Search Documents

By Keith A. Heasley

The LaModel program has been used successfully in the United States for many years to design pillars to ensure global stability of pillar recovery operations. However, the recent Crandall Canyon Mine collapse showed that further research was required to improve the design of pillar recovery under deep cover. Toward this end, a new calibration procedure was implemented in LaModel. This calibration procedure prescribes techniques for calibrating the critical LaModel input parameters based on empirical abutment loading and pillar strength, as utilized in the time-tested ALPS and ARMPS programs. The calibration procedure is intended to help guide a novice modeler in choosing calibrated input parameters that produce a standard model that fits within the verification database. However, the rigid parameter specification incorporated in the calibration procedure also removes most of the flexibility in LaModel for specific calibration to the unique conditions at a given mine site. In this paper, a number of the LaModel input parameters are varied outside the bounds of the suggested calibration and the effects on the model results are analyzed. Ultimately, it is shown how the LaModel user might vary certain input parameters to adjust the model to site-specific conditions, while still maintaining the general accuracy and philosophy of the recommended calibration.

Jan 1, 2012

By Arka Jyoti Das, Prabhat Kumar Mandal

"Coal mining in India has a strategic importance for the energy security of the country. Presently, the majority of coal production is coming from open-cast mining. Due to the fast depletion of reserves amenable to open-cast mining, future coal production will depend primarily on underground production. In conventional bard-and-pillar/room and pillar mining as it is practiced in India, the percentage of extraction is very low. In fact, within most Indian coalfields, a large number of coal seams extract only 15- 20% of coal, but no pillar extraction is done due to the presence of surface or sub-surface structures leading to huge amount of coal being locked-up in underground. Spontaneous heating and fire, the accumulation of poisonous gases, severe stability issues, unsafe workings and environmental hazards are all major problems associated with these developed coal pillars, so there is a pressing need for technology in the mining industry to extract this huge amount of coal locked up under different constraints. In this study, we propose that the locked-up coal be extracted by replacing the developed coal pillars with artificial pillars. The paper briefly discusses the extraction methodology designed for this and its evaluation through numerical modeling for applied suitability underground.INTRODUCTIONDriven by rising populations and urbanization, an expanding economy and also a quest for improved quality of life, energy usage in India is expected to increase manifold in the coming years. As for India's energy scenario and its projected future plans, there is no doubt that coal will remain a prime source of energy, even over the next few decades.The majority of coal production in India comes from open-cast mining because of large-scale mechanization, but the coal reserves amenable to open-cast mining are gradually depleting - which may impose adverse impacts on the energy sector if underground production does not increase. Underground coal extraction, meanwhile, is going to become more complicated in near future due to the fast exhaustion of easily mineable coal reserves."

Jan 1, 2016

By J. M. Krese

This paper gives an overview of the National REAP program emphasizing the program's current status and future plans. A brief historical review of the program will be given containing roof-fall accident trends and statistics. The latest developments in roof control technology and training as it affects the REAP program will be presented. A brief discussion concerning some effects of the implementation of the amendments to Part 75, CFR, concerning roof support is included.

Jan 1, 1988

By Rebecca Hardy

The escalating demand for coal, in addition to the steady depletion of reserves, has produced increasingly difficult mining conditions for coal mining companies within the United States, resulting in mining above or below previously mined areas. The safe and productive extraction of coal in a multiple seam environment requires specific design technology for effective mine planning. Presently, one of the most useful design approaches for multiple-seam feasibility analysis is using numerical modeling techniques. Therefore, numerical modeling programs LaModel 2.1 and Lam2D were used to determine the feasibility of mining the Herrin (No. 6) coal seam over an existing room-and-pillar mine in the Springfield (No. 5) coal seam in the Illinois Basin.

Jan 1, 2006

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By Qingxiang Huang

Shallow seam coal field has the largest coal reserve in China. Mining in shallow depth causes serious problems. One of them is subsurface dewatering. In this paper, the physical simulating model was performed to study overburden movement and aquiclude stability in the shallow seam mining of Yushuwan coal field, China. According to the characteristic of clay aquiclude in the overburden, the proper simulation materials and proportions of mixture for simulating the plastic clay aquiclude layers and brittle bedrock layers were determined by the stress-strain tests. The physical simulating model was carried out to simulate the failure and caving process of the roof and overburden. Based on the simulating tests, it was found that the movement of clay aquiclude follows the movement of the underlying bedrock layers. The basic caving mechanism of the overburden roof strata was also presented. The tests also showed that the best way to control the stability of aquiclude is to reduce the subsiding gradient Ts. This research provides a foundation for further study on mining dewatering and water conservation.

