Search Documents

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering material. Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to design new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass spectrometer.

Jan 1, 2003

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Takeshi Azakami

By combining the iron reduction process with the usual rotary kiln process, the direct production of metallic zinc from EAF dust is proposed. After thermodynamic estimation and desk-top experiments it is confirmed that the process is hopeful under suitable conditions. In order to get some practical test data the enlargement of the process scale was planned and the bench scale tests were carried on successfully. In these experiments a zinc ingot of PW grade was produced from EAF dust.

Jan 1, 2003

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By Gökhan Demirci, Ishak Karakaya

"Energy consumption in electrolytic magnesium cells is well above the theoretical values. However, the mechanism of the back reaction, the main cause of the current losses, has not been fully understood yet. Magnesium dissolution into the melt is generally regarded as the limiting step for the back reaction. Accordingly, present cell designs are made with priority given to fast magnesium removal from the cell. However, experimental data and modeling results in this study indicate that the limiting step for the back reaction between magnesium and chlorine is the chlorine dissolution into the electrolyte when physical contact between electrolysis products was eliminated. Effects of chlorine bubbles on the current efficiency and the cell potential were investigated. Results show that the extent of back reaction is proportional to the chlorine surface area in contact with the electrolyte per unit time, and the cell potential increases with the amount of chlorine bubbles inside the electrolyte.1. IntroductionMagnesium is less dense than the electrolyte in electrolytic magnesium production. Therefore, both electrode products, magnesium and the chlorine gas, move upwards inside the molten salt electrolyte during electrolysis. The upward motion of electrode products promotes the most important current loss mechanism, the ""back reaction"". Separation of the highly reactive species; liquid magnesium and the chlorine gas in the cell, to prevent their recombination is one of the main concerns in cell designs. The employment of large inter-electrode distance or a separation wall in early cell designs; decreased the extent of recombination, but increased the cell voltage and energy consumption. Recent cell designs, on the other hand, make use of lifting action of chlorine gas [1,2] by utilizing smaller inter electrode distances to separate the magnesium and chlorine gas faster. Although energy consumption was reduced, but more physical interactions between electrode products make electrolytic magnesium cells still highly inefficient when energy consumptions are compared with the theoretical values. Today, the most efficient industrial cells utilizing high purity feed operate at 10.5-11.5 kWh kg-1 Mg [3-5] and it is considerably higher than the theoretically attainable value of about 6.0 kWh kg-1 [6]. This large gap demonstrates the necessity of more research on physics and chemistry of magnesium cell electrolysis."

Jan 1, 2011

By J. Chen Kuriyama

One method to store hydrogen effectively involves the use of metal complexes such as the alkali-element aluminum hydrides. The hydriding/dehydriding properties of these materials depend on how to prepare them with different structures and microstructures. The present work focused on a high-energy ball milling technique to produce Ti-doped lithium tetrahydridoaluminate (LiA1H4) and lithium hexahydroalanate (Li3AIH6) powders with nanocrystallites. The phase structures and dehydriding/rehydriding characteristics were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Brunauer-Emmett-Teller measurement, thermogravimetry, and differential scanning calorimetry. The mechanism of dehydrogenation and rehydrogenation was also examined by means of X-ray photoelectron spectroscopy (XPS). The results on the relation between the reversible hydrogen storage and catalysis function of the Ti-doped complex hydride indicate that both the homogenous distribution of Ti+AI nanoclusters and the Ti¬catalyst with Ti e> Ti3+ (Ti0/Ti2+/Ti3+) defect sites play important roles in optimizing the reversible hydrogen storage.

Jan 1, 2002

By Jun Miao, Kang Liu, Jilai Xue, Jun Zhu

CO2 emissions must be reduced by at least 50 % by 2050, and hence the technical solutions to capture and convert CO2 into value–added products should be considered. A Cobalt(III) Schiff base complex (Salen–Co(III)) has been investigated as a catalyst for synthesis of cyclic carbonate from CO2 and epichlorohydrin(ECH) with tetrabutylammonium bromide (TBAB) as co–catalyst. To recover Salen–Co(III) for the next cycling operation, it was immobilized onto zeolite 13X through excessive impregnation method. The immobilized catalyst was characterized using XRD, SEM, BET and ICP–AES techniques. Catalytic tests showed that yield of cyclic carbonate reached 90 % using 0.5 mol % Salen–Co(III) at ambient conditions. The immobilized Salen–Co(III) exhibited better catalytic activity than the homogenous one when used at the first cycle, but the yield decreased by some 20 % after five cycles.

