Search Documents

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By James C. Barker

Recent investigations of a 55-km long trend of intrusive complexes on southern Prince of Wales Island have identified significant resources of Nb, Y, REE. U, Zr, and a host of potential by-product metals. The northwesterly trend comprises multi-phased sodic alkaline and peralkaline diorite, monzonite, syenite, and riebeckite granite. There are at least three significant deposit types recognized, two of which, 1) pegmatite dikes/vein-dikes that zone laterally from the intrusions and 2) concentrically zoned pegmatites, contain most of the lithophile metals. A third, epigenetic replacement-type mineralization, contains much of the U resource. Other deposit types with minor or unknown resource potential include diatremes, carbonatite, and placers. This report summarizes the deposit evaluations, characterizes the mineralization, and estimates the resources. To date a total of 40.7 million tons of mineralized material is estimated as indicated or inferred. Most of the Y203 plus REO is at a grade exceeding 0.5% and half of the Nb20S exceeds 0.125%. Tonnage estimates would likely be substantially lncreased with additional exploration. Mineralogy is generally fine-grained and complex, and consists of more than a dozen principal REE-Y-Nb-U-Th-Zr phases, the sum of which may compose up to half of the rock. Approximately half of the REE-Y content comprises the heavy yttrium subgroup which is uncommon compared to deposits elsewhere. Although the Alaskan deposits are likely subeconomic at today's metal prices and consumption levels. recent technological advances suggest future demand may increase.

Jan 1, 1988

By M. Jortikka

The smelting process of the old reverberatory furnace including its capacity has been improved over the years in different ways eg. with oxy-fuel burners, parallel reactors with the reverb or with various modifications of the reverb furnace itself. The future reverb modifications with old concepts are difficult or impossible as the increased copper losses in slag call for separate slag treatment and particularly the process modifications do not solve the environmental issues but instead mean unavoidable high capital and operating costs in gas cleaning and sulphur recovery. During the last decades improvement in process performance and increase in capacity of copper flash smelters has been achieved easily by substituting the pre-heated process air by highly oxygen enriched air. The flash furnaces of today, however, are inherently designed to operate with high oxygen enrichment. Further process improvement with a view to production costs and capacity increase as well as to the more stringent environmental requirements is possible with even higher oxygen enrichment. This, apart from the advantages it generates, requires improvements in and careful design of the feed system, concentrate burner, furnace cooling and the off-gas line as well as adaption of the flash converting instead of the conventional Peirce-Smith converters. A logical answer even for the revamping of the reverb smelters in the future is the total replacement of the reverb furnaces with flash smelting together with flash converting. This paper discusses the possibilities for future process improvements of the existing flash smelters taking into account the process concepts, equipment modifications and capital aspects not forgetting the environmental issues. The revamping of the PASAR smelter in Philippines is introduced as an example of a recent success story.

Jan 1, 1994

By Jewel Gomes

Produced water (PW) is salty water trapped in the reservoir rock and brought up along with oil or gas during production. It subsists under high pressures and temperatures, and usually contains hydrocarbons and metals. Therefore, it must be treated before being discharged to surface water. Different techniques are being used to treat PW through phase separations, system control and design, and chemical treatments. In this paper, we discuss our experimental results on treating PW through electrocoagulation (EC). The performance of EC was investigated for the reduction of chemical oxygen demand (COD) and metal ions. Effects of different electrodes, residence time, current density, and pH were also studied to optimize the treatment conditions. Different kinds of cleansing agents, such as lime and borax were used to break the buffering effect encountered during treatment. FTIR, SEM/EDS, and XRD were used to characterize the EC-floc and thus to elucidate removal mechanisms.

