Search Documents

By Robert Sutton, Milan Sjaus

Conveyor pulleys are an important and integral component of a conveyor. Conveyors work in sequence to make up conveyor systems. Each conveyor system is only as reliable as its crudest component. If the pulley fails, then the whole material handling system stops. So what is the effect of this downtime? What are the costs of repair? How much are we willing to pay to solve the problem? What should we spend to prevent an unscheduled shutdown? Do we use the technological improvements at our disposal or do we ignore them to satisfy immediate cost savings? This study will focus on the cost of pulleys relative to the total conveyor cost, the cost of downtime, the maintenance costs and the costs for resolution of the problem. Some philosophic and design concepts are injected for illustration and discussion.

Jan 1, 2000

By J. Pang, S. Chander

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and impedance spectroscopy techniques. The cyclic voltammetry was used to elucidate oxidation/reduction reactions, whereas impedance spectroscopy was used for in-situ characterization of the interface. To analyze the impedance spectra, equivalent circuit models were constructed based on a layer- wise growth of reaction products. Parameters of the equivalent circuit were calculated by comparing the experimental spectrum with that expected on the basis of equivalent circuit. From the value of equivalent circuit parameters, properties of the surface layers were inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution. From such changes the effect of oxygen and collector concentration on the contact angle and flotation behavior of chalcopyrite were interpreted.

Jan 1, 1991

By J. M. Kruger

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially-intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom-shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1997

By D. C. Wilder

Deformations during heating and cooling of three drifts in granitic rock were influenced by the presence of faults and shear zones. Thermal deformations were significantly larger in sheared and faulted zones than where the rock was jointed. but neither sheared nor faulted. Furthermore. thermal deformations in faulted or sheared rock were not significantly recovered during subsequent cooling thus a permament deformation remained. This inelastic response is in contrast with elastic behavior identified in unfaulted and unsheared rock segments. A companion paper (Butkovich and Patrick, 1986a) indicates that deformations in un- sheared or unfaulted rock were effectively modeled as an elastic response. We conclude that permanent deformations occurred in fractures with crushed minerals and fracture filling or gouge materials. Potential mechanisms for this permanent deformation are asperity re-adjustments during thermal deformations. micro-shearing, asperity crushing and crushing of the secondary fracture filling minerals. Additionally, modulus differences in sheared or faulted rock as compared to more intact rock would result in greater deformations in response to the same thermal loads.

Jan 1, 1986

By Donald D. Haas

This presentation will discuss a mine owner's evaluation to utilize a contract miner in the development and production of gold properties. I will address both the quantitative and subjective aspects of the evaluation process. The quantitative aspects include cost evaluation, capital preservation, acquisition and disposal of new and used equipment, administrative costs, recruiting and training, and organizing a staff and craft labor force. The subjective areas of this discussion include corporate philosophy, administrative concerns, contractor competence, loss of owner control, operating flexibility, financing assistance, recruiting and training program utilization and risk reduction. The evaluation of alternatives provides a system for comparing, on a cost basis, an owner/operator system vs. a system using a contract miner. The supplement provides a concept on how a contract miner may be the cost effective system to be utilized.

Jan 1, 1989

By Salama

In the conventional approach, the separator feed incremental masses are assumed to be concentrated at the midpoints of the density or size intervals and subjected to a model partition function. The resulting separation predictions would change if the locations of the incremental masses were changed. As a result. the predicted results depend on the choice of locations where the feed incremental masses are concentrated in the density or size intervals. A technique that utilizes the cumulative-mass-distribution of the circuit feed and the derivative of the partition (separation) function relative to density or size variables is proposed. The proposed technique eliminates the dependency of the predictions on choice of where the feed incremental masses are concentrated within the density or size intervals. Since the proposed technique is based on the cumulative masses at the upper limits of the density or size intervals, the technique produces a single prediction whereas the existing techniques produce predictions that depend on where the incremental masses are concentrated. In fact, it has been demonstrated that the existing conventional technique, in which the incremental masses are concentrated at the midpoints of the density or size intervals, is a first-order approximation of the technique proposed.

