Search Documents

The 8 ft by 91/2 ft drive which joined No. 7 Shaft with Browne Shaft on the 1,480 ft level was extended from both ends and met at a point approximately 12,000 ft from No. 7 (2,000 ft from Browne).The surveying required for this 2 1/2 mile haulage drive called for greater accuracy than was obtainable from South Mine standard methods. Procedures and devices from published information were tried and modified as required to suit local conditions. Several new methods were applied and improved as the drive advanced. The control of angular, linear and level measurements was perhaps considerably in excess of the requirements, but this was offset by abnormally large discrepancies resulting from shaft plumbing. The accuracy of the final breakthrough, although not to the standard desired, was sufficient to complete the connection without inconvenience and added cost.INTRODUCTIONThe acquisition of the Browne Shaft leases in January 1962 presented the management of Broken Hill South Limited with the problem of transporting ore from these leases to its mill. It was eventually decided that diesel locomotivehaulage through a 2t mile drive on the 1,480 ft level between the two mines was the best solution. The drive was advanced from both ends after Browne Shaft was deepened by 80 ft to reach the 1,480 ft level horizon. Each end advancedabout 15 ft/day with the miners working three 7 hr shifts. Blasting was restricted to the end of the shift.The survey work involved five shaft plumbings and 78 theodolite stations in a traverse, underground and surface,of more than 5 miles. Because of the exceptional length of the drive, an unusually high degree of reliability was required.The aim was for a maximum error at breakthrough of 1 ft 1 in 30,000, and to secure this, precise methods of linear measurement were necessary. Shaft plumbing in particular posed special difficulties.

Jan 1, 1965

The Significance of Internal Recycle in Froth Flotation

Sep 13, 2010

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By H. A. Bilgin, A. Özgenog?lu, G. Kaçar

In this study, the influences of rock mass properties on the blasting performance in open cast mines are investigated. To this end, discontinuity spacings and discontinuity orientations are measured and full scale blasts with various designs are observed in open cast mines of Aegean Lignite (ELI) and Bursa Lignite (BLI) Establishments belonging to Turkish Coal Enterprises (TKI). For each blast, blasting cost is calculated, and particle size distribution representing the fragmentation of muckpile is determined by means of Split-Desktop software using image processing. 50%(K50), 80%(K80) passing sizes and topsize values are used in the determination of blasting performance according to rock mass properties. The relationships between orientation angle, which is the acute angle between the strikes of slope face and major discontinuity, and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of major discontinuity orientation on fragmentation and blasting cost. Furthermore, the relationships between discontinuity modal spacing (or block size index) and 50%(K50) and 80%(K80) passing sizes and topsize values and also blasting cost are investigated in order to analyse the influences of discontinuity spacing on fragmentation and blasting cost. In this paper, the trends observed in these relationships are discussed and the importance of it in mining is commented. Dans ce travail, Il a été traite les influences des qualites des rocheux massif sur les performances des abattages de l’excavation a ciel ouvert. Dans ce cas, les excavations a ciel ouvert dans les Entreprises Lignite d’Aegean et de Bursa qui appartient a La Societe Charbon de la Turquie; Il a été mesuré le trou du discontinuite et l’orientation du discontinuite et aussi, Il a été observé les abattages qui sont pareilles aux critaires exactes. Pour chaque abattages, Il a été fait le control des expences et la distribution du particle au dimension du pile qui a été deja abatté, a été trouve en utilisant le Software du Split-Desktop. Pour determiner les influences des qualites des rocheux massif sur les performances des abattages, Il a été utilisé K50, K80, et le plus grand valeurs des dimensions. Aussi pour determiner l’influence sur l’orientation du discontinuite majeur de la fragmentation et les expences de l’abattage, Il a été observé les relations entre l’angle de l’orientation ( C’est l’acutage entre la direction du banquette front et la direction du discontinuite majeur ) et les plus grand valeurs des dimensions et les expences de l’abattage. Plus, pour determiner des influences du trou du discontinuite sur l’abattage et la fragmentation; Il a été observé la relation entre l’index de la dimension du block et K50, K80 et les plus grand valeurs des dimensions et aussi les expences de l’abattage. Pour conclure; on peut dire que dans cette presentation, apres la discusssion des sujets consideres ces relations, Il a été souligné l’importances de ces relations dans la domain de la Minéralogie. In dieser Studie wurden die Einflüsse von Gesteinsmasse Eigenschaften auf die Sprengleistung in Tagebau Bergwerken untersucht. Zu diesem Zweck wurden Diskontinuität Abstände und Diskontinuität Orientierungen gemessen und Sprengungen im Originalmaßstab mit verschiedenen Anordnungen in Tagebau Bergwerken der Ägäischen Braunkohle (ELI) und Bursa Braunkohle (BLI) Betrieben, die zu der Türkischen Kohlegesellschaft (TKI) zugehörig sind, beobachtet. Für jede Sprengung wurden die Sprengkosten berechnet und die Teilchengrößenverteilung zur Darstellung der Aufteilung von Haufwerk ist durch Mittel von Teilbelegungssoftware, das Bildverarbeitung verwendet, bestimmt worden. 50% (K50), 80% (K80) durchlaufende Größen und Spitzengröße Werte wurden zur Bestimmung von Sprengleistung geordnet nach Gesteinsmasse Eigenschaften benutzt. Die Beziehungen zwischen Orientierungswinkel, welches der scharfe Winkel zwischen den Streichen der Hangfläche und Hauptdiskontinuität ist, und 50% (K50) und 80% (K80) durchlaufende Größen und Spitzengröße Werte sowie Sprengkosten wurden untersucht, um die Einflüsse von Hauptdiskontinuität Orientierung auf Aufteilung und Sprengkosten zu analysieren. Außerdem, wurden die Beziehungen zwischen Diskontinuität modal