Jan 1, 2009

By G. Coryell, E. Brack

"Remaining competitive in today's metal markets requires that copper smelters utilize the latest technology offered in process control, data acquisition, and process optimization. State-of-the-art tools like minicomputers, personal computers, and microprocessor based controllers provide real time process information that assist in making proper adjustments to the overall control strategy of an operating plant. The database accumulated by such systems broaden process knowledge, thereby reducing costly errors and plant downtime.IntroductionThe ASARCO Hayden Plant is located approximately 80 miles southeast of Phoenix, Arizona. The plant was commissioned in 1912 for the purpose of smelting copper concentrates from the surrounding mining district. Copper was produced for many years using calcining, reverberatory smelting and copper converting techniques. With the stricter environmental controls of the 1970's, the smelter experienced substantial declines in efficiency and productivity. It became necessary to identify and install a new smelting technology to maintain the viability of the Hayden plant.In 1980, after evaluating several smelting techniques, ASARCO management selected flash smelting as developed by International Nickel Company (INCO). One hundred and thirty-two million dollars was allocated for the project and construction began in 1982. Construction was completed and the new plant came on line in November of 1983."

Jan 1, 1989

By Francis Vanbellen

In Union Minière's Hoboken smelter and refinery for complex non-ferrous materials, the treatment of recycling products, containing precious metals, occupies a dominant place. For all feed materials, the first step, prior to their treatment, is to classify them in order toselect an accurate and economical procedure for sampling as well as to dispatch them to the optimal process scheme. More than 150 different procedures for sampling are commonly used. The most important ones are briefly discussed in the paper. Precious metals bearing recycling materials vary widely with respect to their physical aspect, their chemical composition and the value of their precious metal content. All these parameters are taken into consideration to select the most appropriate process among the multiple possibilities of Union Minière's flexible integrated flow-sheet. Different stages of the operations as well as the main flow-sheets are described.

Jan 1, 1995

By John A. Herbst

Plantwide control of mineral processing operations has long been sought for its potential benefits. These benefits include minute-to-minute optimization, reacting to disturbances in ore characteristics and equipment status as they happen and the coordination of all unit operations in pursuit of the highest performance level. However several difficult challenges have kept us from fully realizing those benefits. One of these challenges has been to provide fairly complete quantitative descriptions of Unit operations to account for critical interactions within and 'between unit operations. In some cases we understand the physics and chemistry very well and can incorporate that 'knowledge into phenomenological models. In other cases our knowledge is incomplete, so we must rely on other forms of knowledge such as fuzzy logic or neural nets. Another challenge to be met has been to simultaneously compute a large number of manipulated variables. In the past this challenge was met by optimizing only unit-by-unit, rather than on a global basis to significantly reduce the number of variables. In this paper, a procedure that globally optimizes one or two important variables is outlined. This procedure comes much closer to true plantwide optimizing control while remaining computationally feasible. Finally, another major challenge is to choose a meaningful global objective that can be calculated With the models and can be effectively optimized. Financial goals seems to be the objectives of choice. This paper discusses recent progress In overcoming the challenges and illustrates a promising approach which is being pursued at :Mexicana de Cobre's 'La Caridad copper ore concentrator. At M de C, advanced ,control strategies have been 'installed one at a time in the crushing, grinding and flotation sections. During this period, the throughput of La Caridad, Mexico's largest copper concentrator, 'increased from 76;000 tpd to 90,000 tpd. Plantwide integration is expected' to gain an additional 3% improvement in profitability.

Jan 1, 1996

By G. G. Krishna Murthy

Interactions of wustite and hematite pellets with Fe-C melts were investigated experimentally by examining the effect of pellet size and bath temperature on the reduction rates of the pellets. Experiments were carried out in the temperature range 1473-1923 K. A flash X-ray equipment was used to obtain images of the melt surface during its reaction with an oxide pellet. The reduction rates were calculated using experimentally estimated time for complete reaction of a pellet, tR. The value of tR was determined employing gas mass flow rate, or pressure rise in the sealed furnace, versus time traces. The value of tR was the same for both wustite and hematite pellets of equal weight at or above 1723 K and it decreased with increasing melt temperature. But the reduction rate was substantially lower at temperatures below 1651 K, the melting point of wustite. The rates were defined as the rate of moles of oxygen removed from the pellet per unit area of bath free surface and it was found that the bath surface area affects the reduction rates. It was established that the overall reaction followed nth-order rate kinetics with the values of n falling between 0.3 and 0.4 for temperatures above the melting point of wustite. The apparent activation energy determined using the apparent rate constants obtained from the experimental data was 76.2 + 27.7 kJ/mol-O.

