Search Documents

By C. M. Antony

The galvanizing process involves the use of accessory equipment in a series of aggressive environments including zinc ammonium chloride flux, molten zinc at 45S°C (850°F), and acid for stripping of adherent zinc. An Fe-Ni-Cr-Co alloy has been identified which combines excellent strength and resistance to molten zinc and acid attack making it suitable for accessory equipment. The alloy was field tested by a commercial galvanizer as basket material and was found to provide improved life compared to original low-alloy steel baskets while cross-section thickness was reduced 44%. Additionally, other associated processing cost savings were realized.

Jan 1, 1992

"Mineral flotation processes are often characterized by long dead times and slow process dynamics. The process dynamics change due to different ore types, feed grades and circulating loads. These are some of the factors that can make control of flotation processes difficult. Implementation of adaptive control algorithms at Brunswick Mining has made controlling these processes feasible. The role of adaptive controllers in plant optimization and the overall control philosophy is discussed.IntroductionBrunswick Mining is located just outside of Bathurst, New Brunswick, Canada. The concentrator processes approximately 10,250 tonnes per day of ore that assays at approximately 8.9 %Zn, 3.6 %Pb, 0.3 %Cu and 100 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 36 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb.The original flotation process control system, supplied by Outokompu Oy of Finland, was replaced in the summer of 1988 by a Provox system supplied by Fisher Controls Inc. The Provox system consists of two redundant integrated function controllers (IFC's), two operator console stations with two screens each and a Digital Equipment Co. microVax II computer running Fisher's Computer Highway Interface Package (CHIP).In January 1989 a boiler management package, which includes the boiler control hardware and another operator's console, will be added to the Provox system. In late spring of 1989, a Vax 3200 computer running G2 artificial intelligence software from Gensym Corporation will be installed. These devices are all connected using a redundant data highway that runs around the plant.The primary measurement devices in the flotation circuit are two Courier on-stream X-ray analyzers. The Courier systems each have 14 sample cells with two streams multiplexed into each cell. Each pass of the on-stream head takes approximately 6 minutes yielding a nominal sampling interval of 12 minutes. The Courier passes its assays to its respective IFC. The IFC handles the digital and analog I/O, DDC and cascade loop control, some low level calculations and sequencing. The CHIP microVax has 9MB of memory and 220MB of mass storage running under the VMS operating system. The CHIP microVax is a central database for the Provox system. It is used for data trending, metallurgical modelling and balancing, instrumentation database, long term storage, and on-line adaptive assay control."

Jan 1, 1989

By Richard D. Hagni

The United States is dependent upon foreign sources for more than 93% of its bauxite and alumina supply. Domestic production of bauxite, which comes from Alabama, Georgia and Arkansas, is limited to those bauxite ores containing less than about l ½ % iron. Bauxites with higher iron contents are generally not utilized because they cause problems in bauxite calcining and especially because they produce undesirable brick discoloration and cracking. In order to improve beneficiation and expand the utilization of high-iron or ferruginous bauxites, a mineralogical and textural study has been conducted on selected samples from the Eufaula, Alabama, bauxite district. Reflected light microscopic, petrographic, and X-ray techniques have shown that a variety of iron minerals are present, including hematite, goethite, lepidocrosite, siderite, pyrite, marcasite, and ilmenite. Although the iron minerals may be locally concentrated into concretions and pisolites, most occur as very fine grains that are disseminated and show a variety of intergrowths. Mineralogical and textural observations indicate that the fine-grained iron mineral grains may be amenable to high gradient magnetic separation.

Jan 1, 1981

By E. Daniel Baker

"The term ""oxide disseminated gold deposits"" refers to near surface, gold-bearing veins, faults, and shear zones that typically contain appreciable amounts of oxidized ore or gossanous material, resulting from oxidation of sulphides.The concept of oxide gold deposits underwent a dramatic change after the discovery of the Carlin gold mine in north-central Nevada in the early 1960's. Now the term implies large tonnage, low-grade bulk minable deposits that are processed by milling and/or heap leach methods.Oxide gold deposits may now be classified into two types: (1) primacy ores derived directly from the effects of hydrothermal alteration on host rocks, and (2) secondary oxide ores derived from the supergene oxidizing effects of circulating post-mineral meteoric waters on gold-bearing sulphides. Each type of deposit has unique diagnostic mineralogic and metallurgical characteristics that must be addressed to achieve successful exploration strategies and viable metallurgical exploitation.The author would like to thank the management of Newmont Metallurgical Services and Newmont Mining Company for allowing presentation of this paper. Thanks are due Sevkett Acar, Donald M. Hausen, Jerry R. Odekirk, and D. Erik Spiller for their critical review of the manuscript. Also, thanks are extended to all those cited and uncited whose hard work and dedication have led to the discovery and exploitation of near-surface oxide gold deposits. Our knowledge would be greatly limited without the dedication and research of many others."

