Search Documents

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By D. L. Purcell, B. T. McClure, J. McDonald

The U.S. Bureau of Mines has completed a laboratory evaluation of exhaust emissions from a diesel engine using an oxygenated diesel fuel. The fuels tested were soy methyl esters in a neat (100%) form and low sulfur, petroleum number 2 diesel fuel (D2). The engine tested was a Caterpillar 3304, indirect injection, naturally aspirated, 75 kW, diesel engine that is typical of engines used in underground mining applications. The objective was to determine the extent to which oxygenated fuels, such as methyl esters, reduce diesel particulate matter (DPM), and their influence on upon gaseous emissions such as total hydrocarbons, CO, NOx, NO2, formaldehyde, and other exhaust emissions. Heavy- and light-duty transient tests were used to simulate load cycles typical of mine applications. The soy methyl ester fuel produced greater amounts of volatile DPM (organic material) but much less nonvolatile DPM (carbon soot) for overall DPM reductions. A diesel oxidation catalyst (DOC) typical of the type commonly used in metal and nonmetal mines was tested with both fuels. The DOC further reduced the volatile and total DPM when used with the soy methyl esters, but increased the total DPM for D2 due to sulfate formation. The soy methyl ester fuel reduced CO and hydrocarbon, and NOx emissions. The DOC further reduced CO and hydrocarbon emissions.

Jan 1, 1995

By Sertaç Dündar, Bilgehan Kekeç, Arif Emre Dursun, Niyazi Bilim

"Estimation of rock drillability is vital for mining and boring operations. For this purpose, many researchers have developed various models and equations to estimate rock drillability. Most of these models aim to determine the drillability of rock and the penetration rate by using the physical and mechanical properties of rocks. Although drillability primarily depends on rock properties, other parameters have an impact on drillability as well. One of these parameters is the rotation speed of the bit. This study investigates the effect of rotation speed of the bit on drilling performance. Drilling tests were performed in the laboratory using rotary core drilling and a diamond drilling machine. The relationships between the physical rock properties and the penetration rate were investigated on 15 different rock types and four different rotation speeds were applied to determine the effect of rotation speed of bit on drilling. The uniaxial compressive strength, density, and P wave velocity show strong correlations with the penetration rate. In addition, if the values of the physical and mechanical properties of the rock increase, the effect of the rotation speed on the penetration rate decreases, i.e., increasing the rotation speed of the bit slightly affects drillability on hard and solid formations. 1. Introduction Drilling is one of the most essential operations in the mining industry, beginning from the exploration phase and continuing throughout all stages of production to the end of mine life (Taheri et al. 2016). In addition, drilling is widely using in the construction industry and other engineering operations. Various drillholes (blastholes, injection holes, borehole, diamond wire holes in natural stone mines, etc.), are needed during development and production activities in underground and open-pit mines as well as in dam, tunnel, road construction and sewage systems. For effective drilling operations, it is first necessary to gather information about the formation to be drilled. Drilling should then be performed after selecting appropriate drilling equipment and drilling parameters (thrust, pressure, rotational speed, flushing). Prediction of the drillability of rocks is vital for planning and performing the drilling process. Although, drilling is affected by several factors, the most important ones are related to the geological and mechanical properties of formation (Protodyakonov 1963, Paone et al 1969, Tandanand and Unger 1975, Pathinkar and Misra 1976, Rabia 1985, Perrin et al 1977). Determining the penetration rate is vital for planning a project and calculating the operation costs. The prediction of drilling affects the selection of drilling equipment, the efficiency of drilling equipment, project costs and the process of drilling operations."

