. The Hilti DX 460 powder actuated tool is portable, durable, and lightweight (4.5 pounds). The Hilti DX 460 powder actuated tool system is powered by Hilti .27 caliber permissible explosive boosters. The energy force of the Hilti .27 booster?s acts on a captive piston principle in the Hilti DX 460 powder actuated tool, that applies the setting force for the direct fastening to the individual fastener chosen for the application by the end user. Each year Hilti can be called upon by MSHA to provide booster materials for re-testing per our Hilti DX PAD 1/00 approval.

Jan 1, 2008

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By Kal V. S. Sastry

Conventional iron ore balling circuits exhibit undesirable surging behavior which is known to result from uncontrolled occurrence of the mechanisms of nucleation, coalescence and layering. This study was undertaken to investigate the mechanism of pellet growth by layering. Several laboratory experiments have been carried out to delineate the effect of feed moisture content and feed quantity. This paper presents an analysis of the experimental results and a simple model to describe the layering process.

Jan 1, 1993

By G. J. J. Aleva, A. H. Hilversum

The northern spur of the Bakhuis Mountains contains bauxite deposits on a dissected planation level, a region formerly indicated as the Adampada-Kabalebo area. Iron-rich laterites are ubiquitous on all more or less flat and horizontal to moderately sloping interfluves and planation levels. The known aluminous laterites and bauxites are restricted to those laterites that have relatively leucocratic and silica-poor parent rocks. The whole area is underlain by high-metamorphic Precambrian. In the northern half of the Guiana Shield at least four Cainozoic planation levels can be distinguished. The bauxite and aluminous laterite deposits are related to the oldest, Early Tertiary level. These deposits, occupying the highest positions in the present day landscape, show the destructive influence of post-laterite weathering, erosion and denud- ation; they are erosion remnants and as such are of irregular thickness, grade and shape. Consequently, exact mineable tonnages can only be determined after intensive and detailed sampling and evaluation, taking into account the latest technical and economic parameters. The bauxite potential of the region is negatively influ- enced by the complicated uplift history of the Bakhuis horst, and positively by the presence of suitable parent rock and possibly more than one phase of bauxitization.

Jan 1, 1984

By I. K. Kapageridis

Environmental management and planning requires the integration of large volumes of disparate information from many sources and the analysis of this information with efficient tools for assessment and evaluation. Effective methods of communication that allow interactive participation in the planning, assessment and decision-making processes are also very important. The VULCAN software package from Maptek (Pty) Ltd comprises a large number of 3D graphical tools within an interactive 3D interface called ENVISAGE. These tools are designed and developed to help engineers and scientists to identify and solve environmental problems. The combination of VULCAN 3D Software and the I-SiTE 3D Laser Imaging system leads to powerful solutions for environmental management. This paper presents the capabilities of this integrated system and its applications for environmental management.

Jan 1, 2002

By John E. Roberts

People are not a novelty. But the phenomenal numbers thereof, who have approached, settled, and been born in California in the past twenty-five years, are such a problem as to be a novelty in the broadest sense of the word. California, with less than 7,000,000 people in 1940, and over 19,000,000 in 1966. In 5 1/2 years, (1960-65) the southerly 14 counties of California, which together comprise one-half the land area of our state, had an increase in population greater than Colorado, or Arkansas, or Oregon, or any one of 19 other states.

Jan 1, 1967

By R. B. Krog

Airflow patterns in longwall bleeder systems are affected by gob permeability and porosity and the condition of the gateroad entries after mining. As longwall panels are mined, areas of the caved zone and portions of the remaining gateroad entries become inaccessible, making direct ventilation measurement impossible. Mine operators are left to estimate direction and amount of airflow in the gob and the surrounding gateroads. The most readily available locations are where air enters the worked-out area, approved measurement point locations (MPLs) and/or evaluation points such as bleeder evaluation points, intake evaluation points, and the outer bleeder entry. Ventilation models (network or Computational Fluid Dynamics, CFD) can model the gob and the surrounding bleeder system but calibrating these models is difficult without field data. NIOSH installed a tube sampling system ahead of a longwall face and, as the face retreated, released a slug of tracer gas (SF6) to determine transportation times and flow rates in the inaccessible gateroads. The data was used to calibrate both network and CFD ventilation models for a longwall panel. Both model types were used to predict the airflow patterns in the gob and to determine the airflow rate from the longwall tailgate corner back to the bleeders.

