Search Documents

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By Erin Legault Seguin, Mike Rylatt, Curtis Mohns

"With energy costs increasing and ore grades diminishing, the role of pre-concentration in hard rock mining operations has been gaining greater interest. To maximize energy conservation, the pre-concentration process should be conducted at as coarse a crush size as possible while minimizing losses of pay metals. Dense medium separation (DMS) is a robust process that can be conducted at particle sizes as coarse as 300 mm and as fine as 500 µm with high separation efficiency, depending on liberation characteristics of the value minerals. The DMS process involves three steps: feed preparation, dense medium separation, and ferrous-based media recovery. This paper discusses each of these processing steps, but focus will be given to the dense medium separation stage. Various types of DMS equipment are reviewed. Pilot plant campaign case studies conducted at the SGS Lakefield site are presented, which have included a variety of mineral systems such as spodumene, sulphide-bearing gold ores, and complex sulphide ores. These case studies demonstrate that for amenable ores, mass rejection of 20-60% is possible while maintaining recoveries of greater than 90% in most cases.IntroductionPre-concentration is a process of rejecting mass of gangue while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Pre-concentration has been practiced in industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, typically requiring finer grind sizes and higher energy costs."

Jan 1, 2016

By A. D. Davis

Limestone-based material is effective for reducing arsenic concentrations below the current limit of 10 parts per billion for drinking water, typically resulting in final concentrations of about 4 to 6 ppb. However, in laboratory and field testing, further reductions to the 1 ppb range are difficult to achieve with limestone unless other material such as iron is added. The removal mechanism with untreated limestone appears to be the formation of a low-solubility precipitate of hydrated calcium arsenate, in the form of arsenate-apatite. Likely reactions and thermodynamic data indicate a theoretical removal limit of about 2 to 4 ppb for arsenic using raw limestone. Limestone also can reduce concentrations of cadmium and lead below 1 ppb in water, resulting in >99% removal efficiency. Thermodynamic constraints appear to be favorable for reactions involving the formation of otavite during cadmium removal and the formation of hydrocerussite during lead removal.

Feb 27, 2013

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting & Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. "V. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K Thomson, W. G. Derby, and the assistants of the writer, K. 1V.McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the aid of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate anyone method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By A. W. Asman

The problem of balanced design in a belt conveyor has been under constant study. Increased use of this method of transport in recent years has stimulated investigations. Conveyor belt, power transmission and other machinery should be adequate to perform the required service. All components of the belt conveyor should work as an efficient unit moving its load continuously between terminals. As part of a long term research project on belt conveyors, Hewitt-Robins established in 1954 a 2-year grant at Pennsylvania State University. Under terms of the grant, certain fundamental phenomena were to be studied. This work evolved a new concept in belt conveyor power determination based on the principle of belt tension. The Penn State contract furnished the foundation for later more detailed studies. From these most recent investigations, more specific factors were defined. In the final analysis, all of the data collected has been worthwhile in belt conveyor design. Units now operate over long distances at speeds of over 800 fpm. Long high lifts are commonplace. Where vertical or inclined shafts were the rule, belt conveyors receive first consideration. Although belt conveyors have moved forward rapidly, the future will see a tremendous gain in their use. The ideal test belt conveyor would be several thousand feet in length and have a maximum tension of at least 70,000 lb., Also, this conveyor should be horizontai and have a variable feed rate of more than one material. Data from such a field belt conveyor combined with laboratory information would permit accurate analysis. Since this type of conveyor was not available, many field locations were visited: An alternate would have been to erect a closed circuit system in the laboratory. Either method had limitations and the first was selected as having the best possibilities. Manufacturers of conveyor belting and machinery basically have been using the same horsepower formula. As more information became available from field installations, factors in the basic formula were modified. Practically all conveyors are designed today by adding together the horsepowers required to move the empty belt, move the load horizontally, and elevate the load. In selecting size of drive motor, the first two elements are relatively unimportant if the last is large. However, it is the combination of

