Search Documents

By H Hoogvliet

The Goondicum Crater industrial minerals deposit is located about 30 km east of Monto, Central Queensland, Australia. Early exploration programs in the 1990s found alluvial ilmenite along the banks of the Burnett River. This mineralisation was traced upstream to the Goondicum Crater. The Goondicum Crater is a topographic feature centred on a roughly circular 6 km diameter layered gabbro complex. Significant ilmenite, apatite, titano-magnetite and feldspar mineralisation are present in a weathered horizon up to 25 m thick. After several drilling campaigns in the Crater and subsequent feasibility studies, the project was developed by Monto Minerals Ltd, an ASX listed company, in 2007. However, the project never achieved production performance expectations and ran out of commissioning funds. The company subsequently went into voluntary administration in August 2008.In 2009, the RMM Capital group, of Brisbane, took control of Monto Resources Pty Ltd, and renamed the company Belridge Enterprises Pty Ltd (Belridge). Belridge commissioned a redevelopment study aimed at recommencing mining and processing operations. As part of the redevelopment study the authors planned a drilling campaign, managed a quality control program and developed a block model. This paper describes the drilling program, analytical procedures, quality control procedures and the preparation of the block model.The block model for the resource estimate was created using 1 m high blocks, wireframes defining the main material types, and 2.5 m thick horizontal search ellipsoids with a radial pattern. The deposit was ‘flattened’ prior to modelling. To assist with the economic evaluation of the project, each block in the model was assigned a net dollar value based on economic parameters provided by Belridge, including anticipated revenues and costs. This modelling technique allowed for efficient investigation of various scenarios and was used extensively in the development and optimisation of the project’s financial model. At a zero net value per block, comparable to a break-even cut-off grade of four per cent ilmenite equivalent, the Indicated plus Measured resource is estimated at 51 Mt, averaging 4.1 per cent ilmenite, 1.9 per cent apatite and 2.5 per cent titano-magnetite.

Oct 5, 2011

Separates of all the Technical Publications published in 1931 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions. Copies of these papers have been mailed to those members of the Institute who are registered in the different classes: A-Metal Mining; B-Milling and Concentration; C-Iron and Steel Division; D-Nonferrous Metallurgy; E-Institute of Metals Division; F-Coal Division; G-Petroleum Division; H-Nonmetallic Minerals; I-Mining Geology; K-Mining Administration; L-Geophysical Prospecting. Other members may obtain copies by writing to the Secretary. Additional copies are sold at the rate of I cent per page; minimum charge, 25 cents. Metal Mining Tech-nical Publi- Title Author Meeting TRanb. cation Volume No. and Page* 411-A.43 Ventilation at the Portovelo Mines, J. P. Harmon New York. T31, 83 Ecuador (18) Feb., 1931 425-A.44 Use of Models for the Study of Mining P. B. Bucky New York, Problems (28) Feb., 1931 Milling and Concentration 375-B.32 Ball Mill Studies, I (53) A. W. Fahrenwald New York, H. E. Lee Feb.. 1931 401-B.33 Experimental Flotation of Oxidized H. S. Gieser New York. Silver Ores (9) Feb., 1931 410-B.34 Flotation of Minor Gold in Large-scale E. S. Leaver New York, Copper Concentrators (32) J. A. Woolf Feb., 1931 414-B.35 Effect of Particle Size on Flotation A. M. Gaudin New York, (23) J. 0. Groh Feb., 1931 H. B. Henderson 416-B.36 Ball Mill Studies, 11.—Thermal A. W. Fahrenwald New York. Determinations of Ball Mill Effi- G. W. Hammar Feb., 1931 ciency (13) H. E. Lee W. W. Staley Iron and Steel Division 38QC.59 Open-hearth Steel Process as a Prob- E. R. Jette New York, C31, 80, 111 Iem in Chemical Kinetics (34) Feb., 1931 381-C.60 Thermodynamic Study of the Phasial Yap, Chu-Phay New York. Equi1ibriain the System Iron-car- Feb., 1931 bon (26) 382-(3.61 Influence of Dissolved Carbide on the Yap, Chu-Phay New York, Equilibria of the System Iron-car- Feb., 1931 ban (19) 383-C.62 Research on Blast-furnace Slags. R. S. McCaffery New York, Three papers (88) Co-workers Feb., 1931 384-C.63 Statistical Analysis of Blast-furnace K. S. McCaffery New York, C31, 60, 70 Data (13) R. G. Stephenson Feb., 1931