Jan 1, 2015

By Seiji Yokoyama

As a series of fundamental study on the gas evaporation method, a levitation-melted aluminum was evaporated in the gas mixture of argon and ammonia to synthesize ultrafine particles of aluminum nitride. When the ammonia partial pressure were more than 2kPa, the formation ratio of aluminum nitride was about 95%. The particles of aluminum nitride were mainly hexagonal. The mean size of the particles of aluminum nitride was about 57 nm, and it was constant without depending on the temperature of the levitated aluminum and the partial pressure pf ammonia. The aluminum nitride was formed by the reaction between ammonia and condensed liquid aluminum particle whose size was relatively small.

Jan 1, 2006

By H. Masuda

The lijima Zinc Refinery started operation in 1972, and has today an annual capacity of 200, 000+-Zn. The hematite process was employed for the first time and the ideal of waste-free refinery has been pursued for 30 years. In recent years, however, only half of the hematite produced would be sold to the cement industry and hence a reduction of arsenic level has been necessary in order to sell the entire amount produced, The arsenic cementation process with zinc powder, developed through a long time laboratory research was found among some options as the best for the hematite process. The construction work started in 2000 and the facility was put into operation in 200 I. As a result in the same year all hematite were sold to the cement industry. The outline of this project, present operations and technical issue are reported in this paper.

Jan 1, 2003

By Takayuki Watanabe, Yoshiki Shimizu, Yusuke Moriyoshi

"B-C-N nanotubes prepared by a flush evaporation method using a de arc plasma were mainly characterized by transmission electron microscopy (TEM) and electron energy· loss spectroscopy (EELS). The nanotubes obtained· were divided into three types such as carbon boron nitride and carbon or carbon nanotubes surrounded with boron nitride nanotubes. These types of nanotubes were obtained at higher temperatures than about 3000 K, however, these were not formed at lower temperatures than about 3000K. On the other hand, 11anocapsules were· formed at all the experimental temperatures and nanocapsules with a homogeneous phase were obtained at lower temperatures than about 3000 K. The effect of additives on the formation of B-C-N nanotubes was not clear. Based on these experimental data depending on temperatures and corresponding microstructures, the formation mechanisms of both nanotubes and nanocapsules were briefly .discussed 1 Introduction As reported previously, nano tubes have unique electrical properties1, 3) The preparations of nallotupes have been usually carried out by flush evaporation methods using either a de arc plasma or a laser4 -5) By these methods the reaction rate is so rarid that we have no data of intermediate products between initial raw materials and. final products of nanotubes 6-9). So, the formation mechanisms of nanotubes have been mainly speculated only from the microstructures of resultant nanoiubes. In order to have more reliable formation mechanisms, it is particularly important to have the information of intermediate products at the corresponding temperatures. From the viewpoints, we have studied about the effects of temperatures on the preparation of nanolubes. Here we report mi firstly some problems on the preparation of B-C-N nanotubes 10), secondly the effects of temperatures on the preparation of B-C-N nanotubes, and finally the formation mechanisms of nanotubes."

Jan 1, 2000

By Riyad N. Ahmad-Bitar, Shadia J. Lkhmayies

"CdSi-xTex thin films were prepared by first producing CdS:In thin films by the spray pyrolysis (SP) technique and then annealing the films in the presence of Te vapor in nitrogen atmosphere. X-Ray diffraction (XRD) measurements showed that the films are polycrystalline with the wurtzite structure. Transmittance measurements were recorded at room temperature in the wavelength range 400-900 nm and used to deduce the absorbance. The first derivative of the absorbance was calculated and used to find the values of the bandgap energy, where more than one bandgap was obtained for each film. These results show that the films are inhomogeneous or the composition differs with location. The photoluminescence (PL) was recorded at T = 60 K and a deconvolution peak fit was performed for each spectrum. The results of the PL spectra are consistent with those obtained from the first derivative and confirm the inhomogeneity of the films.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The CdS/CdTe interface plays an active role and a detailed knowledge of its properties is crucial for thorough understanding of the device. High efficiency devices have been obtained in spite of the large lattice mismatch (9. 7%) between hexagonal CdS and cubic CdTe. Interdiffusion at the CdS/CdTe interface is considered to affect the performance of the devices [1]. The formation of a mixed crystal or a graded layer at the interface causes a reduction in the lattice mismatch at the CdS/CdTe junction [2] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [3, 4].The objective of this work is to investigate the transmittance, photoluminescence (PL) and structure of CdSi-xTex thin films prepared by annealing the spray-deposited CdS:In thin films in the presence of tellurium vapor. X-ray diffraction (XRD) was used for exploring the structure. Transmittance is used to deduce the absorbance where its first derivative was used to find the bandgap energy which varies with composition. The evolution of the PL spectra as functions of tellurium concentration was evident and it confirmed the inhomogeneities of the films."