Jan 1, 1961

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

The Small Pebble Process for Reducing Ball and Power Consumption in Secondary Grinding Ball mills are used widely for secondary grinding. A mixture of ball sizes can be used to optimise grinding efficiency, but the use of balls smaller than about 30 mm in diameter is not normally viable, particularly when alloy steel is required. Preliminary testing of the grinding efficiency of various combinations of 40 mm steel balls and crushed stone in the size range 7 to 25 mm was carried out in a 300 mm diameter mill, which has accurate power measurement.The primary interest was to assess the potential benefit of adding small pebbles (from a primary circuit crusher or mill) to a secondary ball mill, to reduce ball consumption and to improve grinding efficiency. The optimum proportion of pebbles was found to be about 25 per cent by volume. This mixture produced about the same amount of fines as balls alone, but with lower power consumption, due to the lower density of the pebbles. The net result was a 12 per cent saving in power and a 25 per cent saving in ball consumption. The production of fines was partly due to pebble wear. The use of portions of 15 mm balls, (ceramic and steel), was also tested for comparison. A few batch pilot-scale tests were conducted in a 1.2 m diameter, 0.31 m long mill to test the viability of the pebbles at a larger scale. The pilot-scale tests confirmed the reduction in power and that the rate of production of fines was the same as that obtained with balls. The same residence time was used and this implies that pebbles can be added to an existing full-scale ball mill, with no loss in capacity. Samples of secondary mill feed and pebbles were obtained from a copper mine and the steady-state consumption of pebbles was determined by locked-cycle laboratory-scale tests. These tests demonstrated that mill power could be reduced by up 13 per cent and that the consumption of 40 mm balls could be reduced by up to 38 per cent, while maintaining the same throughput and product size. The rate of pebble addition was about 4 per cent of the primary circuit feed rate. Application has been made for patent protection.

Sep 13, 2010

By A. Patri, D. S. Nimaje

Wireless sensor networks and wireless communication systems have become indispensable in underground mines. Wireless sensor networks are being used for better real-time data acquisition from ground monitoring devices, gas sensors, and mining equipment, whereas wireless communication systems are needed for locating and communicating with workers. Conventional methods like wireline communication have proved to be ineffective in the event of mine hazards such as roof falls, fires etc. Before implementation of any wireless system, the variable path loss indices for different workplaces should be determined. This helps in better signal reception and sensor node localization, and also improves the method by which miners carrying the wireless devices are tracked. This paper proposes a novel method for determining the parameters of a suitable radio propagation model, which is illustrated with the results of a practical experiment carried out in an underground coal mine in southern India. The path loss indices, along with other essential parameters for accurate localization, have been determined using the XBee modules and ZigBee protocol at 2.4 GHz frequency.

Jan 1, 2015

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

By W. G. Freeman

It is unlikely, as In the past, improvement in truck efficiency and capacity can fully offset the effects of inflation, fuel costs/shortages and ever increasing haul distances. There-fore, investigations of haulage systems less sensitive to these problems are warranted. Thus, this U.S.B.M. contract research study on alternative continuous haulage systems was prepared. This study identifies the physical, economic and technological parameters in the application of continuous haulage systems with special attention to under pit slope conveyors and skip hoisting systems. The evaluation data was gathered from extensive literature searches. European/North American mine visits, and industry comments. The study concludes that continuous underground haulage is a viable method within the proper geometric configuration.

Jan 1, 1978

Author's Note: Since the paper on "All-Flotation at North Broken Hill Limited" was read and discussed, the metallurgical results obtained have conclusively justified the adoption of the All-Flotation treatment.At present the shipping grades of lead concentrate produced from North mine ore range between 74% and 75% Pb, carrying approximately 43 oz. Ag and 4.5%-5% Zn. The lead recovery in lead concentrate is recording 95%-96% of the lead content of crude ore, and the milling and treatment cost on 6400 tons crude ore perweek of 96 hours has dropped to 6s. 3.6d. per ton on ore. With an increased ore tonnage, and with a new mill, considerable further reduction in costs is certain.New flotation machines, with 30 in. vertical depth of overflow (instead of 42 in. depth), are now being tried for the secondary granular treatment, with advantageous results. The treatment to-day is practically the same as that outlined in the paper, excepting that additional concentrate is returned for retreatment in the existing units.(Signed) A. LOWRY.Mr. T. A. READ: The author states (page 356 of Proceedings, No. 79), "The sulphide ore itself was then comparatively coarsegrained, a fact which permitted ready concentration of the galena contents by means of jigs, tables, vanners, etc."

Jan 1, 1931

By B. J. Moore

This publication contains 14,242 analyses of gas samples from oil and gas wells and natural gas pipelines in 40 States and 24 foreign countries. These gas samples were collected in the period 1917-85 as part of the Bureau of Mines survey for helium occurrences. The gas analyses contained herein were made by several methods over the period covered. Analytical work on samples collected early in the period was done on the Orsat apparatus. The one-cut apparatus and four-cut fractional distillation equipment were added later. A mass spectrometer was acquired in 1949 and used for all gas analyses made after that time. From 1917 to 1978, helium analyses were made on special helium analytical equipment designed and built by the Bureau of Mines Helium Operations Laboratory. In 1978, this apparatus was replaced in the quantitative helium analysis work by a gas chromatograph.

Jan 1, 1987

Willyamite from the type locality, Consols mine, Broken Hill, N.S.W., has been re-examined, and found to consist of zones with widely different Co:Ni ratios. The name willyamite is redefined to include the portion of the (Co, Ni)SbS series with cobalt in excess of nickel. Willyamite is pseudo-cubic, with the three axes equal to within 0·001 A.