Jan 1, 2011

By M. J. Virnig, Christopher A. Fleming

THE CIP PROCESS "IN THE RIGHT PLACE AT THE RIGHT TIME? After its tentative introduction to the precious metals mining industry in the earlier part of this century, the carbon in pulp (CIP) process has now come of age, and is the process of choice on all new gold mills. Well over 50 percent of all gold that is mined each year is recovered by adsorption on activated carbon, and the percentage will increase in the years ahead, when old mills using Merrill Crowe technology come to the end of their lives, and as the proportion of world gold production from low-grade resources increases. The pioneering process development work in this field, which was mainly concerned with carbon elution, was carried out by Zadra and his colleagues at the United States Bureau of Mines in the early 1950's (Zadra et al., 1950, 1952), and led to the commissioning of the first large-scale, industrial CIP plant, at the Homestake Mine in South Dakota, in 1973 (Hall et al., 1974). From there, the process spread rapidly, firstly in South Africa in the late 1970's. and then throughout the rest of the gold producing world in the 1980's. There were several factors that led to the meteoric (by gold industry standards) acceptance and successful implementation of this new technology into gold processing operations worldwide. Firstly, and perhaps most fortuitously, the development of the technology closely paralleled the 1968 release of the gold price from the rigid constraints of the $35/oz. gold standard. With the value of the metal allowed, for the first time in modern history, to fluctuate in response to free market supply and demand forces, the gold industry witnessed an unprecedented boom as the price of their commodity increased ten-fold in a remarkably short period of time. This had several important spin-offs as far as new process developments were concerned: The profits realized by established gold-mining companies increased enormously and, consequently, there was more to spend on research and development and exploration for new deposits.

Jan 1, 1993

By D. H. Carlson, J. H. Johnson, C. F. Renders

Research was conducted at a western coal mine on a wide variety of underground mining vehicles to develop testing procedures for portable instrumentation monitoring of tailpipe concentrations of diesel particulate matter (DPM), carbon dioxide (CO2) carbon monoxide (CO) and nitric oxide (NO). DPM was measured using the Emissions Measurement Appa¬ratus (EMA) developed by Michigan Technological University (MTU), and an ECOM-KL five-gas analyzer was used to measure gaseous tailpipe concentrations. Baseline concentrations of the tailpipe pollutants were measured using vehicle systems to load the engine. Concentrations before and after the water scrubber were measured and water scrubber efficiencies were estimated by calculation. Field measurement procedures were established. Heavy-duty vehicles with automatic transmissions were loaded using the torque converter to stall the engine. Consistent engine loading for light-duty vehicles with manual transmissions involved placing the transmission in neutral and adjusting the throttle to maintain a constant engine speed of 2,500 rpm. Tailpipe CO2 concentrations for Caterpillar 3306 and 3304 engines were compared to laboratory CO2 data from Caterpillar and MSHA to help determine if engine settings were correctly adjusted for operation at high altitudes. (Perfect agreement between the mine vehicle tailpipe and laboratory measurements would not be expected because of the differences in the test conditions.) DPM concentrations for light-duty vehicles ranged from about 20 to 160 mg/m3, and one light-duty vehicle averaged near 1,000 mg/m3. DPM concentrations for heavy-duty vehicles ranged from about 55 to 200 mg/m3. Widely ranging DPM concentrations for a particular vehicle type reflect the state of maintenance, fuel rate settings and different engine loading procedures as well as differences between samples collected upstream and downstream of the waterscrubber. The calculated DPM removal efficiencies due to the water scrubber varied considerably between vehicles, ranging from 13% to 51%. Calculations indicate that, under worst-case conditions, very large reductions in DPM may be required to meet the proposed DPM PEL of 0.15 mg/m3, even on vehicles with water scrubbers. In-mine ambient air studies, which are needed to actually measure the impact of the tailpipe concentrations on the work environment and the effect of mine ventilation on the dilution of DPM were not done in this first set of tests.

