Search Documents

By Beatriz Pereda, Ana Clara Fonseca da Silva, Tiago Seixas Bittencourt

Reinforcing steel bars are usually specified based on mechanical properties with flexibility in chemical composition and processing. Most developments, in these steels, are normally focused on alloy and process design to reach minimum cost and conformity to specification. Processing routes using quenching and self-tempering (QST) and accelerated cooling are the most common. Microalloying with V and Nb have been used in rebar. When acicular constituents must be avoided, a combination of Nb microalloying with judicious control of cooling is one of the preferred options. Niobium can contribute to improvement in tensile properties through austenitic grain size control during hot working, precipitation hardening due to carbonitrides or clusters, and hardenability increase. In the present work the alloy design and development processes of a Nb microalloyed steel for rebars are presented. The designed steel has fulfilled the required specification and is under regular production. Austenitic grain size refining – when comparing with the “basic composition” normally used was observed, even without any change in the thermomechanical processing cycle. There are indications that precipitation hardening may also occur. Results indicate that Nb is a good alternative as a microalloying element in rebars.

Oct 1, 2019

By Fábio Heiji Yamada, Marcelo Koiti Fugihara, Ruano Fonseca Araujo

Conception the simulation and optimization technologies for industrial processes applied in the mining environment: tools and methodologies. Clarifications provided about the differences of these techniques when compared with static analysis (intuition, use of static spreadsheets, etc.). Presentation of practical cases at several big mining companies in Brazil. These projects will be presented and illustrated through dynamic simulation models developed at those companies, each one with its set of objectives, scope and results (for example: sizing the number of equipment, silo, piles related to the mining processing, logistics, ROM transportation, mine operations plan, etc.).

Oct 3, 2019

By Tatiana Scarazzato

Neste trabalho, a cronopotenciometria foi utilizada para estudar o transporte de íons de um rejeito de um processo de deposição de cobre isento de cianeto através de membranas heterogêneas. Para tanto, utilizou-se um galvanostato e fez-se o registro da diferença de potencial através da membrana por meio de dois eletrodos de referência. Os resultados indicam que o transporte dos íons sofre interferências devido às reações de oxirredução da água. Além disso, a resistividade do ácido orgânico pode causar um aumento da resistência elétrica do sistema. Verificou-se, também, que o valor de densidade de corrente limite pode variar em função da espessura da camada limite de difusão.

Aug 16, 2017

By Alberto Lainati

The Bar Reducing and Sizing Technology has a core function in the value-chain for the production of rolled SBQ (Special Bar Quality) products. The EVO 2+4-roll is based on the compact combination of a 2-roll high-reduction module followed by a 4- roll low-reduction module for precise sizing. The EVO 2+4-roll mill, allows to gain significant technical and economical advantages in the hot- and post-rolling process routes: dimensional and surface accuracy, quick adaptability to processing variances and to small lots requirements, superior technological features of as-rolled product, competitive capex and opex. The EVO 2+4 unit has a very compact design, which makes it suitable both for new mills and upgrade applications.

Aug 17, 2017

By André Oliveira

The present paper describes state-of-the-art Pulverized Coal Injection technology with focus to Dynamic Distribution guaranteeing highest accuracy on equal distribution and being thus one of the key factors enabling constantly highest injection rates. As an alternative to the construction of a new plant, existing plants may be modernized and upgraded to latest technology. Two recent examples are presented. As a conclusion, two case studies of return on investment are showing that the PCI technology, both for new facilities as well as for upgrades, is very profitable and mandatory for high blast furnace operation effectiveness.

Aug 17, 2017

By José Francisco Cabello Russo, Késsius Bortolan Menezes, Henrique Dias Gatti Turrer, Denílson Rodrigues de Araújo

With the start-up of the Minas-Rio system, Anglo American, in Conceição do Mato Dentro, MG, in 2014, a methodology was also implemented and certified to perform the tests to obtain the results of TML (Transportable Moisture Limit). Such a parameter provides the maximum moisture content contained in the material that could be transported without the risk of the cargo liquefaction process, which could lead to incidents such as the tipping of ships carrying iron ore concentrate in bulk on the deep water. This means that when loading a ship, the moisture content of the material to be transported should not be higher than the TML reference value, obtained in a physical test and intrinsic to the material. Should this occur the charging may be rejected. From 2014 a downward trend was observed for this reference parameter in the Minas-Rio system, with results approaching the moisture of the filtered product, bringing risks to the operation of the project. In this way, an investigation of the possible causes for understanding this downward trend was required.

