Search Documents

By J D. St George

In this paper a laboratory investigation into the effect of confining stress, water content and gas desorption on coal permeability is presented. Of major significance is the effect of coal permeability on outburst occurrence and methane production, which is influenced by changes in stress. Test results indicated that the shrinkage of the coal matrix associated with desorption is greater than the coal matrix compressibility which will cause a reduction in the effective stress, hence increasing coal permeability.

Jan 1, 1998

By J. van Lookeren

In the case of a reservoir where the oil underlies a large gas cap and overlies bottom water, production can be inzproved considerably if wells are perforated below the water-oil contact rather than opposite the oil-bearing section. The theoretical arguments for this improvement, which in some cases may be tenfold, are supported by experimental evidence. INTRODUCTION Reservoirs frequently consist of one sand body containing an oil layer underlying a thick, gas-bearing section and overlying bottom water (Fig. 1). Wells in such reservoirs are customarily opened up opposite the oil-bearing interval or, rather, opposite the lower part of this interval (Fig. 2). More often than not, it is inefficient or prohibited to blow off large quantities of gas with the oil. This im-psses a severe limitation on the drawdown, which results in low oil-production rates. Because of the small difference in specific gravity between oil and water, the latter will easily cone upwards, so that the production of water together with the oil is not prevented by this completion method. In such a situation wells should be opened deeper, in the originally water-bearing zone. The gas can be shut off by not perforating over the upper part of the interval (Fig. 3) or by a tubing hung close to the bottom of the interval (Fig. 4). Initially much water will be produced, but when steady-state conditions have been established (as depicted in Figs. 3 and 4) larger drawdowns are permissible than in a conventionally completed well, and correspondingly higher oil-production rates will result. Water cuts are only slightly higher because of the small effect of gravity on the water-oil flow distribution. CALCULATIONS The ratio of improvement has been estimated by means of approximate calculations. The completion depicted in Fig. 4 is the most convenient basis for these calculations. By postulating that vertical flow gradients can be disregarded, the Appendix shows that the well-known Dupuit formula can be obtained except for some complication due to the presence of two fluids rather than one. The Appendix makes the reasonable assumption that, for suitable boundary conditions, the oil layer occupies a constant fraction of the total fluid height throughout the reservoir. The oil- and water-production rates can thus be related to the liquid levels in the borehole as follows:

Jan 1, 1966

By W. F. Watts

The U.S. Bureau of Mines has conducted research on methods to reduce and to measure diesel particulate matter (DPM) aerosols in underground coal mines. One objective of this report is to present findings from an investigation of the DPM reductions obtained by an engine-mounted integrated control system consisting of a dry system (DS) and a diesel particulate filter (DPF). Another objective is to present results from the usc of a size selective personal sampler to measure DPM concentrations in an underground coal mine. Bureau laboratory tests of the integrated dry system and diesel particulate filter (DS-DPF) have shown that DPM emissions can be reduced up to 97 pet with little change in gaseous emission concentrations. The DS-DPF is undergoing certification tests conducted by the Mine Safety and Health Administration (MSHA). Subsequent to passing all safety requirements, it will be tested in an underground coal mine. A baseline survey of DPM concentrations and aerosol size distributions in a cooperating mine was completed in August 1988. A prototype DPM personal sampler was tested during this survey. Based on results from this test, an improved unit has been developed. This unit is scheduled for extensive field testing by MSHA in 1989.

Jan 1, 1989

By F. Peer

This Technical Note was presented as a poster at the Western Cape Mineral Processing Symposium held in August 2001 The cleaning of fine coal (-1000 µm) in today?s coal preparation plants is an economically important factor. Coals with high ash contents are, in general, commercially undesirable. Current well-known techniques for treating fine coal include froth flotation and spirals. The primary critical factor with regards to spirals is the efficiency of the process whereas that of flotation, is the cost of there agents used. Research into enhanced gravity separation techniques has resulted in several commercially available enhanced gravity separators. This project was based on a preliminary investigation into the feasibility of one such separator, to effectively treat fine (-500 µm) coal. Experimental variables included particle size and speed of rotation of the said instrument. The performance of the separator was compared to the results obtained from liquid density separations done for the two coal fractions evaluated. From the results obtained in this preliminary study it appears that the piece of equipment investigated does not measure up to expectations. Recommendations for further investigation include the evaluation of the instrument on other South African coals to obtain conclusive results.

