Search Documents

By P. Mousset-Jones, G. Danko

Rock thermophysical properties, i.e. heat conductivity and thermal diffusivity, were obtained for reference values at the Waldo Test Mine for mine fire simulation purposes. An in situ measurement method was chosen since it could include the effect of rock fractures. The REKA method (Rapid Evaluation of k and alpha) was used because it can measure conductivity (k) and diffusivity (alpha) simultaneously within an eight-hour measurement period. A total of six measurements were taken in three different holes, and at two different depths from the collar of the hole. Each measurement provided an averaged conductivity and diffusivity for a volume of rock of approximately one cubic meter. The boreholes were driven into the upper and lower limestone, two at right angles to and one parallel to, the stratification of the rock. Significant representative conductivity and diffusivity values were obtained for the whole mine by averaging the six measurement results. The thermal properties for the band of shale in between the two limestones were not measured in situ, but only in the laboratory. Problems were encountered in the evaluation because of unexpected heat conduction on one side of the symmetrically built probe. A modification was made to the previously developed evaluation method together with further testing and correction, before the final results were obtained. As expected, the in situ and lab- oratory measured values of k and alpha compared favorably, since the in situ rock was dry and relatively unstressed.

Jan 1, 1989

By Christoph Wels, Michael Royle, Shannon Shaw

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2000

By Christian Jeger

After recalling the principles underlying fire-damp flow in coal and the essential part played by permeability (Darcy's law) in the intensity of flow, a few theoretical and experimental results showing the possible causes and range of variation of coal seam permeability are presented. The study of firedamp flow into gate roads and of residual gas concentrations in coals as a function of the gate road distance, shows that, in French mines, coal seams in a virgin zone have a very low permeability, but they become permeable when destressed by mine workings, in particular overlying workings. This is the case not only in the fractured zone round a mine excavation in which the gas is released, but also beyond the limit of the zone degassed by the excavation. In the floor of flat seams, upward boreholes can be used for predegassing seams that have been relaxed but not degassed, as the result of an overlying coal face. In this respect we shall describe the predrainage experiment carried out in the Marienau district of the Lorraine coalfield. Predrainage can contribute considerably to the reduction of methane emission in the ventilation of newly opened longwall faces. But to be efficient and useful predrainage should meet certain conditions.

Jan 1, 1980

By Al. Valero

This paper quantifies in universal units (energy units), the annual decrease in the mineral endowment of the planet. This is done for some important extracted non-fuel minerals, namely aluminium, cobalt, chromium, copper, gold, lead, uranium and zinc and is compared with the depletion figures of conventional fossil fuels. The results of this study reveal that each year, the decrease of the global non-fuel mineral bonus provided by Nature is 2 to 3 orders of magnitude greater than the loss associated to the burning of fossil fuels. Particularly for 2008, the depletion in mineral wealth of the studied commodities was about 20 times greater than that of fossil fuels. The assessment methodology is based on the Second Law of Thermodynamics. It quantifies the useful energy (exergy) required to concentrate a mineral from a completely dispersed state in the crust, to the conditions of composition and concentration found in the mines. Exergy can be a useful measure for quantifying the mineral depletion caused by man, as it takes into account the main physical features that make minerals valuable: composition and concentration. This analysis enhances and puts numbers to the importance and necessity of material reuse and recycling.

Jan 1, 2011

By Frank R. (Original by) Barnako

Coal mining historically has been a hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work.