Jan 1, 1931

Recent U.S. mine disasters identified a need for improved training of miners in escape from mine fires and explosions. Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory (SRL) have designed fire-escape training software for use in a mine-safety training course. The software allows four trainees to work together in a virtual world via a computer network. Trainees responded favorably and showed a marked improvement in locating the proper evacuation routes on subsequent trials. In collaboration with the Pittsburgh Research Laboratory (PRL), a more elaborate fire evacuation scenario is being developed. Further study is needed to confirm that virtual training will translate to improved safety outcomes in the real world. Keywords: virtual reality (VR), safety, training, mining, mine fire evacuation

Jan 1, 2009

By B Taylor

Although the underground mining environment is arguably safer now than at any time in history, as underground mining operations across the globe increase in-depth, magnitude, and complexity, protecting workers from harm becomes increasingly challenging. In deep, stressed, seismic mines the development face is one of the most hazardous work areas. The active face is usually the furthest extent of the underground workings, so ventilation can be difficult to maintain, exposing workers to high temperature and humidity while working on foot and doing manual labour. While mechanisation has made many tasks easier in modern times, the reality of underground mining is that development charge-up workers still spend long periods directly exposed hazards at the face. In 2019, Orica and Epiroc partnered to co-develop the world’s first fully mechanised development charging unit using fully wireless initiation, called Avatel™. Built on Epiroc’s M2 Boomer carrier platform, the system is designed to allow one person to charge a development face from the safety of a fully enclosed cabin, thereby reducing exposure to hazards at the face. The system was prototyped in Europe before entering commercial introduction in 2022. This paper reviews earlier attempts to mechanise underground charge-up and describes the development journey and engineering challenges of building a mechanised development charging machine.

Mar 29, 2023

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By Yun Li

An innovative lead recycling process from scrap lead-acid battery paste is presented. The novelty in the process is avoiding SO2 generation and emission by using reductive sulfur-fixing technique. Iron-bearing secondary wastes produced from metallurgical industry were utilized as sulfur-fixing agent to capture sulfur in the form of FeS (s) instead of generation of SO2 (g). Na2CO3 molten salt was added to the smelting system to speed the reactions and improve valuable metals’ recovery and sulfur-fixation efficiency. Furthermore, this process can simultaneously co-treat various lead and iron-bearing wastes. At the same time, some precious metals, such as Au and Ag, contained in iron-bearing wastes can be recovered. The feasibility and reliability of this process was investigated thermodynamically and experimentally with the help of HSC 9.0 database and XRD and SEM-EDS analysis. A possible reaction mechanism and path in PbSO4–Fe2O3–Na2CO3–C smelting system was also clarified.

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 4, 1985

By A. M. Strachan

Capper Pass & Son Limited Was, until its recent closure, the world's largest producer of tin from secondary materials including solder drosses, non-ferrous smelter flue dusts, tin based metal alloys, residues and slags. Polonium-210, an alpha emitting radionuclide, was present in varying concentrations in some of the numerous feed materials processed by the smelter and refiner. The polonium-210 followed a complex path through the process flowsheet. This paper discusses the behaviour of polonium, both from its arisings in other smelters' process streams and through the entire Capper Pass smelting and refining circuit. The consequential personnel safety and environmental precautions necessarily taken in some areas of the process operation are outlined.

Jan 1, 1992

By Mark S. Sanders

The present study was designed to explore the contribution of organizational climate and management practices to the injury experience in underground coal mines. A cross-lagged panel design was used in which miners from 22 mines completed questionnaires assessing 27 organizational climate, structure, and function dimensions on two occasions, The results strongly support the hypothesis that climate and management practice have casual effect on the incidence of disabling injuries.

