Search Documents

By J. S. Pitsillos

A new furnace tapping technique involving the simulation of a control valve at the exit to a furnace is being investigated. The purpose of this new tapping technique is to regulate the flowrate of liquid furnace products( slags, metals and mattes). Numerical modelling and experimental work has been carried out on tapping of slags leaving a SIROSMELT reactor and the results found to be in good agreement. Numerical modelling has also enabled prediction of the important industrial conditions for the onset of blockage from the shape of the pressure versus flowrate curves. Slag launder experiments have been carried out and a one-dimensional heat transfer model was used to evaluate the effectiveness of launder covers and different coolants. From the experimental results and mathematical model some launder design guidelines such as inclination angle, covers and coolants have been developed.

Jan 1, 1991

By M. Nilmani, H. Pham

"A mathematical model was developed for the dissolution of particles in gas-stirred liquid baths, linking the hydrodynamic flow field of the bath, the average particle trajectory and liquid-side mass transfer controlled dissolution kinetics. The model was validated by comparison with experimental data for the dissolution rates of urea particles in gas-stirred aqueous CaCl2 solutions measured during this study. The dissolution rates of urea. particles were measured using an image analysis system.The effects of operating conditions on the dissolution rates of urea particles were investigated. It was found that the key operating parameters influencing the utilisation efficiency of particles were the gas flowrate, particle diameter and lance submergence. An optimisation of the operating conditions for the model urea-aqueous CaCl2 system indicated that the utilisation efficiency increased with decreasing gas flowrate and decreasing particle size for a given lance submergence.IntroductionThe utilisation solid reagents in molten baths varies from one process to another, depending upon the rates and mechanisms of the reactions between the particles and melts, as well as the trajectory and residence time of the particles in the melts. Previous studies have not attempted to predict the utilisation efficiency of injected solids by coupling the motion of the particle with its dissolution rate. Instead, the particles have usually been assumed to remain suspended in the bath until completely dissolved, and the mass transfer coefficients were based on the average specific mechanical energy dissipation rates in the bath. Investigations of this nature relevant to the present study have been undertaken by Apelian et al. [1], Brucato et al. [2] and Langberg and Nilmani[3]. The objective of the present study was to develop a mathematical model, incorporating both the reaction kinetics between the particles and liquid and the particle motion simultaneously, to predict the dissolution rates and times of the particles. The mathematical model was validated by comparison with experimental dissolution rates of a cold model analogue system measured using an image analysis technique, and then applied to optimise the operating conditions in the model system."

Jan 1, 1996

By Liya Bochkareva, David Hui, Sergey Eremeev, Maksim Kireitseu, Igor Nedavniy

The principal goal of the present paper is to demonstrate an application of modern software engineering tools for modeling virtual reality and molecular dynamics of novel nanocomposites. The main technical components of presented system are I) software and nanoengineering tools for modeling of virtual reality, molecular dynamic and 30 video images of novel diamcindscontaining nanocomposites and 2) Problem tracking system to be used during modeling of virtual reality. A computational scheme and software, which utilizes neural networks and/or Microsoft. Net technique was developed to predict properties of nano-structured materials and optimization and control of nano-devices. Developed software and IT nanoengineering tools can be used by both industrial and private single users. For commercial companies proposed technology may provide better cost-effective alternative to the existing solutions for nanoengineering and modeling their virtual realit. For private users (students, professors, and engineers) proposed technology and IT tools can provide simple and cost-effective solution for nanoengineering while studying, exploring virtual reality and modeling novel nanostructures and its properties leading to an innovation or a discovery. Because of using novel software and methodologies, users can easily operate proposed technologies by available computers and operating systems (Pentium III or IV). In addition, users can upgrade it by their own self-written models, if necessary. The proposed technologies could replace or be used along with technologies for modeling such as 30 max studio and others.

Jan 1, 2004

By Patrick R. Taylor

Ilmenite concentrate and methane are fed to a non-transferred arc thermal plasma reactor to produce a powder that is primarily TiC and Fe. This material has promising characteristics for powder metallurgy applications. Free energy minimization plots were used to predict the feasibility of the reaction. An estimate of the optimum molar ratio between the ilmenite concentrate and methane was made based on the mineral composition. Argon-helium mixtures were used as plasma gases. The effects of power input level, carrier gas flow rate, powder feeding rate, and methane-ilmenite molar ratio were studied and the behavior of the system characterized. Two different powder injection angles were tried. A mathematical model to describe the temperature profiles in the reactor was formulated and solved. The product has been characterized by x-ray diffraction and atomic absorption. A conversion of 97 % of Ti to TiC was achieved. It was found that minor amounts of titanium oxides, iron carbide and free carbon are also present. TEM and SEM were used to study the morphology.

