Search Documents

By Colin M. Sargent

THE electron diffraction pattern as seen in the electron microscope represents an approximately plane section of the reciprocal lattice. Identifying the zone axis of a diffraction pattern is often laborious for a crystal of low symmetry, especially if several crystal orientations are present. A program has been written in FORTRAN II (Version 2) for the IBM 1620 which will assist in plotting out reciprocal lattice sections. The calculation is performed by choosing a zone axis [uvw] and determining the d spacings and angle between the planes (Ow - v) and (wO - u). (This procedure is varied slightly for zone axes with Miller indices equal to zero.) Cartesian coordinates for the reciprocal lattice points are then calculated for these planes and for (ww— [u + v]). Any reciprocal lattice points within the parallelogram formed by the origin and these three points are then computed. The input and output are best described by use of an example (Monoclinic ZrO2) used in the author's work. Input consists of two cards: 1) The crystal parameters: a, b, c, a, 8, y, e.g., 5.1477, 5.2030, 5.3156, 90.000, 99.380, 90.000. 2) Three numbers, D, E, F, e.g., 5, 3, 3.0710-the first is the limit of the sum (u + v + w) considered; the second limits the absolute value of u, v, and w to (E- 1), e.g., 2, so that zones (221) would be the highest order considered in this example; the third, F, is the required constant, yL. Output is in the format shown in Table I. The reciprocal lattice sections may then be plotted on standard graph paper and compared with the unknown diffraction pattern. (Note that no attempt has been made to deal with systematically absent reflections.) A card deck for the program is available from Colin M. Sargent, ARZ, W-PAFB, Dayton, Ohio, 45433.

Jan 1, 1969

?AARONSON, ALFRED E , Vice-Pres , Mid-Co Petroleum Co, Mid-Co Bldg, Tulsa, Okla '18 ABADIE, EMILE R, Min Engr Address wanted '76 || ABADILLA, QUIRICO A, Geol Dept, Cia Mexicana de Petroleo "El Aguila," S A, Edifico "El Aguila," Esq, Calles Aurora y Comercio, Tampico, Tamaulipas, Mexico '20 ABBOTT, CLARENCE E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave, Bessemer, Ala '04 ABBOTT, LOUIS BENJAMIN, Chief Engr, Consolidation Coal Co, Elkhorn Div, Jenkins, Ky '15 ABBOTT, ROBERT R Met Engr, Peerless Motor Car Co, Cleveland, Ohio '12 ABE, ASAKA Fujita Min Co, Dojima, Osaka, Japan '14 ABEEL, GEORGE H, JR, Cons Min Engr, 635 St Paul Ave, Los Angeles, Cal '18 ABEL, ALBERT E, Asst to Pres, Valley Mould & Iron Corpn, Sharpsville, Pea '19 ABEL, W D, Min Engr Forum Bldg, Sacramento, Cal '19 ABELL, O J, Pres & Treas, Abell-Howe Co, 332 South Michigan Ave, Chicago, Ill '19 ABERNATHY G E Willow Springs, Mo '20

Jan 1, 1923

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson's ratio, and Young's modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young's modulus, s is Poisson's ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman's measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By Lane, K. S.

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse.

Jan 1, 1969

By AIME AIME

A FALL meeting that should have repercussions both in the "Transactions" and MINING AND METALLURGY was that of the Industrial Minerals Division (Nonmetallics) at Wilmington, Oct. 21-23; headquarters, Du Pont Hotel. The sixteen technical papers and two addresses were substantial and interesting. Moreover, in every instance but one, the author made the presentation, and the one exception must have been next of kin because the ensuing discussion indicated his command of the subject. The meeting schedule clicked at every turn, thanks to Dr. Gillson, chairman of the local committee, and even the four field trips adhered to the time table. The program pre-empted morning, noon, afternoon and night two general luncheons, two dinners, and an evening technical session reminding one of the Annual Meeting. Only the registration was disappointing - about 80.