Jan 1, 1976

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

By J. F. T. Agapito, L. J. Gilbride, K. Hollberg

Room-and-pillar mining at the Big Island Mine uses narrow, yield (i.e., load transferring) pillars to achieve high resource recovery and productivity. Two flat-lying 3- to 3fi-meter (10- to 11fi-ft) seams are mined. The interburden between the seams is about 10 meters (33 ft) and the cover depth is 250 to 330 meters (820 to 1,080 ft).Most of the mining has been single-seam, but two-seam mining will begin in the near future. Yield pillars minimize stress transfer between the seams. However, it is important that good long-term stability be maintained to prevent subsidence over a large portion of the mine beneath the Green River channel. Three stress issues impacting stability are discussed in this paper: (1) higher-than-gravity vertical pre-mining stresses, (2) time-dependent stress transfer or arching, and (3) stresses induced by strata gas. Although the stress environment and behavior is not fully understood, steps have been taken in mine design and operations to minimize impacts to stability. Stress determinations have been very important to verify analytical predictions used in mine design and in long-term stability assessment.

Jan 1, 2004

By D. W. Bridges, S. R. Borrowman

Thorium and yttrium oxides were recovered from siliceous ores of the Powderhorn , Colo . , area . Processing comprised ( 1 ) acid curing and subsequent ( 2 ) acid baking , ( 3 ) leaching , and ( 4) solvent extraction of thorium , using a primary alkylamine , and yttrium , using di - 2 - ethylhexyl phosphoric acid . About 95 pct of the contained thorium and yttrium was recovered from ore containing 1.2 pct Th02 and 0.5 pct Y₂ 03. The thoria product was 99 pct Tho ; the yttria product was 77 pct Y₂ 03. A 150 - to - 1 concentration ratio was effected on the latter , but some contaminating lanthanon - group oxides remained .

Jan 1, 1964

By Jewel A. Gomes

Keywords: Electrocoagulation, arsenic removal, fuel cell, windmill, energy simulation, combined Fe-Al electrode assembly Arsenic contamination of well-water in different countries has caused signs and symptoms of arsenic poisoning. Although several physicochemical treatments are presently used for the removal of arsenic compounds from drinking water, an electrochemical treatment, electrocoagulation, is a promising processing technology and currently is the most efficient (above 99% removal) and environmentally friendly technique, particularly if combined with alternative energy sources. Wind and fuel cell technologies can be considered the most promising developmental clean power sources. We will discuss new insights into the materials processing mechanisms and show the coupling of electrocoagulation with fuel cells and simulated wind energy sources. Different electrocoagulation plate materials were considered, along varied currents from the fuel cell to produce maximum arsenic removal. Coupling these technologies will remove carcinogenic arsenic from water sources, and will exhibit efficient usage of these energy sources by producing pure water for human and agricultural consumption.

Jan 1, 2005

By Thomas W. Chapman, Shi-Chern Yen, I-Min Lu

"An electric field was applied to a metal-bearing kaolinite specimen to investigate the efficiency of electro-osmosis in removing heavy metals from contaminated soils. The electric field induces a flow of water through the porous medium, called electro-osmosis, which is superimposed on the hydraulic flow. Because the electro-osmotic flow is relatively stronger in smaller pores, it can enhance the displacement of contaminated solution by fluid convection. Furthermore, local changes in pH caused by the electrode reactions can affect adsorption equilibria and the distribution of solutes between the solution and the solid surfaces.The electro-osmosis experiments were conducted by applying either a constant current or a constant voltage across 8-cm inside diameter, 25 to 30-cm long specimens of kaolinite clay with graphite electrodes. Samples of the pore fluid and of the clay were analyzed to determine metal content, pH, and conductivity as functions of time and position. Results show that removal of heavy metals from soil can be accomplished effectively by electrokinetic treatment of sufficient duration. Approximately 95% of the lead was removed after 189 days.IntroductionRemediation of soils contaminated with toxic chemicals is a difficult and expensive task. Washing or leaching are not particularly effective if the contaminate is sequestered in small pores; hydraulic flows of water pass through larger pores leaving the smaller pores relatively untouched. Electro-osmosis appears to be the most promising new technology for removing heavy metals and organic substances from contaminated soils (Segal, 1980; Hamed et al., 1991, Masliyah, 1994).Electro-osmosis is one of several electrokinetic phenomena that occur through the interactions among an electric field, fluid motion, solute adsorption, and the existence of a net charge on a solid-fluid interface (Newman, 1991, Masliyah, 1994). Electro-osmosis refers to the fluid flow in a porous medium that results when an electric field acts on the mobile region of the electrical double layer, the solution-side region of charge separation that exists at the pore walls."

