Search Documents

A model has been developed for drum scrubbing which allows selection of geometry and power input. Specific aspects considered are: Calculation of total static and operating volumes. Total residence time based on total operating volume. Solids residence time based on solids operating volume. Selection of the aspect ratio. Alteration of operating fill to allow for smaller or larger feed openings. Selection of proportion of critical speed. Calculation of shell and motor power requirements. The model uses either solids or total residence time to calculate the required operating volume. The solids residence time is based on the proportion of coarse solids in the feed. Material finer than the reject size is considered as part of the slurry. The solids operating volume is the static volume plus the surcharge on the discharge weir required for flow of the solids from the unit. The total operating volume is the static volume plus the surcharge on the discharge weir for the total flow to exit the scrubber. The burden density is calculated from the coarse solids bulk density and the slurry density that includes all the fine solids. Power is calculated using the Liddell and Moys correlations for burden position and shape, and the operating rotational speed. Results from the model (especially power) have been verified from industrial installations of significant size. Predicted and observed power draws are within two per cent. A check against the JKMRC mill model shows power draw prediction agreement to within four per cent.

Jan 1, 2004

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 (PL 109-236, 2006) established the Office of Mine Safety and Health, functioning as the Office of Mine Safety and Health Research (OMSHR) within the National Institute for Occupational Safety and Health (NIOSH) and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued more than 150 contracts focused on worker health and safety. Initial funding for this program was provided by the United States Congress through two emergency supplemental appropriations and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation. Ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website (www.cdc.gov/niosh/ mining/researchprogram/contracts/index.html) and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously (Snyder et al., 2016).External contracts are broadly classified by the following areas:• Communications and tracking.• Emergency response.o Self-escape and breathing air supply.o Refuge alternatives.o Escape and rescue.• Equipment safety.• Fires and explosions.• Ground control.• Mine environmental systems (mine ventilation and atmospheric monitoring).• Worker/workplace health and safety.Contracts are issued under a request for proposal (RFP), through a broad agency announcement (BAA) or under an interagency agreement (IAA). An RFP solicitation includes a specific problem description and a well-defined scope of work to guide the offeror in preparing a bid to conduct the research. Under the BAA several problem areas are described and the offeror develops the scope of work and deliverables for the proposed research. An IAA is very similar to an RFP except it is a contract between two federal government agencies."

Jan 10, 2018

Currently raw brown coal is fired in the Latrotx; 'ahcc th,iki~, Lanying with it two major penalties, (a) boiler efficiency of 65 - 70 per cent (in terms of GCV), (b) much higher boiler cost than for black coal. Drying the coal, in energy-efficient, and cost-efficient manner, opens the way to efficiencies of order 88 per cent and enables the lower cost black coal type boilers to be used. With the higher boiler efficiency goes much higher combustion temperatures and the effect of this on radiative heat transfer is a major factor in reducing boiler cost. In a fluidised-bed combustor the temperature is controlled to 800C - 900C. In a pulverised fuel combustor higher temperatures are however achieved and can increase boiler fouling due to the salt content of the coal. This is a problem which needs to be solved. Victoria has the prospect of lifting efficiency from 28/29 per cent to 35 per cent, of reducing carbon dioxide output correspondingly and reducing cost of power stations. So far as gasification is concerned, efficient removal of liquid water from the coal is important to the overall efficiency.

Jan 1, 1992

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

The Fourth Industrial Revolution has driven significant advancements in autonomous robotic systems, particularly in subsea exploration and offshore mineral dredging. This review examines the latest developments in electrically powered quadrotor-track subsea robotic crawlers, highlighting their potential to enhance efficiency, mobility, and adaptability in challenging underwater environments. The integration of advanced automation, artificial intelligence, and real-time control systems has paved the way for more effective robotic solutions in offshore mining. This study explores the dynamic performance of hydraulic crawlers to quadrotortrack robotic dredgers, focusing on their propulsion, navigation, and stability under high hydrodynamic conditions. By leveraging state-of-the-art technologies such as lithium-ion battery power systems, intelligent microprocessors, and sensor-based control mechanisms, these robotic crawlers offer a promising alternative to conventional subsea excavation methods. Furthermore, the review analyses recent experimental and simulation-based studies that assess the feasibility and performance of these systems in real-world applications. The findings of this review provide valuable insights into the role of 4IR in transforming subsea robotics for offshore mineral dredging. By addressing existing limitations and identifying key technological advancements, this study contributes to the ongoing development of nextgeneration robotic systems capable of operating efficiently in extreme underwater conditions