Jan 1, 1996

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FexAs2O2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS203 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By Takeshi Nagano

Copper pyrometallurgy in Japan has experienced quite fundamental changes in last fifteen years. The severe environmental restriction coupled with increase of energy costs accelerated the development work of the new continuous process in Mitsubishi Metal Corporation. After several years of pilot plant test work the commercial plant was put into operation at Naoshima Smelter in 1974, the design capacity of which was 4,000 tonnes of copper per month. Many modifications and improvements have been incorporated into the process and 7,200 tonnes per month of copper production was achieved in 1983, proving that continuous process was much more economical than conventional process. It is now possible to design and operate the continuous process in wide range of capacity. This paper will review the process and describe the progress of the process in these 10 years. 311

Jan 1, 1985

By P. Chris Pistorius

An example is presented to illustrate the joint effect of local reaction equilibria and mass transfer limitations, for reactions during ladle refining of steel. The example relies on some of the kinetic principles that David Robertson has employed to quantify many metallurgical processes. In calcium treatment of alumina inclusions in aluminum-killed steels, solid CaS forms as an intermediate reaction product. During subsequent reaction, CaS disappears and calcium aluminate forms; at the same time, aluminum and sulfur dissolve in the steel. Kinetic analysis shows that the rate of this reaction is not limited by mass transfer of dissolved aluminum and sulfur away from the reacting inclusions. The reaction rate is likely limited by transport of dissolved calcium. This example also illustrates the use of FactSage macros for kinetic modeling.

Jan 1, 2014

By S. Agatzini-Leonardou

The objective of this work was to prove repeated loading capacities and investigate the selectivity of physically stabilized algal biomass from Spirulina platensis and Chlorella sp. for the removal and recovery of cobalt, nickel and chromium from laterite heap leach liquors. The testwork was carried out on a bench scale in small glass columns and proved that it was possible to immobilize the biomass on the highly porous surface of pumice stone (kissiris). Nickel and cobalt could be removed from pure aqueous solutions of each metal by the immobilized cyanobacterial biomass. Nickel and also cobalt biosorption was sensitive to the initial solution pH. Cobalt recoveries up to 80% were achieved after 5 loading cycles, from low concentration solutions, at pH 6.0. Nickel removal was complete under the same conditions, whereas chromium sorption was ineffective. Desorption of the metal loaded columns was effected by dilute sulfuric acid. The algal species giving the best adsorption capacities for the metals under consideration was selected for further experimental work with real laterite heap leach solution produced by column leaching. A statistical analysis of all obtained results was conducted using the fraction of metal removed as response. The ratio "mass of metal removed to mass of protein contained in the immobilized cells" was determined as well. The described method might be applicable for recovery of cobalt and nickel from diluted laterite heap leach solutions, such as heap wash waters, or for their removal from waste streams of a hydrometallurgical extraction process.

Jan 1, 1997

By Xu-ling Chen, Qian Li, Yong-bin Yang, Zhao Jing, Tao Jiang, Guang-hui Li

"It is generally known that alkali metals are harmful to blast furnace production resulting in aggravating RDI of sinters, abnormal expansion of pellets, deteriorating blast furnace lining, etc. Sinters regarded as dominating burden of blast furnace are determined as the main source of alkali metals. In this study, the removal behavior of potassium and sodium oxides by pre-reduction sintering during the sintering process was studied. The removal ratio ofK20 and Na20 was greatly influenced by coke powder content, carbon species, coke powder adding ways, additive and so on. Under the conditions of carbon rate 12% and 5% dosage of CO supplied in the sintering process, the corresponding removal ratio ofK20, Na20 was 69.00% and 32.79%, and metallization ratio could reach 4.65%. This technology provided a novel process for reducing the content of alkali metals in sinters and dramatically improving the quality of blast furnace burden.IntroductionSinter is the main iron-bearing charge of blast furnace for iron-making in China, making up about 80% of the total burden; therefore, its quality has a significant influence on the quality of pig iron and blast furnace operation. Research and practice of numerous years prove that potassium and sodium coming from ores are brought into blast furnace and upgraded, which is one of the essential reasons that lead to blast furnace nodulation and influences its strength. Currently, effective flow sheet to remove potassium and sodium is weak magnetic separation-intensive magnetic separation-flotation [l], while iron ore concentrate is still ofhigh levels of potassium and sodium. As sintering process is also not effective to remove potassium and sodium, blast furnace in China is of high alkali burden, e.g. it reaches 5.6-6.2kg/tFe in Baotou iron making plant, which is greater than international tolerated level of2.55kgltFe [l]."