Jan 1, 2000

By Nelson R. Shaffer

Glamorous, burgeoning biotechnology and mundane industrial minerals would at first glance seem to share little in common, but in truth, modern biotechnology depends on many minerals. Biotechnical processes also can be used in industrial mineral extraction and processing. Biotechnology is broadly defined as the application of biological organisms, systems, or processes to manufacturing and service industries. Genetic engineering has reinvigorated one of mankind's oldest sciences, biotechnology, into a booming business. Many modern processes depend on microorganisms cultivated under very stringent conditions in bioreactors. Minerals from carbonate, sulfate, chloride, nitrate, phosphate, and silicate families are used to provide essential nutrients and to regulate growth conditions (such as pH) in order to assure optimal growth of organisms. Certain cells or enzymes perform better when immobilized upon or within solids, and minerals are often used to immobilize cells, especially in continuous process. Minerals are also used extensively in separating and purifying products of biotechnology. Diatomite, zeolites, and silica are especially useful in purification processes. Industrial minerals also are commonly used to clean up large volumes of process water that must be treated. Biotechnology can be employed in exploration, extraction, and processing of geologic materials and in reducing mining or other environmental problems through bioremediation. Microbes have been shown to solubilize certain elements and so promote extraction of heavy metals, phosphate, aluminum, potassium, and even rare earth elements. In a related technique, unwanted materials such as pyrite impurities can be leached microbially to produce cleaner products in sand and clay industries. Microbial actions can modify surface characteristics and so enhance certain ceramic properties. Certain organisms can accumulate useful elements from dilute sources; others can transform unusable chemical species to more useful forms. Deterioration of stone, concrete, and even glass or brick, can be accelerated by microorganisms. Control of such biodeterioration could improve long-term performance of industrial mineral products. Microbial processes have shown promise in improving several mine-related problems. Certain bacteria help remove clays from phosphate slimes and other suspensions. Others are used to degrade cyanide or other organic chemicals such as floatation aids. Cells immobilized on clays have been especially efficacious in bioremediation. Biotechnology industries, like the industrial minerals industries, encompass huge ranges of materials and processes. Costs of products from these industries range from pennies to thousands of dollars per unit, and their products are vital for maintaining modern life styles. Many biotechnical processes depend upon industrial minerals and certain biological processes can be harnessed to do useful tasks in the minerals field. The interplay of industrial minerals and biotechnology is important today, and as biotechnology advances, its interaction with the industrial minerals industry can only increase.

Jan 1, 1995

By Juan H. Rojas

The Chuquicamata mining and metallurgical complex is the main division of CODELCO-CHILE. Its comparative advantage in the world of primary copper producers had deteriorated severely and, consequently, its top management launched an extensive modernization plan. This paper shows how Chuquicamata recovered its position as a low-cost copper producer and is now well positioned to face the end of this century, as far as competitiveness is concerned. It also shows the company's vision for the )(XI century. Given the volume of its ore reserves, one possibility is expanding the sulfide production line capacity, while in the case of the oxide production line, ore reserves are limited so that there is a need to maximize the effectiveness of both organization and technology use. A final consideration has to do with the balance of supply and demand. Most observers of the copper market agree that supply is growing faster than demand. On the other hand, copper is facing severe environmental problems, especially in the piping business, plus the usual threat of substitution. Nevertheless, copper producers are making very weak efforts to defend the market and increase copper consumption through the promotion of new uses of the metal. This issue is crucial and must be considered if copper producers want to maintain a profitable market.

Jan 1, 1998

By C. W. Overton

The operations of Bethlehem Copper are situated in the south-central interior of British Colombia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Colombia. The minerals are chiefly chalcopyrite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies sane pyrite is present. Average grade of mill feed is 0.55% copper.