Jan 1, 2017

By Euler De Souza, Jason Chew, Aldrich Philip Dirige

Sillmats are structural elements upon which the safety and economics of underfill mining or sill pillar recovery in stopes of moderate width with steeply dipping ore zones, depend. The traditional stability design of cemented sillmats appears to have developed from experience and from standard static physical model tests such as uniaxial and triaxial compression. Such standard static physical model testing approach arrives at some approximate parameters, normally used to describe or predict the behaviour of sillmats in analytical or numerical models. This approach offers inherent limitations and generally results in conservative designs. Centrifuge modeling studies are combined with numerical modeling in this paper to provide insights into sillmat strength behaviour. The results of both modeling techniques suggest that, in stopes with smooth rock wall conditions, sillmat failure is driven by the fill self-weight and has minimum dependency on the fill binder content. In stopes with rough rock wall conditions, however, the wall roughness contributes significantly to the stability of the sillmat during underfill mining. This study indicates that the stability of paste fill sillmats can be designed with confidence using centrifuge physical modeling in combination with numerical modeling.

Jan 1, 2001

By Robert H. Marshall

The application of simulation to production planning at a large, complex open-pit mining operation proved to be challenging and enlightening. The mine is divided into two separate pits and several dump areas which are served by the same truck fleet. The operating system consisted of shovels of two different sizes, wheel loaders, and a fleet of three different truck types moving material from seven source locations to ten dumping sites. The interconnecting haulroad network included many common segments. There were operating constraints unique to the system, such as: traffic rules; manpower limitations; shovel, material-type, and destination priorities and production limitations; and a unique, non-centralized dispatching method for truck distribution. The truck distribution was further constrained by the matching of trucks to shovels, loaders, and destinations by truck type. The gathering and transformation of input data as well as the evaluation of results and validation of the model were also challenging. Despite a high level of sophistication in production reporting, some input data were neither readily available nor backed by field observation. As a result, many innovative techniques had to be used to develop realistic input data and to validate the simulation results. Nevertheless, this case study definitely proved the feasibility of applying computer simulation techniques to short and long range mine planning and budgeting at a large, complex mining operation.

Jan 1, 1982

By [Miroslaw] M. Hajdasinski

The Payback Period (PBP) is one of the most widely applied project evaluation criteria 'in the mineral industry. As much as this criterion is liked by practitioners, it is also criticized by academicians who seriously question its validity. Inspired by this criticism, the author of this paper examines the classical definition of the PBP criterion, and formulates a new one designed for both investment and borrowing projects. It is demonstrated that the PBP, in its revised version, is free from all the shortcommings of the old one, and is fully compatible with the Net Present Value (NPV) criterion, as well as with all the other NPV compatible project evaluation criteria. Since the traditional approach to the comparison of mutually exclusive projects (MEP1s) by means of the PBP criterion has been incorrect, the paper also outlines the correct approach to this problem. Finally, owing to the fact that the PBP depends on the assumed interest rate, and using a specially developed computer program, the PBP is graphically presented, in six numerical examples, as a function of the interest rate.

Jan 1, 1989

By Giin-Fa Fuh, Sally A. Shoop

An instrumentation program was developed based on the results of an analytical study of the geomechanical effects of longer longwall face lengths. Boundary element simulations showed that longer face lengths can cause in- creased face convergence and an increase in the shear stresses in the immediate roof. Empirical design methods predict that longer faces will cause little effect on abutment stresses as long as the roof caving is well behaved. On this basis, a longwall face instrumentation program was designed with emphasis on the interaction between face support and ground response for optimizing face conditions. At a 600-foot (183 m) face, five midface shields and two headgate shields were monitored with vary- ing hydraulic pump pressure. The instrumentation included six convergence rods with linear potentiometers to measure canopy-to-toe convergence; fourteen pressure transducers to monitor leg pressures; and two portable data loggers. Similar instrumentation will be in- stalled on a 750-foot (229 m) face for comparison. The results from the 600-foot (183 m) face indicate that a ground reaction curve, as determined from the relationship between the sup- port set pressure and the roof convergence, can be used to optimize the support pressure to control convergence, the key element to ground stability in the face area.