Jan 30, 2026

By R. S. Dean

As set forth in the decision of the Trail Smelter Arbitral Tribunal, dated April 16, 1938 This Tribunal is constituted under and its powers are derived from and limited by the convention between the United States of America and the Dominion of Canada signed at Ottawa, April 15, 1935, duly ratified by the two parties and ratification exchanged at Ottawa, August 3, 1935 (hereinafter termed "the Convention") . . . The duty imposed upon the Tribunal by the Convention was to "finally decide" the following questions: (1) Whether damage caused by the Trail Smelter in the State of Washington has occurred since the first day of January 1932, and, if so, what indemnity should be paid therefor? (2) In the event of the answer to the first part of the preceding Question being in the affirmative, whether the Trail Smelter should be required to refrain from causing damage in the State of Washington in the future and, if so, to what extent? (3) In the light of the answer to the preceding Question, what measures or regime, if any, should be adopted or maintained by the Trail Smelter? (4) What indemnity or compensation, if any, should be paid on account of any decision or decisions rendered by the Tribunal pursuant to the next two preceding Questions? In this decision reported to the Government of the United States of America and to the Government of the Dominion of Canada, the Tribunal answered the first question in its entirety and reserved decision on the other three questions in accordance with the following extract from their decision

Jan 1, 1944

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under development since. 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1998

By Madgwick J. C

Microaerobic biodegradation oflow-grade manganese dioxide slurry tailings was demonstrated in enrichment cultures treated with dilute molasses at 30°C and pH 5·8. Supplementary nitrogenous nutrients, yeast extract addition and pH adjustment were not required.Continuously stirred, air-limited reactors were superior to still intermittently agitated cultures, in that, at 5 per cent (w/v) MnOz tailings and 5 per cent (w/v) molasses, the yield of 0.12 g Mn++/g molasses, the rate ofleaching of 1·06 g Mn++/l/d and a recovery of Mn++ of 58 percent from MnOz were 2·8 times, 1·7 times and 1·9 times greater, respectively. The best compromise in yield (0·45 g Mn++/g molasses) and rate ofdissolution (0·73 gMn++/l/d) was at 1 per cent (w/v) molasses in a stirred reactor.Where leaching organisms were separated from sterile ore by a bacteria impermeable membrane leaching was shown to be some 20 per cent due to diffusible metabolites and 80 per cent due to a direct contact between the bacteria and the ore particle's surfaces.

Jan 1, 1986

By S. K. Bradford

(Pittsburg Meeting, March, 1910.) FOR years past I have traveled in quest of promising mining-properties, over almost impassable mountain-trails to remote places in the mining-regions, usually, many miles from an assay-office. If, upon examination, the formation and the ore-deposit appeared favorable, a quick determination of the value of my samples was necessary, in order that I might take intelligent action with reference to the acquisition of the property. A journey with my samples to civilized regions often meant weeks of delay, and perhaps loss of opportunity. How many, under similar circumstances, have returned with their assay-results from such a journey, only to find that some audacious speculator had " optioned" the property ! True, a first payment could have been made and the chances taken on the results; but experience has taught that rich-looking ore is not of necessity valuable. Personally, I would not hazard a ten-dollar bill on any property without first determining by assay the value of the ore. To carry the usual complete assay-paraphernalia over such mountain-trails was impracticable by reason of the loss of time involved, the great expense of transportation (charged according to weight), and the fact that a few such trips would almost certainly wreck the outfit. For these reasons I began a process of elimination and substitution which finally enabled me to carry, in an ordinary 26-in. valise, sufficient apparatus and supplies for, say, 100 assays of adequate commercial accuracy. My final outfit was as follows: APPARATUS. Small hammer; steel mortar (2.5 in. wide, 3 in. high, with stand sawed off flat, so that it can be used as an anvil and for