Jan 1, 1973

By Robert Marks, Enrico Dal Negro, Richard Schulkins

"In July 2012 construction started on the Grosvenor project, a five million tonne per annum underground longwall mine planned for Moranbah in Central Queensland. Grosvenor is located immediately to the south of the existing Moranbah North mine which has been in operation since 1998. EPBM technology is being used for the first time in Australia for excavation of a coal drift. The TBM was used to build two drifts on the project, one for the coal conveyor which will transport to surface, and another for people and equipment to access the underground once the mine’s operational (as shown in figure 1). The TBM will pass beneath a steel archway roof that has been installed at the drift’s entrance and begin drilling into the ground to build the seven metre diameter tunnel, descending at an angle of one in eight until it reaches the depth of the coal seam approximately 160 metres below.INTRODUCTION AND BACKGROUND The first TBM used in a coal mine was in 1962, a Wohlmyer, in Westerholt, Germany. A further 75 km of tunnels were excavated in coalmines within Germany between 1971 to 1983. This paper will review the Grosvenor Mine project (Grosvenor) owned by Anglo American Metallurgical Coal (Met Coal) includes the construction of a new underground coal mine and surface facilities on the northern boundary of the town of Moranbah in the Central Queensland Bowen Basin coal precinct. The contract to undertake the underground development works was awarded to Redpath in 2012. The scope of the Grosvenor Project was to construct temporary office and workshop facilities, install 2 portal arches, backfill boxcuts and infrastructure, excavate by EPBM method 967 m of 1:6 gradient Conveyor Drift and 1,258 m of 1:8 gradient Transport Drift, development of 2,520 m of pit bottom area roadways and development of 10,550 m of the first longwall tailgate. In the following figures 2 and 3, is possible to see the aerial view of the job-site."

Jan 1, 2016

By Patrick Oriez, Chris Norris, Alain Mercusot

"Temporary mechanical ventilation is one of the fundamental requirements in guaranteeing a healthy atmosphere in underground construction works in order to protect the health of persons working on the site. It is therefore essential to conceive a system which meets the requirements of the whole of the worksite and for all phases of work which takes into account all aspects pertaining to its design, dimensioning, justification, installation, maintenance and validation. In doing so, the ventilation design and the selected apparatus to be installed shall meet with the degree of health protection and the quality of air of the worksite as defined by the legislation in force in France, through limiting the concentration of the different pollutants associated with the site activities. Consequently, when presenting a mechanical ventilation project, all of the participating parties and especially the contractor make a commitment to guarantee sufficient volumes (or airflow rates) of fresh (non-polluted and oxygenated) air and extracted (polluted) air in order to meet these limitations and maintain them in all conceivable site configurations. This article sets out the most important aspects of the implementation of a ventilation project from the initial design stage through to its application, discussing French legislation, ventilation principles, calculations and techniques with regards to underground construction sites. BASICS OF VENTILATION Mechanical ventilation studies are concerned with all of the site workstations and work phases which are sources of pollution and apply to all zones of the underground worksite with the goal of maintaining the concentration or composition of this pollution below the permitted levels and comply with the following three basic principles which are complementary to one another without being in contradiction. •,The first principle consists in eliminating or limiting as much as possible the emission of any polluting, irritant, or dangerous substances, by specifying appropriate construction techniques and equipment (use of electric motors, combustion engine equipment: filters, tanks, catalyzers, use of less polluting explosives, damping down dust with water or wetting products, damping down and diluting certain gases using water mists). •,The second principle is designed to capture residual polluting substances emitted close to the source in order to prevent them from spreading into the worksite atmosphere (extraction ventilation with ducting up to the source – upstream of the extractor fan – and use of downstream filters before expelling the polluted air to the exterior). •,The third principle involves accompanying the capture of the pollutants with additional blowing ventilation specific treatment of substances dissipated by and distant from the source of pollution (acceleration of the drift air flow in order to confine dust and better capture it, supply ventilation with ducting in order to dilute the gases emitted and discharge them to the exterior)."

Jan 1, 2016

By R. H. Lambeth

Disposal of mine tailings in "waters of the United States" is presently prohibited even though case studies indicate that the practice may be environmentally viable. To simulate disposal in the natural environment, nine containers of tailings and sediment were instrumented and placed on the ocean floor near Juneau, AK as were ninety-six biosample containers. Pore water concentrations of five metals were determined, and biota populations were characterized for both materials. After 500 days of exposure there were no statistical macro scale differences between tailings and sediment biota populations or Cu, Pb, and Zn pore water concentrations. Tailings released slightly more Fe than sediment, but sediment released significantly more Mn than tailings. Disposal of mine tailings in marine waters may be environmentally safe.

Jan 1, 1998