Search Documents

Implementation of an Energy Efficient Dry Grinding Technology into an Anglo-American Zinc Beneficiation Process

Sep 13, 2010

By Steve Dillingham

Whenever misfired holes or portions of misfired holes remain after a blast is fired, a hazardous situation exists until the unfired explosive materials have been disposed of properly. Yet, there are so many factors that can contribute to misfires that it is impossible to give blanket instructions on how to handle them. To complicate matters, misfires today are rare due to reliable blasting products. As such, it isn’t very surprising that many blasters have never had to deal with a misf i re condition. While the likelihood of a misfire occurrence is minimal, you should always be pre p a red to handle a misfire should you be involved in such an event. To begin, every blaster and blasting org a n i z a t i o n should develop a misfire policy which contains the company’s safe operating pro c e d u res, emergency contact list, as well as any regulatory compliance re q u i re m e n t s . Tailgate and/or company-wide safety meetings should communicate the company’s contingent misfire pro c ed u res and any special site-specific precautions BEFORE the start of any project.

Jan 1, 2004

By R J. Goldfarb

Reduced intrusion-related gold deposits have become a new, low-grade, large-tonnage exploration target during the last decade. The best recognized examples of such deposits are recognized throughout the Tintina Gold Province of the northern North American Cordillera. Because such examples may have many features in common with orogenic gold deposits, such as anomalous Bi, W and Te, low salinity and CO2-rich ore fluids, and a spatial/temporal association with igneous rocks, confusion and controversy have now become commonplace in classification of many gold deposits formed along convergent margins. The best discriminators of IRGS are likely to be their: +        regional location in deformed shelf sequences on the inboard side of a series of accreted terranes and within terranes that also contain important tin and (or) tungsten deposits; +        local spatial association of gold ores with cupolas and contact aureoles of relatively reduced, alkaline-leaning, and volatile-rich plutons; +        post-deformational timing of gold deposition; +        extremely low sulfide content (commonly <1 vol %) of ores within igneous bodies and the outward zoning, through proximal skarns and to distal base metal-rich veins, from the causative pluton; and +        low grades (<1 g/t Au) of auriferous sheeted vein systems in pluton cupolas.

Jan 1, 2005

By E. O. Abrokwah

Directionally solidified (DS) Rene 80 Superalloy was tested in thermo-mechanical fatigue (TMF) over the temperature range 500-900°C and plastic strain levels from 0.2 to 0.8% using a DSI Gleeble thermal simulator. Thermo-mechanical testing was carried out on the parent material in the conventional solution treated and aged condition (STA), as well as gas tungsten arc welded with an IN-738 filler, followed by solution treatment and ageing. Comparison of the base TMF unwelded alloy with that of the welded and heat treated alloy showed that varying crack initiation mechanisms, notably oxidation either by stress assisted grain boundary oxidation, or associated with grain boundary MC carbides fatigue crack propagation along grain boundaries and creep deformation were operating, leading to different "weakest link" failure initiation points.

Jan 1, 2011

By D. F. Lascelles

D. F. Lascelles (School of Earth Sciences, MacQuarie University, North Ryde, N. S. W., Australia)- The paper contains many misconceptions commonly held by both geologists and soil scientists with regard to soil processes. The analogy between supergene copper enrichment and "nickel laterite" deposits is quite apt and the use of nomenclature from the former in describing supergene nickel deposits is justified. However, care must be exercised with regard to the notable differences in

Jan 1, 1974

By Shawn Collins

BACKGROUND The history of the Pine Point Mine is a rich one. This property once boasted one of the largest and most profitable lead-zinc mines in Canada's long and storied mining history. The Pine Point mine used open pit technology to extract the ore, but they faced several challenges. In addition to logistics problems with haul distances and metal prices, the mine faced the challenge of a large in flow of water from the Great Slave Lake. Eventually, the Pine Point Mine was closed leaving behind a large deposit of lead-zinc ore. Following the closing of the Pint Point Mine, Tamerlane Ventures Inc. acquired this property which includes approximately 70 million tonnes of lead-zinc reserves. The initial phase of this project will concentrate on the R-190 deposit as a test site to prove their new approach for extracting the ore. The R-190 reserve is believed to have approximately 1,014,000 million tonnes of high grade ore varying from 5% to 52% combined lead-zinc. Once the pilot project proves the approach is valid, the process will be repeated in approximately 33 other ore bodies on the property. This paper is written to discuss the design process to determine the most effective means of placing production and service equipment in the same shaft. Currently the design work and the mining scheme is complete, but lead-zinc pricing has prevented Tamerlane Ventures Inc. from moving forward with the project.

