Search Documents

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By C. Sun

Due to unfavorable geological condition, excessive deformation of mine drifts occurred in a large underground copper and nickel mine. In searching for a solution, a comprehensive underground monitoring program was implemented and the opening convergence and the surrounding rock deformation were monitored. A large number of field data were collected and thoroughly analyzed. The convergence and deformation as function of time and depth were determined and a rock stability index was proposed. Based on the deformation-time and deformation-depth relations, critical deformation times and locations were identified and defined as characteristic values to be used for mine opening and support designs. The characteristic values are critical in the application of two-step supporting system, and the determination of support parameters. The application of the method developed in this study has demonstrated that this practical approach in support design and installation is effective. With the two-step supporting system, a long-term drift stability can be achieved in the mine.

Jan 1, 1998

By T. P. Lim, J. A. Cherry, A. J. Vivyurka, R. D. Blair

The first phase of an investigation of the chemical composition of subsurface water and the hydrochemical processes in and near the abandoned Nordic tailings at Elliot Lake, Ontario, was conducted in 1979. The Nordic area, which covers 85 hectares with an average thickness of 10 m and overlies deposits of permeable glaciofluvial sand, contains 15 million tonnes of tailings with 4-7% pyrite. Nests of standpipe piezometers installed at three locations on the tailings indicate that seepage through the tailings is predominantly downward. The water table in the tailings slopes from the north side of the tailings dam, where it is within a metre of surface to the south side near the tailings dam, where it is approximately 10 m below surface. When they were deposited during the period from 1957 to 1968, the tailings contained pore water at a pH of about 8 resulting from neutralization treatment in the mill. At the three piezometer nests, the pH increases from 3 near the water table to 7 near the bottom of the tailings. The pore water in the tailings is gradually becoming acidic because of oxidation of pyrite in the zone above the water table. The concentrations of Fe, Mn, Ni, Co, Zn and Pb are high in the shallow acidic zone and much lower in the deeper neutral zone. Concentrations of 226Ra range from 30 to 230 pCi/L. At the three sites concentrations of major ions in the permeable sand a short interval beneath the tailings indicate 226Ra presence of tailings seepage, but Ra concentrations are only 2 to 8 pCi/L. Greater downward penetration of 226Ra probably occurs in the area closer to the tailings dam. Monitoring of a network of multilevel bundle piezometers installed in permeable sand that extends southward from beneath the tailings indicates the occurrence of a plume of tailingsderived water containing high concentrations of Ca, Mg, Fe and S04 that extend 400 m downgradient from the tailings dam. The total dissolved solids decline from 20,000 at the dam to less than 500 mg/L at the identifiable downgradient periphery of the plume. A much smaller but distinct plume of water with high heavy metal concentrations and 226Ra in the range of 10 to 130 pCi/L extends from beneath the dam for a distance of 15 m. The pH of the groundwater in this heavy metal-radium plume is 4 to 5, whereas elsewhere in zone of groundwater with high dissolved solids, the pH is above 6. The results of this investigat, suggest that the heavy metals an 226 Ra are relatively immobile in the perme-

Jan 1, 1980

By D. Malhotra

Climax byproduct-plant tailing assayed 0.019 percent WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The paper discusses the methodology used in the study and the results of this investigation.

Jan 1, 1985

By T. van Sandwijk, G. Van Weert, E. Molleman

This paper reports on test work that explored the dissolution/precipitation reaction: ZnS + 2HCl - ZnC12 + H2S, which is part of a process used in the production of pure ZnS. The research focused on the influence of proton activity on the dissolution of zinc concentrates obtained from the Brunswick Mine No. 12 in Canada (Brunswick Mining & Smelting); the Red Dog deposit in Alaska (Cominco Ltd.); and the Tara deposit in Ireland (Outukumpu Zinc). A comparison between the results of the experimental dissolution as a function of pH and the dissolution predicted by thermodynamics suggest that the three concentrates contained sig¬nificant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1999

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By Michael L. Nave

Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry.

Jan 1, 1993

By Pradip

Chelatang agents, because of their metal specificity, can function as effective mineral processing reagents. A brief review of the work carried out in this area is presented. Some of the salient features of mineral flotation and flocculation with chehting-type reagents, such as bulk us. surface chelation, the role of pH, mineral solubility, solution chemistry of reagents, and temperature, are illustrated with appropriate examples. The problems associated with the commercialization of chelating reagents for ore beneficiation and the research efforts required in this area are also discussed.

Jan 1, 1987

By André G. Journel

As opposed to graphics applications in medical sciences and mechanical engineering, computer imaging of the subsurface faces a severe problem of data shortage. Most graphics softwares include an interpolation algorithm aimed at producing slick graphic output, irrespective of the attribute being interpolated, the quantity and quality of the data available, and what the map is intended for. It is suggested that the power of modern computers be also used in providing representations of the subsurface that accurately reflect actual spatial variability and the large variety of soft information available beyond hard data. Since any subsurface representation is uncertain, a measure of that uncertainty should be provided which can be used for risk analysis.

Jan 1, 1992

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By R. R. Oder

Reported are weight, particle size, gross chemistry and magnetism measurements for lithic, mineral and fused soil components separated from five lunar soils using dry, open-gradient, magnetic separation. Pure diamagnetic anorthite, a feedstock for the electrochemical separation of oxygen and metals, has been separated from anorthistic highland soils. In addition, paramagnetic ilmenite has been separated from high-titanium, basaltic mare soils. Ilmenite, a feedstock for oxygen preparation by hydrogen reduction, may also serve as a source of He3 for use in fusion power generation. Agglutinates (vesicular, glassy components containing metallic iron) have been separated from all of the soils. Iron and refractories can be used for space construction. Metallic iron is easily detected in lunar soils by magnetic susceptibility measurements. Based on the exploratory laboratory results, conceptualizations of innovative magnets for processing lunar soils are presented.