Jan 1, 2002

By Esperidiana A. B. Moura, Elizabeth Carvalho L. Cardoso, Glauson Aparecido F. Machado, René R. Oliveira

Plastics global annual production exceeds 250 million tons and more than 40% of the total plastic production is used as packaging materials. In recent years polymeric materials derived from biomass have received great attention due to scarce petroleum resources and environmental concerns. PLA is one of the most extensively studied bio-based and bio-compostable aliphatic polyesters; nevertheless, high brittleness and low toughness limits its application. Blending PLA with PBAT (Poly(butylene adipate-co-terephthalate)), an aliphatic-aromatic copolyester, was the solution found due to its high toughness and biodegradability. Differences between PLA and PBAT solubility parameter values lead to the formation of immiscible blends as well as reduction in their mechanical performance besides a poor morphology; so, 5% of pre-irradiated PLA and a previous compatibilized PLA/PBAT (EcovioTM) were added to PLA/PBAT blends in order to improve miscibility phases. Investigations were accomplished on phase morphology (SEM), mechanical properties, thermal behavior and X-ray diffractions (XRD).

Mar 1, 2017

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By Ian R. Muirhead

Over the past year or so, a number of mining companies have been meeting to examine the role of research in surface mining and, in particular, how to establish a collaborative research effort for the surface mining industry. A review has been completed which has identified the topics that are of interest to the surface mining companies for undertaking collaborative research. This has identified key subject areas such as Operations & Equipment; Maintenance; Environment & Reclamation; and Stability. Specific research projects for the initial research effort have been selected which include Wireless Data Communications, Analysis and Management; Application of GPS in Mining; and Tires for Heavy Haulers. In addition, attention has also been focussed on finding a suitable low cost, but effective, organization to coordinate and manage the collaborative research. The recently formed CONRAD Organization (Canadian Oilsands Network for Research and Development) appears to be a suitable candidate and discussions are ongoing with that group. This paper provides a summary of the review of surface mining research needs and of the status of the establishment of a collaborative research body for surface mining.

Jan 1, 1996

By J. Harrison Daniel

Were the legislators and politicians responsible for the closing of the U.S. Department of the Interior?s Bureau of Mines (Bureau) in March 1996 fully aware of what they were doing? Throughout the United States? history, the domestic mining and minerals industry has been largely responsible for the nation?s growth and prosperity that had made it a world leader. The mining and minerals industry made it possible for the young nation to catch up with Europe during the Industrial Revolution, played an essential role leading to victories in World Wars I and II and was a core ingredient for continued economic growth. For a number of decades, America?s import dependency on non-fuel mineral materials has continued to increase. (USGS Mineral Commodity Summaries). Developing domestic resources to meet current and future demands ? particularly those resources considered to be of strategic and critical value to national security ? is necessary. Federal involvement is required since many of these resources are located on public lands. Another reason for federal involvement is that the success of the industry depends on long-range research programs and advances that may take up to 25 years to become commercially available. This situation requires federal partnership to coordinate the programs necessary to collectively involve the industry, individual mining companies and colleges and universities. So, how was it possible to close a federal agency that had contributed so much to the nation?s welfare in a mandated 90-day period, with more than 1,200 employees losing their jobs?

Jan 4, 2010

By Y. D. Lee, J. H. Park, D. S. Kim, H. S. Song

The viscosities and the infrared spectra of the CaO-SiO2-MgO-CaF2(or Al2O3) slags were measured to enhance our understanding of the interrelationship among the thermophysical property, microscopic structure, and chemical thermodynamics of molten slags. The structural role of CaF2and Al2O3in the calcium silicate melts can be explained by a change of the degree of polymerization (DOP). The effect of CaF2on the viscous flow of molten slags is based on a decrease in the DOP by F-as well as by O2-ions and this was confirmed by the infrared (IR)spectra of the quenched slags. The effect of Al2O3on viscosity increase can be understood from an increase in the DOP by the incorporation of the [AlO4]-tetrahedra into the [SiO4]-tetrahedral units and this was also confirmed by the IR spectra. An amphoteric behaviour of Al2O3in the aluminosilicate melts could be correlated to the effect of ionic species of alumina, that is [AlO4]-tetrahedra and [AlO6]-octahedra, on the stability of silicate polyanions by taking the activity coefficients of slag components into account. Keywords: viscosity; infrared spectra; degree of polymerization; amphoteric behaviour; stability; activity coefficient

