Search Documents

The cyclone, or centrifugal separator, ,is firmly established in industry as a low cost separator of solids from gases.While it will also separate fluids of different densities, and solids from liquids, its main use is to remove relatively fine dusts from gases whose pr~erties are generally not greatly different from those of air. This latter phase of operation is the one that will be dealt with here.The duty of such a cyclone separating system is to take in a supply of dusty gas and separate it into its components of dust and clean gas as perfectly as possible for the least consumption of pressure head. Any separation at all causes pressure loss and, in general, the greater the separation, the greater the pressure drop needed to effect it. The percentage of dust in suspension which is separated from the gas-dust mixture is commonly called the collection or separation efficiency. Overall or "true" efficiency must take pressure drop into account and may be considered as proportional to the ratio of the percentage of dust collected to the resultant pressure drop. For any cyclone It will vary with different dusts.Many commercial adaptions of the simple cyclone are made solely on the basis of pressure drop improvement, without taking into account the effect on separation efficiency, probably because the latter is so difficult to assess correctly. It appears unfortunate but true that the majority of such adaptions and patent gadgets fitted to cyclones which decrease pressure drop, do have an adverse effect on separation. In other' words, the true efficiency is seldom increased but often diminished.Without a knowledge of what actually goes on inside a cyclone, it is impossible fully to appreciate the real effect of a modification. For instance, it is on record that a cyclone...

Jan 1, 1949

Gas-liquid contacting in the packed bed is a common operation in metallurgical reactors. Research has shown that, unlike wetting flow, non-wetting liquid flows in the form of discrete droplets or rivulets. Thus, modeling of the liquid phase as a continuum is in contradiction to the observations. Also, for the non-wetting case, continuum models have failed to describe liquid flow path when the liquid source is a point source. The aim of the current work is to put forward a combined Lagrangian-Eulerian approach to model the liquid and gas flow in the packed bed. Liquid is assumed discrete and modeled using a force balance approach. Gas is assumed to be interpenetrating continua and modeled using k-emodel for turbulent flow. Structured packing is assumed and x- ray imaging technique is used to visualize liquid flow lines in the bed. Simulation results for liquid flow path compared with the experiments.

Jan 1, 2006

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By Christopher J. Bise

INTRODUCTION Before a mine is planned in detail, a preliminary analysis is often conducted. This preplanning permits the mining engineer to make a rapid assessment as to whether or not a particular mining property warrants further consideration. In fact, a properly conducted preplanning phase can come within 10% to 20% of the actual results, thereby saving the mining engineer valuable time before committing himself to a fine-tuned analysis. The questions to be answered by mine preplanning are (1) What will be the operating conditions for the mine? and (2) How long will it take to complete the project? To answer these questions, calculations dealing with reserve estimation, production planning, man- power planning, and project scheduling are conducted. The following sections discuss these various phases of mine preplanning in greater detail. RESERVE ESTIMATION The estimation of the various characteristics of a reserve, such as quantity, grade, and thickness, is an ongoing process throughout the life of a mining venture. However, the reserve-estimation phase of mine planning is more closely associated with the preplanning phase. There are many different techniques employed in reserve estimation of solid mineral deposits; variations among them are introduced because of such considerations as ease of application or level of accuracy. In any event, each technique is developed in the following manner: (1) the mineral body is represented pictorially and then subdivided into blocks related to one or more samples of exploration data, (2) the area and volume of each block is determined, (3) the volumes are converted to representative tonnages (or, for example, grades), and (4) the results are tabulated. To illustrate this procedure, the polygonal (area-of- influence) technique will be presented due to its ease of application, flexibility in dealing with different deposits, and general acceptance. The polygonal method assumes that all characteristics of a mineral body extend halfway between a point of observation and any other point of observation. The explored portion of the mineral body is represented by polygonal prisms whose depths relate to the characteristic in question (grade, thickness, etc.) and whose plane bases relate to the area of influence of each point of observation (drill hole, etc.) as shown in Fig. 1. The polygons must be constructed in a definite order, usually clockwise and from the periphery to the center of the deposit. Table 1 can then be used to calculate the characteristics in question. Since, by definition, the polygonal method assumes that the characteristics of a mineral body extend half- way between points of observation, it becomes readily apparent that the evaluation of a vertical-drill hole exploration program requires that the sides of the polygons be formed by the intersection of perpendicular bisectors (Fig. 2). Figs. 3 and 4 show correct and incorrect construction of the polygons. The criterion for correct construction of the polygons is that all points within a particular polygon must be closer to its rallying point than those located in any other polygon. This is clearly not the case for certain points that are located in the polygon containing rallying point B in Fig. 4. Although this method can be used where the drill holes are irregularly spaced, calculations become less tedious when a square net (Fig. 5) or a chessboard (Fig. 6) grid is adopted. The numbers shown in Figs. 5 and 6 represent the relative weight for each of the shaded areas. In general, the greater the number of polygons, the more continuous the mineral body, and the more regular the grid, then the more accurate the computations will be. PRODUCTION PLANNING Before an acceptable evaluation of the production potential of a mine can be determined, a thorough exploration program should be conducted. It seems obvious that the nature and properties of the deposit and adjacent strata, the presence of impurities, and other mining conditions should be adequately determined prior to production planning and equipment selection. The lack of sufficiently detailed knowledge of the many mining parameters has led to the failure of numerous operations. For example, targeted production tonnages and equipment sizes for a coal mine are intimately related to the seam thickness. Needless to say the quality of information that is gathered from an exploration program can have a tremendous impact on the production plan. Production plans are developed initially by determining reasonable shift tonnages per operating section. Most of the time these values are developed from his-