Oct 3, 2019

By Javier Martinez Rubio

In this paper we will discuss the benefits of a very innovative way of introducing MgO in the blast furnace operation through the sinter, using mini lumps of dunite. By changing the traditional way of using an MgO bearing material in fines form (particle smaller than 5 mm), most of the MgO inserted material behaves as inert during the sintering process, with the effect of having the following parameters (among others) improved: productivity at the sintering bed, permeability inside the blast furnace, energy consumption, stability of the operation.

Aug 16, 2017

By Gerd Weyand

Gontermann-Peipers GmbH (GP) Germany developed a new, high alloyed steel grade for the manufacturing of back-up rolls. The advanced GP double pour casting processes provide highest flexibility in being quite open in rolls work layer chemistry and hence microstructure with no influence on core respectively neck properties. GP took the process advantage to provide a brand new back-up roll grade with remarkably reduced roll wear while operating with textured work rolls. In the meantime several successful trials have been made with this new roll grade on different Skin Pass Mills. As a result the performance of back-up roll and thus availability of mill will be improved while specific costs for mill will drop. This quite new back-up roll grade has recently been launched. As next step increasing the field of applications is under progress.

Aug 17, 2017

By Gergö Rimaszéki

Due the fast growing of pig iron and steel in the last years associate with some mineral resources changes (Hematite?Itabirite), has been checking the sinter feed degradation. The typical sinter feed (0.15;-6.3 mm) has become limited and the rapid growing production resulted in more and more fine ore (< 150 µm) availability in the market. The sinter plant operators are facing several new challenges since the mixing and granulation- and the sintering behavior of the fines containing mixtures often differs from the traditional sinter feed´s behavior. The utilization of fines in the sinter plants might increase the process water consumption required for the mixing and granulation process or even the solid fuel consumption, which effects the operational cost of the plant significantly. The current study presents an overview about Outotec´s laboratory facilities and competence regarding the mixing and granulation of fines in different equipments. The usage of high intensity mixers (HIM) – vertical and horizontal as well – showed to be the most effective, based in cold agglomeration tests in small scale, in case of fine ore handling. Permeability and particle size distribution curves are used to evaluate and demonstrate the efficiency of the different equipments. Outotec´s ”Know-How” with the different type of mixer and the modern laboratory facilities provide an excellent opportunities to optimize the mixing and granulation procedure and utilize up to 100 % pellet feed

Aug 17, 2017

By Rodrigo Martins, Mauro Trindade

I Reduction of energy consumption in air compressors by the implementation of individualized load control. Reduction of 3,5% from Jun / 18.

Oct 3, 2019

By Marcelo Rebellato, Leonardo Silvestre, Zhang Yongqing, Felipe Bastos, Zhang Weiqiang

This work reviews the new version of GB1499.2-2018 Chinese national standard and specification, which governs the production of high-strength reinforcing hot rolled ribbed bars in China. In addition, it discusses the main concerns from Chinese rebar makers that might affect production and application of Nb-bearing rebars, like reheating temperature required to dissolve given niobium additions, the promotion of bainite microstructure and continuous yielding, as well as Nb strengthening effects. Through extensive investigation involving both thermomechanical laboratory simulations and industrial trial, the existing state and effects of Niobium along the reheating, rolling and cooling are illustrated. At the end, optimum processing conditions have been established to produce high strength rebars for the specified requirements. The adoption of new process conditions reflected in an amount of about 20.0 million tons of Nb-bearing rebar being produced in China in 2018 with required tensile properties and microstructure, and helped rebar makers to reduce production costs considerably. Based on production data, Niobium demonstrated positive strengthening effect for high strength rebars, in particular for small diameter rebars with earthquake resistant performance. What is more, the results of the research enrich the knowledge of the application of Niobium in steels when TMCP rolling is not used.