Jan 1, 2013

By S. Neogy, M. Gupta, D. Srivastava, V. Kain, S. Roychowdhury, R. C. Prasad, G. K. Dey

"Austenitic stainless steels are an important material of construction for Boiling Water Reactors (BWR). These stainless steels are amenable to strengthening by strain hardening. Various deformation modes at different test temperatures and strain become active. In the present investigation type 304LN stainless steel was used in the annealed and strain hardened condition. Thin foils were prepared from gauge section for transmission electron microscope (TEM) investigation after tensile testing at room temperature and at 288°C. TEM investigation reveals that twinning is the major mode of deformation for the tests done at room temperature while dislocation cross-slip is the major mode of deformation at higher temperature. Stacking faults were also observed to a limited extent. The extent of twinning was much higher for the tests done using the rolled material. The formation of martensite in the stainless steel due to straining was investigated by the analysis of selected area diffraction patterns.IntroductionAustenitic stainless steels (type 300 series) are an important material of construction in Boiling Water Reactors (BWR). These stainless steels cannot be heat treated but can be strengthened by cold working [1]. Nitrogen alloying of these stainless steels result in high strain hardening rates and higher strength without any loss in toughness [1]. Stress Corrosion Cracking (SCC) in BWR of these types of stainless steels have been attributed to surface strain hardening and strain hardening ofregions adjacent to constrained weldment [2].The test temperature [3, 4], prestrain [5] and nitrogen level [5] has been reported to affect the deformation mechanism during tensile testing. Byun et al. [3] have reported the formation of martensite, dislocations, stacking faults and twinning during tensile deformation, the extent of each depending on the test temperature. Strain localisation has been reported to occur during tensile deformation in irradiated stainless steels [ 6]. The behaviour of rolled material during tensile testing is similar to that of irradiated material to a large extent [3]. Austenitic stainless steels are low stacking fault energy (SFE) materials in which various types of microstructures have been reported to form during tensile deformation and the strain is also highly heterogeneous in nature in these stainless steels which aides SCC in BWR environment to a large extent [7]. During cold working of austenitic stainless steels second order twinning has also been reported [8]. Knowledge about the deformation mechanisms operative in the strain hardened austenitic stainless steels during tensile testing at different temperatures is essential to understand the material deformation behavior and the present study aims at enhancing the existing understanding."

Jan 1, 2011

By T. Kimura, H. Ohba

"Much effort has been made to reduce the energy requirement in zinc electrowinning. In order to keep energy consumption low, either to make cell voltage low or current .efficiency high is necessary. Decrease of cell voltage practically depends on how to reduce ohmic resistance in the electrolyte and the anode crust. To realize these, new concept was proposed and the pilot plant has been operated. The space between a cathode and an anode is halved by utilizing the frame insulator. With these frames the anodes and cathodes compose of a unit of electrodes, and this unit is handled by newly designed electrode handling machine (E.H.M.). The process includes lifting up electrodes, expanding the space between a cathode and an anode, cleaning them, stripping the deposited zinc and returning the unit to the cell. As a result, cell voltage is kept as low as calculated and predictable energy reduction has been achieved. IntroductionIn the recent trend of a rapid appreciation of the Japanese yen, Akita Zinc Refinery of Mitsubishi Metal Corporation has been confronted by problems of relatively high operating costs. In order to compete with other overseas zinc refineries, it is necessary to reduce the cost of zinc production, especially the cost of electric power which now accounts for .up to 35 % of the entire cost of production. Three fourth of the electric power used at Akita Zinc Refinery is for the electrolysis. Therefore it is extremely important to reduce the cost of electrolysis.There are two possible measures for solving the problem; one is to use more nighttime electricity taking the advantage of its inexpensive power price, and the other is to reduce electric power consumption.As a part of a rationalization plan carried out in 1986, Akita Zinc Refinery increased the number of operating cells. As a result, when nighttime electricity is used, the silicone rectifier has been able to operate at full capacity. Moreover, by new schemes of ""increase of area for electrodeposition by ralslng the liquid level of electrolyte"" and ""increase of the number of electrodes in each cell"", current density could be lowered and as a result, the electric power consumption has been improved. In order to raise nighttime ratio even higher, installation of an additional rectifier and cells would be required."