Jan 1, 2006

By Yi Luo

In dealing with various subsidence cases, accurate predictions of mining induced subsidence are the basis for correct assessment of subsidence influences and subsequent mitigation efforts. There is a good demand for a reliable tool to perform the subsidence predictions and related tasks. A comprehensive and integrated subsidence prediction model, CISPM, developed by the senior authors in the later 1980?s and early 1990?s (Peng and Luo, 1992) is one of such tools. Built on solid mathematical models and calibrated by a large number of collected subsidence cases, CISPM provides a rich set of features needed in subsidence engineering and research works. Its reliability and usefulness have been proven by numerous field applications. This upgrade of CISPM will not only preserve its original features and reliability but also provide some new needed features and a more user-friendly working environment.

Jan 1, 2008

By Jun Lu

There are many factors affecting the strength of pillar, including width-to-height (W/H) ratio, mechanical properties of coal and surrounding rocks, property of partings in the coal, and the interface property between coal seam and the roof/floor. In this paper, the effect of varying pillar?s width-to-height ratio (W/H=3, 5, 7, and 10) and coal/rock interface cohesion (Cj =50 psi, 150 psi, and 300 psi) on pillar strength has been studied. The confinement effect of W/H ratio and interface shear strength is investigated by studying their effects on the average minimum principal stress developed in the pillar. The deformation behavior of the coal pillar is investigated. It is found that the pillar?s transition from strain softening to strain hardening behavior depends on its W/H ratio and the interface shear strength.

Jan 1, 2008

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By Daniel Barkley

Underground coal mining in Illinois has a lengthy history dating back to the early 1800?s. High extraction underground mining has played a significant role in production through out this time. Modern mechanized longwall mining methods were introduced in the 1960?s and have been in continual use ever since. Regulations governing subsidence from underground coal extraction and the mitigation of resulting impacts to surface structures and surface land initiated in 1983. Despite the history of experience with subsidence, recent plans to longwall in Illinois have stirred public emotions and strong opposition. Anti and pro longwall groups formed and divided a community over the potential economic benefits new mining ventures could bring verses the potential problems associated with longwall mining in productive flat farmland. The debate culminated in a county wide referendum vote on the use of longwall mining. This paper provides an overview of the history of underground mining in Illinois, the controversy that has risen in central Illinois regarding longwall mining, and the efforts to educate the public about regulations that govern longwall subsidence.

Jan 1, 2007

By Daniel Su

Approximately 90% of the primary roof bolts used in CONSOL?s Pittsburgh seam coal mines is 2-piece, 8-foot long, 7/8? (or ¾?), high-strength, resin assisted, mechanical shell tensioned bolt. The remaining 10% is the 2-piece, 8-foot long, 7/8? combination bolt, which employs 4 feet of fast resin to anchor the deformed rebar at the top of the hole. In either system, a 1-3/8? hole is required to accommodate the mechanical shell and the coupler. The cheaper torque-tension rebar system, which is typically fully-grouted with 2-speed resin and which typically provides low bolt tension, is not used in CONSOL?s Pittsburgh seam mines. Rather, it is used in CONSOL?s Central Appalachia mines, where the roof rocks have CMRR rating of 50 or higher. Fully-grouted headed rebars, on the other hand, are used in CONSOL?s room-and-pillar mines. The selection of tensioned versus non-tensioned, fully-grouted bolts for coal mine primary roof support has been debated for the past thirty years. Many researches have been conducted to understand the theoretical bases behind the two systems. This paper describes CONSOL?s experience of using a new fully-grouted, mechanical shell tensioned bolt in the Pittsburgh seam with the development of low insertion force resin.

Jan 1, 2007

By Marc Arl

Failures of the face and roof above longwall shields have caused days and sometimes weeks of lost production. A common recovery method for these failures has been to pump light weight cementitious grout into the roof and face cavity to stabilize the area This approach while effective is very time consuming and costly. Mines in several coal producing nations have over the past few years been applying phenolic foam grouts in these situations in lieu of cementitious materials. Phenolic foam is a two-component injection product intended for cavity filling, air and gas sealing and the consolidation of highly fractured strata. The properties of phenolic foam; rapid application, quick setting, high expansion rate, high compressive strength and excellent anti-static properties, produce a fast, safe and cost effective cavity filing solution. The product is also classified as fire resistant and so is also suitable for sealing off underground heatings and for aiding fire fighting operations in deep mines. This paper will discuss the application and use of phenolic foam in various underground coal mines in the world over the past few years.

