Search Documents

For many years the scrubbing of roaster gas carrying sulphur dioxide has been carried out at the plant of the Electrolytic Zinc Co. of Australasia Ltd. at Risdon, Tasmania, using long horizontal tubes. in which the gas stream crossed a shower of water. In order to provide for increased roaster capacity, it was evident that additional gas scrubbing capacity would be required to prevent pollution of the atmosphere.This provided an opportunity to review the whole operation of gas scrubbing and an investigation was initiated to determine the characteristics of a counter-current type of scrubber. It was hoped that a change to this type of scrubbing would also reduce the sulphur dioxide concentration of the gas delivered to the atmosphere to a negligible amount. This, paper outlines results obtained from an experimental tower which was operated under a wide range of conditions, the packing height, gas flow, water flow, water temperature, and concentration of S02 in inlet gas being varied independently. A description is given of the leading features and operating characteristics of the plant units, which are designed on the basis of the experimental results. Operation of the new scrubbing system commenced on October 5th, 1948.THE PROBLEMThe gas which is handled carries S02 which may vary in concentration from 2% to 5%, and reaches the scrubbing system at a temperature of approximately 180 deg. C. An appreciable amount of suspended material accompanies the gas which has passed the cyclone system.

Jan 1, 1949

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By K. Pirapakaran

The Geotechnical Engineering research group at James Cook University has been working closely with all the leading mines in Australia in the area of minefills. They have carried out substantial research and consulting work on the drainage and stress developments within hydraulic fills. The objective of this paper is to summarize their work during the past five years on hydraulic fills. The paper will serve as a one-stop reference, pointing to relevant literature including the authors? own publications, on various issues covering drainage and stress developments within hydraulic fills. More than 15 different hydraulic fills, representing five major mines in Australia, were studied. Their grain size distributions and placement characteristics including permeability, porosity and dry density were studied and comparisons were made with the limited in situ data available in the literature. Stress development within hydraulic fills has been studied to minimize the risk associated with barricades failure. FLAC and FLAC3D were used to model stress developments within the hydraulic fills and were compared against the approximate closed form solutions available in the literature. A laboratory model was developed to study arching effects within the hydraulic fills.

May 1, 2007

By M. K. Pelser

The purpose of this paper is not so much to provide a scientific study of the selection process for the perusal of other psychometrists or industrial psychologists?the purpose is to provide line management with a practical, relatively user-friendly guide to fair and scientific selection. The main areas that are to be covered are: ? Why fair and scientific selection? ? Job analysis ? The job requirement?selection technique circle ? Assessment centres in the mining industry?the Tavistock Collieries Ltd experience. Why fair and scientific selection? Seen from a line manager?s perspective, fair and scientific selection should be pursued for two main reasons: ? to remain within the ambits of the law ? to maximize the probability of selecting the potentially most productive and efficient candidate for the job.

Jan 1, 1997

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau&apos;s continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By William H. Lewis

Energy Research Corp., under contract to the Bureau of Mines, has developed a new miners&apos; caplamp battery. The new battery is based on nickel-cadmium technology and offers significant improvements in performance with reduced size and weight when compared to the conventional lead-acid battery presently in use. This report describes the design and fabrication of the nickel-cadmium battery, which utilizes a roll-bonded electrode structure. The final battery design has a 15-A-h capacity in a 2-112-lb package, which is over 2 lb lighter than the present lead-acid caplamp battery.

Jan 1, 1983

By Henry A. Signore

The Appalachian coalfield, located in eastern Kentucky, Pennsylvania, Virginia and West Virginia, has been one of the most productive in the United States. Total production from the Appalachian coalfield during 1994 was 340.8 Mt (375.4 million st), or 37% of the 929 Mt (1 billion st) produced in the United States that year. This region contains various coal types from high- to mid-sulfur coal in Pennsylvania and northern West Virginia to low-sulfur, compliance steam coal and premium-grade metallurgical coal in eastern Kentucky, Virginia and southern West Virginia. The region&apos;s product is in high demand in domestic and export markets. Productivity continues to improve, resulting in the primary coal operators solidifying their market positions.

Jan 1, 1995

By Murray Jacobson

Facts obtained by the Bureau of Mines on the dust-explosion hazard in air of materials used in the plastics industry are presented for 313 samples studied in the laboratory. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum energy required for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent ignition and flame propagation, and, in some instances, on the limiting oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle shape, additives, and resin structure on explosibility are discussed. Relative explosibility of the materials is related to the ignition sensitivity and explosion severity and is denoted by an empirical index. Recognition of the degree of hazard will facilitate adoption of adequate measures for preventing ignition and explosion during manufacturing or processing.

Jan 1, 1962

By J. S. Miller

The Bureau of Mines conducted surface tests to determine the feasibility of using liquid explosives for underground rock fracturing. The effects of configuration, confinement, length, critical layer thickness, and fracture-propping sand on detonation and explosive propagation velocity of desensitized nitroglycerin were studied, using polymethyl methacrylate and glass-plate reservoirs through lengths from 3 to 12 ft, with explosive-layer thicknesses from 0.1875 to 0.0312 in and in aluminum tubes 8 ft long with diameters from 2.000 to 0.125 in. Interval and continuous detonation velocity data were obtained. Under the test conditions detonation velocity was dependent upon explosive confinement and fracture-propping sand. The detonation velocity of a confined nitroglycerin explosion in aluminum tubes can be reduced by as much as 85 percent, when the tube contains fracture-propping sand. The shape of the reservoir, whether triangular or rectangular, has little effect on the detonation velocity or explosive propagation. The critical or minimum explosive-layer thickness between glass plates, capable of supporting propagation, was 0.0312 in. The presence of a fracture-propping sand in the sheetlike layers increased the critical explosive layer thickness to 0.0625 in. In nitroglycerin-filled and nitroglycerin-sand filled tubes, the minimum tube diameters successfully tested were 0.125 in and 0.375 in, respectively.