Jan 1, 1997

By Yuzhe Zhang, Xiaodi Huang, Xinli Wang, Bowen Li, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

The recycling of waste tires has been a big environmental problem. About 280 million waste tires are produced annually in the United States and more than 2 billion tires are stockpiled, which cause fire hazards and health issues. Tire rubbers are insoluble elastic high polymer materials. They are not biodegradable and may take hundreds of years to decompose in the natural environment. Microwave irradiation can be a thermal processing method for the decomposition of tire rubbers. In this study, the microwave absorption properties of waste tire at various temperatures are characterized to determine the conditions favorable for the microwave heating of waste tires.

Jan 1, 2015

By Ana Bohé

Nowadays, Gas-solid processes are widely used in the industry. The chloration and carbochlorination of metallic compounds are some of this kind of non catalitic heterogeneous reactions. In particular those related with extractive metallurgy of refractory elements (Zr, Ti, Nb, Ta, RE, etc). The development of materials to be used in reactors at elevated temperatures and with high corrosion performance, enhance the application of this kind of processes. Although they are currently carried out in the production of many comodities, the mechanism of most of them are yet not well understood. The present work is a deep discussion on the most important aspects to take into account for determining the mechanism of gas- solid reaction, and those criteria fulfil in this analysis were applied to chlorination and carbochlorination examples. The microstructural characteristic of solids, the mass and heat transfer phenomenon, the adsorption and desorption of gaseous species on active surface, surface diffusion processes and chemical elementary steps, which are the mainly contributions to the mechanism of these reactions were analysed. Furthermore, the effect of them on the reactivity of solids and the control step of the reactions were determined. The application of catalitic mathematical models to this kind of reaction and the modification for the better interpretation of experimental results is also undertaken. The most appropriate experimental procedures for following these reactions and the microstructural characterization techniques needed to be use in each case, there limits and applicability are also indicated.

Jan 1, 2006

"Recycling of solid wastes plays an important role in environmental protection. However, solid wastes are often contaminated with some undesired components so that many of these solid wastes are hardly economically recycled. Therefore, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes. There exist three general strategies of separation of undesired components from solid wastes: before-process separation, post-process separation and in-process separation. In this paper, different separation strategies are discussed in terms of energy requirement and availability, implementation complexity and additional need for environmental protection. It is concluded that of all separation strategies, in-process separation has the least energy requirement, the least implementation complexity and the minimum need for additional environmental protection.IntroductionIn industries, solid wastes almost come with every production process. Multi-million tons, if not billion tons, of solid wastes are being generated globally each year. These solid wastes are lowvalue materials in general, and often have very limited markets. As a matter of fact, many of these solid wastes have been stored on site or have been disposed of at landfills for many years, not only occupying lands, but also polluting environment. Therefore, effective and efficient recycling of solid wastes has been a very challengeable task and has played a very important role in environmental protection.One of the major barriers which hinder recycling of solid wastes is contamination of the solid wastes with some undesired components. These undesired components are components which are not wanted by production processes or applications where the solid wastes are consumed or recycled, since the undesired components often degrade qualities of the solid wastes, imposing negative effects on operations, facilities and product qualities of the production processes or applications. Sometimes, the undesired components may also pose severe environmental concerns. When undesired components are present in solid wastes at over-limit levels, the solid wastes tum to become destructive, useless and non-recyclable. Consequently, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes."

Jan 1, 2014

By Chang Wei, Fan Zhang, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Marmatite is an important resource of zinc, which exist in forms of high iron and high indium. In order to recycle the valuable metal from these ores, the testwork of simultaneous leaching on neutral residue mixed with zinc concentrate of high iron and high indium has been conducted. The primary objectives are to leach the zinc and indium remaining in the neutral leach residue as ferrite using acid, and to reduce the ferric iron in solution to the ferrous by zinc concentrate, thereby extracting the zinc and indium in the zinc concentrate. The results indicated that in the following conditions, mass ratio of neutral residue to zinc concentrate of 1:0.25, particle size of 74-58 μm, initial sulfuric acid concentration of 150 g/L, liquid to solid ratio of 8 L/kg, temperature of 90°C, reaction time of 4h, the leaching efficiency of zinc and indium were over 95%, nearly 90% Fe was Ferrous in the leaching solution. This process effectively extracted zinc and indium and converted Fe3+ into Fe2+ in solution, and simplified the traditional process of reduction after leaching.

