Search Documents

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000

By Tatsuo Itou

Both sales volume of Aluminum Can and its recycling rate are remarkably increasing here in Japan. In 1993, recycled can volume was 11.78 billion cans ( 116,258 metric tons ) and its recycling rate 57.8 percent. We, MITSUBISHI MATERIALS CORPORATION. the leading manufacturer of aluminum can in Japan and our affiliated companies are very deeply involved in recycling used beverage cans ( U.B.C ) and recycling them back to can stock. In this paper. I would like to present the following; 1. Recent trend of beverage can consumption in Japan. 2. Trend of aluminum can and its recycling rate in Japan. 3. Future of aluminum can business in Japan.

Jan 1, 1995

By Rui-Qing Li, John G. Peacey, Peter J. Hancock

"Noranda has been investigating a pyrometallurgical process for the direct recovery of zinc from zinc concentrate and zinc and iron containing residues. The process consists of injecting dry zinc concentrate and secondary zinc materials into a molten iron oxysulphide bath, volatilizing metallic zinc into furnace off gas essentially free of sulphur or S02, fixing sulphur contained in the feed materials as iron oxysulphide matte which is disposed, and recovering metallic zinc in an ISP type lead splash condenser. Combustion of petroleum coke with air or oxygen enriched air inside the oxygen containing matte supplies part of the heat, and the products of combustion dilute the zinc-laden gas to a desired level.This paper describes the process concept, thermodynamic background, experimental tests, mass and heat balance calculation for a conceptual flowsheet, environmental stability of the residue and advantages and disadvantages of the process. Experimental tests have successfully proved the process concept and thermodynamic predictions. Direct smelting of zinc concentrate and residues inside an iron oxysulfide bath has a great potential to become a cost effective and flexible zinc smelting process.1. INTRODUCTIONZinc is mainly produced by a roast-leach-electrowinning process route, which accounts for about 80% of the world primary zinc production. This process produces high quality zinc with very high zinc recovery (>95%) but suffers from several major drawbacks such as using high cost electricity as reductant, producing environmentally problematic iron containing leach residue (jarosite or goethite) and the difficulty in treating secondary zinc feed materials containing high impurity levels, such as electric arc furnace dusts from the steel industry, and other complex sources. Also in some areas, markets for sulphuric acid are distant resulting in negative realizations on acid sales.The Imperial Smelting Furnace (ISF) process is the major pyrometallurgical process to treat zinc-lead concentrate. The advantage of this process over the electrolytic zinc process is its flexibility in treating high-lead, bulk concentrates with high recoveries of lead, copper and precious metals. However, this is a two-stage process involving sintering of Zn-Pb concentrates followed by blast furnace reduction. The process requires large amounts of high-quality coke which is a major operation cost, and the sintering process which results in serious environmental problems."

Jan 1, 1996

By G. Mawire

The extraction of scandium from its oxide with a task specific ionic liquid [Hbet][Tf2N] offers potential advantages of lower energy consumption, recycling of the extractant and reduced environmental impact compared to conventional methods. In this paper, the influence of reaction temperature, solid to liquid ratio and water to the ionic liquid ratio on the extraction of scandium from a synthetic scandium oxide (Sc2O3) system was studied. The influence of investigated parameters on leaching was very significant as approximately 98% scandium was extracted from its oxide after 72 h. Furthermore, the ionic liquid also selectively extracted 47% scandium after 48 h from a mixture of pure metal oxides containing oxides of tantalum, niobium, and scandium. The research demonstrated the potential of [Hbet][Tf2N] to selectively extract scandium from columbite processing tailings and other scandium bearing ores like Ixiolite, Heftetjernite and Tantalite which predominately contain tantalum and niobium.