Jan 1, 2002

By N. S. Tanious

The accuracy of vibrating wire stress meters has been questioned by various users in the mining industry. During an in situ coal pillar study, a laboratory evaluation program was developed to determine whether stress meters could produce reliable measurements in coal. More than $0 stress meters were tested for accuracy, repeatability, effects of setting pressure, and the concept of using a single curve for interpreting the stress-meter data. The testing medium was lucite, a material with a modulus of elasticity very similar to coal. The evaluation demonstrated that the stress meters did provide repeatable measurements, but that accuracy was lacking when the recommended interpretation technique was used. Therefore, a new technique was developed that required all stress meters to be calibrated in the laboratory before use in the field. This new technique reduced the average error to typically less than 10% and, in the worst case, to below 15%.

Jan 1, 1988

By W. A. Steingraber

This paper discusses the application of deep well disposal techniques to the problem of disposing of large volumes of low level radioactive wastewaters generated by the in situ uranium mining industry in Seth Texas. Data is presented on wastewater composition and volumes, geologic and hydrologic parameters of the disposal reservoirs, tell construction techniques, well operation, well monitoring requirements, and critical factors in evaluating the Safety and environmental impact of a deep injection well system.

Jan 1, 1980

All coal preparation unit operations in which fine coal is handled depend to some extent on wettability of coal surface by water. The wetting results from interactions between the coal surface and water molecules that are determined by the composition of coal matrix (interrelated with coal rank) and heterogeneous constituents such as oxygen functional groups, mineral impurities and pores. The contact angle of water on an unoxidized, homogeneous coal hydrocarbon matrix is calculated to be 100o, and much lower values measured on real coal specimens result from contributions from the heterogeneous constituents. While the effect of wettability is critical in flotation and oil agglomeration, suppression of respirable dust, and coal water fuels, it has been shown to play a significant role also in coal flocculation with semi-hydrophobic and totally hydrophobic flocculants.

Jan 1, 1995

By E. M. J. A. Pallone, F. N. Cunha, W. S. Resende, R. M. Stoll, R. C. Bradt

Utilization of the magnesium aluminate spinel in refractor' applications is briefly reviewed. The synthesis of a magnesia aluminate spinet aggregate from natural raw materials is considered in terms of the crystal chemistry of the spinet structure and expected impurities. Principles for the formation of this spinet refractory aggregate from different natural raw materials are presented. The basic concepts were then applied to the reaction of a bauxitic clay with a natural magnesite. This combination of raw materials has the potential to produce a low-cost refractor' aggregate that is a composite of spinel and forsterite. Experimental results are reported to produce a spinel refractor.' aggregate containing a small amount of forsterite. It possesses low apparent porosity and high bulk density suitable for industrial refractor' applications, including steelmaking, aluminum and copper foundries and cement production.

Jan 1, 2002

By I. Iwasaki, K. A. Smith, X. Cheng

The reaction mechanism for the cathodic decomposition of pyrrhotite in deoxygenated solutions at natural, near neutral pH levels was studied using potential and cyclic voltammetric measurements. Reaction products on the pyrrhotite surfaces were examined by Auger Electron Spectroscopy (AES), by X-ray photoelectron spectroscopy (XPS) and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using an ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least-squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by performing microflotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1995

By R. A. Bergman, P. G. Thornhill

Development of the Falconbridge Ferronickel Process for treatment of lateritic nickel ores began with laboratory work in 1955, the year the Company commenced exploration of its concession in the Dominican Republic. Process development centred on selective reduction originally directed to producing calcines amenable to ammonia leaching, but later found suited to electric smelting. The reduction step of the process was developed in a 25 tpd shaft furnace pilot plant located in the Dominican Republic, to which was later added an electric melting furnace. After almost 3 years of development work on this scale the plant was expanded to 100 tpd for fixing design data for a commercial plant. This took the form of the 30,000 ton per year Nickel Ferro-nickel Complex of Falconbridge Dominicans, which started up in 1971.

Jan 1, 1979

By J. B. Zachwieja

Cationic reagents have been utilized in mineral processing since the mid 1930's and are based upon fatty nitrogen derivatives. The initial commercial development was centered around a flotation collector capable of separating potassium chloride from sodium chloride - potash flotation. The first commercial sale for Akzo, known then as Amour and Company, was realized in the summer of 1940 to a potash producer in Carlsbad, New Mexico for the flotation of potash. The success of the potash flotation collector led to the development of other cationic mineral processing reagents. Flotation collectors for iron ore, phosphate, calcium carbonate, silica sand, feldspar, and other silicates materialized into a large commercial business. Another area that realized commercial success was the development and use of anticaking/antidusting reagents for hygroscopic salts, fertilizer mixes, and granular fertilizers. A more recent development has found use in the trona industry as a defoamer and crystal growth modifier during the crystallization of sodium carbonate liquors. A review of cationic reagent chemistry and applications will be given and the potential for new application areas will be explored.