Jan 1, 1986

By A. H. Morris, W. Harrison

1. INTRODUCTION Roadheaders have a shadowy origin - probably in Eastern Europe - but were introduced to Europe and the West by the importation of a Russian PK3 machine by the National Coal Board in 1961. A number of features rendered this type of machine an attractive tool for coal mine operators: its flexibility of operation, its combined cutting and loading ability, the opportunity it provided of making any shape of roadway, as well as its ability to cut some rocks. Encouraged and sponsored by the National Coal Board, the development of roadheaders was taken up in Great Britain, notably by Anderson Strathclyde and Dosco; in Europe, predominantly in numerical terms by Voest Alpine and Paurat. Over the 24 years since the importation of the first PK3, evolutionary development has taken place to the extent that machines are now available in many forms up to 120 tons in weight. Machine design has altered, partly as a result of increased power requirements and partly in line with the use of a ripping or a co-axial head. However, the basic concept remains: a boom containing a motor and transmission gear, with a driven cutting head at its extremity and capable of universal movement urged by hydraulic rams mounted on the boom turret and on the machine deck. Generally, the turret, hydraulic powerpack and all other necessary equipment are mounted on a chassis, which contains a discharge conveyor, the whole being carried on caterpillar tracks so that a complete machine entity is provided. Figure 1 shows how the weight, power and - non-proportionally - the cutting ability of machines have increased over the years. From

Jan 1, 1985

By Graham A. Mathieson

A detailed breakdown of capital and operating costs is an essential element in the planning and evaluation of any mining project. The OPCOST System was developed by Golder Associates to provide mining engineers with the facility to synthesize detailed cost estimates for all aspects of an operating or potential open pit mine. The system can also be applied to underground mines equally as well. Such estimates can be prepared at a variety of levels depending on the detail required by the project. The OPCOST System is a suite of computer programs linked through a common hierarchical data base. It simulates the thought and reasoning processes within the quantity takeoff and cost estimation phases of a mining project. The system was developed as a mining cost engineering tool on the basis that it would have to satisfy a variety of purposes, namely:

Jan 1, 1982

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993

By L. Sletmoen, P. Rocque, E. DeSouza

Plans for achieving planned production rates at the Red Lake Mine High Grade Ore Zone required that the mine ventilation system be upgraded. Time constraints required that only a site assessment of the mine ventilation system be performed followed by recommendations for providing adequate ventilation conditions at the production zone. This paper describes the engineering assessment, design and commissioning of the ventilation system upgrade for achieving increased flows at the high grade ore zone. The work was successfully achieved with minimal capital expenditures and disruption to the mining cycle.

Jan 1, 2003

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of ‘handling supplies or material, load and unload’ and ‘moving power cables.’ Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods – the mobile manipulator, the in-mine hoist, and a cable-handling system - being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

Jan 1, 2005

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By C. O. Brawner, A. Bellamy, D. S. Cavers

Pit slope designs at Nickel Plate Mine have used relatively steep interim and final wall slopes of 60 degrees overall. The rock is unusually strong and tough with most discontinuity sets being steeply dipping. An integrated program of monitoring and drainage has been used. Stopes of large extent which are generally unsupported occur on the property. For the most part, no deterioration of the stability of the stopes has occurred over the last 30 or more years. Mining methods through these areas have used a combination of fill s placed via VCR drop raises and crater blasting of the backs. One of the major challenges in mining through the stope areas is to maintain slope stability conditions and to reduce dilution of the higher value ore zones occurring immediately around the stope areas. The paper discusses geology, slope stability and mining methods at Nickel Plate Mine.

Jan 1, 1988

By Fathi Habashi

OXIDE ORES can be divided into two groups: 1) Simple oxides (Table 3.1). 2) Complex oxides. Those ores containing minerals composed of two oxides; an acid oxide (Cr2O3, Nb2O5, etc.), and a basic oxide (CaO, FeO, MnO), as shown in Table 3.2.

