Search Documents

By E. Yan

Electrostatic separation has been a mainstay of minerals sands flowsheets for over 50 years. Recent electrostatic developments have shown better conductor/non-conductor separation than technology previously available. Results to date show significantly increased separation efficiency over prior-art high-tension roll electrostatic separator (HTR). These improvements allow greater simplification of MSP circuits by minimizing re-circulating loads. The distinct features of the eForce include: 1) A provision that minimizes the affects of particle size to improve separator performance, 2) an enhancement of the design and arrangement of the static electrode providing a greater attraction force for separating fine conductive particles, and 3) inner roll and outer plate electrode configuration to improve separation efficiency and throughput capacity. Key Words: eForce, Electrostatic, Ion bombardment, HTR, Separation Efficiency, Electrostatic Classifier

Jan 1, 2003

By Elli Nurminen

Keywords: Thermal conductivity of sulphates, flash smelting, heat recovery boiler, flue dust Accretions and build-ups in metallurgical heat recovery boilers decrease the efficiency of the heat transfer and may cause process shut downs. Transient plane source method (Hot Disk) has been applied to measure the thermal conductivities of the Copper Flash Smelting flue dusts. Thermal conductivities of copper, iron and zinc sulphates, and process flue dusts were measured. The results indicate that all the components are effective thermal insulators, having a thermal conductivity of less than 1 W/mK. Decreasing dust layer porosity has an increasing effect on thermal conductivity. Insulating layers on the boiler walls decrease greatly the heat transfer efficiency of the boiler. The gathered information will be used in CFD-modelling of the process, and in the process control.

Jan 1, 2005

By Eung Ha Cho, Wendi Li

Wet desulfurization of Pittsburgh No. 8 coal and Illinois No. 6 coal were conducted with sodium hypochlorite in the laboratory. Pittsburgh No. 8 coal was leached by hypochlorite at high pHs in one step only. The hypochlorite concentration varied from 0.2 to 0.6 molar; sodium hydroxide concentration, from 0.2 to 0.8 molar; and temperature was at the levels of 80 and 90°C. The desulfurization of Illinois No. 6 coal was conducted in three consecutive steps of pretreatment in concentrated ammonia at room temperature, leaching with hypochlorite at room temperature and hydrolysis in sodium hydroxide solution at 90°C. In the leaching step, hypochlorite concentration varied from 0.2 to 0.8 molar. The desulfurization method of Pittsburgh No. 8 coal was found to reduce mainly pyritic sulfur. More than 70% of pyritic sulfur removal was achieved at the optimum conditions of 0.4 molar hypochlorite, 0.4 molar sodium hydroxide and 90°C. The desulfurization method for Illinois No. 6 coal was capable of reducing significant amounts of organic sulfur. The removal of organic sulfur achieved a 37.8% reduction at the optimum operation of leaching at 0.4 molar hypochlorite and room temperature followed by hydrolysis at 0.3 molar sodium hydroxide and 90°C. The chlorine content in the coal produced by the chlorination during leaching was kept below the threshold value of 0.3% at the optimum conditions of the desulfurization method for each coal.

Jan 1, 2005

By B. B. Broms

The high transverse tensile stresses that develop in precast concrete piles during driving have been investigated experimentally from pile load tests and theoretically using the finite element method (FEM). These tensile stresses can be high enough to cause longitudinal splitting of the piles just below the pile cap. Test data and FEM indicated that the maximum transverse tensile stress will increase with increasing thickness of the cover. The maximum tensile stress can be high especially if the pile is eccentrically loaded. The results from the experimental investigation and from FEM are described in the paper as well as a simplified method based on the stress distribution in a concrete cylinder at an indirect tension test.

Jan 1, 2010

The Mining Foundation of the Southwest will host its 24th Annual American Mining Hall of Fame Awards Banquet at the Tucson El Conquistador Golf & Tennis Resort in Tucson, AZ on Saturday, Dec. 9. The Mining Foundation of the Southwest is a non-profit organization whose objectives are public education about the mineral industries. It also recognizes outstanding accomplishments in and contributions to the fields of fuel and mineral resources.