Jan 1, 1911

By R. L. J. Phillips

"The environmental impact of the Rabbit Lake project is presented. Baseline data for fish, water, air and radon collected in 1973, 1975, 1980and 1986, are compared with post-development environmental monitoring data. Predicted environmental impacts for the developed Rabbit Lake and B-zone deposits are compared to the actual impacts. INTRODUCTIONThe environmental impact of the Rabbit Lake project has been documented through the years in several submissions to the government agencies. In 1972, the environmental baseline study for the Rabbit Lake area was completed prior to any mining activity at the Rabbit Lake pit (Fig. 1).Sampling concentrated on Hidden Bay and Pow Bay, which received the treated effluent and the waters drained from Rabbit Lake respectively.A second baseline study was done on the Collins Bay area in 1980(Fig. I) in preparation for the mining of the B-zone pit. The detail in this study was considerably greater than the detail in the previous study. Collins Bay and Harrison Peninsula were the areas sampled. The B-zone deposit is being mined at present.With the discovery of the A-zone, D-zone and Eagle Point deposits, it was decided in 1986 to begin proceedings to obtain approval from Saskatchewan's Department of the Environment, and from the Atomic Energy Control Board to develop these deposits.In preparation, a third baseline study of both the Rabbit Lake and Collins Bay areas was done in 1986 and 1987. The emphasis was to establish the baseline at the three new deposits, to quantify the actual impacts of the existing Rabbit Lake operations and to confirm the Collins Bay B-zone (1980) impact predictions. The new deposits will allow us to continue to produce uranium into the future. In January 1988, Saskatchewan approval was received.Since 1975 in the Rabbit Lake area and 1980 in the Collins Bay area, routine environmental monitoring has been done. This has resulted in one of the largest and most comprehensive environmental data bases in North America in mining. By the time the Eagle Point deposit is mined to completion, there will have been data collected for approximately 40 years.Further discussions follow which describe the impacts of the past (1972 to 1984), the present (1985 to 1987) and the future. In addition, the past and present performances and the future plans of the .waste management systems will be discussed."

Jan 1, 1989

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By B Vorster

Falls of Ground is one of the highest causes of incidents, accidents and fatal injuries in our mines today. These falls of ground may occur as soon as the face is exposed after blasting or after machine cutting. The falls of ground can also occur after support has been installed. There are many reasons why these falls occur before and after supporting of the face. It is therefore important to support the exposed face as soon as possible to prevent the falls of ground. It is also very important to support the face with the correct support products and to support the face as designed and required by the mining engineers. The possible reasons for falls of ground, possible support methods and the products available will be discussed in this presentation. In typical conventional narrow vein stoping operations, the use of conventional temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The author wishes to discuss the following items in this paper:- ? Introduction ? Basic face behaviour after exposure ? Controllable Parameters ? Mining Engineers support designs ? Primary and Secondary Support ? Products available for prevention of falls of ground

Jan 1, 2008

By Stephen C. Tadolini

PC-Strand tendons, commonly referred to as cable bolts, have become a major rock reinforcement device for underground mining and civil applications. The most common configuration is a 1+6 strand, which designates a center king-wire, with six outer wires wound around it to form a 0.6-in (15-mm) diameter cable. The capacity of this tendon approaches 30 tons, but the performance is largely dependent on the anchorage medium and the ability of the system to transfer stresses back into the rock mass while reinforcing and suspending the immediate roof. Recent developments to improve the transfer mechanisms of the PCstrand via the anchorage medium by impregnating the individual wires with uniquely designed deformations have resulted in improved anchorage and subsequent cable bolt performance. This paper describes a series of laboratory tests used to develop the initial indentation patterns and numerical modeling simulations that were undertaken to refine and optimize the final designs. The new, indented PC-Strands, offered in both bright and properly galvanized, have been tested in the field and are being used effectively in two new cable bolt products. The results of the laboratory, computer modeling, field testing and in-situ installations provide a glance at the next generation of cable bolts. This suite of testing shows how they will improve the safety and serviceability of openings under adverse ground conditions.

Jan 1, 2012

By B McCreath

Industrial process water for the Commodore Coal Mine and the adjoining Millmerran Power Station is provided by pumping secondary treated sewage effluent 100 km from the Wetalla Sewage Treatment Plant near Toowoomba. (A separate source is used for potable water.) The effluent is not of sufficient quality for discharge to a watercourse, but it is suitable, with further treatment, for the mine and power station. In designing and constructing the pipeline, special emphasis was placed on preventing accidental spills or planned releases to the environment. The pipeline and associated works can transfer 1000 ML/annum for reuse in the coal mine and power station.