By Kaixi Jiang, Lan Li, Bang Wei, Haibei Wang, Yaping Feng

"China is currently the world's largest copper producer. In the last five years, 950 kt/y of smelting capacity was commissioned. Currently, about 1200 kt/y smelting capacity is under construction and about 2000 kt/y smelting capacity is under feasibility study. Ausmelt/ISA smelting and flash smelting technologies were commonly adopted in China. After the double-flash-smelter was first adopted in 2004, three new double-flash-smelters are scheduled. Recently, two new copper smelting technologies were developed in China. One is an improved bath side-blown smelting process, and another is the SK.S bottom blowing process. Both technologies have been in practice for over three years and have achieved good technical performance. Approximately 500 kt/y new smelting capacity in China and India will adopt these technologies. Both technologies have the advantages of low investment cost, low energy consumption and high flexibility for complex raw materials. This paper reviews ""green"" copper smelting projects in China and introduces the practices of the two new Chinese smelting technologies.IntroductionPresently, China is the largest copper producer in the world. As far as the smelting of copper is concerned, there are many smelting processes applied in industrial production, such as flash smelting, Noranda smelting, Ausmelt smelting, Isa smelting, the Mitsubishi process, Vanukov smelting, silver copper-smelting, SKS smelting, both side-blown smelting, traditional blast furnace smelting, electric furnace smelting, reverberatery smelting and so on . Except the last three traditional processes that are eliminated because of their failure to meet the requirements for environmental protection, all of the other above-mentioned methods are advanced smelting processes adopted nowadays."

Jan 1, 2012

By Yuanbo Zhang, Ruijun Wang, Qian Li, Zhao Jing, Guanghui Li, Zhengwei Yu, Chen Liu

The high content of sodium and potassium in sinter is harmful for blast furnace ironmaking. Reductive sintering technology can remove more alkali metals than conventional sintering process. In order to improve the removal ratios of Na and K, reductive sintering with both CO-containing flue gas circulation and carbon-bearing pellet was conducted in this study. Experimental results show that all indexes except the VSV and P were improved in reductive sintering with CO circulation. Flue gas circulation technique combined with carbon-bearing pellets were beneficial to reductive sintering, because it could maintain good sintering indexes and enhance the removal of Na, K. The best removal ratios of Na, K and reduction degree of iron oxides were 20.37%, 63.73% and 23.76%. In reductive finished sinter, silicate mineral becomes the important binder phase, and main iron mineral phases are wustite (FexO) and magnetite (Fe3O4).

Jan 1, 2016

By Xu Zhang, Xuewei Lv, Guibao Qiu

Slag foaming phenomenon is of vital importance to the mass and energy transfer in metallurgical processes. A considerable extensively studies carried out via out-gas in the past cannot simulate well the foaming phenomenon formed in the blast furnace where high TiO2 iron ore is used. A gas reaction was designed in the water-glycerol system to simulate the inner-gas system. This study investigated the influences of solution viscosity, particle concentration and particle size on foaming caused by endogenetic gas. The results show that the foaming height decreases with the increase of solution viscosity, which means reduced foaming ability, more difficult foaming elimination process and prolonged time for natural defoaming. With increasing the solid particle content, the foam height presents a trend which increases firstly and then decreases. Under a certain solid particle content, foaming height decreases with the increase of solid particle size, indicating a weak foaming ability.

Jan 1, 2015

By Shenghui Guo, Ying Lei, Hao Niu, Huilong Luo, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the combination of microwave drying (MWD) and heat pump drying (HPD) drying experiments were designed by response surface methodology (RSM) based on central composite design (CCD) using design expert software (Version 7.15), and the process parameters were optimized. The conditions given by software are: the MWD time is 4.6 or 4.4 min; the HPD time is 9.0 or 8.6 min; and the sample mass is 620 or 600 g. Under those conditions the moisture content is 1.0 10-2kg water/kg wet basis, and the effectiveness ratio is 0.70 kg water/kwh. The results of confirmatory experiments conducted under the optimized conditions show the combined drying have superiority of decrease of energy consumption and increase of handling capacity over the single MWD or HPD.1 IntroductionSilica sand is one of a silicate mineral with properties as hard, anti-friction and less reactive, commonly used as raw material for foundry and construction. The silica sand obtained from mineral dressing processes such as scrubbing, magnetic separation and flotation. Its moisture content is approximately 0.08~0.12 kg water/kg wet basis. The most common methods used for drying are solar drying and hot air drying. But these methods have some shortcomings: for example, the solar drying has longer process time due to low energy yield, [1] hot air drying has low-energy efficiency and a lengthy drying time. [2]Microwave is electromagnetic waves with frequency are 300MHz to 300GHz. The outstanding features of microwave heating are rapidity and selectivity. The water specific inductive capacity of 60~78 is much bigger than common materials, the moisture always quickly absorb electromagnetic wave and rapidly transfer to vapors. So, it can significant reduce the drying time. [3] Heat pumps (HPs) are devices for raising the temperature of low grade heat energy to a more useful level using a relatively small amount of high grade energy."