Jan 1, 2011

By Tetsuya Uda, Sakae Shirayama

"With the aim of producing nickel (Ni) metal directly from acidic aqueous solution containing cobalt (Co) and other impurities, selective reduction of Ni was examined. As a preliminary experiment, sodium hypophosphite monohydrate (NaH2PO2·H2O) was selected as a reductant, and reacted with aqueous solution containing 0.1 mol L-1 nickel sulfate (NiSO4·6H2O) and 0 ~ 0.05 mol L-1 cobalt sulfate (CoSO4·7H2O) for 3 hours at 90 °C. As a result, it was revealed that Ni was selectively reduced and separated from Co in the acidic region (pH= 4.8). In this study, differences of reduction behavior between Ni and Co were investigated, and the feasibility of Ni I Co separation by the selective reduction of Ni was discussed.IntroductionEfficient Ni condensation and separation from Co are essential in nickel hydrometallurgical processes. Currently, the hydrometallurgical production of Ni from oxide ore is mainly carried out by acid leaching at elevated temperature, followed by the removal of impurities using neutralization, and condensation of Ni and Co into intermediate products such as hydroxides and sulfides. Then, the intermediate product is dissolved in acid aqueous solutions, and Ni I Co separation is conducted by solvent extraction. Finally, Ni and Co are recovered by electro-winning. This complicated process consumes large amounts of alkali, hydrogen sulfide (H2S), and organic solution in a multiple-staged process'. To reduce the consumption of these chemicals, it is important to recover Ni more efficiently from acidic aqueous solution containing impurities."

Jan 1, 2014

By Patrick R. Taylor

Iron phosphate glasses are promising host matrices for vitrifying actinide rich nuclear wastes materials because of their high solubility of actinide oxides, high chemical durability, and relatively low melting temperatures. An iron phosphate waste form was developed at the University of Missouri-Rolla. The structure and property of the waste form were well characterized by materials techniques. However, to scale the process and advance it to commercial viability, it is necessary to understand the processing parameters, such as the partitioning of waste elements and the viscosity as a function of temperature. Viscosity of 40 Fe203 - 60 P205 mole % iron phosphate melts (prepared with phosphorous pentoxide and ferric oxide) at 1000-1200 C was measured by the rotating-spindle method. It was discovered that this fluid has non-Newtonian behavior. Experiments were performed to study flow properties following the Standard Test methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield) Viscometer (ASTM D 2196-86). Samples prepared using ammonium phosphate and ferric oxide showed Newtonian behavior and the temperature dependence of the viscosity was studied over the range of 1000 to 1200 degrees C. The difference in flow behavior between the two fluids was analyzed in terms of preparation conditions and variation in the final composition and phases. The partitioning behavior of waste elements in the iron phosphate glass was studied by melting in a high temperature furnace and JCP analysis. The experimental results show that the solubility of Ce and Sr in phosphate glasses is significantly higher than the solubility associated with borosilicate glasses. This strengthens the conclusion that iron phosphate may be a viable alternative to borosilicate glass for immobilization of high heavy-metal-content wastes and actinide rich wastes.

Jan 1, 2002

By Junji Shibata

As one of the effective usages of various wastes discharged in non-ferrous metal industry, the synthesis of hydrotalcite was carried out using aluminum dross as a raw material. Hydrotalcite is one of the inorganic anion exchangers and has layered structure of complex hydroxide. The removal of toxic metal ions such as As(III), As(V), Cr(VI) and Se(IV) with the hydrotalcite was investigated, and the removal properties were compared from the viewpoint of the anion exchange amount and exchange rate. Hydrotalcite can be obtained by a co-precipitation method from the aluminum dross and the waste MgCl2 solution discharged in an aluminum regeneration process. Slight amounts of SiO2, Al2O3, Fe2O3 and so on remain in the reaction product as an impurity component. Interlayer distance of the obtained hydrotalcite is about 0.3nm. Hydrotalcite changes to Mg-Al oxide by the calcination at 773K for 3h, and then hydrotalcite is formed again by a rehydration operation after calcination. The toxic metal ions are removed from aqueous solution by the anion exchange reaction in the pH region where toxic metal ions exist as the anionic species like AsO2-, HAsO42-,CrO42-, and SeO32-. The exchange amount is considerably concerned with the valence of anionic species and the size of anionic species. The removal of toxic metal ions were investigated from the engineering aspects such as the low concentration limit to be removed, the amount of hydrotalcite to be used for the perfect removal of toxic metal ions and so on.