Jan 1, 2005

By Sandin E. Phillipson

The Mine Safety and Health Administration?s Roof Control Division responded to a massive ground failure at an underground marble mine in northern Georgia. The ground failure occurred in a benched area that had been abandoned in the early 1990s. It involved the failure of an estimated 19 pillars, in conjunction with a massive roof fall of an undetermined extent that was at least 60 ft high. Pillars in the benched area had been mined nominally 40 x 40 feet to a height of 50 feet ft, with 40-ft mining widths, although it seems likely from measurements and accounts from mining personnel that pillars were even smaller than intended. Average overburden depth was 500 ft, and the rock mass was characterized by three sets of intersecting geological discontinuities that not only defined very blocky conditions that were conducive to pillar spalling and volume loss, but they were also adversely oriented in such a way as to cut diagonally through pillars at a high angle. The recently released S-Pillar software from NIOSH was used to determine pillar safety factors in the failure area and indicated that pillars were undersized for the conditions. S-Pillar was used to assess pillar stability in active areas to evaluate the likelihood of experiencing similar collapses in the future. S-Pillar correctly identified the pillars in the bench area as having been at risk for instability, in light of their ultimate failure. A two-dimensional finite element model was used to evaluate the possible stages of failure and to assess the likelihood of continued failure in the benched area that might affect more distal mine openings. Although stone mines are generally characterized as having more forgiving conditions than those found in softer sedimentary rocks, the failure shares some characteristics with domino-style massive pillar collapses experienced in coal and trona mines. First, the minimum dimension of the benched area approached 350 ft; second, the pillars defined by benching had small width-to-height ratios (0.8), and; third, the pillar failure area was slightly greater than 4 acres. The massive pillar collapse and associated roof fall illustrate the importance of incorporating pillars that have been properly sized for depth and for the final bench height. Furthermore, the designed dimensions must be adhered to during the actual mining process. Finally, the importance of understanding the geological conditions and their effect on the rock mass is critical.

Jan 1, 2012

By Daniel W. Su

This paper presents the results of a detailed geotechnical study on the potential multiple seam interaction between the No. 2 Gas (upper) and the Powellton seams, which are separated by an average interburden of 45 ft. The interburden consists of 4 ft of clay shale below the No. 2 Gas seam, 38 ft of massive sandstone, and 3 ft of shale above the Powellton seam. The No. 2 Gas seam was mined about 60 years ago, and many water-pooled areas were projected to be present. The deepest overburden over the No. 2 Gas seam is about 750 ft. To evaluate the potential interaction between the two mine works and to determine the pillar safety factor, Analysis of Multiple Seam Stability (AMSS) software was initially used to determine pillar dimensions to obtain a minimum safety factor of 2.0 for areas under pooled water, as well as a minimum safety factor of 1.5 for areas not under pooled water. Furthermore, to assess the quality of the interburden rock strata, two surface core holes were drilled, and rock cores were tested in the laboratory for their strength and elastic moduli. Using the experimentally determined strengths and moduli as part of the input parameters, the RocScience Phase2 finite element program was employed to model the stress field scenarios and estimate the safety factors of the interburden rock strata before and after Powellton seam mining. The pillar safety factors derived from the Phase2 analysis were in excellent agreement with those obtained from the AMSS analysis. Phase2 results also predicted that the effect of the Powellton seam mining, first mining only, would reach a maximum of 19 ft above the Powellton seam, which led to the proposal of drilling 25-ft deep test holes to detect water, instead of the 45-ft deep test holes mandated by MSHA. The proposed test-hole height was accepted by both Mine Safety and Health Administration (MSHA) District 4 and the state of West Virginia. Mining of the Powellton coal seam commenced in February 2011 and continued for eight months. To date, no 25-ft deep hole has encountered water under the water-pooled zone, which validates the RocScience Phase2 finite element analysis. Also, inmine observation of excellent pillar stability and roof condition confirms the validity of the AMSS analysis.

Jan 1, 2012

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987

By Anthony (Sam) J. S. Spearing

Backfilling using coal waste is not a novel means for waste disposal throughout the world; yet, backfilling using a high density (paste) backfill is relatively new, except in Germany and Poland. One of the main benefits of a high density backfill, as opposed to a low density (slurry) backfill, is that, if placed at a low permeability and low moisture content, the risk of water table contamination can be relatively low. In addition, if paste backfill can be placed cost effectively, environmental benefits are huge because the surface impoundment footprint can be greatly reduced or even eliminated. This is especially true in room-and-pillar applications. In its current state, backfilling is considerably more costly than surface disposal. This is mainly because paste, as opposed to slurry, significantly increases backfill placement costs; however, this could be offset by increasing the achievable extraction rate. Overall, such a system could potentially improve the public?s image of coal mining in the US for a myriad of reasons. This paper discusses a proposed backfill system for a typical room-and-pillar coal mine in the Illinois Basin of the US and clearly shows the technical advantages, although costs are still higher with fill. The cost differential will likely reduce over time, in favor of the backfill option, as costs of traditional surface disposal increase, due mainly to ever-restrictive disposal regulations.