Jan 1, 1981

By Walter E. Jaworski, William R. Beloff, John Dunnicliff

As a step in the endeavor to reduce future tunneling costs in New York City, the Environmental Protection Administration, Dept. of Water Resources, instituted a program in 1972 to monitor the performance of the lining of one of its tunnels. A monitoring program was included as part of the contract specifications for the East Branch Interceptor Sewer tunnel for the Port Richmond Water Pollution Control Project in the hope that measured data would indicate possible future cost effective design or construction improvements. The monitoring program involved measuring ground deformations, circumferential liner stresses, longitudinal liner stresses, and jacking pressures. This paper presents some of the findings from these measurements, with emphasis on liner stresses. PROJECT DESCRIPTION The 3.05m (10 ft) diameter steel lined tunnel was constructed under two separate contracts. The easterly portion, Contract 3A, was approximately 3109m (10,200 ft) in length and constructed by Peter Kiewit Sons Co.1 The westerly portion, Contract 3B, was approximately 2160m (7100 ft) in length, and constructed by Richmond Constructors, a joint venture of Grow Tunneling Corp., MacLean Grove & Company, Inc., Grove, Shepherd. Wilson & Kruge, Inc., Morrison-Knudsen Company, Inc., and Andrew Catapano Co., Inc. Each contract included three test stations, hence a total of six along the tunnel route. Excavated material along the tunnel route consisted primarily of dense fine to coarse sand with varying percentages of gravel and silt with occasional boulders. Pockets of organic silt were encountered on Contract 3B and a large portion of Contract 3A ran through slightly weathered serpentine and schist. Overlying material and the groundwater level varied considerably along the route as did the height of overburden. Figures 1 and 2 show the generalized soil profiles for Contracts 3A (PK stations) and 3B (RC stations) respectively.

Jan 1, 1979

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By Wenbing Guo, Mingjie Guo, Hebing Zhang

As resources are depleted in coal mines, isolated support pillars are often mined. Cemented paste backfill has been used to provide support during the mining of these pillars due to its safe and green mining characteristics. However, traditional cemented paste backfill mining has some shortcomings, such as poor adaptability to geological structure, leakage of paste during filling, imperfect roof-contact in partially backfilled areas, and insufficient roof strata support before the backfill reaches its design strength. This paper presents the results of a case study where L-shaped interval cemented paste backfill technology has been safely used to mine an isolated coal panel beneath existing surface structures. This backfilling method has the advantages of preventing paste leakage, improving the backfilled ratio, reducing surface subsidence, and strongly adapting to geological structure. During this field application, the setting pressure of the backfill shield reached 20 MPa, the compressive strength of the backfilling body reached 2.0 MPa, and the backfilled ratio reached 93.7%. Observational ground monitoring showed that roof-to-floor convergence in adjacent roadways ranged from 132 to 167 mm. No obvious fractures or separations in the overlying strata were observed by a borescope. The maximum surface subsidence was 342 mm, the subsidence factor was 0.136, and the damage to surface buildings was within Grade I (slight damage). This case study clearly demonstrates that the L-shaped interval cemented paste backfill method can be safely used to mine the isolated coal panel beneath surface buildings.

Jul 1, 2023

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

By Kot F. v. Unrug

In spite of extensive research and accumulated experience from mining operations, appropriate coal strength values for pillar design remain debatable. Coal strengths determined in the laboratory on standardized samples vary widely among various coal seams with poor repeatability. Penetrometric in situ strength testing obtains multiple measurements at multiple horizons within the coal seam to provide a strength profile. Alliance Coal has used that method in many of its mines for pillar design. Pillars in these mines perform well. This paper presents a series of case studies and discussion of issues related to coal pillar design. The analysis demonstrates that the proposed default in situ strength of 900 psi is appropriate when no other data exist. However, in the case of appropriate strength measurements combined with analysis of pillar structural composition, differing values can be used successfully. In areas where the penetrometric derived in situ strength is greater than the standard 900 psi in situ strength, reserve recovery has been optimized as required by law without compromising safety.

Jan 1, 2009

By R. P. King

INTRODUCTION It is now 21 years since Wiegel and Li published their paper on a random version of Gaudin's model for the mineral liberation phenomenon (Wiegel and Li, 1967). This paper was to revitalise interest in North America in one of the most fascinating, difficult and important problems in the field of theoretical mineral processing. Gaudin had many years previously (Gaudin, 1939) already presented a penetrating analysis of the problem and Wiegel and Li based their analysis very closely on the Gaudin model but they realised that the indeterminate geometrical structure of mineralogical materials demanded that only probabilistic models could provide the necessary quantitative information when working with real materials. They proposed and solved a randomised version of the Gaudin model but retained the essential geometrical simplicity of cubic mineral grains and a cubic fracture pattern. Although their model met with some limited success it was to be superseded in due course. During the 1940's and 1950's the classical field of geometrical probability spawned the mathematical discipline of integral geometry and as early as 1965, Bodziony (1965, a,b) showed that the techniques of integral geometry could accommodate the problems associated with the indeterminate nature of the geometrical mineralogical structure, provided that these were couched in probabilistic terms. In particular he showed that the quantitative description of the comminution process and that of liberation could be decoupled with the resulting economy of effort. This idea has profoundly influenced the course of research in liberation theory and has greatly facilitated its application and the measurement of liberation in a practical way. Bodziony demonstrated also that any theory that required the specification of the mineral "grain