Jan 1, 1996

By Maria Anita de Paula Negreti

Neste trabalho, foram obtidos compósitos poliméricos de Óxido de Grafite (GO) incorporado em Poli(metaclilato de metila) (PMMA). A obtenção do Óxido de Grafite foi realizada pelo método de Hummers modificado. Em seguida foi ainda adicionada uma etapa secundária de tratamento térmico à 1000ºC no GO obtido a fim de expandir as lamelas de grafite e remover os grupos funcionais aderidos durante o ataque ácido do grafite. As cargas obtidas foram caracterizadas com o auxílio das técnicas de Difração de Raios-X (DRX), constatando a expansão das folhas após o tratamento térmico. O estudo comparativo dos compósitos de matriz polimérica com 3 % de concentração de GO antes e após o tratamento térmico foi realizado com o objetivo de entender a contribuição nas propriedades reológicas do polímero com a adição da carga de GO. Os resultados reológicos apresentaram um aumento da viscosidade complexa tanto no ensaio de Varredura de Tempo, quanto no Cisalhamento Oscilatório de Pequenas Amplitudes (COPA).

Aug 16, 2017

By Thomas Domanski

Any type of deep excavation whether for Bored Piling, Diaphragm Walls or Contiguous Bored Piling Walls depends on forming a stable borehole with a defined cross-section to receive safely the permanent materials. In modern construction the excavation depth can reach well the range of 100 m and above. The diameters of the Piles reach often sizes of 2.5 m and bigger. Top casings in Bored Piles (Diaphragm Wall none) are rather short and stability below the casing, need to be secured by stabilization slurry. The boreholes need to be formed through a variety of different materials and stand open for an extended period. Without a safe stable borehole, it is impossible to produce quality products and work cost-efficient. The understanding and proper usage of a suitable slurry is a key element essential for the delivery of Foundation Elements with high quality and within a reasonable budget. The setting of mechanical and rheological parameters in specifications is necessary and helpful, but probably insufficient to embrace and control such a key element in the practical implementation of foundation construction. The proper selection, design, implementation and supervision of slurries on site requires both from Contractors and Engineers to understand how different slurries do function. Only with this knowledge the right decisions in slurry operations can be made. This talk is directed to give some help to both, Contractor’s and Engineer’s, in understanding how different type of slurries do work. (Which ones should be preferred in what kind of soils.) The better knowledge will help the Contractor to control cost and enhance production. The Engineer will be able to assist in arriving at the appropriate technical choices and include in the specifications.