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By Paul J. Ehret

With the passage of the Surface Mining Control and Reclamation Act (SMCRA), and the implementation of state permanent programs, underground coal mining operations are for the first time subject to government regulations regarding subsidence. These regulations now and in the future will directly affect the manner in which mining companies mine their coal. Since the promulgation of the original final regulations by OSM, numerous changes in those regulations have been made and many additional changes are pending in the near future. This paper will discuss state and federal approaches to regulating underground coal mines and examine issues surrounding future subsidence regulations.

Jan 1, 1986

By A. E. Lewis

The emphasis of this paper is on the characterization and testing of the slag produced by a secondary lead refinery. This work forms part of a broader investigation aimed at reducing loss of valuable product from the process as well as minimizing the environmental impact of the process wastes. It was this work that led to a critical examination of the standard waste classification tests. Characterization of the slag was carried out using a number of complementary techniques. In the broader context, the slag characterization aided in identifying process deficiencies and thus was a critical tool in suggesting potential for process optimization. For this study, the slag characterization provided a relatively comprehensive picture of the composition and properties of the slag, which facilitated understanding the behaviour of the slag under batch test conditions. On the basis of quantity of hazardous components alone, the slag is hazardous according to South African Acceptable Risk Limits (ARL). However, when both the quantity and the leach potential of the hazardous components is taken into account, standard waste tests carried out by three independent agencies indicate that the slag should not be classified as hazardous according to local regulations. Also, according to United States Environmental Protection Agency (US EPA) limits, which are independent of the quantity of the waste, the slag would not be classified as hazardous. The standard waste tests used by the independent agencies was the Toxicity Characteristic Leach Procedure (TCLP), a test which was developed by the US EPA to classify hazardous wastes. One of the requirements of this batch test is that it should be quick, simple to carry out and that the results should be reproducible. Previously, the applicability of the TCLP test to mineral processing and metallurgical wastes has been challenged on a number of points. Additional testing of the slag was carried out using both the TCLP and the Synthetic Precipitation Leach Procedure (SPLP) recommended by the American National Mining Association as being more appropriate for mineral processing wastes. The particular physical and chemical characteristics of the secondary lead slag highlighted additional limitations of both the TCLP and SPLP tests as standard laboratory batch procedures. Keywords: environmental protection, secondary lead processing, slag, leach testing, TCLP, SPLP, ARL, hazardous waste, batch tests