Jan 1, 2006

By F. W. H. Dean

A very sensitive sensor for the detection and measurement of hydrogen in solid steel is described. This technique is non-invasive and uses a collector to sweep the hydrogen emanating from a steel surface and feed to it sensor. This method is particularly sensitive, resolving fluxes to < 2 pI cm?2 S?I, with a linear measurement up to 1000 pI cm&apos;2 S?I, The collector is held on the steel substrate by magnets and it is shown that emanation of hydrogen from the steel is controlled by bulk diffusion of the hydrogen through the steel. The technique is demonstrated to have an excellent response time and reproducibility.

Jan 1, 2001

By Masayasu Kawahara

"The extraction and separation of nickel, cobalt and copper were investigated with a solvent impregnated resin which was produced from UX84-I and XAD-4. The extraction behavior of metals with the solvent impregnated resin is similar to that with solvent extraction. The extraction ability of solvent impregnated resin improves when using finer particle resin and with a higher concentration of extraction solvent.IntroductionSolvent extraction is well known-as a method for separation of metallic elements in solution. However there are problems with intermediate phase and solvent loss. Ion exchange resin is also used in hydrometallurgy, but it is not fit for separating a large quantity of metals. Amberlite XAD-4 resin is known as a absorption agent of organic matter in water. It is expected that the resin which has the ability of extracting metals can be made by absorbing organic extractant on XAD-4 resin In this study, solvent impregnated resin (SIR) was produced from LIX84-I and XAD-4, and extraction and separation of nickel, cobalt and copper were conducted using SIR. The extraction properties of SIR were investigated, and a comparison between ordinary solvent extraction and SIR was made.Experimental ProcedureAmberlite XAD-4 was used as absorption resin for the organic extractant in this study. The physical properties of XAD-4 are shown in Table I. Amber lite XAD-4 has a large surface area and shows good ability to absorb organic matter in water, but the: resin does not have the ability of exchanging metallic ion."

Jan 1, 2000

By Wei Yin, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

Copper anode slime is an increasingly significant resource for precious metals such as Au, Ag and Pd. The extraction of Au, Ag and Pd from decopperized anode slime by different pretreatments and different lixiviants including cyanide, chloride, thiourea and thiosulfate have been investigated. When oxidizing roasting pretreatment was carried out under the conditions of roasting time 120min and temperature 625 ℃, the removal ratios of S and Sb could reach 82.18% and 98.52%, respectively. And the following alkaline leaching of calcine could result in the dissolution of 46.40% Cu and 98.48% Pb. The optima leaching ratios of Au, Ag and Pd reached 99.48%, 97.69%, 94.79% by cyanide leaching, and 95.01%, 79.84%, 96.59% by chloride leaching, and about 95.21%, 95.66%, 48.79% by thiourea/thiosulfate leaching.

Jan 1, 2015

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By J. M. Demarthe

The recovery of minor metals from zinc concentrates is dependent on the process used for their treatment. The behaviour of gennanium and indium in pyrometallurgical processes such as the Imperial Smelting furnace or the cupola furnace is of practical importance. The .Anaconda process for the treatment of zinc leach residues is not well suited to the recovery of valuable minor metals, and new technologies must be studied. In this regard, a solvent extraction process, using Kelex 100, developed by Minenet Recherche for the recovery of gennanium from dilute sulphate leach solutions is described. Also, new hydranetallurgical techniques in chloride media can be applied to the purification and concentration of minor metals depending on the stability of their chloro-complexes and the valency of associated inpurities. A synthesis of methods is proposed to address the problems related to the recovery of valuable minor metals in the zinc industry.

Jan 1, 1990

By Zhang Jianliang, Xu, Zuo, Runsheng, Haibin, Kexin, Jiao

Full oxygen blast furnace iron-making is one of the new technologies, which is most likely to realize large-scale application. In this paper, based on the technology of full oxygen blast furnace, the reduction behavior of pellets is studied systematically by using the analytic method of non-isothermal dynamics on the different atmosphere(CO,H2) and the dynamics model of gas-solid reduction reaction is constructed, which lay the foundation of reduction model establishment of full oxygen blast furnace burden. The result shows that the time of pellets which began to react is delayed with the increase of the content of H2. When the temperature is between 650 'C and 1050 'C, the content of H2 in the reduction atmosphere is larger, and the rate of the reduction pellets is larger. The reduction rate changes at 780 'C, and a certain amount of H2 in the reducing atmosphere will significantly improve the reduction reaction when the temperature is above 780 'C. Non-isothermal reduction behavior is controlled by interfacial chemical reaction and internal diffusion under high reduction potential. H2 ratio in reducing atmosphere increased from 0% to 100%. The reduction reaction of the apparent activation energy decreased from 49.03kJ-mor1 to 33.74kJ·mor1.

Jan 1, 2013