Jan 1, 2016

By Dariusz Kopyci ski, Józef Dorula

The study proves that by introducing the iron powder and disintegrated steel scrap to low-sulphur cast iron still before the inoculation carried out with a conventional graphitising inoculant, the mechanical properties similar to those obtained during the inoculation treatment carried out on cast iron with the recommended high sulphur content are achieved. The said operation increases the number of crystallisation nuclei for dendrites of the primary austenite. In this case, the iron particles act as substrates for the nucleation of primary austenite, due to a similar crystallographic behaviour of the regular face centred cubic lattice The more numerous are the dendrites of primary austenite, the less free space is available in the interdendritic spaces for the formation of graphite eutectic grains, which makes the structure more refined (more eutectic grains) and the mechanical properties higher.

Jan 1, 2016

By Guo Chang Jiang

In order to improve the IIAZ toughness of X-60 pipe steel, the intragranular ferrite plate (IFP) technology was used. The characteristics of IFP is claimed to be much fine ferrite plates appear inside the original austenite grains. By means of suitable Re, Zr, Ti additions in a bath with a higher initial oxygen potential, a good control of the peak temperature and the cooling rate during welding simulation, one can get a %IFP in volume over 50%, and the toughness gets up from 55 J to 160 J. It was found that the inclusions most effective in nucleating IFP are some deformable complex silicates which either entrap Re, Zr, Ti oxides or contain these elements. The greater the number of the evenly distributed and effectively nucleating inclusions, the more the %IFP in volume, and the finer the microstructure of the HAZ, so the better the relevant toughness. Generally, these silicates bahave as fine spheres along a line. The present authors revealed that these fine spheres result from the remelting of the shuttle- like silicates due to heating in the process of welding simulation. These silicates used to get a higher sulphur capacity, so MnS deposits might be observed on the periphery of the silicates. IFP was proved to be directly rooted in the [Mn] depleting zone which locates beside MnS deposits.

Jan 1, 1997

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A PFS(polymeric ferric sulfate) coagulation-photocatalytic oxidation technology was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on TOC removal rate were investigated, and the results were compared with those of the common photocatalytic oxidation technology under the operating parameters of the photocatalytic oxidation defined. Single factor experimental results showed that TOC removal rate could reach 81%, when optimal operating conditions were as follows: TiO2 loading: 4.0g/L, irradiation time: 4h, initial pH is 5.1and PFS dosage:700mg/L. PFS coagulation and photocatalytic oxidation have synergistic effect, which is meaningful for highly efficient treatment of coking wastewater

Jan 1, 2015

By Shane Andrews, Gustavo Vasquez, S. K. Varma

"The effect of solutionizing time on the corrosive wear behavior of 2014 aluminum alloy has been studied using the impact and continuous mode of scratching techniques. The transient currents (TC) evolved during the scratching of the alloy shows a linear dependence between the TC and the solutionizing time. Higher TC values at longer solutionizing time may be associated with the changes in the concentration of quenched-in vacancies, grain sizes and dislocations generated during scratching. These factors can either create (a) anodic sites or (b) pitting corrosion resulting in the generation of transient currents. The results have been compared with the similar study carried out for 6061 aluminum alloys. This 6061 aluminum alloy shows similar behavior but the rate of TC generation per unit solutionizing time is much lower than 2014 aluminum alloy. The morphological changes in the impact scratches and the TEM investigation in the scratch have been presented in this paper.IntroductionThe technique of studying corrosive wear of composites of 6061 aluminum in the monolithic and reinforced forms has been reported in the literature [1]. Two modes of scratching, consisting of impact and continuous, in a corrosive environment indicate that the composites, containing 0.10 and 0.20 volume fractions of alumina particles (VFAP), have higher corrosive wear rates than the monolith. A graph between the transient current (TC) generated during the impact scratching as a function of solutionizing time at 540°C indicates linear relationship between them. A similar slopes for the composites were observed and the TC values were less for the composite containing lesser VFAP."