Jan 1, 2000

By P. D. Chamberlain, R. M. Nadkarni, D. J. Kinneberg

Introduction The relationship between precious metal miners and gold refiners has been uneasy over the years. Reasons for this uneasiness and lack of trust include technical factors, economics of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates, and sponge produced at the mine site are notoriously difficult to sample. A nonrepresentative sample can be the cause of misunderstanding and distrust. Dote, however, is relatively homogeneous and can be correctly sampled and analyzed with greater reliability. Second, the technology and chemistry of fine gold and silver production is complex and quite different from dote production. Most mining companies are content not to be involved with additional processing steps. From the standpoint of process economies, it is easy to see why miners and refiners are separate groups. Mine location is dictated by the natural occurrence of ore bodies. Heavy capital investment requirements for infrastructure in remote locations usually limits companies to produce the first marketable product from a mine. Beyond that point, the economies of scale and large capital investments for refineries generally dictate that the outputs of several mines be combined to feed a single refinery. The refin¬ing process is so complex that refineries are generally built in larger cities with a skilled labor pool. Therefore, only the largest mines can afford to refine their own output. Lastly, there are cultural differences between the miner and the refiner. The miner, particularly the small gold miner, is by definition a risk taker in a risky business. Refineries, on the other hand, have historically been operated under legal or implied monopolies approved by the government. The government is interested in owning gold, either for currency reasons or because many national mints are major users of gold coins. It is not surprising, then, to find that miners may regard refiners as part of an unresponsive government bureaucracy or, worse, as "city slickers." It is easy for the two groups to distrust each other with these different backgrounds. The interface between miner and refiner does exist and affects nearly all precious metal mining companies and most refineries. This paper discusses the technical and economic aspects of the interface. It points out how both parties can improve the relationship. Technical interface Precious metals selectively dissolve to produce a pregnant solution. They are then recovered from solution by zinc precipitation (Merrill-Crowe process) or by absorption onto activated carbon. This is followed by stripping and electrowinning. At this point, the mining company must decide whether to ship precipitates (or sponge) to refiners or to produce a dote. Some factors the company must consider are the ability to sample precipitates, concentrates or sponge, security of storage, and production rates. An important factor is the incremental cost (capital and operating) of converting precipitates or sponge into dote at the mine. Generally, mines prefer to melt precipitates or sponge to dote to avoid prob¬lems associated with sampling them. There are three types of fur¬naces used by mining operators to melt precipitates to dote. The first and most widely used is a sil¬icon carbide crucible heated ex¬ternally with a gaseous liquid fuel. The crucible is easy to use and slag can be skimmed before pouring dote. This simple system is capable of handling 1 t/a (32,000 oz per year) gold. It could cost as little as $20,000. More complex systems could cost up to $200,000. The second type of furnace is the gas- or propane-fired rever¬beratory furnace. This is usually used only by large-scale opera¬tors in the silver business. Precip¬itates in reverberatory furnaces come in direct contact with the flame. The large volumes of flue gas can carry significant amounts of dust and fume that must be re¬moved from the gas before dis¬charging it to the atmosphere. In the days when the Rand re¬finery in South Africa used reverberatory furnaces, the silver leaving the furnace in the form of vapor and fume was estimated at 2.2% of the total silver charged to the furnace. The gold in the gases was about 0.03% of the gold charged. Most of this silver and gold was recovered in the exhaust gas scrubber system. These scrub¬ber systems can be more costly than the furnace itself.

Jan 10, 1986

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019

By R Tom Watts

The blasting industry has changed more in the last five years than in any period to date. The equipment utilized to load boreholes has changed in response to more precise blasting products and programs, and the need to maintain tighter control over product formulations produced by bulk loading equipment. Tread Corporation has built over 1,300 heavy ANFO type bulk loading units currently operating in over 40 countries worldwide. These units have been designed to meet almost every possible loading scenario but there are always new situations that require special designs and configurations to meet the challenge. The focus of this presentation is to make you aware of the process that should be used to determine the equipment best suited for your application. We will discuss loading cycle times, delivery rates, multiple product mixing capability, capacities, manpower utilization, regulatory compliance, and where and when to use automation in the loading process. We will also discuss the suitability of chassis with regard to ground pressure, turning radius, terrain, weather conditions as well as highway suitability. The US Bridge Law as well as laws that cover the concept of axle loading and spacing will be covered. Through new computer aided design and modular design capabilities, you can now have almost any configuration required to meet your bulk loading objectives. We will also review the range of equipment currently available in the market place and discuss tradeoffs between price, capacity, and complexity.

Jan 1, 2000

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

By G. Coetzer

During galena flotation of Rosh Pinah milled material, metal ions and salts contents of various water resources (deionized, simulated circulated, lead concentrate thickener, lead tailing thickener and borehole) influenced mineral recoveries, upgrade ratios, selectivities, froth stability and flotation kinetics. The various water resources employed during galena flotation caused activation, depression or selectivity effects on minerals due to the presence of different ions in solution. Metal ions in these water resources were adsorbed by the ore, whilst ions associated with gangue minerals (dolomite and quartz) were released into the flotation pulp. Lead concentrate thickener water caused depression of sphalerite and pyrite, increased fast floating fractions for silver, copper minerals, sphalerite and quartz (unwanted), and improved slow floating rate selectivity against pyrite and sphalerite. Lead tailing thickener water enhanced sphalerite recovery during galena flotation (unwanted), and increased fast floating fractions of pyrite. Western borehole water did not affect galena recovery, but sphalerite and pyrite recoveries were unacceptably too high. Ions from copper, lead, and zinc salts tended to release high amounts of ions, such as calcium, magnesium, silicon, and manganese from gangue minerals (dolomite and quartz) during milling. During galena flotation, lead ions depressed sphalerite, pyrite and dolomite at a lead concentration of 400 ppm, but sphalerite was activated at a concentration of 800 ppm. Sphalerite was activated with copper ions (89% recovery, 2.09 upgrade ratio) and depressed with zinc ions (maximum recovery of 25%). This corresponds with findings in previous investigations. Dolomite and quartz were slightly activated with zinc ions. No evidence was found that lead and copper ions activated any gangue minerals during galena flotation. Keywords: galena, water resources, metal ions, activation, depression, selectivity.