Jan 1, 2003

By S. B. Bealko

In response to recent mining disasters and new mine rescue team legislation, NIOSH researchers conducted meetings across the United States with mine emergency response experts to investigate current needs and issues. Some of the issues include emergency response preparedness, mine rescue contests, real-life training capabilities, and training facilities. Many new teams are being formed that must be trained for mine rescue team competitions as well as be ready to respond to a variety of mine emergencies including a fire or explosion, a massive roof collapse, mine inundations, or vertical shaft rescue situations. Therefore, it is important that these teams are adequately prepared and trained. This paper presents a summary of domestic and international coal mine rescue training facilities and identifies those that provide unique, real-life, and/or state-of-the-art training. Research findings from this report will be used in further NIOSH investigations to improve coal mine rescue training. DISCLAIMER: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2009

By Alastair Grogan, Ron Elliott, Dale MacLean

Blasting for armour stone presents many unique challenges. Often, blasters get themselves into trouble when they assume that they can simply modify a production blast design to produce the required fragmentation size. They bid on the project using typical production blasting costs, and then find that they cannot produce the required fragmentation size and quantity with an acceptable waste factor. This paper outlines industry best practice guidelines for the production of riprap or armour stone. The paper examines the importance of initial geological mapping to determine the average in-situ block size, and the advantages to be gained from working with the geology to maximize production of the required block sizes. The paper also outlines the importance of proper explosives selection as well as blast designs that are unique to the production of riprap. The paper reviews challenges and experiences realized from multiple projects in differing rock types.

By W P. Player

The legislative operating environment, or the mineral regime, that a country has to offer is one of the key determinants that a company wanting to invest in an area takes into account in formulating its investment decision.   The New Zealand Government recognises this and the importance of getting the regime right in order to provide for continuing investment in mineral exploration and mining in New Zealand . In recent years, the Government has given considerable attention to developing legislation which provides for investment to take place; for those making the investments to have a stable, fair and open investment environment with government intervention only when considered absolutely necessary because other approaches are not working; and for the people of New Zealand to know that investment must meet acceptable health and safety standards and have acceptable impact on the environment. Also of key importance is having a clearly defined mining regime which includes rules on how to obtain a permit and rules in respect of ongoing permit compliance, rights to develop a mineral resource and permit conditions (in particular, the royalty regime). In New Zealand , these matters will all be addressed in what are referred to as 'minerals programmes'.   The Crown Minerals Act 1991, which is the legislation governing the allocation and management of permits for Crown owned minerals, requires that the Minister of Energy prepare minerals programmes. Minerals programmes establish the policies, procedures and provisions that the Minister shall follow in exercising his or her functions and powers under the Crown Minerals Act. Minerals programmes set out the principal reasons for and against adopting these policies, procedures and provisions and also restrictions on prospecting, exploration and mining for Crown owned minerals. Essentially minerals programmes define the mining regime for the minerals to which they apply, other than the taxation regime, environmental and health, safety provisions, land access matters and general matters concerning the investment climate.