Jan 1, 1970

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By T. V. Nguyen

The feedwell performance in gravity thickeners and clarifiers relies on the efficient mixing between solid particles and flocculant to achieve effective flocculation, as well as energy dissipation of the incoming feed stream. A population balance-computational fluid dynamics (PB-CFD) model has been developed and validated to provide new insights into the operation and performance of industrial feedwells. In particular, the PB-CFD model enables the efficacy of the main functions of a feedwell to be investigated for a wide range of feedwell designs and process conditions. This paper describes how PB-CFD was used in the design and development of a new feedwell concept for the flocculation of particles in a solid-liquid stream. The patented feedwell design includes an upwardly converging flow diverter to create two separate compartments for energy dissipation and flocculation. PB-CFD simulations of this simple and easy-to-retrofit feedwell design illustrate a superior performance in terms of flocculation and energy dissipation compared to typical feedwells over a wide range of flow conditions. The potential benefits include reduced flocculant consumption, better de-aeration, greater stability and the ability to cope with a wider variation in volumetric throughput, better flocculation and fines capture, and a more symmetrical discharge that may also offer improved overflow clarity in some applications. The new feedwell design has been installed in a full-scale thickener at an Anglo American Platinum site in South Africa. A number of operational factors complicate this application, but indications are that the new feedwell has led to improvements in stability and underflow properties.

Jan 1, 2012

By Julver Álvarez

El presente trabajo describe el comportamiento estructural y mineralización del estaño-cobre en la mina San Rafael, Puno. En este sentido, las pizarras de la formación Sandia del Ordovisco Superior, por metamorfismo de contacto con el intrusivo, han sido transformadas a hornfels, que junto a las cuarcitas se presentan algunas veces como una cubierta superficial sobre el intrusivo. Asimismo, los intrusivos y las pizarras son favorables para la mineralización de estaño, aunque los cuerpos del mineral son más definidos y persistentes en el intrusivo.

Sep 13, 2001

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By Joseph Gersic

The U.S. Bureau of Mines assessed mineral resources of the BLM Malheur-Jordan Resource Areas (MJRAs) in southeastern Oregon in 1993 and 1994. The study relied heavily on acquiring and analyzing existing data. In order to efficiently handle and analyze a large quantity of data, a minerals information management program, informally called MINFO, was developed as a frontend for three databases created to store basic information gathered during the minerals resource assessment. The MINFO program will also provide the BLM with a method of tracking and updating minerals information in the future because program modules in MINFO allow the addition of new data and the correction of errors, creation of print files, transfer of data to other database formats, exportation of data to other software packages, and creation of AutoCAD script files to be used in conjunction with AutoCAD to produce maps. The report specifically identifies significant past and present mineral exploration and development activities and possible areas of future mineral exploration and development. These areas are informally designated as areas of development interest or ADIs. The report contains a scenario of what mineral development might reasonably occur in the foreseeable future if the BLM does not substantially change its present resource management plan, and it shows the possible socioeconomic impacts of that development. The uncertainty of the political and economic situation makes it extremely challenging for the USBM to accurately predict a reasonably foreseeable development scenario. The reasonably foreseeable development (RFD) scenario developed by the USBM for the BLM indicates short-term RFD of minerals should have a negligible socioeconomic impact, and longer-term RFD of minerals should have a slight socioeconomic impact on the MJRAs. The mining industry is facing a rapidly changing business and regulatory environment in Oregon. Several signal changes have occurred recently, including State regulations that require significant bonding prior to the startup of "chemical process" mining, an initiative by a special interest group to stop all chemical process gold mining within the State, and an opinion by the Oregon Attorney General (AG) banning all forms of placer mining without exemption. In the AG opinion, not even gold panning is allowed, and the prohibition applies to mining claims on Federal lands. The State legislature may amend the statute to allow small scale placer mining to occur, as was allowed under an AG opinion issued in 1982. These and other changes occurring at the local, State, and National levels are making it more challenging for the mining industry to operate in the United States. Several epithermal gold properties in the MJRAs attracted the mining industry's interest. Only the Grassy Mountain Project of Newmont Grassy Mountain Corporation may be developed in the next few years. It is probable that at least two other properties will be developed if Grassy Mountain is successful. Mining companies are waiting to see the effect recently promulgated State mining regulations and more stringent proposed regulations, particularly bonding regulations, may have on Grassy Mountain. Resources of bentonite, diatomite, and zeolite are abundant. The almost Ubiquitous stone, sand and gravel, and semiprecious gemstone resources also were examined. Little environmental or socioeconomic impact is expected from reasonably foreseeable development of these mineral resources.

Jan 1, 1994