Jan 1, 2004

The area (330 sq. miles) shown on the map of the Brocks Creek District (Fig. 1), was mapped by the Northern Territory geological party of the Aerial, Geological and Geophysical Survey of Northern Australia. This work was done in two stages:-(i) In 1935, an area of 30 sq. miles around the Golden Dyke mine was mapped by P. S. Hossfeld, Senior Geologist, and A. H. Voisey, Assistant Geologist. The results were described in a detailed report (10).(ii) In 1939, an area of 300 sq. miles in the Brocks Creek district was mapped by C. J. Sullivan (Senior Assistant Geologist), and V. M. Cottle and S. N. Kiek (Assistant Geologists) under the general supervision of P. S. Hossfeld (Senior Geologist).An outline structural map, together with some geological notes was published (1), but that map does not show the amphibolites, and the relationship between ore occurrence and general geology is not emphasised. The publication of the detailed maps and reportwas postponed indefinitely as a result of war. The original mapping was based on air photographs with a scale of approximately 1 in. to 1,200 ft., and all detail which could be shown at that scale was mapped. Features recorded included rock types, details of structure, mineralisation, and surface workings, creeks and soil boundaries. Underground mapping was also carried out. The present map is much simplified from the original, but it is hoped that it shows sufficient information to reveal close relationship between structure, granite, sills of amphibolite and gold occurrence. About 50 per cent. of the area is covered by deep soil or alluvium, and in these portions the geology of the underlying rocks was not determined with accuracy, though in many places strike trends could be deduced from air photographs.Because the A.G. & G.S.N.A. had published the geological notes and map referred to above, and because the publication of the detailed report and maps is still postponed indefinitely, approval has been given by the Bureau of Mineral Resources, Geology and Geophysics (which took over the affairs of the A.G. & G.S.N.A. at the termination of its operations) to the preparation of the present paper so that information would be available to the public.The views expressed in this report are those of author. The results of the investigation suggest that in areas where granites are predominantly concordant with bedding, ore deposits may be found at approximately the same stratigraphic horizon. It is thus important to correlate beds even though their relationship may have been obscured by faulting and folding.

Jan 1, 1950

By Ernest W. Hilton

The purpose of this investigation was to assess the environmental impact of the surface mining methods currently used in the steep-sloped areas of Central Appalachia: southern West Virginia, eastern Kentucky, southwestern Virginia and northeastern Tennessee. Comparisons are made between mountaintop/cross ridge mining, contour strip, augering and an innovative method surface shortwall mining which was attempted at Julian, West Virginia. Included in this final report are a discussion and analysis of current Appalachian production, reserves, and the extent of land affected on a county- by-county basis. Additionally, the seams within the steep sloped region have been assessed according to minimal standards of thickness, surrounding lithology, and areal extent to determine their amenability to surface shortwall mining. These seams have been tabulated with their ash, sulfur, and BTU content on a county-by county basis. Only minimal statements are made concerning quantity because of the narrow set of conditions required by the shortwall method. Other sections deal with the possible technical failings of an operational surface shortwall system based on field studies at shortwall operations, discussions with people experienced with shortwalls and research into ground control problems at sites where short- and longwall operations have been monitored. A final section details proposed additional research directions which the Bureau might take in the future.

Jan 1, 1979

By Chao Li, Lim Hongxu, Yuyue Wang, Xie Yang

"A intergrated process of sulfuric acid leaching, sodium chloride leaching, lead chloride crystallization, lead hydroxide synthesis and roasting was carried out for the recovery of lead, cadmium, copper and zinc from lead smelting dust containing various metals. The results showed that the separation of cadmium, zinc and copper from dust could be obtained after sulfuric acid leaching and corresponding leaching rate were 92.12%, 90.25% and 88.26% respectively. The subsequent sodium chloride leaching carried out for lead with optimized parameters as: sodium chloride concentration 250g/L, leaching temperature 90°C, leaching time 2h, pulp density 33g/L, 0.12mol/L CaCh; The lead compounds crystallization rate reached 86.67%, and then transferred into mPbO·nH2O, the product of 98.66% ß-PbO could be obtained through roasting under 502°C. In the end, a feasible method of ß-PbO preparation from lead containing dust was put forward.IntroductionThe pyro-metallurgy flue dust from smelting lead activities are often stockpiled and pose potential environmental risks due to the heavy toxic elements, such as Pb, Cd, As, Cu, Cl, and Zn which are contained in the dust. With the rapid depletion of rich ore resources in recent years, it has become increasingly more financially attractive to recover valuable metals from previously stockpiled dust, while simultaneously reducing the potential of environmental pollution from toxic elements contained in the dust. Nowadays, pyro-metallurgical and hydrometallurgical routes or both combined methods can be developed to treat secondary materials such as lead ash, leach residues etc. By comparison the hydrometallurgical processes are often considered more eco-friendly.Some chloride leaching processes for recovering lead have been employed using either NaCl, or MgC2 and CaCl2, or FeCl3 [1] The effectiveness of the brine leaching method is based on the formation of complex metal chlorides in concentrated chloride solutions [2] Similarly, Other metals such as zinc, cadmium and copper contained in the flue dust are often treated with sulfuric acid, hydrochloric acid, ammonium solution and sodium hydroxide etc. as lixiviants [3] The metals from leach solutions thus has been obtained by precipitation, ion exchange, solvent extraction or replacement [4]"