Jan 1, 1994

By R. Hogg, P. Bunnaul

Sedimentation in highly, flocculated suspensions of fine particles, such as clays, occurs through individual settling units (flocs) that have very open structures and correspondingly low densities (typically less than 5% solids by volume). Such settling processes rapidly lead to the buildup of a bed of flocs that are essentially close-packed, with an inter-floc porosity of perhaps 50%. However, the overall solids content is no more than about 2% to 3% by volume. Consequently, the thickening process is dominated by the bed consolidation rather than by the simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate, for a given system, that consolidation rates are essentially determined by the solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical, as well as the chemical, conditions of the flocculation process. Furthermore, the extent to which gravity consolidation proceeds depends on the total weight of the sediment (i.e., on the bed height and the solids concentration). The implications with respect to thickener operation and the requirements for the laboratory testing for thickener design are discussed.

Jan 1, 1993

By S. A. Matthews, M. L. Nave

AC variable frequency motor drives are emerging technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of drive, motor, and conveyor features. The purpose of this paper is to familiarize and inform possible mining users of AC variable frequency drive attributes.

Jan 1, 1998

By F. M. Doyle, S. Duyvesteyn, K. Sreenivasarao

Toxic metals entering surface or ground water from sources such as metal finishing shop spills and abandoned mines can pose a significant threat to public health and the environment. Ion flotation and similar foam separation techniques show great promise for treating dilute, metal-contaminated solutions, and could also be used to treat effluents from many minerals and metallurgical processing operations prior to discharge. In ion flotation, an appropriate collector is added to the solution to form hydrophobic complexes with the metal ions. These metal-bearing species are then removed by flotation, usually with trace addition of a frother to stabilize the foam. In an effort to better understand the underlying scientific and engineering principles that determine the performance of ion flotation, the removal of Cu(II), Pb(II), Cd(II), Cr(II) and Cr(VI) has been studied using laboratory scale flotation columns in batch mode. The effects of the superficial air velocity, solution and froth height, nature of the collector, collector: metal-ion ratio, ionic strength and several frothers at low concentrations on the flotation kinetics are reported. Finally, results are presented on methods that might allow regeneration of collector and recovery of by-product metal from the foam product.

Jan 1, 1995

By A. Mehmet, W. A. M. te Riele

A pilot-plant investigation in a NIMCIX contactor has shown that activated carbon can extract more than 93% of the gold in return-dam solutions. The average gold concentration in the barren solution was less than 0.003 mg/L from a feed averaging 0.048 mg/L. The carbon was eluted by the Zadra procedure. The operating conditions of the elution-electrowinning circuit are reported, and the elution of the gold and other metals is discussed. The reactivation of the carbon by use of the Rintoul kiln is described, together with the results of reactivation. The consumption of reagents in the process cycle is presented in sufficient detail to allow the economic viability of this technique to he evaluated for the recovery of gold from low-grade solutions.

Jan 1, 1990

By P. Sander, M. Spiegl, J. Reilly, A. Van Droogenbroeck

Although the outdated idea of calculating risk as the deterministic product of its likelihood and impact is not entirely a thing of the past, a multitude of organizations have adopted the usage of probabilistic methods for risk analysis, as they better reflect the inherent uncertainty of cost and risk estimates with ranges. But are these advancements sufficient in a complex environment such as tunnelling projects, where inadequate modelling of cost and risk can result in estimate discrepancies that run into millions of dollars? This paper explores two advanced probabilistic modelling techniques for tunnelling projects. The first one demonstrates how the cost and schedule uncertainty related to changes in excavation and support classes can be modelled with correlated variables. The second example models the risk related to explosive ordnance clearance on construction sites using a probabilistic event tree.

Dec 1, 2022

By Enrique Jelvez, Nelson Morales Varela, Christian Ihle, Joaquin Silva

All mineral beneficiation processes require water for its execution. Therefore, the availability and adequate management of water are key to the existence of any mine operation. However, many mines’ operations are affected by water scarcity and risk an increase of operational costs or even production in some cases. This paper proposes a model to minimize the losses of water due to evaporation and re-absorption by adjusting the active and inactive periods of the discharge in different points of the tailing. When applied, the model determines optimal or nearly optimal discharge operation in all the scenarios that were evaluated.

Jun 25, 2023

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.