Jan 1, 1998

By Jae-Chun Lee

Di-2-ethylhexyl phosphoric acid (D2EHPA) is widely used for separating rare-earth elements. In commercial plants, rare-earths are usually stripped from loaded extractant streams using mineral acid, then precipitated as oxalates. Many rare-earth uses demand specific powder characteristics, which are obtained by secondary processing. This paper demonstrates the feasibility of combining the stripping, precipitation and powder processing stages, thereby achieving considerable savings. MEHPA solutions were loaded with yttrium, then emulsified with oxalic acid-HC1 solutions to precipitate yttrium oxalate, which was readily calcined to yttrium oxide. The precipitation kinetics and yield were sensitive to process conditions. The morphology and size of the yttrium oxalate powders varied with the concentrations of D2EHPA and oxalic acid, and the presence of SPAN 60, which affected nucleation, growth, and the emulsion characteristics.

Jan 1, 1992

By Tuneo Funahashi

Sumitomo Shisaka Works has been treating EAF(Electric Arc Furnace) dust to recover zinc and lead in the Waelz Kiln process. Since its commencement of operation in 1977, many technical improvements have been successfully made to increase the production capacity and the zinc recovery rate. The EAF dust charge to the Waelz Kiln was increased from 35,000tly to 120,00OtIy, and the production of zinc oxide now amounts to 40,000tly. The zinc content in the clinker was decreased from 5% to less than I%, by the optimization of the kiln heat pattern with no accretion trouble. And the clinker has become more a valuable raw material for steel making. This paper describes the above progress ofthe SMM Waelz Kiln process operation at the Shisaka Works.

Jan 1, 1998

By Kohei Yajima

The dusts and fly ash generated from the steelmaking processes and municipal solid waste incineration processes contain metallic elements such as Fe, Zn, Pb and Cd with considerable amount of halogens. In Japan, zinc in dusts is recovered by Waelz kiln or MF process, etc. However, the presence of halogen in the dust affects the evaporation and condensation behavior of zinc and other metals, and disturbs the direct recycling of dust to steelmaking processes, because alkali or heavy metals reacted with halogen vaporize easily as halides and/or oxyhalide compounds in pyrometallurgical process. Recently, the formation mechanism of zinc oxychloride vapor was investigated and the formation of zinc oxychloride such as ZnOCl was proposed. However, considering the practical operation, the effect of water vapor on the evaporation behavior of oxychloride is not fully clarified yet. This study is focused on the investigation of evaporation behavior of ZnO with Ar- O2-HCl-H2O atmosphere.

Jan 1, 2008

By Gjergj Dodbiba, Atsushi Shibayama, Toyohisa Fujita, Takashi Shikazumi, Yukio Kato, Kenji Murata

"A new crushing or liberation technique by means of underwater explosion is put forward. This technique is suitable for crushing and liberating various materials, for instance: the electric parts of the discarded portable telephone, CPU from mother-boards of PCs, steel from plastics tubes used as construction materials, waste constructed materials like panels, tungsten carbide scraps, as well as slitting the optical disk (e.g. DVDs), etc. The materials to be crushed are immersed in water and then the explosion is carried out by using only a small amount of explosive. The shock waves in combination with the generated bubbles are very effective in liberating the materials of different densities. It was observed that the metals crushed or liberated by using this technique were leached much faster when compared with the conventional crushing technique. This crushing method can be applied for liberation of many kinds of electric or mechanical tools. Introduction The explosive has been used since Nobel’s invention in 1866. The main practical application of explosion is in the large scale public works, such as dam construction, land development, tunnel, mining and dismantlement of building. The shock wave caused by explosion extremely can generate high pressure able to break the concrete and rock, and other materials. In this study, the crushing and liberation of waste materials was carried out by explosion in water. The idea was to use this technique as a pretreatment stage prior to recycling. The explosion in water can be used to crush hard materials, helping the liberation between different attached materials. The samples used in this experimental work are waste materials such as construction materials, hose, cemented carbide, cellular phone, lithium buttery, DVD-R, etc."