Oct 1, 2019

By Valdicleide Silva Mello

Nowadays the biodiesel use is obligate in Brazil, in order to reduce the emissions of fuel burn. However, it is important to analyze which percentage of biodiesel is necessary to keep or improve the lubricant action of fuel for diesel engine, as well which kind of biodiesel give better performance. Therefore, this work aims to analyze the parameters that keep the lubricant action of biofuels, by using the Box-Behnken design type to optimize them. In this design was evaluated the input parameters: the type of the biodiesel (soybean, sunflower and palm), the concentration (5%, 20% and 100%) and the temperature of contact (25°C, 40°C and 60°C). The analyzed output parameters were the percentage of film formation, coefficient of friction, wear scar diameter (WSD) of ball, these output parameters were obtained by HFRR tribometer and they were analyzed applying response surface methodology. With this methodology was possible to determine the simultaneous influence and the interactions between two or more independent variables investigated. The response surfaces generated for the coefficients of friction, WSD, film formation showed a higher lubricant action for higher levels of concentration of biodiesel. An increase in lubricant action was found to high and intermediate temperature.

Jul 31, 2018

By Luiz Peixoto, Andrea Falcon

There are a few ways to impact the capacity of a reciprocating compressor, by altering suction and discharge pressure and recirculation. By reducing the pressure drop in the section before the compressor it is possible to provide a higher suction pressure and subsequently achieve a higher compressor flow rate. The increase in the suction pressure while maintaining the discharge pressure reduced the demanded compressor Head. When considering oxygen compressors it is necessary to cautiously evaluate the safety norms and parameters due to the risk of explosions and fires due to high oxygen velocity.

Oct 3, 2019

By Flanelson Maciel Monteiro, Marcondes Mendes de Souza, Mauro Froes Meyer

This research is based on a bibliographical review of a field work that was done in the municipality of Parelhas / RN. The area explored, in turn, is known for its richness of mineral resources that are present in pegmatitic rocks. The general objective of this research is to characterize the main properties of the pegmatites and quartzite, in order to verify the heterogeneity of the elements, to raise a possible viability of extraction for economic purposes. The quartzite also presents a siliceous chemical composition. This rock is a source of bricks and silica refractories used in the steel industry and for the preparation of the blast furnace bed, ornamental rock used in different ways (rustic, carved, polished, among others). However, this research resulted in preliminary data, but it would be interesting to be more detailed in order to evaluate the economic viability of these rocks.

Oct 3, 2019

By Nelson SOUTO, Nicolas LEGRAND, Sami ABDELKHALEK, Zafer KOONT

A work roll thermal crown model has been developed for a wide range of hot and cold rolling mill applications. The model is extremely fast, robust and accurate to determine the evolution of thermal crown all along the rolling campaigns. It has also ability to consider work roll shifting, multiple segmented cooling zones along the length and circumference of the roll as well as composite rolls properties (e.g. different thermal properties between mandrel and core of the roll). Moreover, the model includes simultaneously fast and slow temperature evolution calculations, respectively near roll surface (skin area) and at a certain distance below the roll surface (bulk area). This gives to thermal crown predictions a higher accuracy than conventional thermal crown models from literature that consider only the slow temperature evolution regime. An optimization procedure together with roll surface temperature and roll thermal profile measurements have been used to tune the model. The tuned model applied to hot rolling conditions has shown a significant influence of roll shifting and composite rolls properties on the prediction of roll temperature distribution and thermal crown during rolling. The tuned model applied to cold rolling conditions highlights the importance of mill operators practices to modify cooling distribution across roll barrel length with the segmented cooling zones to adjust the thermal crown and to get better strip shape control.

Oct 1, 2019

By Luciana Lezira Pereira de Almeida

With the increasing use of ornamental rocks, mainly in civil construction, sundry problems were identified in relation to rocks cutting, such as efficiency in the cutting process and rock quality lumber. In recent years several composites have been developed to solve these problems. In this context, the study of the binomial matrix metal-diamond interaction is of paramount importance for the development of new composite materials to improve the efficiency of the cutting tool. The diamond impregnated matrix metal often reveals a reaction between the diamond surface and the matrix. Besides the mechanical connection, chemical reactions can sometimes occur. Therefore, this study aims to assess the achievement of diamond composites in the system Fe / Cu / Ni / Sn via powder metallurgy, with added CRB2. Analyzes have been performed to characterize chemical / physical and mechanical. The results have showed that addition of CRB2 promote significant changes in the properties of composites, especially in wear resistance and fracture toughness. Furthermore, the presence of the composite CRB2 causes a significant improvement in thermal stability.