Jan 1, 1969

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale&apos;s yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of ,Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal- mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

By R. A. Hatch

This report summarizes the results of nearly 8 years research on and production of synthetic mica at the Electrotechnical Experiment Station of the Federal Bureau of Mines, Norris, Tenn. This program was undertaken at the request of the United States Department of the Navy and was financed mostly by the Army Signal Corps and the Navy Bureau of Ships through a contract with the Office of Naval Research, The original objectives included fundamental studies of fluor-phlogupite and other fluorine-micas and production of synthetic mica sheets on a pilot-plant scale. The first 3 years of this project were devoted mainly to a search for practical solutions of the many problems involved in designing and constructing a pilot plant for crystallizing fluor-phlogopite mica. The first and most urgent need was a suitable container for the corrosive mica melt. After extensive study, it was concluded that platinum, graphite, high-silica fire clay, and silicon carbide were the most promising refractories for crucibles; but none was perfect. Silicon car¬bide seemed to have the better combination of qualities, combining good corrosion resistance with oxidation resistance.

Jan 1, 1957

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Damian R. Siebert

Risk-reduction measures implemented during the design and construction of a 21-story pile-supported building adjacent to a below-grade 100-year-old sewer structure were keys to a successful foundation system. Avoiding damage to the existing sewer structure during construction activities and the future ability to access the structure post-construction were the main concerns for the utility owner. Clear communication and a deliberate design process between all parties ? utility owner, building owner, structural engineer, geotechnical engineer, architect, and contractor ? were integral to the project?s success. This collaborative process helped all parties to understand the risks, both real and perceived, and to develop mitigation measures to reduce the risks. Bringing together all parties to engage in dialogue and encouraging open communication throughout the project were paramount to its success. By implementing the joint design plan, using mutually-acceptable construction techniques, and careful monitoring, the building foundation was successfully installed and all parties? risks were averted.

Jan 1, 2011

By Thornton L. Neathery

Vertical magnetic surveys have been made over about 3, 150 miles of the crystalline area of east-central Alabama. A contour map (100-gamma interval) showing regional magnetic anomalies has been prepared (scale 1:250,000) from data points located at quarter-mile intervals on all public roads. Small one- and two-station anomalies were eliminated, leaving only areally extensive anomaly features associated with regional geology. The regional gradient was "filtered" from the basic data and the resulting magnetic configuration compared to the regional geology. Regional lines of vertical magnetic intensity trend northeast and follow the structural framework of the area. Correlations can be made between a large number of geologic and magnetic features. The strongest regional anomalies are associated with the Goat Rock, Bartletts Ferry, Towaliga, and Brevard fault structures. The Inner Piedmont area is characterized by a broad regional high. The magnetic values of the northern Alabama Piedmont grades gently northwestward, disrupted occasionally by elongate highs and lows associated with amphibolites or granites. Scattered throughout the Piedmont are anomalous areas of high magnetic intensity; some are related to magnetic-bearing rocks, and some Indicate possible mineralization. Most of the anomalies have not been evaluated,

Jan 1, 1972

Development of Technology for Complex Uranium Ores Processing on the Flotation Process Basis

Sep 13, 2010

By L. P. Weber

During the years 1983-1987, a research programme, jointly performed by the steel producers ARBED, British Steel Corporation, Peine-Salzgitter, Unimetal, and co-sponsored by the European Community for Steel and Coal (ECSC), has been carried out on steel H-piles of different shapes. The initial aim of the testing programme has been the improvement of bearing capacity, both in sandy and clayey soils. At two test sites, standard H-beams are compared to H-piles with different types of laggings or to H-piles grouted both under low and high pressure. In this paper and in view of the open european market in 1992, the H-pile capacities and their corresponding allowable loads, determined from codes, recommendations and computation procedures in use in Belgium/Luxembourg (B/L), France (F), Federal Republic of Germany (G), and the United Kingdom (UK) as well as their evaluation from dynamic CAPWAP and Case methods are compared to the static capacities measured in-situ. In addition, procedures for estimating the load/movement behaviour of H-piles from CPT, pressuremeter, and CAPWAP are compared to the measured curves.

Jan 1, 1991

By J. Kang

To obtain microbial cultures with the ability to efficiently leach copper ion from chalcopyrite, microbial samples from acid mine drainage sites were mixed and then subjected to mutation using sodium nitrite (NaNO2), diethyl sulfate (DES), ultraviolet light (UV) and their combinations. Mixed cultures with a much stronger ability to leach copper ion (identified as mixed cultures A, B, C, D and E) were obtained by screening on leaching media. Leaching tests showed that mixed culture E had the best leaching performance and increased the Cu2+ content by 120.5% in 20 days, compared to a control without mutation treatment. Mixed culture E grows well on Leathen leaching medium supplemented with Cu2+ (at a final concentration of 32 g/L), reaching 3.2 × 107 cells/L after 15 days, while the unmutated control culture cannot survive beyond 15 days, indicating that mixed culture E is more tolerant of high concentrations of Cu2+. In addition, continuous leaching by mixed culture E is very effective at a pulp density of 1%. These results suggest that it has the potential for industrial applications.

Jan 1, 2008