Jan 1, 1992

By Dhanesh Chandra

Metal carbonyls are of great importance in chemical vapor deposition (CVD), composite materials fabrication, and other near-net shape technologies. Carbonyl CVD application applies to deposition of high-purity metallic/alloy coatings. Vapor pressures of solid Os3(CO)12,Rh6(CO)16, Ru3(CO)12, Ir4(CO)12, Re2(CO)10, Co2(CO)8, Cr(CO)12,, and W(CO)6carbonyls have been measured using gravimetric-torsion effusion system. The vapor pressure data is used for many low and high temperature CVD applications. Interesting decomposition/disproportionation vaporization behavior has been notedfor Rh6(CO)16, Ru3(CO)12 and Co2(CO)8. The vaporization studies of Rh6(CO)16 showed virtually complete decomposition to Rh metal and the measured molecular weight of the effusing gas from the solid Rh6(CO)16 was 27.75 g/mol, close to that of carbon monoxide as compared to 1065.56 g/mol for the value of solid Rh6(CO)16. Electron microscopic characterization, X-ray line broadening results for Rh carbonyl has been performed on the vaporization product. However, Ru3(CO)12, Co2(CO)8 showed very complex behavior. The molecular weights of the vaporizing species have been estimated and the numbers of vaporizing species are proposed. For example, there was partial decomposition of Ru3(CO)12to(approx. 52%) metallic Ru and CO gas during vaporization, as suggested by the difference in the molecular weight of the vaporizing species of 107.58 g/mol compared to the actual value of 639.33 g/mol. The dimer Co2(CO)8 partially disproportionates to tetramer Co4(CO)12, monomer Co(CO)4, and CO gas. Whereas, the Os3(CO)12, Cr(CO)12,, and W(CO)6have shown virtually no disproportionation. The total vapor pressures of all the above-motioned carbonyls, partial pressures of various species, average molecular weights of the effusing gases, equilibrium constants for the vaporization reactions, their enthalpies, entropies, and Gibbs energies will be presented.

Jan 1, 2006

By W. D. Keller

Scanning electron microscopy (SEM) accompanied by X-ray energy dispersive analysis (XES) is a useful tool in process clay mineralogy. The texture of kaolin, illustrated by SEM, gives a clue to its mode of genesis and probable industrial application. One type of kaolin, originating dominantly by weathering, has an open texture, slakes readily, and is used for filling and coating paper. Another type, in contrast, originates by diagenesis of Al-silicate sediments, and spectacularly resists slaking, thereby enabling it to maintain its bulk density and controlled size and shape of particles after crushing and moistening; this meets an important requirement for the manufacture of refractories. Ratios of elemental Al:Si that may be rapidly determined by SEM and XES yield information on the origin and purity of bauxite and bauxitic clays, and aid in quality control and processing of them. SEM of dissimilar textures of quartz, as in chert and novaculite, are evidence for geothermometry on a stratigraphic scale that is potentially useful in delimiting thermally favorable or unfavorable areas for hydrocarbon exploration, and possibly for unexposed metallic ore deposits.

Jan 1, 1982

By O. Barbosa F.

The thermochemistry of the systems SCN-H2O, Au-SCN-H2O and Ag-SCN-H2O is discussed. Potential-pH diagrams at 25°C are drawn for each system considering several sets of concentrations of the species involved. The information provided by the potential-pH diagrams is.complemented by distribution curves for each series of gold and silver complexes with thiocyanate. The analysis includes comparisons between the thiocyanate systems and the analogous cyanide systems, pointing out analogies and differences between the leaching of gold and silver with thiocyanate and with cyanide. The possibility of using soluble oxidizing agents such as ferric ions, hydrogen peroxide and Caro's acid is evaluated. The thermodynamic data used in the calculations and the chemical reactions represented in the Pourbaix diagrams are all reported in three Appendices. The overall results indicate the thermodynamic conditions for gold and silver leaching by thiocyanate.