Sep 1, 2022

By F. N. Flynn

- Introductory IN 1882, The Arizona Copper Co. Ltd., acquired producing copper mines at Metcalf and Morenci (locally called Longfellow). Metcalf is situated a distance of 7 miles, and Morenci a distance of 6 miles from the general office of the company at Clifton, Ariz. A reduction works with five blast furnaces was built in the center of the town of Clifton in 1884 and operated until January, 1914. Concentration of oxidized ores was begun in 1890-1891, in a mill built adjoining the smelter, and in October, 1893, a leaching process was started for treating tailings from the oxide mill. A sulphide concentrator with 300 tons capacity was built at Clifton and started treating chalcocite ores in July, 1896. This was the first mill to treat low-grade copper-sulphide ores successfully. Another concentration mill for sulphide ores was erected at Morenci in 1900. The, sulphide mills are now being remodeled to treat ores by concentration and flotation, with a capacity of 4,000 tons at Morenci and 500 tons at Clifton. The leaching plant has not been running since September, 1914. The average yearly production from this company's mines and reduction works from 1885 to date has been: Pounds 10 years ended 1894 6,864,902 10 years ended 1904 20,439,614 10 years ended 1914 : 32,665,905 Part of year 1915, to Sept. 12 30,206,106 4 months of 1916, to June 15,964,840 June, 1916...: ? 4,900,000 Construction on a new smelting plant was started in February, 1912, and finished in February, 1914. In the Transactions, vol. 49, E. Horton Jones published "Unit Construction Costs from the New Smelter of the Arizona Copper Co., Ltd:," which fully describes the construction of this plant, with details of costs.

Jan 9, 1916

By J. P. Harrison, M. Grenon

"This paper summarizes the results of numerical studies on drift stability in moderately jointed rock masses. It investigates the relative pertinence of geomechanical factors such as joint orientation, spacing and stress regime. This is undertaken using a distinct element model and a series of parametric studies. IntroductionIn evaluating the stability of drifts in jointed rock, it is often necessary to compromise by employing models that capture the complexity of the rock mass, but which are still simple enough to allow for their routine implementation. The distinct element method can arguably provide an eloquent method to accomplish this. This paper explores the applicability of the method by means of a parametric study aiming to identify the dominant factors that influence the stability of drifts in moderately jointed rock. To this end a commercially available 2D distinct element numerical model was used. A series of techniques are presented in an effort to quantify the results of any instability predicted by the model.This paper also demonstrates a case study where a 3D joint network model was integrated into the distinct analysis software package. The advantages, as well as the current limitations of this approach, are discussed."

Jan 1, 2001

By L H. G McClean

Environmental, social and governance (ESG) factors have always been important to the minerals industry and is now considered one of our most important opportunities (and risks). Getting it right from the beginning is critical for the minerals industry, and that starts with mineral exploration. Exploration, or the process of investigation of an economic mineral deposit, is generally low impact and short-term. Exploration operations vary in size and scale and often shift priority, focus and location relatively quickly. Australia is a highly regulated jurisdiction with different regulatory systems and requirements in every state and territory. Most mineral exploration is undertaken by junior exploration companies or ‘explorers’. Exploration companies are lean operations with limited staffing and resources, traditionally with no income apart from funds raised or work through partnerships. Funds are tight and administrative investment is minimised so that investment into activity on the ground is maximised. All these variables mean that understanding and implementation of ESG frameworks for an exploration company can be challenging. ESG is a fast-moving sector with currently multiple frameworks and reporting standards. Interest from community and government stakeholders as well as investors and off-take partners has been growing, with mandatory reporting soon to be implemented. The upcoming changes to the JORC Code will ensure that ESG considerations will be a key component of all public reporting. Resources have been developed to support explorers implement, manage and report on ESG considerations. Due to their scale, agility and direct importance of land access and social licence, many explorers are not the ‘cowboys’ (or ‘cowpersons’) of the industry, but industry leaders in ESG. Strong interest and leadership have led to innovative practices and strongly embedded vertical frameworks that directly contribute to social licence to operate.

Sep 1, 2024

The strike of the Canadian asbestos miners entered its seventh month with increasing signs of early termination. Both unions are in the midst of heavy negotiations with management, and an optimistic industry source predicted that work would resume by October 1. Recession recovery in some segments of the asbestos manufacturing industry is being impeded by lack of fibers, CADMIUM - On September 9, St. Joe Minerals Corp. reduced the price of cadmium metal to $2.75 per pound. The producer price bad been uniformly quoted at $3.00 per pound since June 26, 1975. Subsequently, Amax, Inc. and National Zinc Co. reduced their prices to $2.50 per pound. By mid-September all five U.S. cadmium producers were marketing the metal at $2.50 per pound.

Jan 1, 1975