Jan 1, 1943

By Jay F. Smith

The Alan Wood BOF Shop consists of two 140 ton furnaces with a rated yearly capacity of 1-1/4 million ingot tons, he hot metal for the BOF Shop is supplied by two 18 foot blast furnaces which produce an average of 2000 tons per day, To achieve the rated ingot ton capacity with this limited supply of hot metal, the preheating of scrap is necessary. This is accomplished in the furnace by using an oxygen-natural gas burner. Piping Arrangement The natural gas and oxygen are piped into the Shop through 8-inch lines to their respective valving stations. As can be seen from Figure 1, the flow of natural gas passes through a flow control valve which is common to both furnaces, after which it divides into two 6-inch lines forming two identical and independent gas control lines, one for each furnace.

Jan 1, 1972

By AIME AIME

IN accordance with the provisions of Art. XII, See. 3, of the By-laws of the American Institute of Mining and Metallurgical Engineers, the Board of Directors hereby give notice of their intention to amend the By-laws as follows : Art. V, Sec. 2. Amend by substituting the word "senior" for ('first" before the words "Vice-president" in line two of the third paragraph of said section which relates to the calling of special meetings of the Board in the absence or disability of the President.

Jan 1, 1930

Jan 1, 1885

By Walter A. English

CONTENTS PAGE Introduction. By WALTER A. ENGLISH 1 Theory of Seismic Reflection Prospecting. By WILLARD H. TRACY 2 Instruments for Reflection Seismograph Prospecting. By ARTHUR NOMANN 9 Seismograph Field Operations. By FRANK ITTNER 15 Determining Geologic Structure from Seismograph Records. By P. C. KELLY 22 INTRODUCTION BY WALTER A. ENGLISH,* MEMBER A.I.M.E. THE four papers making up this symposum have been prepared espe-cially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathe-matical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismo-graph exploration campaigns would do well to become familiar with as . much as possible of the technical aspects of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1939

By Dr. O’Neil Thomas J., Donald W. Gentry

It was a western truism that more money was made from selling mines than from buying them, just as it was accepted that many a good mine had been spoiled by working it. from R. E. White, "The Mining Town," Alta California August 18,1873 INTRODUCTION One of the most important aspects of mineral enterprises of US corporations is the influence of the depletion allowance on cash flow. This allowance permits mineral producers to claim sizable federal income tax deductions not available to other industries, and these deductions significantly increase cash flows in mining. In the past several years the minerals depletion allowance has come under increasingly heavy fire from many sectors as a tax loophole that deprives the federal government of large amounts of revenue. One estimate of the loss of tax dollars in 1968 was $2.25 billion due to depletion deductions and intangible expenses in the oil industry. Largely on the basis of such arguments, the Tax Reform Act of 1969 reduced percentage depletion rates for a number of minerals, and the Tax Reduction Act of 1975 totally eliminated statutory depletion for most oil and gas. In regard to percentage depletion for hard minerals, the federal government has estimated its resulting loss of revenue at $1.75 billion for 1980. The TEFRA legislation of 1982 further reduced the statutory depletion allowance available to iron ore, coal, and lignite beginning in 1984. Thus, it is clear that minerals engineers and managers should have a thorough knowledge of the origin, evolution, justification, and computational procedures relating to the depletion allowance. ORIGIN AND EVOLUTION OF THE DEPLETION ALLOWANCE

Jan 1, 1984

By F. L. Sizer

SOME old-time views which have recently come into my possession have inspired me to record that part of the early history of Leadville, Color- ado, with which I am familiar, the years 1878 to 1882, in the hope that others will add to what is here mentioned. My first appearance in Leadville was in June, 1878, immediately after graduation from the University of Michigan, and I found a congenial and lively crowd of young men, already there. The old log hotel, at the corner of Pine and State streets, housed some distinguished guests in the summer and fall of 1878. It was my good fortune there to make the acquaintance of James B. Grant, afterwards Governor of Colorado, in July of that year, when we were both glad of the accommodation afforded by cots in the second floor loft of the hostelry presided over by Herman Hibschle. Grant was then building his smelter and our associates were Eddy and James, August R. Meyer, and Berdell and Witherell. The Grand Hotel-Harris and Walsh, pro- prietors-was the first-class hotel of the place; but in a very few months there were many competitors.