Jan 1, 1993

By Arthur J. Borst, Joseph P. Gildner

In a recent National survey, Seattle topped the list for having the worst daily traffic congestion. To address this problem, Sound Transit is planning to build 40km (24 miles) of light rail, including ten kilometers (six miles) of twin tunnels with four subway stations 40 m (130 ft.) to 65 m (210 ft.) deep. The overall schedule is very aggressive and Sound Transit is preparing four separate heavy civil construction contracts for simultaneous underground construction. Three of these contracts are being considered for design-build. Final design will start in March2000 and all underground construction must be completed by the end of 2005.

Jan 1, 1999

By E. D. Sehnke

The refractory materials industry provides the largest commercial market for nonmetallurgical grade bauxite. Refractory grade bauxite is prepared from bauxites having low iron, titania, and alkali content by calcining at temperatures near 1,650° C. Although there are substantial bauxite reserves in the world, premium grade bauxite ores suitable for use in refractory applications are limited to only a few specific sources, primarily in Guyana and the People&apos;s Republic of China. Consumption of bauxite for refractory use is closely associated with the production and consumption of primary metals, in particular iron and steel. Barring major disruptions within the principal producer nations, sufficient supplies of refractory bauxite will be available to meet world demand well into the next century, and raw material costs will continue to determine the availability of markets for bauxite-based refractory products.

Jan 1, 1992

By D. A. Dahlstrom

With today&apos;s high energy costs per million BTU&apos;s, far greater emphasis is placed on increasing thermodynamic efficiency in the use of energy. America has long since discarded its previous golden age of "low cost energy" in the past ten years. Energy costs are now a very significant percentage of operating expense in industrial operations. Public utilities have felt the same influences of increasing costs in energy for the generation of electricity. Not only has the input energy expense increased seriously, but as pointed out by Blackmore in a paper, fuel costs were 53.4% of the total operating costs for American Electric Power Company.

Jan 1, 1983

By R. P. King

Direct observations of intergranular fracture during comminution are very difficult to make. The best indirect method is based on the measurement of interphase area before and after comminution. If intergranular fracture does not occur, the interphase area should be conserved during comminution, but it should decrease if significant amounts of intergranular fracture occur. The interphase area per unit volume can be determined by image analysis from measurements on sections of the unbroken ore and on sections through the particles after comminution. However, the measurements must be corrected for the effects of image resolution on the measured phase and particle perimeters. A correction procedure was developed, and the true interphase perimeter per unit volume was measured before and after comminution in a sample of chromite-serpentinite ore and two samples of Witwatersrand pyritic quartzite. The pyritic quartzite showed no significant evidence of grain- boundary fracture while the chromite-serpentinite showed a significant decrease in interphase area per unit volume of chromite, indicating that intergranular fracture occurred.

Jan 1, 1992

By Andrzej Wala

Constantly increasing demand for energy materials and metal ores brought about tremendous progress in mining techniques which are characterised by a high degree of mechanization and concentration of works. One of the recent trends in underground mining mechanization is connected with an application of heavy machines with diesel engines [l],[2]. The introduction of diesel engines in mining all over world caused not only improvement in economic conditions but also the necessity to prevent contamination of air in the mine by toxic agents in diesel exhaust emissions. A generally used way of eliminating exhaust gases is proper ventilation of the cross cut by means of providing permanent exchange of air that would guarantee in every point of the cross cut and in every moment the decay in concentration of exhaust gases beyond threshold limit [3][4][5][6][7][8][9][10]. The present paper is an attempt to define a mathematical model describing the changes of concentration in cross cut face to which fresh air is distributed by ventilators and tubes in a forcing way. Obtained model should offer its practical adaptability to engineering calculation of the amount of fresh air needed for diluting and eliminating exhaust gases beyond threshold limit. Justness of these models has been confirmed by investigation of the growth of nitrogen dioxide concentration in air environment in some cross cut faces of Kiirunavaara iron ore mine in Kiruna (Sweden).

Jan 1, 1980

By D. H. Dvorak

Two pilot-scale biological reactor systems were installed to treat metal-contaminated water. The reactors consisted of barrels and tanks filled with spent mushroom compost, within which bacterial sulfate reduction became established. Concentrations of Fe, Zn, Mn, Ni, and Cd were lowered by over 95% as these metals were precipitated as insoluble sulfides by reaction with bacterially generated H2S. The chemistry of the reactor systems is examined, and opportunities for maximizing their metal-retaining and alkalinity-generating potentials are discussed.

Jan 1, 1991

By W. C. Peters

Geologists take the role of mine geologist when they apply their science to the design and operation of a specific minerals project. In doing so, they use the entire spectrum of procedures in economic geology and engineering geology to deal with a specific system of orebodies and associated environment. The objectives are established by stages in the life cycle of a mining operation as it goes from a prospect to a development project and on to a mine. This paper summarizes the elements of a mining geologist&apos;s role, with examples highlighted from the preceding papers.

Jan 1, 1992

By Randy Sandrik

Sampling has evolved at two large underground limestone mines as conditions and product requirements have grown tougher over 100 years of mine life, requiring innovative techniques to insure delivery of high purity limestone. Sampling insures delivery of consistent product to customers at the lowest possible cost. Statistical considerations have evolved from simple data collection to predictive and process capability analysis. Sample methods include borehole samples, face (using a proprietary face-sampling device), and total plant feed automatic, process, and final product sampling. Lessons learned, while keeping costs at historically low numbers, include the importance of geological models, exploration drilling density, face sampling, and blending of ore.

Jan 1, 2005