Jan 1, 2003

Mr. Murray said: Having recently returned from a visit to America, it may be of interest to members to hear something from me of the mining fields and metallurgical works which I had the opportunity of seeing, and the impressions which I formed concerning general practice and conditions there, as compared with our Australian standards in the mining industry, and in matters generally.The most striking feature of the North American continent is thehuge plan upon which Nature has built, the multiplicity of immense mountains, rivers, and lakes, the snow-covered tops of the former forming reservoirs for the latter during the summer months, being most impressive to the Australian visitor. Starting from Vancouver I travelled east for over 500 miles through the wonderful Canadian...

Jan 1, 1927

By R. E. Moore

Refractories are unique ceramic materials, which are used in large quantities in steel making furnaces, metal smelting vessels, and glass melting tanks. They are required to possess high thermal shock properties and good slag corrosion resistance as well as creep resistance at high temperatures. Therefore, they are made from very refractory minerals such as lime, periclase, corundum, spinel, and zirconia. Slags are vitreous materials produced as a residue in steel refining processes. They cover a wide range of compositions and may contain pure oxides, silicates, and sulfides as well as fluoride phases depending on the melting and smelting processes. These minerals exhibit spectacular cathodoluminescence color under electron bombardment; therefore, cathodoluminescence (CL) microscopy is found to be a superior technique for the characterization of refractory corrosion by slags. Examples included in this study are (1) reaction of fluorine containing mold slags with ZrO2-C nozzle refractories promoting crystallization of the Cuspidine, Ca4Si2O7(F,OH)2, (2) corrosion of fusion cast refractories in TV panel glassmaking furnaces and formation of glass defects, and (3) reaction of spinel based castable refractories with copper smelting slags.

Jan 1, 2001

By John D. VandeKraats

Yielding rock bolt support systems have been developed to accommodate ground movement in shifting ground such as in coal operations; in creeping ground such as salt, trona, and potash; and in swelling ground associated with some clays. These systems, designed to remain intact despite ground movement, should enhance mine safety and help contain costs in areas where rebolting of rigid non-yielding systems is typically required. Four such systems were tested in straight tensile pulls in the laboratory. They include the Slip Nut System from Dywidag Systems International USA, Inc., Ischebeck's bolt mounted Titan Load Indicator, Rocky Mountain Bolt Company's Yielding Cable Bolt, and a rock bolt installed variation of the yielding steel post developed by RE/SPEC Inc. The first two systems are currently marketed products and the latter two are prototype systems. Each system responds to load and displacement by yielding in a unique manner. All are designed to yield at predetermined loads. A description of each system and its yield function is provided. Each system was tested over its prescribed yield range in a test machine. At least five tests were performed on each system. Each system yielded and continued to provide support according to its design. Each shows promise for ground control use in shifting or creeping rock. This work helps to illustrate the comparative differences in performance between these specialized systems and the applications where they may be most useful.

Jan 1, 1996

By M Rattenbur, A B. Christie, S C. Cox

A new minerals initiative to increase the level of understanding of New Zealand's mineral resources and to promote the development of minerals began earlier in the year in a partnership pilot-project between Crown Minerals and the Institute for Geological and Nuclear Sciences (GNS). The project aims to gather a set of comprehensive geoscientific data and build a series of digital GIS packages to highlight New Zealand's mineral prospectivity. The pilot study was carried out at a regional scale, and is focussed on mesothermal gold mineralisation in the South Island. A significant amount of geological data and information was sourced from open file technical reports held by Crown Minerals and from various databases held by GNS and has now been compiled into a single GIS dataset, which will soon be made freely available to interested parties. In addition to this comprehensive data compilation, prospectivity modelling using Weights of Evidence techniques was undertaken to highlight those areas likely to contain ore deposits. It is clear from this study that the South Island of New Zealand remains highly prospective for mesothermal gold mineralisation. Many of the highly prospective areas, which also contain historic mine workings, remain open for exploration. The study not only highlights these areas, but also other areas where the potential for similar mineralisation exists, in all likelihood with no surface expression. The study has also highlighted the value of many of the open-file technical reports held by Crown Minerals and the need to carry out additional studies using this and other available data at a more detailed level, possibly as the basis for a web-based minerals information system.

Jan 1, 2002

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989