Jan 1, 2011

By G. D. Sandrock

The science and technology of roan temperature rechargeable metal hydrides began about 1969 with the discoveries that the intermetallic Compounds LaNi5 and TiFe could be, conveniently hydrided and dehydrided at roan temperature and modest H2 pressures. Subsequently, this lead to the development of a broad family of REE-containing AB5 hydrides and numerous applications that make use of the extraordinary H2-absorption and reaction-heat properties of these materials. Some of the applications include H2 storage, compression and separation, as well as heat pumping, heat to mechanical energy conversion and electric energy storage. This paper briefly reviews the fundamental phenomenology of metal hydrides, the history of the use of REE's in rechargeable metal hydrides, the practical engineering properties of these materials and the applications that have evolved around them. The rechargeable nickel metal hydride battery, a new vial alternative to NiCd cells, stands at the forefront of the applications.

Jan 1, 1992

By M. I. Kalashnikova

Results of investigations concerning precipitation of heavy non-ferrous metals from solutions using precipitators based on elemental sulphur and lime with gypsum transfer to a separate product are given.

Jan 1, 2003

By Sui Xue

A process has been developed from laboratory-scale experiments for the aqueous processing of various lead-bearing wastes. The process exploits the limited solubility of lead in sulfate-rich solutions to effectively separate lead from other metals. The lead sulfate is then completely converted to lead carbonate using sodium carbonate and ammonium carbonate. The effectiveness of this conversion was observed to be sensitive to the solution pH and carbonate concentration. The final stage of the process uses low temperature calcination of the lead carbonate to form PbO. Yellow lead oxide (massicot) is readily formed if calcination is conducted at a temperature at or iibove 50G°C, wlule red iead oxide (iitharge) is formed at temperatures near 450°?C. A complete economical analysis of the process will be discussed.

Jan 1, 1996

By K. Mansfield

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluorides along with traces of cyanide. In 1995, Portland Aluminium undertook the investment of AUD$26,400,000 to construct a Research and Development processing facility at Portland, Victoria, Australia, to treat SPL. Extensive research, development and design were carried out over 5 years prior to the investment decision. This study led Portland Aluminium to install an Ausmelt pyrometallurgical furnace to combust and melt the SPL producing a hydrogen fluoride (HF) laden gas, which was cooled and then converted to aluminium fluoride (AlF3). Both the cooling and AIF3 manufacture were processes developed by Portland Aluminium. Many commissioning, equipment reliability and process problems have been encountered that had not been experienced in the trials at Ausmelt or in the developmental process for the treatment of the furnace offgases to form AlF3. Designs based on anticipated process expectations have had to be re-engineered by the SPL team to ensure plant and operational success. In June 2001, the installation of the final major component - a slag granulation process - was completed. This has produced a vitrified (glassy) slag that is expected to have leachability qualities acceptable to the Victorian Environment Protection Authority (EPA) to allow commercial end uses of the slag material to be developed. Today (September 2001), the smelter has successfully used the fluoride product, namely 65- 70% AIF3, in aluminium production and the SPL plant has significantly increased throughput with expectations to be at annual design rates of 12,000 tonne of SPL in early 2002. "The Alcoa Portland SPL Process" has been technically developed and is a proven process for the treatment and recovery of valuable components from SPL materials.