Jan 1, 1970

By J. Hoover

Real growth in the economy, increasing demand for electricity, and consumer stockpiling for a possible United Mineworkers of America (UMW) strike in October made 1984 a banner year for coal. Production and consumption climbed to record heights. Precautionary purchases brought inventories close to the peak levels of early 1981 when coal miners walked out for 72 days. Production slowed in the fourth quarter after labor and management concluded negotiations without a walkout. But output in every major coal producing state showed significant gains during the year US coal production totaled 807 Mt (890 million st) in 1984. This is a 13.8% increase over 1983 output. Lower production rates, principally in Appalachia, and sustained demand in the final quarter put downward pressure on coal stocks by the end of the year. Demand All market sectors experienced greater requirements for coal in 1984. Electric utility coal consumption increased 6.3%; exports climbed 4.8%; coke plants consumed 18.9% more coal; coal requirements in the other industrial sector expanded by 11.8%; and consumption in the residential/commercial sector rose 8.1%. Domestic consumption of coal reached a record 718 Mt (791 million st) in 1984. This is a 7.4% gain over the previous consumption high of 668 Mt (737 million st) in 1983. Electric Utilities The 4.6% increase in electric power generation in 1984 was coupled with expanding coal use relative to other energy sources. This resulted in a 6.3% rise in coal consumption, totaling 603 Mt (664 million st) for the year. Thirty-eight of 45 states where coal-fired electric power plants were operating shared in the 36-Mt (39 million-st) increase in electric utility coal consumption

Jan 5, 1985

By J. Kallioinen

Flotation of low grade Ni ores with serpentinite host rock tend to yield low recoveries of Ni With high MgO contents in the concentrate. The recovery can be enhanced by optimizing the sub-processes in the pulp and in the froth. The new OF-100 flotation cell has been designed to be adaptable to different feed fineness (Coarse, Fine). The losses can according the research conducted at Outokumpu's Hitura plant be substantially decreased by OF-100's new rotor and stator design and froth zone geometry. The froth residence time is used to adapt for feed particle size changes measured by the Outokumpu PSI- 200. Models for the behaviour of different particle Sizes in the sub-processes have been developed. The modified froth zone geometry and the capability of maintaining a froth of desired thickness allows efficient washing of the obtained concentrate producing low levels of MgO.

Jan 1, 1994

By Robert R. Brandom

The Boss-Bixby deposit is one of several iron deposits that occur in the Precambrian igneous rocks of southeastern Missouri. It differs, however, from all of those deposits by its significant contents of copper, cobalt, and titanium, and its close relationship with a basic igneous intrusion. Ore microscopic study of selected drill core samples has shown that the hypogene ore minerals are magnetite, hematite, chalcopyrite, bornite, covellite, ilmenite, rutile, sphalerite, cobaltian pyrite, carrollite, scheelite, and wolframite. Subsequent partial oxidation has formed martite, pseudobrookite, and anatase. Textural evidence indicates that two stages of iron and iron-titanium oxide formation were followed by the deposition of the copper-iron sulfide minerals and carrollite.

Jan 1, 1985

By Alden B. Carpenter

Brines (a solution containing more than 100,000 mg/l dissolved solids) in sedimentary basins are genetically related to evaporites in one of three ways: (1) dissolution of evaporite minerals, generally halite; (2) interstitial fluids in evaporites which are expelled from their source rock during compaction; (3) incongruent alteration of hydrous evaporite minerals (carnallite). Most brines of commercial interest originate as interstitial fluids in halite-rich rocks. These fluids are initially rich in magnesium, sulfate, and potassium but evolve in composition to an Na-Ca-Cl brine during their migration to their present host rock. A particularly important reaction in this process is: 2CaCO3 + Mgt+ = CaMg(CO3)2 + Cat (1a) This reaction reduces the magnesium content of the brine and ultimately converts it to a calcium-rich brine. The loss of sulfate occurs by two mechanisms. One of these is by direct precipitation as calcium sulfate (either as gypsum or anhydrite): Ca 2+ + SO4 2- = CaSO4 (2a) Additional sulfate may be lost from the brine by sulfate reduction: S042 + 1.33CH2 + 214- = H2S + 1.33CO2 + 1.33H20 (3a) The loss of carbonate species occurs by precipitation as carbonates: H2O + C02 + Cat = CaCO3 + 2H+ (4a) The net result of reactions 3 and 4 is: Ca 2+ + SO4 2- + 1.33CH2 = H2S + CaCO3 + 0.33H2O + 0.33CO2 (5a) The loss of potassium from brines is caused by the formation of potassium aluminosilicates: 2K+ + Al2Si2O5 (OH)4 + 4SiO2 = 2H + 2KAlSi2O8 + H2O (6a) The hydrogen ions produced by this reaction dissolve carbonates: 2H+ + CaCO3 = Ca 2+ + CO2 + H2O (7a) The net result of reactions 6 and 7 is: 2K+ + CaCO3 + Al2Si205 OH)4 + 4SiO2 = Ca2 + 2KA1Si3O8 + H2O + C02 (8a) A study of brines from central Mississippi has shown that the composition of these brines is related to the interaction of pore fluids from evaporites with minerals in the enclosing sedimentary rocks.