Jan 1, 1989

By W. D. Riley

Engineered Scavenger Compounds (ESCs), developed by the U. S. Bureau of Mines I are a novel class of compounds that can selectively recover a desired element from 'a solid or molten alloy. Lithium titanate (Li2Tip7 or Li20' 3TiO.) is being used as an ESC to recover lithium (Li) from Aluminum-Lithium (AI-Li) alloys. X-ray diffraction measurements have shown that lithium titanate undergoes a phase change from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of Li in the matrix of the material and the effect of temperature. Although both of the structures are metastable, the hexagonal phase that forms during the scavenging of Li from AI-Li alloys appears to be the more stable phase. Recovering Li from the ESC by electtodeposition does not cause the structure to revert to the orthorhombic phase. Both the orthorhombic and the hexagonal structures of Li.Til07 have similar scavenging capacities for Li. This paper proposes a new mechanism for the phase transformation.

Jan 1, 1991

By C. O. Bounds

The magnetic properties of (NdDy)15Fe78B6 sintered magnets have been evaluated using powder prepared by Inert gas atomization. The atomized powder had a particle size distribution from 1 to approximate 1000 microns. The as atomized powders have been sieved into, coarse, intermediate, and fine fractions; magnetic properties were evaluated for the as produced powder and each fraction. A B, of 11.7 kG, a Hci of 11.0 kOe and a BHmax of 32.5 MGOe was -obtained on a sintered magnet made from the as-atomized powder. The magnet made from coarse powder exhibited a slightly higher B, of 12.1 kG, while that from fine powder showed a decrease in B, to 11.2 kG. Hydrogen decrepitation has been utilized to study its effect on the magnetic properties. Finally, cast ingots with a definite columnar structure have also been used to compare the magnetic properties of magnets of the same nominal, composition but of different alloy preparation process. Hydrogen decrepitation does not appear to improve the magnetic properties of magnets made from thin cast ingots. However, it does show a significant improvement in the Hci of magnets made from the atomized powders. Possible causes for the differences in the magnetic properties on magnets made from each process have been discussed in the paper.

Jan 1, 1992

By John L. Watson

The dewatering of steel industry waste sludges prior to discard or recycling often presents significant problems due to the fineness of the sludge particles, which may blind the filter medium and/or produce a cake with limited porosity, Several steel plant wastes, such as sludges from BOF and EAF gas cleaning operations exhibit not only a very fine particle size, but also some degree of magnetic character, A novel process has been developed to utilize the magnetic character of such sludges to enhance dewatering through a multi-force operation involving magnetic, chemical and vacuum forces, The process consists essentially of undertaking vacuum filtration of a flocculated sludge in a magnetic field, This is achieved by installing a permanent magnetic in a fixed position on the axis of a vacuum drum filter, thus effecting filtration of magnetic and non- magnetic particles, bound together in flocs, in a magnetic field, Previous tests using a modified laboratory vacuum drum filter treating artificial (magnetite) and industry waste (BF sludge) feeds have demonstrated that filtration capacity may be enhanced significantly with increases of up to 3000/0, An explanation of the mechanisms associated with the enhanced filtration was not obvious, and this research was undertaken to permit the cake formation in the magnetic field to be monitored to provide an insight into the manner in which particles agglomerate to form the cake. These tests revealed that the magnetic field caused magnetic particles to be aligned perpendicular to the filter surface and to form channels through which filtrate could freely pass thus increasing capacity, The effects of various magnetic fields and field strengths on the filtration process were also investigated. A simple computer model was constructed to demonstrate the proposed theory of multi-force dewatering, The model output graphically illustrated the suggested mechanism and confirmed the enhanced capacity of the novel dewatering process,

Jan 1, 1996

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006

By Jose Antonio Silva Souza, Emanuel Negrao Macedo, Iara Ferreira Santos, Otacilio Dias, Luis C. A. Venancio