Jan 1, 1995

By H. C. de Wet

The predevelopment and preparation of a total infrastructure in a deep level mining environment, prior to the shaft system being commissioned has major advantages. This paper intends to indicate these advantages and outline an understanding of the disadvantages. These benefits can be classified in three basic groups: the financial and timing advantages, a knowledge of the ore body and the development of required technology to meet the design parameters. The required technology in many aspects was still to be developed prior to successful application. Stemming from the technological evolution are some secondary advantages which will be described in each of the groups. Safety and health considerations and some practicalities made some of the new technology redundant prior to the actual application. In each case the actual achievements and the anticipated benefits will be indicated to allow the reader to distinguish clearly between planned and actual achieved advantages.

Jan 1, 1997

By J. S. Stachulak, K. A. Mackinnon

This paper deals with specifying and evaluating fans for mine ventilation projects. Topics such as fan and equipment design life, operating points, and operating conditions are discussed. Common operating problems, such as vibration, parallel operation, mechanical failure, erosion, corrosion, and deficient fan performance are covered. Apart from identifying the potential operating problems, likely causes and suggested remedies are given. Fan type, fan accessories, and likely system effects and fan testing are discussed. Suggestions on what should be covered when evaluating different fan options and proposals and suggestions on the verification of supplier claims and guarantees, including cost of operation, the evaluation of initial capital cost, estimate on maintenance costs, and likely replacement expenditure over the life of the fans. In addition, fan reliability, operational flexibility, suggested construction details and fan vendor past history and experience are reviewed.

Jan 1, 2004

[Executive J. V. W. REYNDERS, Chairman WILLIAM H. BASSETT E. DEGOLYER I-I. C. BELLINGER RICHARD PETERS, JR. Finance GEORGE OTIS SMITH, Chairman H. A. GUESS F. JULIUS FOHS Admissions GEORGE D. BARRON, Chairman DAVID LEVINGER P. A. MOSMAN H. K. MASTERS J. A, SINGMASTER Alternates F. G. BREYER C. W. HAMILTON F. E. PIERCE]

Jan 1, 1928

By Juliana Colacioppo

La voladura es un procedimiento que está diseñado para obtener pilas a través de una fragmentación adecuada para el carguío y transporte, aumentando así la productividad de las palas y camiones y asegurando la estabilidad de los taludes y condiciones del piso de los bancos en la mina. Asimismo, el diseño de la voladura debe optimizar las operaciones posteriores tales como chancado, zarandas, clasificación, molienda, flotación y lixiviación. En ese sentido, el presente texto describe la metodología de optimización de procesos de la miina Antamina hasta la oncentradora a través de la recolección de datos de campo, caracterización, modelación matemática y simulación de las operaciones, donde además se utilizan sistemas de rastreamento de minerales y de análisis continuo de imágenes.

Sep 9, 2007

By Joseph M. Kuchta

This Bureau of Mines manual is oriented to the technical needs of an investigation of fire or explosion accidents and includes various practical and theoretical information that is needed in analyzing accidents or evaluating conditions that might lead to an accident. It is applicable to accidents in the chemical, mining, transportation, and other fuel-related industries. Specific procedures for conducting an accident investigation are outlined, and various guidelines are given for developing the fire or explosion evidence. Ignitability, flammability, and physicochemical data are presented for over 500 combustible gases, liquids, and solids; empirical and theoretical expressions are also given for extrapolating the behavior of combustible-oxidant-diluent systems to various environmental conditions. In addition, various data pertinent to damage analysis are summarized to facilitate the task of the investigator in developing plausible accident scenarios.

Jan 1, 1985

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By James P. Ulery

Explosions in U.S. coal mines have caused death and injury to miners and destruction of workings since the first reported explosion in 1810. These explosions are caused when buildups of explosive gas and/or dust in the mine are ignited by the presence of a flame or spark. Methane gas is inherently generated and held by adsorption in coal and is normally liberated during mining. Because this gas is explosive in the range of 5%–15% by volume, fresh air is constantly supplied to the working face to prevent the methane/air mixture from reaching this explosive range. The required amount of ventilation air is based on estimates of gas release under normal conditions. Occasionally, unanticipated and unusually high emissions are encountered, which, despite normal ventilation controls, result in an explosive mixture that a spark from a cutting bit or electrical equipment can easily ignite. Investigations have shown that such emissions are often associated with anomalous geologic features or conditions. Although most operators are aware that certain geologic features may adversely affect productivity, few are aware of their potential as a gas emission hazard. This report presents a historical framework detailing the impact of geologic features on excess gas emissions and resultant mine explosions. It also provides operators with specific information on recognizing and alleviating potential hazards from methane emissions related to these geologic features.2