Jan 1, 1978

By Robert Y. Lamarche

INTRODUCTION Production of chrysotile asbestos from the northern Appalachians has been going on for 100 years and, on the basis of known reserves and the present rates of mining, appears assured of continued production for at least another 25 to 30 years. In spite of this, mining companies and government agencies are showing an increasing interest in exploring for chrysotile asbestos throughout this region and elsewhere in the world, implying that increases in the rate of consumption are envisioned. This chapter describes the geologic and tectonic settings surrounding these important chrysotile deposits, with emphasis on those in southern Quebec that yield about 90% of the total production from the northern Appala- chians. Detailed descriptions of a few individual deposits are also given, along with exploration guidelines aimed at facilitating the discovery of additional chrysotile deposits. One section of this chapter deals with the origin and mode of formation of the chrysotile deposits in the light of modern day concepts of plate tectonics. The objectives of this chapter are to give a brief description of the geologic and tectonic settings of the ultramafic rocks in which the numerous chrysotile deposits of the northern Appalachians are found; to describe a few of the individual deposits; to give a few exploration guidelines for those interested in exploring for new asbestos deposits in similar geologic environments; and to propose a new model for asbestos genesis in light of the recently developed theories of global tectonics. As this chapter is based almost entirely on field and laboratory observations, rather than on the study of experimental laboratory models, most of our deductions and suggestions are empirical in nature and may be interpreted in more than one way. The interpretations we have selected seem to offer, we feel, the best explanation of observed geological phenomena (Lamarche and Wicks, 1975). This region had a production capability in 1979 of close to p.5 Mt of chrysotile asbestos with 92% of this tonnage being derived from the deposits of the Eastern Townships of Quebec. With known resources, which now stand at between 36 and 40 Mt of fibers, this production capability seems assured for the next few decades. In spite of all known reserves of chrysotile asbestos, which now stand at between 36 and 40 Mt of fiber in this region alone, mining companies and government agencies are still showing a good deal of interest in exploring for new sources throughout the world. GEOLOGICAL SETTING The asbestos deposits at Baie Verte in eastern Newfoundland, Thetford Mines, Black Lake, Asbestos in southern Quebec, and Belvidere Mountain in Vermont, all occur in partly serpentinized ultramafic rocks that are part of the Lower Paleozoic ophiolite complexes of the northern Appalachians [Cady, Albee, Chidester, 1963, Chidester, Albee, Cady, 1978, Lamarche, 1972,1973, Laurent, 1973,1975, Williams, Hibbard, Bursnall, 1977, Norman and Strong, 1975). The deposits to the northeast of Thetford Mines, on the other hand, are found in a more highly serpentinized ultramafic body known as the Pennington dike, whose spatial, genetic, and chronological links with the ophiolite masses proper have not as yet been adequately resolved. The Appalachian ophiolites are part of an ultramafic belt (or belts), that extends from northwestern Newfoundland, through Quebec and Vermont. Fig. 1, and southwestward as far as the

Jan 1, 1986