Jan 1, 2002

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By S. V. Cherty

The utilization of natural gas in non-ferrous industries during smelting and refining stages of copper , aluminum, zinc and lead was studied. The total amount of nonelectrical energy consumed in the production of zinc, copper, lead and aluminium, are 96.5% ,93%,92%, and 6 % respectively. It is calculated that 9.45 wt %of air of stoichiometric amount can be substituted by natural gas to the total air input in the nonelectrical energy utilization processes. The results showed that the non electrical energy may be substituted to an amount of 71 % ,52 % ,35 % ,32 % ,and 26% ,in the production of lead, aluminium (plates, foils) copper, aluminium, zinc, respectivelly. Similar calculations are carried out in terms of energy in Btu for the total production of non-ferrous metals in the U.S. It shows that 51.866~106 millions of Btu of nonelectrical energy can be substituted by 54.58~106 cu. ft of natural gas. Finally, the substitution of non electrical energy in terms of equivalent coal energy is discussed. 1t is shown that total non electrical energy is equal to 1.852 million tones of coal .If this 1.852 million tones of coal is replaced by natural gas, a total savings of 22.14 million dollars are achieved. The total or partial substitution of coal by the natural gas in the existing industrial processes and modification of redesigning the processes is discussed.

Jan 1, 1993

Although anion exchange resins are widely used for gold recovery in Russia and the former CIS, accounting for almost 50 percent of gold recovery in that part of the world, the technology has not been adopted in the West, apart from one small operation in South Africa. This situation is likely to change as the gold industry heads into the twenty first century. With gold prices having declined steadily through the 1990's, mining companies are under great pressure to reduce costs and improve gold recovery. Most studies on the use of resins for gold recovery from cyanide solution or pulp have shown that this technology has the ability to achieve both these goals. Resins can also be used to recover and recycle free and complexed cyanide in gold plant tailings, which has the potential to significantly lower operating costs, and latest developments in this area of technology are discussed. Finally, recent studies on thiosulphate leaching of gold have'shown that this process is very well suited to the treatment of carbonaceous, preg-robbing ores from the Carlin trend (Nevada, USA), and elsewhere in the world, because the gold thiosulphate complex does not load on to carbon. Whilst this obviously benefits the leaching process, it means CIP and CIL are ineffective in this situation, and the use of ion-exchange resins for gold recovery from thiosulphate leach solution are discussed.

Jan 1, 1998

By Shengqi Chen

The reduction smelting of nickel laterites produces slag, consisting principally of the chemical components MgO, "FeO", SiO2, and A12O3, and ferro-nickel alloy. Despite the fact that the phase equilibria for the ternary MgO-"FeO"-SiO2 up to 1500°C is well established limited experimental data are available in the MgO-"FeO"-SiO2-Al2O3 system, which is relevant to commercial operation of the process. A methodology has been developed for the experimental investigation of the liquidus temperatures for the multi-component system MgO-"FeO"-SiO2-Al2O3-Cr2O3 in equilibrium with metallic iron. Experiments have been carried out using high temperature equilibration, quenching, followed by electron probe X-ray microanalysis (EPMA). Liquidus temperatures have been determined in the silica primary phase field in the composition ranges directly relevant to the Cerro Matoso S.A. ferro-nickel smelting slag. Liquidus isotherms have been determined for temperatures between 1450 to 1600°C. The study enables the liquidus to be described for a range of MgO/FeO ratios. It was found that liquidus temperatures in the silica primary phase field decrease significantly with the addition of AI2O3. Keywords: Liquidus temperature, ferro-nickel, pyrometallurgy, smelting

Jan 1, 2004

By K. Krishnapisharody

The phenomenon of slag droplet formation under the action of gas-stirring in steel ladles has been analyzed with experiments conducted in a thin-slice room-temperature model using water and mineral oils as the working fluids. Visual and video investigations have been performed on the interface behaviour along with measurements of liquid velocities in both phases, using the Particle Image Velocimetry (PIV) technique. The measured velocity data and observations on the interface break-up establish that the droplet formation results primarily from an instability mechanism at the interface.

Jan 1, 2008

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct- to-Blister process design.

Jan 1, 2003