Aug 16, 2017

By Frank Schrama

The Steel Plant Model (SPM) is an advanced logistic simulation model for steel plants. With the SPM, bottlenecks can be solved and logistics can be optimized. Both existing plants and greenfield designs can be simulated. All movements and actions simulated, from hot metal to cast products. Not only all major equipment and their relevant components (like a sublance) are simulated, but also ladles, scrap boxes, transfer cars and cranes. The whole plant is simulated in 3D and actual distances and speeds determine transport times. The SPM includes process time deviations and equipment downtimes for maintenance or unexpected breakdowns. This ensures more realistic and reliable results. Logistic optimization is based on comparison of different scenarios. For a new scenario, equipment and practices, etc. can easily be modified, added or removed. At the same time the SPM produces all relevant data for every new scenario, which can be presented conveniently. This makes the SPM the ultimate tool to find bottlenecks or optimize plant logistics. The SPM is validated for several plants world-wide, with different characteristics and layouts. The SPM not only realistically simulates existing plants with all utilizations, crane movements and waiting times, but also to accurately predicts the influence of plant modifications or unexpected events like breakdowns. Given the flexibility of the SPM, any (new) steel plant can be simulated quickly when a layout and the requested data are provided.

Aug 16, 2017

By Johanna Alegría-Ortega

Cr/CrN bilayer coating was deposited on AISI 440C by Cathodic Arc. The composition and structure of the Cr/CrN coating were investigated by scanning Electron Microscope, X-Ray Diffraction and X-ray Photoelectron Spectroscopy. The results show that crystal structure obtained was CrN phase with preferred [220] orientation. The hardness and adhesion of coating also were studied. The evaluation of erosion-corrosion (EC) on 440C bare and coated with Cr/CrN was performed by carrying out wear tests using a slurry jet with impingement angle 90° at 4 and 8 m/s. Corrosion, erosion and synergism wear rate were evaluated following the procedure described in ASTM G-119-09. This study presents that the synergism wear rate exceeds 40% of the total mass loss for coating and 60% of mass loss for the 440C, being the most aggressive wear component. The increase in impact velocity generated a rise in mass loss for both 440C bare and coated. The Cr/CrN coating offers better corrosion and erosion–corrosion resistance under all the tested conditions.

Aug 8, 2018

By Daniel Antonio Kapper Fabricio

A avaliação das propriedades de mecânica da fratura dos materiais é uma necessidade crescente, sobretudo no setor de óleo e gás. Esse cenário exige a garantia da qualidade na execução de ensaios de tenacidade à fratura. Esse trabalho tem como objetivo realizar uma comparação intralaboratorial para o ensaio de tenacidade à fratura KIC variando o executante do ensaio, visando atender ao requisito de garantia da qualidade da norma NBR ISO/IEC 17025. Os resultados foram comparados através de análise de variância. As diferenças entre os operadores não foram significativas frente ao erro residual a um nível de confiança de 95%, sendo tal resultado considerado satisfatório.

Aug 16, 2017

By M. A. Mekicha, M. B. de Rooij, C. Pelletier, D. T. A. Matthews

One of the main factors that reduce strip cleanliness are iron fines, which are formed due to the abrasive interactions of the roll surface and the strip in the roll bite during cold rolling. They can cause a problem in fouling of the cold rolling mill as well as downstream processes. It has been repeatedly observed that chrome plating the work roll improves strip cleanliness. In the present work, scratch tests and reciprocating sliding tests were carried out under lubricated conditions to explore the influence of chrome plating on iron fines formation. Scratch tests were conducted to study the influence of chrome plating on iron fines formation at single asperity scale due to its intrinsic property. Reciprocating sliding tests were performed to study the influence of chrome plating a rough surface on iron fines formation, taking into account the initial roughness. The scratches made using chrome plated pins showed lower friction, generated less iron fines and exhibited lower material transfer. Reciprocating sliding tests done using the uncoated pins showed galling at different sliding distances depending on the roughness of the pin. On the contrary, reciprocating sliding tests with the chrome plated pins exhibited no galling irrespective of the roughness.

Oct 1, 2019