Jan 1, 1988

By Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro, Thiago Samarão Motta

This work has as its objective to characterize ceramic bodies formulated with ornamental rock waste and two different clays to produce ceramic paver. Specimens were made by uniaxial press-molding at 20 MPa and then fired at 950 and 1050oC respectively. The determined technological properties were: plasticity, dry bulk density, linear shrinkage, water absorption and flexural rupture strength. The results showed that the type of the clay has strong influence on the properties of interest for heavy clay ceramics. The investigated waste must be incorporated in small amounts to avoid increasing in the porosity of the ceramics.

Jan 1, 2015

By F. -Z. Ji

Carbon injection into metallurgical slag is important in electric arc furnace (EAF) steelmaking for foamy slag practices and in nonferrous slag cleaning operations. The current publication presents kinetic data for coal injection into EAF slag to understand the interaction between injected carbon and metallurgical slag. Coal particles were injected into EAF slag and the kinetics were followed by gas and slag analysis. The results were analyzed, in terms of fundamental rate equations for each possible reaction step, as a function of temperature and slag composition.

Jan 1, 2003

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By Murali Thirukkonda, Rahul Shah, Srinivas Tangrila, Shankar Rachakonda, Jan Kajuch, Arthur Gurson

"High-temperature superconductors have potential for a variety of applications such as power generators, superconducting magnets for mine sweepers or ship propulsion motors, and magnetic levitation transportation systems. Interest in the use of superconducting wires and tapes increased dramatically after the discovery of high-critical-temperature (high-Tc) oxide superconducting compounds, which offer operating temperatures above that of liquid nitrogen. Several techniques have been proposed to produce commercially viable high-Tc oxide based superconducting wires. One of the promising methods involves multi-pass powder-in-tube (PIT) wire drawing followed by rolling and heat treatment. This work focuses on the development of a numerical model to simulate the PIT drawing process for fabrication of long lengths of silver sheathed Bi-2212 superconducting wires. The finite element based model was used to predict densification of the oxide powder, wire drawing forces, and silver sheath thickness during drawing. A cap-type pressure dependent constitutive equation was implemented in the model to simulate the powder behavior. The model incorporated experimentally obtained material data for the silver and powder. Results indicate that powder densification is increased by decreasing the initial silver thickness and increasing the silver strength. Data from wire drawing experiments were used to verify model predictions. IntroductionSuperconducting wires and tapes can be used to carry large dc currents with no measurable loss due to resistivity. When used in superconducting magnets for power generators, motors, levitation devices, magnetic detectors, or energy storage devices, they could potentially result in significantly reduced energy losses. In the past, most prototypes were tested in liquid helium at 4.2K [1]. However, the necessity to provide liquid-helium cooling systems proved to be a serious limitation in commercialization. In 1986 high-critical-temperature (high-Tc) oxide superconductors were discovered [2], which could allow for higher operating temperatures above liquid nitrogen (77 K). Since then, both academia and industry have concentrated their efforts on the development of high-Tc oxide superconducting wires, tapes and coils. As yet, large scale fabrication of long lengths of these wires with the required current carrying capacity and mechanical properties remains an enormous challenge."

Jan 1, 1994

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By Daniel K. Kim

The charge for the copper refinery is a mixture of anodes produced at San Manuel from BHP source concentrate and copper purchased from external sources. Control of unwanted impurities in the tankhouse - is very important and beneficial. Currently available removal/recovery technologies were reviewed for the control of bismuth and antimony levels in the electrolyte. Recent studies have focused on solvent extraction (SX) technology and generated successful results for the removal and subsequent recovery of bismuth and antimony. The SX system employs the reagent, ACORGA SBX-50, in conjunction with a patented high chloride stripping system. The latter enables recycle of the eluant, avoiding the high costs associated with conventional systems, such as regeneration of resin. Concerns over potential transfer of organics and chloride ion to the electrolyte were readily addressed, solved and demonstrated using conventional, established technology. This paper describes the benefits of electrolyte purification, the flexibility afforded by the SX system, the operational practices necessary for maintaining adequate control of bismuth and antimony impurities in the electrorefining environment and possibilities for future development /exploitation of the Zeneca SX system at the San Manuel refinery.

Jan 1, 1998

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By C. S. Ek

As a continuation of previous work, further tests have been carried out to recover silver from the residues obtained in a zinc jarosite process. Selective flotation has been performed with different reagents, and ?cleaning steps have been introduced to upgrade the silver concentrate. Leaching of crude residues, as well as flotation tailings, has been carried out with cyanide and thiourea. Finally, the different beneficiation methods are compared, and the industrial aspects? of their application are reviewed.

Jan 1, 1990