Jan 1, 1989

Microwave pretreatment can improve grindability by weakening brittle particulate material prior to size reduction. The differential thermal expansion experienced by multiphase materials during rapid heating can also promote damage in the grain-boundary region, which may ultimately translate into enhanced liberation. The effect of microwave pretreatment on the breakage characteristics of different ores has been studied using the Ultrafast Load Cell. The energy accumulated during impact (fracture energy) and the particle stiffness have been measured for untreated and microwaved ore samples. It has been observed that microwave pretreatment can weaken brittle multiphase particulate material, as observed by reductions in fracture energy and increase in damage.

Jan 1, 1996

By Bartłomiej Bursa, Paweł Stefanek, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

The article presents the main functionality of the DSS class system for monitoring and stability assessment of tailings storage facilities. The presented demonstrator was deployed on the example of the Żelazny Most reservoir - the largest active facility of this type in Europe and the second one in the world. Considered a high-risk structure, it demands a system capable of online analysis of big data from various sources using machine learning, 3D modeling, or GIS mapping with the functions of interactive time-spatial analysis. In this paper, we present a complex calculation module with an integrated user interface.

Jun 25, 2023

By R. W. Wotring

Mr. Chairman, Officers, Members and Guests of the AIME, I want to express my appreciation for the privilege of being on your program at this meeting. Coal mining, in recent years, has become much more competitive than it formerly was. To stay in business, it has been necessary for coal mines to mechanize. This, in itself, has not been enough for after one has mechanized his mine, he must keep replacing the equipment with the latest type and model machines. We, at Olga, have been doing this very thing for the past several years. Olga No. 2 Mine is located at Caretta, West Virginia, in McDovell County, about twelve miles south of Welch, It is a shaft mine, operating in the No. 4 Pocahontas seam. The thickness in the area, we are presently mining, varies from five to six feet. In some areas the immediate roof is slate, ranging in thickness from a few inches to four and five feet; in other places, the sandstone lies on top of the coal, This sandstone is about twenty-five feet thick.

Jan 1, 1961

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

By J. Loredo

Asturias, in northern Spain, emits 18 Mt CO2/year to the atmosphere, which supposes the biggest industrial CO2 emissions in the country. In order to avoid CO2 emissions to the atmosphere, keeping the availability of energy from fossil fuels, background studies focussed to the selection of favourable sites for CO2 geological storage are necessary. In Asturias, the options for CO2 geological storage are sequestration in deep saline aquifers or sequestration in unexploted coal beds. In the area, there is the biggest coal basin of the country and a great Palaeozoic sedimentary basin with appropriate silicoclastic or carbonated reservoirs and impermeable caprock for CO2 geological storage, located in proximity to thermoelectric power plants and other sources of CO2 emissions. All evidences suggest that CO2 storage in deep aquifers is the most interesting option but a legal planning and a technical regulation are still to be done. The possibility for CO2 sequestration in coal beds is modest and associated to the CBM commercial exploitation. It is necessary to have in mind that the feasibility of CO2 geological storage in Asturias apart of technical factors will depend on price of CO2 ton, legal conditioning and possibility to apply emission rights to projects.

Jan 1, 2006

By M. Henneman, M. Kosma, M. Eyll-Vetter

"For a long time, the recultivation of depleted opencast mines and operating systems was aimed at restoring the original state. The focus, as desired by policy-makers and the local population alike, was on restoring high-quality agricultural land and on creating reforested areas of value that suit their location. Until the turn of the millennium, recultivation measures were only rarely the subject matter of public planning processes beyond these general objectives. They were never regarded as nucleus and origin of sustainable structural developments. The rehabilitation of inactive lignite opencast mines in central and eastern Germany brought about a change in mind-set that understood recultivation to be a unique opportunity to completely redesign a landscape and gear it towards the future in the Rhenish mining area as well. The ""Inden residual lake"" and ""terra nova"" projects, planned in the last 10 years in cooperation with policy-makers and authorities, are two undertakings that provide sustainable structural impetus for the future today."