Jan 4, 2008

By X. Pan

Slag-metal equilibrium experiments were conducted at 1500ºC and1580ºC under 0.03 atm, 0.05 atm and 0.83 atm CO partial pressures using silica and Cr-oxide crucibles. The complex slags belonged toSiO2-CaO-Al2O3-MgO-FeOx-CrOxand the metal phase to the Cr-Fe-C-Si-(S) systems. The carbon saturation of the metal phase was avoided using oxide crucibles and thus the results are pertinent to ferrochromium refining slags and processes. From equilibrium data and thermodynamic calculations, the CrO /(CrO+Cr2O3) ratio in the slag was determined as 0.75, 0.80 and 0.86 under 0.83 atm and 0.05 atm of CO pressure at 1500ºC and 0.03 atm and CO pressure at1580ºC, respectively. The results clearly demonstrated that a higher chromium content of the metal results in higher Cr in the slag, and chromium in slag decreases with increasing SiO2. The results were also sensitive to the crucibles used as these oxide crucibles saturated the slag either with respect to SiO2or Cr-oxides. It was also demonstrated that the relative amount of CrO in the slag was higher when SiO2crucibles were used in accord with thermo-dynamic calculations. Iso-concentration curves for carbon and chromium of the metal phase in equilibrium with the slag were drawn on a pseudo ternary SiO2? (AI2O3+CaO+MgO) ?(Cr2O3+Fe2O3) diagram. The activity coefficients and activities of carbon and chromium of the metal phase were also calculated from the experimental data and available thermodynamics information and were plotted as iso-activity curves in the same pseudo ternary diagram. Keywords: chromium, slag, equilibrium

Jan 1, 2004

By H. K. Lin

Residual cyanide in cyanidation tailings can be detoxified by its oxidation to cyanate, as in the Inco and Degussa processes. However, cyanate, the product of detoxification and other oxidation processes, may be reduced to cyanide in reducing environments, e.g., deepwater discharge of cyanidation tailings. This study shows that the reduc-tion of cyanate to cyanide occurs and that the reduction rate increases with decreasing solution redox potential. Solutions with lower pH favor the reduction rate. No significant difference was observed between the results of tests prepared with distilled water and seawater, and the presence of cyanidation solid tailings does not show an effect on the reduction. Because cyanate can be reduced to toxic cyanide, causing environmental concerns, the deepwater discharges of cyanidation tailings must be handled carefully.

Jan 1, 2008

By W. J. Spat

Political risk is an integral part of the mining business in Northern Andean countries. Peru, Ecuador, Colombia, and Venezuela all have a higher than average political risk compared with other South American countries. Successful operations in such contexts require: 1. Good political risk information; 2. A thoroughgoing political risk management plan; and 3. A strategy to deal with political risk perception on the part of the investing public. Obtaining quality political risk information, developing a political risk management plan, and addressing political risk perception are the foci of this work.

Jan 1, 1999

By Lyda W. Hersloff

An environmental monitoring program was established to assess the baseline of parameters which may be impacted by a research and development hydraulic borehole mining operation. During the baseline program, two aquifers were identified at the borehole site with the overlying sand aquifer being distinct from the ore sand aquifer on the basis of radiological parameters. The direction of flow of groundwater was determined to be north 19° west at a rate of 1.82 feet per year. Tests to determine the effect of backfilling the boreholes indicated that using overburden from the open pit mining operation would not significantly increase the radiological consti¬tuents of the ore sand aquifer. Mining measurements of the- radon flux from the borehole indicated that the actual release rate of 0.035 pCi/sec was several orders of magnitude less than the calculated estimate by the Environmental Protection Agency. Finally, a gamma survey conducted at the site indicated that the terrestrial component of background radiation was consistent with that in areas near uranium deposits. The methodology used as well as the supporting data are given in this report.

Jan 1, 1981

By J. N. Geyer

During the early stages of the mining industry of the United States an apparently inexhaustible supply of high-quality, easily accessible coal made the product cheap and the attendant mining methods wasteful of recoverable coal. Because coal from advance places could be mined with less effort and a large outwit obtained as the entries advanced, much of the coal left in pillars to support the roof was lost. Squeezes often developed in these mined-over areas, or, if pillars were of sufficient size to-prevent squeeze, the roof would be so weakened by long exposure that any pillar recovery was extremely hazardous. As the value of unmined coal increased, a high recovery of the available coal became necessary. Numerous plans were tried during the period that followed, some of the methods proving successful while others were complete failures or only partly successful. As a better knowledge was pained of the roof strata and its behavior, however, pillar mining became more successful and methods suited to special roof conditions were developed.

Jan 1, 1933