"The Bayer process alumina production generates 0.7 to 2.0 ton of bauxite residue (BR) and an average of 1.0 ton of C02 per ton of alumina produced. The direct reaction of exhaust gases to reduce the alkalinity of the BR may allow a triple gain: improve the storage conditions, open a range of new applications for BR and sequester from 16 to 102 kg of C02 per ton of alumina. This paper shows the measurement of C02 captured during a pilot scale reaction of a suspension of BR in water with flue gas, produced from direct oil burning. Three different types of reactors were used: one spray tower and two packed columns. The inlet and exhaust gases were analyzed using electrochemical and non dispersive infrared sensors. The pH of the suspension was monitored during and after the reaction to evaluate the buffer effect.IntroductionAlumina is mainly produced from refining bauxite using the Bayer process. This process consists of extracting the aluminum oxide through its dissolution in caustic soda and the separation of insoluble residues. The remaining bauxite residue (BR) although not particularly toxic, poses risks to the environment due to the large volume and its reactivity. According to the latest technology it is stacked on sealed deposits specially constructed. To date the vast majority of the bauxite residue that has been produced was stored and were not incorporated into any existing production processes to significant amount with exception to some extent of the sintering process residue at Russia and China [l]. On the other hand, a strategic goal was set in 2010 by the Bauxite and Alumina Committee of the International Aluminium Institute (formed by the majority of the industries) to reuse 20% of BR in 2025 [2]. China has established the same objective for 2015[1].This paper is a sequel of two others presented at TMS 2010/2012 [3-4] and describes:• A pilot plant assembled for testing the carbonation process of BR with gaseous effluents similar of the refining process.• The methodology used to measure the amount of C02 captured during the carbonation process.• The results of the carbonation process, the C02 capture and the buffering effect of the pH.This process is studied in order to consume minimal power and use the effluent as efficiently as possible in different reactors from low cost to ultra high performance. The process is designed for minimizing the power consumption and equipment investment."

Jan 1, 2013

By Xu Zhong

The theoretical limit to smelting rate and possibly the size of a smelter is dependent on the rate of heat transfer, and the chemical kinetics of both sulfur removal and minor element volatilization. The fundamental kinetics of volatilization of minor elements such as As, Sb, Bi, and Pb from matte and white metal is being investigated. It has been shown that the molecular form of trace elements in matte depends on the chemical potential of sulfur and the propensity for the minor element to form a sulfide. The impact of the variable molecular form of the minor elements on the volatilization kinetics is unknown and is under investigation in this study. The experimental technique is reviewed and preliminary results are reported in this manuscript.

Jan 1, 1995

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By Jiann-Yang Hwang

The economic growth in new developing countries such as China and India has stimulated strong demands in basic materials such as steel. World steel production has exceeded the milestone of a billion tons a year recently. However, the blast furnace technology, which was invented in 1340 A.D., is still the fundamental route for today?s steel production. It is important to develop a new generation of steelmaking technology that can meet the society?s needs from the energy, environmental and economic standpoints in the 21st century. The new microwave and electric arc heating technology discussed in this paper provides a totally different mass and heat transfer mechanism from the conventional blast furnace technology and offers a great potential to meet our society?s needs.

Jan 1, 2006

By P. Heald-Wetlaufer

Doubly polished sections (i.e., sections polished on both sides) allow insights into complex paragenetic relationships, the interpretation of which is essential to understanding ore-forming processes. Alternate viewing of these optically superior sections in transmitted and. reflected light facilitates the recognition and definition of growth zones in ore and gangue minerals and the interpretation of postdepositional changes, such as hydrothermal leaching and replacement. Many such observations would escape detection by conventional petrographic methods. Our procedure for preparing doubly polished sections has evolved during the past 20 years and incorporates many standard procedures. Studies from such diverse districts as Creede, Colorado, Hokuroku, Japan, and the Upper Mississippi Valley zinc-lead district, southwestern Wisconsin, demonstrate the value of observations from doubly polished sections in constructing genetic models. The advent of doubly polished sections represents a major advance in the study of ore deposits and they should be a standard tool in every ore petrology laboratory.

Jan 1, 1982