Search Documents

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the virgin condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 69 to 258 MPa producing rupture times varying from 8 to about 4908 h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results mentioned in literature for the same material in the virgin condition.

Aug 16, 2017

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Aaron Samuel Young, Hiago Antunes Amador de Oliveira, William Pratt Rogers

Low commodity prices and lack of new high-grade deposits are pushing the mining industry for innovation. Lean mining has been vastly discussed in the past decades as a way to continuously improve mining efficiency. Although very theoretical, lean mining presents a set of new solutions enabled by the digital transformation that the mining industry is going through. This paper proposes a framework for a short interval control system with the purpose to allow timely responses by front line supervisors upon operational deviations. In the first part, the author briefly reviews concepts of short-range planning and lean mining. Then, the materials and methods used for the development of the short interval control system are discussed. Finally, alpha trial results are presented, and next steps discussed.

Oct 3, 2019

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Kazuya Nakabo

In this article, influences of restraint and MgO content on densification of alumina-magnesia castable during heating were experimentally studied. High thermal expansion-alumina-magnesia castable specimens were surrounded by low thermal expansion-alumina-silica castables, and heated in an electric furnace. Doing so allows restrained heating of alumina-magnesia castable. According to the results of simple calculations, the restraint stresses were estimated to be between 2 to 20 MPa, so the experimental conditions were considered reasonable. As a result of the experiments, it was verified that restraint densifies alumina-magnesia castable, resulting in an increase in modulus of rupture and modulus of elasticity. The densification effect of restraint became larger as the MgO content increased. The effects are attributable to an in-situ spinel forming reaction, which improves corrosion resistance.Taking the temperature distribution in the castable lining into account, large restraint stress is expected for the hot face while only a little effect is expected for back end. Thus, excessive difference in material property in the thickness direction, which is undesirable in terms of structural spalling, is a concern.Hence, the MgO content of alumina-magnesia castable should be determined carefully, taking not only corrosion resistance but also spalling resistance into consideration.

Oct 30, 2017

By Steven George Jansto

The hot ductility behavior of different microalloyed steel chemical compositions was examined simulating the thermal and strain conditions through the straightening or unbending section of the continuous casting machine. All samples were obtained from industrial slab casters ranging from 200 to 300 mm in slab thickness from steel mills throughout the world including China, Brazil, North America and Europe. The slabs were crack-free and hot rolled into prime quality products. No laboratory heats were tested. Although these microalloyed steels exhibit inherently lower hot ductility behavior, as measured by percent reduction in area at elevated temperature, these steels still exhibit sufficient ductility to satisfactorily meet the unbending stress and strain gradients existing in the straightening section of most casters. The majority of the published hot ductility data, as measured by % reduction in area (%RA), were based on laboratory heats and hence, are inaccurate in accessing the propensity for slab cracking on an industrial caster. This situation then results in invalid conclusions for different chemistries. This research has determined the minimum required %RA for crack-free casting is significantly lower than results based upon previously published laboratory generated data. For example, the literature quotes 40% RA minimum for Nb-bearing steels when in fact as low as 10% minimum RA is more than sufficient to assure crack-free casting based upon the extensive testing and analysis performed in this study. Instead of %RA, the measurement of strain energy has been introduced to evaluate hot ductility behavior. It is concluded that strain energy is a better measure of hot ductility behaviour than %RA. There is considerable value in the evaluation of the hot stress and strain curves, process metallurgy parameters and their relationship to slab quality instead of just basing hot ductility decisions on simple %RA measurements.

Aug 16, 2017

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Marjorie Benegra

This study aims to compare the wear resistance assessed in rubber wheel abrasion test of nickel aluminide coatings deposited by for Plasma Transferred Arc (PTA) and High Velocity Oxigen Fuel (HVOF) manufacturing, using the same raw material. A nickel aluminide powder was atomized and deposited on 316L steel plate substrate. After deposition, some specimens were submitted to a heat treating (1200 °C for 24 h followed by 760°C for 24 h). The coatings deposited using PTA developed different microstructures due to the incorporation of substrate elements, its performance was better than the HVOF coatings, although their Vickers hardness was similar. After heat treating, a significant variation in hardness and wear resistance was observed. For PTA specimens, there were decrease in hardness of 35%, while for HVOF ones this drop was approximately 20%. Nonetheless, the effect of thermal exposure in wear resistance was quite different: an increase of 21% was observed for HVOF coatings, while a reduction of 20% occurred in PTA ones. Microstructures modifications in PTA coatings were significant for their wear resistance. On the other hand, the reduction of porosity and sintering were responsible for a better performance of heat-treated HVOF coatings.

Jul 31, 2018

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Stefano Baf

This paper describes the main technical and process solutions applied to the extrathick and wide slab caster built at Yingkou (Liaoning, P.R. of China), as well as all the features required to achieve the surface and internal quality targets.

Aug 16, 2017

By João Luiz do Vale

In standard wear tests, such as pin on disk (ASTM-G99) or block on ring (ASTM-G77), the apparatus simulates conditions that are often different from a machine element real application. Therefore, for an accurate investigation of a tribological application, it is essential to test the real condition in which there are similarities as: geometry, contact details, force application mode, materials, among others. It emphasizes that for studies involving polymeric materials it becomes extremely relevant. Thus, the Laboratory of Surfaces and Contact (LASC) at UTFPR developed an apparatus for sliding bearing on shaft test. In that equipment, loads are applied by a dead-weight system and the frictional force is measured on a load cell. The apparatus operating ranges for load added to the dead weight system and rotation shaft are from 0.2 to 5.0 kgf and from 260 to 3500 rpm, respectively. This paper presents a detailed evaluation of such apparatus, which includes free-body diagrams analysis and a deduction to obtain an equation for the kinetic friction coefficient. Also, the standard measurement uncertainties of a caliper, an electronic scale, and a cell load were determined. It was verified that the kinetic friction coefficient equation is dependent on the apparatus geometry, the applied load, and the frictional force value. Additionally, through the statistical significance analysis it was concluded that some terms in the equation were not significant. Finally, through the application of the error propagation theory in the kinetic friction coefficient equation, the standard measurement uncertainty of the apparatus which showed a value nearby 0.002 along the operating range of the apparatus was obtained.

Jul 31, 2018

By J. Bas A. F. Smeulders

Traditional laboratory lubrication tests, including those for cold rolling lubricants often involve measurement of neat oils. To achieve increased levels of test severity, such tests are often carried out at high temperatures and prolonged durations. However, we found that the levels of lubricant degradation and wear in these tests can be much higher than in the field. Moreover, steel rolling is not done with neat oils, but with emulsions, where the presence of water influences film formation, surface chemistry and oil composition in the roll bite. To better approach the situation in the field, and thus to be able to develop rolling oils with improved lubrication performance, several lubrication tests were developed for emulsions: direct measurement of film formation and measurement of Stribeck curves, in which the emulsions can be assessed in terms of their boundary lubrication and elastohydrodynamic behaviour. The key innovation is that also another test method was developed, which focuses on boundary lubrication and wear, and the role of extreme pressure and anti-wear additives. Realistic levels of test severity are achieved in the tribometer by mimicking frictional power intensities and flash temperatures for typical cold rolling or tinplate mills. Test conditions can be adapted according to the mill stand or pass number and other cold rolling process parameters. The emulsions are kept at normal operational temperature. Clear differences could be observed between emulsions of various concentration and composition. The viability of the method is illustrated by a number of field cases, in which a good correlation is demonstrated between the laboratory tests and the performance in a pilot or production mill.

Jul 30, 2018