Jan 1, 2013

By Dr. Daniel W. H. Su

t is both an honor and privilege for me to nominate Dr. Daniel W. H. Su for the inaugural Syd S. Peng Ground Control in Mining Award. I can think of no better candidate than Daniel that is deserving of this award ? an award to recognize technical excellence in advancing ground control technologies [and] approaches. Daniel?s education and career spans over three decades. Having graduated from National Cheng Kung University in Taiwan in 1972 with a B.S. degree in Mining and Petroleum Engineering, he spent the next four years in the Taiwanese military and mining industry, before moving to the United States, where he enrolled in West Virginia University?s Mining Engineering Department. He received his M.S degree in Mining Engineering from WVU in 1978; then in 1982 became the first person to ever receive a Ph.D. in Mining from WVU. His thesis was titled, ?Development of Ultrasonic Techniques for the Measurement of In Situ Stresses?.

Jan 1, 2006

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Zbigniew Lubosik, Stanislaw Prusek

"The main elements of hard coal extraction systems in the Polish mining industry, including the characteristics of gateroads, are described, followed by several dozen underground measurements of gateroad roof sag performed in different geological and mining conditions in Upper Silesia Coal Basin.Based on the analysis of the roof sag measurements, an attempt to describe the gateroad roof sag process using a geometrical model was made. To build the model, it was assumed that the roof sag curve could be described by three straight lines. The first line describes the roof sag ahead of the longwall face; the second line, the sag at the longwall-gateroad junction zone; and the last line describes the zone behind the longwall face. Determining the intersection points and inclination angles is essential for the model. These model parameters depend on the geological and mining conditions in the gateroad.Using the statistical computations and analysis, the dependencies between the characteristic points of the gateroad roof sag model and the selected geological and mining parameters were defined. The STATISTICA computer program by StatSoft was used for computation.This paper presents a simple form of the geometrical description of roadway roof sag progression that is very useful during the gateroad support design process.INTRODUCTIONThe longwall system with caving is the dominant method in European mining in cases of hard coal seam extraction. For instance, in Poland, in 2009, 117 longwalls were driven, with total production of 77.5 million tonnes. In roughly 95% of the longwalls, mining operations were conducted using longwalls with roof caving; the remaining 5% used the hydraulic stowing system. The average mining depth was about 700 m (2,297 ft), and average daily output per face was approximately 2,600 tonnes per day. When using the longwall mining system, gateroads play an important role. These principal roadways transport materials, mine crews, and output. In addition, they impact ventilation of the extraction area, affecting, among other things, the climatic conditions or methane hazard. Unfortunately, difficulties often appear in maintaining an adequate size for the gateroads, due to the face line, which causes origination zones with stress concentration around the gateroad, resulting in rock mass movements in the form ofroofsag, floor heave, or horizontal convergence (Figure 1)."

Jan 1, 2010

By Russell C. Frith

This paper examines the design of longwall shields, focusing on those aspects that are critical to either their successful application or contribution to failure during longwall extraction. In many instances, longwall shields are assessed and designed along lines similar to that of roadway ground support systems, namely according to typical or normal geotechnical conditions. However it will be contended that for longwall shields, this is inappropriate because unlike roadway ground support systems, longwall shields cannot be supplemented with additional or secondary support in localised areas of adverse geotechnical conditions. In other words, the longwall shield needs to be designed according to what are judged to be worst case or adverse geotechnical conditions?the outcome being that a well-designed shield will be significantly over-rated for the majority of its working life. Therefore, it will be argued that the additional capital cost of such shield design can be readily justified as a prudent riskbased outcome that is essential to minimising future business risks due to strata instability on the longwall face. Shield geometry will be discussed, including such relevant factors as leg angle, inclination of the top caving shield, canopy ratio, operating height range, and tip to face distance. These are all well-established longwall shield design considerations and, most importantly, areas whereby inadequate design can render a longwall shield as highly ineffective. The issue of tip to face distance will be considered in detail, in particular, the extent by which it is an important geotechnical design consideration, the conclusion being reached that, in fact, it is not. The critical importance of maximising set to yield ratio within practical operating limits will be justified, the wisdom of this having been subject to questioning in more recent technical literature. Overall, the aim is to provide the industry with a set of suggested guidelines for future use when designing longwall shields and, hopefully, to initiate discussion on a subject that, unlike roadway ground support design, is not well covered in its entirety in the published technical literature.

Jan 1, 2013