Jan 1, 1986

By Lawrence M. Gochioco

One of the best kept technology secrets in U.S coalmining history involved a robust coal geophysics program used by a local coal company to detect and map various geologic anomalies and man-made structures ahead of mining for nearly 15 years. Several original mine plans were changed as a result of findings from two-dimensional (2D) and three-dimensional (3D) seismic data. They indicated the presence of geologic anomalies in reserve areas that could adversely impact future mine development and longwall production. By combining the surface seismic and exploratory drilling methods, the coal company learned how to properly leverage its risk by gathering a lot of useful subsurface information before making major commitments.

Jan 1, 2005

By David Gatto, Nicolas A. Willig-Friedrich, Jeff A. Segar

"With the increasing demand for electricity, and requirements to generate this power cleanly, more producers are turning towards hydroelectric power. A project in Iowa currently under construction will retrofit an existing Army Corps of Engineers Dam with a hydroelectric generating facility. The design of the intake structure requires the construction of a diaphragm retaining wall. The T-shaped diaphragm wall elements retain an unbalanced fill height up to 21.3 meters (70 feet). The design required a single production element be constructed, tested, and instrumented prior to beginning construction of the rest of the elements. The testing included extensive concrete mix design development, coring, and Cross Hole Sonic Logging. Installed in the other production elements are 10 inclinometers, 4 pressure cells, 4 piezometers, and multiple survey monuments. Some of these instruments require manual readings while most are monitored by an automatic data acquisition system and instantly transferred to a website providing real-time graphical display of the data. This paper will discuss the construction of the diaphragm wall from the contractor’s perspective when working on a site only large enough for two service cranes and a Hydromill excavation unit, without any storage area on the construction pad, describe the testing performed and the quality control procedures employed, and investigate the information gained from the automated instruments providing real time measurement readings.INTRODUCTIONIn 1964 the US Army Corps of Engineers (USACE) constructed a dam by raising the surface grade approximately 34.7 meters (114 feet) above the natural ground line using a combination of fill types. This earthen dam stretched slightly longer than a mile intersecting the flow of the existing Des Moines River. The center of the dam is a concrete spillway consisting of 12 monolith sections. On each end, three of the sections extend 42.6 meters (140 feet) from the spillway to transition from the concrete dam sections to the earthen dam section. Adjacent to these three sections on the East end is where the contractor is actively working, for a private developer under a lease agreement with USACE, on this site to convert it to a Hydroelectric facility licensed for an output of 36.4 megawatts, enough power to meet the needs of about 18,000 homes. To create this, a powerhouse structure, housing two vertical Kaplan turbines is being added to the downstream side of the existing dam. From the power house, two penstock pipes will be cored through the existing concrete monolith sections and connect to the Intake structure on the upstream side of the dam. Protecting and reinforcing the dam adjacent to the intake structure is a new diaphragm wall. This wall is constructed using T-shaped diaphragm elements, acting as a cantilever retaining wall for the intake platform. Figure 1 shows a diagram of the upstream features of the construction."

Jan 1, 2016

By Jiwen Zhang

Abstract Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

By Jiwen Zhang

Due to the blocking nature at the crusher station, straightforward application of queuing theory cannot give realistic results on the performance of a shovel-truck-crusher system. A new queuing network-based model has been developed in which, the crusher station is formulated into an open queuing network and the whole shovel-truck-crusher system into a closed queuing network with the crusher station as a special server. To fully account for the influence of blocking, Monte Carlo simulation is first used to obtain the performance parameters of the open queuing network for the crusher station. The closed queuing network for the entire system is solved by applying the Extended Summation Method (ESUM), in which the crusher server is described by the simulation results. The model has been applied to the Yuanbaoshan open-pit coal mine to analyze its shovel-truck-crusher system and to improve its efficiency. Results indicate that the blocking at the crusher is an important factor affecting the crusher output and in turn the efficiency of the whole system, and prove that the model can realistically describe the behavior of such systems.

Oct 1, 2009

The commonly used Stopes-Heerlen coal petrographic classification and nomenclature has over the years been subject to variable interpretations. This paper discusses the problem with specific reference to the inertinite maceral group. The effect of various interpretations of the Stopes-Heerlen system on maceral analysis is discussed and illustrated by means of comparative analyses conducted by a number of laboratories in Australia.An attempt is made to define the reflectance thresholds used by the authors to subdivide the inertinite group; the genetic and technological significance of these thresholds are compared.The difficulties of distinguishing structured and nonstructured macerals of the inertinite group are discussed in terms of possible improvements to the present StopesHeerlen system by extending the classification to include transitional maceral types.