Jan 1, 2011

By Ezra L. Kotzin

Foundry sands used to make molds and cores have been very important to foundrymen since metal casting began hundreds of years ago. They are now used in two basic ways, either in an uncured green state, grain-bonded with clay, or in a set cured state achieved with sand that, mixed with resins or oils, is cured by baking or by chemical reaction. The term sand, as generally used in foundry applications, may best be defined as material composed of granular particles of mineral matter, ranging in size from 0.5 to 2 mm in diameter. The particulate nature of the material may be the result of natural disaggregation or result from crushing and screening of rock or ceramic materials; crushed and screened products are sometimes referred to as "manufactured sand." Based on their origin, the raw materials for foundry sands will vary in grain shape, grain composition, relative surface, grain size, and grain distribution patterns. These properties, in addition to their chemical analyses, sintering point and expansion characteristics play an important part in the choice of sands used as the base molding or core aggregate in metal casting. Sands with different origins may be blended to produce specific compositions and grain size distributions. Early raw material requirements based on silica sand were simple, but as sand/core/mold technology became more sophisticated and binder technology continued to be developed, the physical properties of foundry sands became more critical. Silica sand is composed of quartz, along with, in most cases, small amounts of feldspar, mica, clay, and other common minerals. Although silica sand is still by far the most widely used base material in production of molds and cores used in metal casting, other natural mineral sands have their own unique characteristics and fill an important niche in special applications. As a result, the term sand, as applied to raw materials used in metal casting, has been logically extended to include granular materials composed of a group of minerals other than quartz. With increased use in advanced foundry technology, natural sands composed predominantly of zircon, chromite, staurolite, or aluminum silicate minerals and of granularized chromite or olivine, have become more than just alternate materials and are now commonly classified as sands when the grains are sand-sized. Foundry sand may therefore be considered under two categories: silica sands and non-silica sands.

Jan 1, 1994

By R. C. Fox

The geophysical aspect of reconnaissance marks the beginning of extensive computer applications supporting development of a mine. Although there are some storage and retrieval applications in geology, and some statistical analysis in geochemistry, large-scale compilation, reduction, and interpretation of mineral resource data are initiated in reconnaissance geophysics. The reasons for this fact are quite simple. Geophysics is oriented toward quantitative evaluation of areas of interest, and methods of data collection are automated to the extent that large amounts of analog and digital information are recorded. The large volume of data must be interpreted in a reasonable time. Furthermore, some modeling problems involving complex numerical solutions could not be attempted without the computer. Therefore, the computer is essential to the success of an exploration project using geophysics. For example, aeromagnetics is a common technique for reconnaissance examination of areas associated with sulfide systems and porphyry deposits. An area covering 161 X 161 km (100 X 100 miles) may be flown with a 1.6-km (1-mile) line spacing yielding 10,000 line miles (16,093 km) of data. If only 10 measurements are recorded per mile, 100,000 data points, including location and magnetic field intensity, must be reduced and stored for quantitative interpretation. Computer applications often represent a significant investment in manpower and hardware. It is desirable, therefore, to initiate an engineering approach to the application of computers to geophysics. By this it is meant that computer programs and systems should be formulated, developed, and implemented in a disciplined manner such that their usage is dependent only on the application and not on the individual doing the programming. In other words, computer application, development, and usage should evolve beyond the personal gadget phase to an important applied technology. Geophysics has evolved over the past two decades in a course parallel to computer hardware development. During the sixties, the computer became large enough and fast enough that complex models required by geophysics could be solved. Automation also relieved the geophysicist from routine manual calculations. During the seventies, computing power in¬creased and applications expanded from two-dimensional problems to three-dimensional modeling. Moving into the eighties, as computer hardware costs will significantly decrease, the major expense of computing will be the manpower required to develop, implement, and use an application; therefore, improved programming techniques and applications software engineering methods will be used to optimize and preserve this investment. This chapter presents a general overview of computer methods in geophysical reconnaissance; it is divided into two parts: geophysical methodology and software engineering.

Jan 1, 1979

By D. A. Huggins

Column flotation is finding increasing use in the flotation of copper, molybdenum and other heavy metals and coal. Columns have proven operational, cost and metallurgical advantages which caused us to investigate their use in the proposed Escondida flowsheet. A comparative pilot plant test with 35 tons of ore showed that one column can replace three stages of cleaning and result in a significantly higher concentrate grade with no loss in recovery.

Jan 1, 1987