Jan 1, 2003

By Travis Q. Lyday

Mineral production in Fiji, a group of 322 volcanic islands and atolls of Melanesia in the southern Pacific Ocean, continued to be dominated by gold. However, the Fijian mineral sector remained a minor factor as a source of export earnings, Government revenues, and employment, generating only 1% of the gross domestic product (GDP), estimated as $1.2 billion.2 The largest and most important mining operation was the Vatukoula gold mine on the north side of Viti Levu, the main island. The Vatukoula Mine has been in prduction since 1932, producing about 3.8 million troy ounces of gold and 1.3 million troy ounces of silver to date. In April 1983, the large Australian mining firm, Western Mining Corp. (WMC), assumed operation of the mine in a joint venture with Emperor Gold Mining Co. Ltd., which operated the mine previously. The WMC takeover of the mine management was expected to bring in additional capital and technological expertise in order to modernize operations, increasing both efficiency and output. During the year, rate of recovery was only about 75% of the gold contained in the ore and only 40% of the contained silver. Mining at the Vatukoula Mine was done using bath opencut and underground methods, with about 60% of the ore mined attributed to the underground operations.

Jan 1, 1985

Estimating Breakage of Fine Ore Particles by Media in a Small Ball Mill Using DEM

Sep 13, 2010

This report covers the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. Significant conclusions that will be of benefit to the entire mining industry are the following: It appears from the study that the productivity of the slushing equipment itself cannot be substantially increased using the existing technology; the unsafe situations associated with slushers can be improved by better anchoring practices, by providing better work station layout that incorporates improved clearances and protected walkways over the ore pocket, by lighting the slusher drift, and by improved operator training; improved technology needs to be applied to the movement of broken ore in the stopes; and slushers will continue to be used in the mining industry in certain spedial and unique situations outlined in the report.

Jan 1, 1974

By David Meadows, John Starkey

"As part of the ongoing project development for the Tenke Fungurume Copper-Cobalt Project in the Democratic Republic of Congo, Phelps Dodge Corporation has examined methodologies for determining the size of grinding mills to support a 7000 mtpd operation. Six samples were tested by Hazen Research, Inc. (HRI) to obtain the JK parameters using the JK Drop Weight Test, standard Bond crushing, and rod mill work indices, abrasion indices and by Dawson for Bond Ball Mill Work Index tests using crushed feed, and Standard Autogenous Grinding Design (SAGDesign) Tests, patented by Outokumpu. (See reference 8 below).The comparison of these results gives context to how the various measurements relate to each other and how they can be used to obtain an accurate design for the grinding mills required for the Tenke Project. This is the first published direct comparison between JK Drop Weight, standard bond work indices, and SAGDesign test results. The SAGDesign test includes a SAG test followed by a Bond BM Wi test done on SAG ground material.INTRODUCTIONAfter the presentation of the paper “SAGDesign Testing – What It Is and Why It Works” at the recently concluded SAG 2006 Conference in Vancouver, a question was asked about how SAGDesign ore hardness measurements compared with other comminution tests, specifically the JK Drop Weight Test and the parameters that are derived from such testing. At that time it was noted that a paper was being prepared for the CMP Conference in January to show how various ore hardness measurements compare with each other when done on the same samples.This paper will therefore present the first such comparison using test results from the Phelps Dodge Tenke Fungurume Project where six composite samples were examined by the tests noted below. A seventh sample was tested at Dawson but not at other labs. The tests were done at four different laboratories listed below and included the tests shown."

Jan 1, 2007

By A J. Minns

This paper addresses the question: how can the minerals industry remain viable; viable in the sense that we are able to access land for exploration and discovery, we are able to develop and operate mines (and processing plants) safely and profitably and we are able to close operations in a responsible manner, so that modified landscapes are restored to acceptable community standards?Many of the answers to this question can be addressed through the theme of this conference û that of eco-efficiency. The eco-efficiency concept is very useful, since it does help to translate principles of sustainability into business value at the operational level. To provide some context to how this can be achieved, the paper discusses what is happening at the international level, outlines some key industry initiatives within Australia and then discusses what work is being done within companies.

Jan 1, 2004