Jan 1, 2006

By M Fewings

This paper casts a light on the sometimes murky world that lies between base metals product æout the gateÆ, and money in the bank. Whether your base metals are leaving the mine as a refined product, or as an ore or concentrate, the generally accepted method of value determination is a London Metal Exchange price, usually measured at some point after the material has left your control. In this paper, the structure and operation, regulation and the reasons for the use of the London Metal Exchange are explored. In addition, the risks and opportunities that terminal market pricing provides to mine managers are explained, with particular reference to hedging. The paper also deals with the structure of the sales contract, including management of shipping issues, agreement of delivered quality, documentation and administrative issues. The selection of counterparties, the role of traders in the market and the growing influence of China and India as base metal consumers and competitors are also addressed.

Jan 1, 2006

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

On the Kinetics and Equilibrium Models for Biosorption of Ni(II) onto a Gram-Positive Bacteria Strain, Rhodococcus opacus, for Environmental Applications The aim of this fundamental study was to evaluate the biosorption of Ni(II) from aqueous solution streams onto a Rhodococcus opacus strain through kinetics and equilibrium isotherms studies. The biosorption of nickel achieved its highest value in a pH around 5. The experimental data evaluation was carried out focusing three two-parameter models, as: Langmuir, Freundlich, Dubinin - Radushkevich. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Freundlich model fits better the nickel biosorption data. Maximum uptake capacity of nickel reached a value around 7.63 mg.g-1 for R. opacus. The biosorption rate was fast and achieved a removal of around 79 per cent of Ni(II) in the first 5 minutes at room temperature (25 ¦ 2¦C). The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). The error analysis established that the pseudo-second order model better fits the data.

Sep 13, 2010

By Deng Ma

In order to obtain the solubility of carbon in vanadium-bearing hot metal, graphite powder is used for the carburization experiments. The other kinds of carburizers, namely low nitrogen carburizer, anthracite and coke are used for carburization of vanadium-bearing hot metal weighing 500 g at temperature of 1450, 1500 and 1550 °C respectively. Carbon increments of low nitrogen carburizer, anthracite and coke fall in descending order. It was found by comprehensive analysis that anthracite is the most cost-effective carburizer among three carburizers. Magnitude of apparent rate constant of carburization reactions is 10−4s−1. It is found that the carburization rate increase with temperature.

Mar 1, 2018

By Sidney Katell

This report covers the period January 1963 through December 1963; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fifth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal--Today and Tomorrow. 9. Coal Utilization. 3/ 10. Cost Engineering. 11. Hydrocarbon Processing and Petroleum Refiner. 12. Industrial and Engineering Chemistry. 13. Nucleonics. 14. Oil and Gas Journal. 15. Petroleum Management. 16. World Oil.

Jan 1, 1964

By Sidney Katell

This report covers the period January 1963 through December 1963; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fifth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from the following sources:

Jan 1, 1964

By N. Jayaraman, V. Srikant, A. Radhakrishna

Addition of a 500 MW unit to the existing units at Ramagundum Thermal Power Station requires blasting of large volumes of rock very close to sensitive installations like Turbo generator, Generator transformer and Power cycle equipments. Levelling of the areas and excavations for footings are, therefore, to be carried out cautiously. The existing sensitive installations should be protected against ground vibrations and flyrock. The paper describes the details of a few of the many blasts carried out successfully wherein the ground vibrations were restricted and flyrock was avoided.

Jan 1, 2003

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By Cawte D. C, Just G. D, Whitchurch K. D

The stringent marketing specifications included in coal contracts mean that coal producers must supply cleaner and more consistent coal than may have been formerly required. Geostatistics has the potential to aid in the accurate estimation of the washability characteristics of coal. A prediction method, the Kriged Service Variable Approach has been developed.A Computer Aided Drafting and Design system has proved useful in the development and application of the approach. The geostatistical approach has been tested against coal geological and borehole data and applications discussed.

Jan 1, 1987

By Will Hunt, Darren Thornton

In March of 2013, an undisclosed gold mine (MINE X), located in the Western United States, performed blast movement monitoring of three blasts occurring in one of two active pits. Blast Movement Monitors (BMMs) were placed in the bench before blasting, and located after the blast to determine vectors of movement. Using blast movement software, ore/waste boundaries were translated. These locations were compared to MINE X’s standard ore translation procedure, which consisted of moving polygon boundaries by 17.5 feet (5.3 m) in the burden direction of the blast hole pattern. This translation amount, identified by MINE X as “average” motion, had been ascertained by performing a previous blast movement study.

Jan 1, 2014

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

Particle Size Measurement of TiO2 Nanoparticles in Non-Aqueous Solvent by Interactive Force Apparatus Under an Electric Field

Sep 13, 2010