Jan 1, 2008

By Wilky Desrosin, Alicia E. Ares, Carlos E. Schvezov

"In the present research the horizontal directional solidification Zn-Sn alloys (Zn-4wt. %Sn, Zn- 6wt. %Sn, Zn-10wt.%Sn and Zn-30wt.%Sn) was carried out by extracting heat in two opposite directions. For this purpose, ceramic molds, a muffie, a horizontal furnace with two heat extraction systems at the ends, a measurement, acquisition and recording temperature system, eight K-type thermocouples and an electronic recorder were used. The main parameters involved in the columnar-to-equiaxed transition, CET, were: the moment of start and end of solidification at each position under consideration, cooling rates, the average temperature gradients and critical temperature gradients at the CET, the average speed of liquid and solid interphases left and right, advancing in opposite directions. Also, solidification kinetics was found to be different between horizontal solidification two-way heat extractions, with preliminary results of the vertical unidirectional solidification. In the solidification experiments, the velocity and accelerations of the liquidus and solidus interphases usually occurs at the end solidification zone of the samples.IntroductionSolidification of metal alloys, which starts in the external equiaxed region (chill), results in two basic types of structures in a single solidified alloy sample: columnar and equiaxed. The presence of both structures indicates the occurrence of the colunmar-to-equiaxed transition phenomenon[!].Studying the colunmar-to-equiaxed transition, CET, is of great technological interest for the evaluation and design of the mechanical properties of the solidification products. To this end it is necessary to understand the mechanisms by which it occurs. As found in previous studies [2-5], the CET occurs by competition between columnar and equiaxed growth. Mainly is controlled by the parameters of casting, such as the alloy composition, the density of the present nuclei in the liquid, the cooling capacity of the metal I mold, and the degree of convection in the liquid [7-10]."

Jan 1, 2014

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior ofTiO2 nanopartic1es was thermogravimetrically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanopartic1es, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500°C at a heating rate of 1 C°/min. The weight increase curve showed a maximum of ca 30 wt% at around 750°?C and then gradually decreased to ca 12 wt% at 1000°C. This would be caused by the formation of TiS2 followed by the decomposition ofTiS2 to lower sulfides, such as Tit.0.8S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanoparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By Pradeep kumar Jha, Manas Mohan Mahapatra, Sabin Kumar Mishra, Satish Kumar Ajmani, Satish C. Sharma

"Due to mechanical/ electrical failure in the C.C. line or inadequate availability of molten steel from coming ladle, sometimes one/two outlets of a multi-strand tundish in continuous casting unit is closed. Closing any of the outlets affects the flow distribution inside the tundish which in turn governs the quality of steel coming out. Hence it is important to study which of the outlets should be closed to have proper results in terms of flow behavior and inclusion removal inside the tundish. Present study aims at finding the effect of closing one or two outlets on flow behavior and inclusion removal in a multi strand tundish. It was found that closing the near outlet (outlet near to the inlet) increases the inclusion removal tendency than closing the other two outlets in a six-strand billet caster tundish (only three outlets are considered because of symmetry).IntroductionContinuous casting process transforms molten metal into solid on a continuous basis. This process is the most efficient way to solidify large volumes of metal into simple shapes for subsequent processing [1]. Molten metal is tapped into the ladle from furnaces. From the ladle, the hot metal is transferred via a refractory shroud (pipe) to a holding bath called a tundish. The tundish allows a reservoir of metal to feed the casting machine while ladles are switched, thus acting as a buffer of hot metal as well as smoothing out flow, regulating metal feed to the moulds and cleaning the metal [2]."

Jan 1, 2012

By Samir N. Shoukry, Mourad Y. Riad, Gergis W. William

"Setting of concrete material is defined as the transitional period between states of true fluidity and true rigidity. Initial and final setting times are measured in the laboratory on the mortar sieved from the mix in a controlled environment where temperature and moisture values are constant. On the other hand, field applications are held in outdoor environments where environmental variations have direct impact on setting time values. In this study, initial setting time of class K concrete, usually used for bridge decks and concrete pavements, are investigated highlighting discrepancies between laboratory and field measurements. 72 mixes have been cast in variable environments and collected data from concrete mixes and the ambient conditions are reported. In light of the collected data, the effects of variable setting times on early age cracking of concrete material are studied and means to minimize such cracks are presented.BackgroundSetting of concrete material is defined as the transitional period between states of true fluidity and true rigidity [1]. Continuous hydration of the cement within the matrix transfers the mix from a state of setting to hardening. Initial and final Setting times are measured in a laboratory setting following ASTM C 403 specifications. Initial setting approximates the time at which the cement paste can no longer be plastic under compaction (or can be handled in a proper fashion), while the final setting approximates the time at which hardening occurs. The standard test described in ASTM C 403 is conducted on the mortar sieved from the mix (paste passing from 4.75 mm sieve opening). Initial and final settings are described as the elapsed time after the initial contact of water and cement till the mortar reaches a penetration resistances of 3.5 MPa (500 psi), and 27.6 MPa (4000 psi) respectively."

Jan 1, 2012