Jan 1, 1970

By H. Akbari

Ordinary portland cement (OPC) is the key pozzalonic component of the concrete mix widely used as a construction material worldwide. B illions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of C O2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic C O2 emissions each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon footprint of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the nonmetallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned extracting some of the valuable metal oxides from fly ash prior to using the major nonmetallic portion of the fly ash for geopolymer concrete application. The results obtained from this study showed that the compressive strength of geopolymer concrete compares favorably with that of conventional concrete prepared using OPC.

Dec 1, 2013

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By B. Elevli

This paper deals with the selection of alternative accesses to a podiform chromite orebody in Turkey. The most important alternatives studied in a related project have been stated as a new vertical shaft and a ramp system. The comparison of these alternatives have been carried out on the basis of total investment costs, ore transport unit cost and net present value (NPV) of overall project for various depth. The results show that up to the depth of 700 m, the total investment cost and NPV favours the ramp access while unit ore transport cost make the shaft access preferable.

Jan 1, 2002

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By Colwell J. B, Constantine A. E

A unique, regional grid of deep (12 - 14 second record length), seismic reflection and refraction data has been recorded by the Australian Bureau of Mineral Resources (BMR) across the offshore Gippsland Basin and parts of the adjacent Bass Basin, in southeastern Australia. These data have been combined with onshore mapping to produce a new model for the development of the Gippsland and adjacent Bass Strait basins. Overall, the Gippsland Basin contains up to 12 - 14 km of sediment in an ESE-trending depocentre bounded on its north and northwestern margins by a detachment ramp, and on its southern side by a relatively linear, listric fault system. The basin, together with the adjacent Bass and Otway Basins, appears to have formed as part of a linked, largely- strike-slip to 'transtensional' system, which started to extend through Bass Strait, probably during the latest Jurassic. Each of the basins developed by movement on a common detachment or detachment complex, which produced headwall extension at their western ends, in the areas now occupied by the Strzelecki Ranges, Otway Ranges - Torquay Sub-basin, and Robe Trough. Adjustments and reactivation from the mid Cretaceous of several postulated microplates in the region, largely in response to Tasman Basin rifting, gave rise to the wrench-related and compressional structures which form the major petroleum targets in the Gippsland Basin. However, the same process formed largely extensional stuctures in the Bass Basin. Our interpretation of the tectonic history of the Gippsland Basin leads us to the conclusion that there may have been several phases of petroleum generation and migration, and that potential petroleum traps appear to exist in the deeper section, in structures sometimes not reflected at the top or near-top Latrobe Group levels.

Jan 1, 1992

By Martin J. Pedley

The use of soil nailing has grown steadily in the UK over the last 15 years and it has recently become more popular in the Republic of Ireland. This paper presents three soil nailing temporary works case histories where the technique has been used to support steep excavations in difficult ground conditions. It demonstrates the effectiveness of soil nailing when applied in appropriate conditions. Details of design methods and construction techniques are described and those aspects of soil nailing that will benefit from further study and development are identified.

Jan 1, 2000

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and requires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged because a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced. Difficulties sometimes encountered in continuous filter operation can be summarized in the following four categories: 1) Low filtration and/or washing rates due to blinding of the filter medium. 2) Poor cake discharge resulting from sticky cakes, filter medium blinding, or too thin a cake for the particular type of filter. 3) High filter media costs caused by short life and frequent down times for cloth changing. This results from blinding or from abrasion by the scraper blade when cakes are thin. 4) Blowback of filtrate at cake discharge because not enough air passes through the cake to purge the drainage area and filtrate lines during dewatering. To reduce or eliminate blinding tendencies several modifications have been tried, for example, cover-cleaning showers, blowback under the feed slurry, and snap-blow cake discharge. In many cases, however, this simply retards the rate of blinding, since the filter medium is kept clean at its outer surface only by these methods. As blinding usually occurs within or on the back of the medium, the operator is finally forced either to remove the cloth and scrub the medium intensively with a cleaning solution or acid-rinse it on the filter—all resulting in down time, short cloth life, and additional costs.

Jan 1, 1959

By Roy Woodall

Successful mineral exploration is the lifeblood of the mining industry. Contrary to what the environmental lobby would have the world believe, the industry is replacing the metals it is extracting. The reserve base has not changed significantly in 20 years (Fig. 1.) Mineral exploration is a research activity. First there is the idea, the vision or the intuitive thought. The experiments follow. These involve repeated phases of data gathering, data interpretation and concept testing through drilling. For many companies, exploration is the main investment in scientific research. Each mineral exploration experiment may involve years of costly work. Despite the improving tools of science and technology, the investment remains high-risk. Only the promise of high rewards, or desire to survive as a mining company, will stimulate the necessary commitment and level of investment. Confidence that an economic return can be achieved, confidence in the science and technology being applied and confidence in the people involved are the foundations upon which successful mineral exploration is built (Woodall, 1984). The challenges facing the explorationist in the 1990s fall into two categories: - the challenge to make the activity economic; and - the challenge to make the activity socially and, therefore, politically acceptable.

Jan 1, 1992