Jan 1, 2014

By G Senanayake, K Hazarika

The demand for iron-ore is ever increasing with the industry directly employing 60 500 people in a range of highly skilled roles in Australia. In the year 2019, the global iron-ore production was 2.85 billion tonnes. It is estimated that each tonne of beneficiated iron ore produces 400 kg of tailings. The IOTs are fine, dense and stable crystalline material mainly composed of iron oxides, alumina and silica. The current and most applied method of iron-ore tailings (IOTs) disposal is using subaqueous disposal of tailings in dams. The footprint generated by a tailings dam is massive and requires constant monitoring due to the possibility of a failure making the operation and maintenance of tailings dam extremely expensive. This review briefly discusses the known causes of tailings dam failures, their impact to the environment and day-to-day human life and potential applications of IOTs. The increase in water content enhances the pressure on dam walls. This in turn increases the liquefaction potential of the tailings and reduces the overall strength of the dam making it more vulnerable to failure. Potential applications of IOTs are in paints, aggregates in construction materials and bricks. The reuse of IOTs reduce waste and generates further revenue facilitating a path towards a sustainable future for the industry.

Nov 8, 2021

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

The low production rates associated with the underground metal mining industry have received considerable attention during the last decade. A number of significant technological advancements, in the form of new equipment, have taken place to improve the economics of ore production. Unfortunately, an extremely important factor in the equation -- the operator protection and safety -- continues to receive a low priority. The underground metal mining industry has one of the poorest industrial safety records in the United States. Equipment operators are constantly being placed in hazardous situations. Even one fatality is one too many. All of us bear the responsibility to eliminate it. This project is one of the important steps currently being undertaken by the U.S. Bureau of Mines to improve the operational safety of seven major pieces of ore handling equipment commonly used in underground metal and non-metal mines. The objectives of this study are; (a) to identify the existing hazards associated with the operation of the specific equipment, and (b) to recommend practical solutions that will minimize these hazards and reduce operator injuries. These recommendations are to be in the areas of equipment design improvements, additional operator protection and warning devices, equipment operating procedures and any modifications to the existing safety regulations.

Jan 1, 1975

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

By R. L. Pienaar

Paper written on project work carried out in partial fulfilment of B Eng (Min. Eng.) degree A study was conducted to investigated and compare the feasibility of two single level extraction layouts for an intact part of theorebody of the De Beers diamond mine, Koffiefontein. Two layouts were chosen and the tonnage profile, development schedule and production ring blast layouts were calculated by applying the information acquired through a literature study. Current principles used on the mine were also applied. The first layout chosen is described as a simple straightforward layout with 6 production tunnels spaced 15 m apart, and is referred to as Layout A. The second layout, named Layout B, is described as a complex chevron layout with 9 production tunnels spaced 15 m apart. This layout has a rim tunnel situated in the kimberlite ground, which is called a chevron and this made the layout more complex than Layout A. By comparing the financial results of the two layouts, it was found that Layout B is a more feasible option than Layout A. Sensitivity analyses show that both layouts are extremely sensitive to the revenue of the projects. Therefore it is recommended that Layout B can prove to be a source of additional tonnage to add to the total tonnage profile of the mine and to extend the life of mine by 20 months, only if certain financial/economic factors improve. There is, however, still some areas of the project that need to be investigated.

Jan 1, 2006

By Bruno Henrique Reis

O pó de aciaria elétrica (PAE) é um importante subproduto da indústria siderúrgica devido ao seu alto teor de Zn. Assim, tecnologias vêm sendo desenvolvidas visando seu aproveitamento, sendo o forno Waelz a mais difundida delas atualmente. Sua operação, por contar com um forno rotativo de grandes dimensões, que abriga uma infinidade de fenômenos físico-químicos, apresenta difícil previsibilidade ab initio. Por essa razão, este trabalho faz uso de uma ferramenta avançada da termodinâmica computacional, destinada à modelagem de processos, chamada SimuSage, a fim de modelar o seu comportamento. Para a criação do modelo utilizou-se também uma base de dados termodinâmicos advinda do software FactSage e a plataforma Lazarus. Com base em dados e resultados operacionais da literatura, foi possível realizar simulações no modo adiabático e comparar os resultados com os da prática industrial. Constatou-se uma grande sensibilidade do modelo com relação à quantidade de ar de entrada considerada no sistema, mas, também, boa aproximação dos resultados com relação à composição química dos produtos Óxido Waelz e Escória Waelz.

Aug 16, 2017