Jan 1, 1924

Jan 1, 1893

Abbey, Robert Graham, District Mgr.. The W. W. Sly Mfg. Co., 50 Church St.. New York, N. Y. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd Concepcion del Oro, Zac., Mexico. '28 Abbott, Argyle Campbell, Dev. Dept., E. I. du Pont de Nemours & Co., Wilmington, Del. '29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg.. Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Elkhorn Div., Consolidation Coal Co., Jenkins, Ky. '16 Abeel, George H., Jr., Cons. Min. Engr Box 427, Santa Monica, Cal. '18 Abel, Albert E., Asst. to Pres., Valley Mould & Iron Corp Hubbard, Ohio. '19 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh. Pa. '28 Abeel, Leo M., Research Engr., Sullivan Concentrator Chapman Camp, B. C., Canada. '31

Jan 1, 1932

By Joseph Pogue

THE writer visited the Muzo emerald mines in July, 1915, and spent six days in their study. This paper embodies the results of his observations, plus information personally communicated by Robert Scheibe, FIG. 1.-SKETCH MAP SHOWING APPROXIMATE LOCATIONS OF ALL IMPORTANT EMERALD MINES AND PROSPECTS IN COLOMBIA. (Data in part supplied by Robert Scheibe, July, 1915.) Professor of Geology in the Mining Academy of Berlin, who at the time of the visit was completing a detailed field investigation of nearly a year's duration of the emerald deposits of Colombia. An elaborate account of this valuable work may be expected at a future date from the pen of Professor Scheibe.

Jan 5, 1916

By LEE H. CORNELL

Drilling activity in Kansas during 1945 continued at an accelerated pace to meet the demands of war; 1810 tests were drilled as compared with 1856 tests the previous year, 1771 tests in 1943, and 1516 tests in 1942. During the year 31 new oil pools and 10 new gas pools were discovered. Of a total of 364 wildcats drilled, 323 were dry; and of 1446 tests drilled in pools, 825 were oil wells, 197 gas wells, and 425 dry holes.

Jan 1, 1946

President MRS. REED W. HYDE 84 Mountain Ave. Summit, N. J. First Vice-President MRS, WILLIAM A. SCHEUCH Trent St. Great Kills, S. I., N. Y. Second Vice-President MRS. THORNS E. LLOYD Box B Netcong, N. J. Third Vice-President MRS. H.. T. HAMILTON 24 Ridge Rd. Summit, N. J.' Fourth. Vice-President MRS. R. A. PALLANCH 1342 Laird Ave. Salt Lake City, Utah

Jan 1, 1939

By AIME AIME

HONORARY COMMITTEE. HON. C. D. WALCOTT (Chairman.), Director U. S. Geological Surrey. HON. FREDERICK I. ALLEN, Commissioner of Patents. DR. FRANK BAKER, Superintendent National Zoological Park. MR. CHARLES A. BELL, President American Security and Trust Co. MAJOR JOHN BIDDLE, Engineer Commissioner of District of Columbia. ADMIRAL C. M. CHESTER, Superintendent U.S. Naval Observatory. GENERAL WILLIAM CROZIER, Chief of Ordnance, U. S. A. ADMIRAL GEORGE DEWEY, Admiral of the Navy. COLONEL CLARENCE R. EDWARDS, Chief Bureau. of Insular Affairs. MR. WILLIAM C. FOX, Director Bureau of American Republics. MR. CHARLES C. GLOVER, President The Riggs National Bank. GENERAL A. W. GREELY, Chief Signal Officer, U. S. A. MR. BERNARD R. GREEN, Superintendent Library Building. GEN. G. H. HARRIES, Vice-President Washington Electric Railway Co. HON. E. A. HITCHCOCK, Secretary of the Interior. COMMANDER H. M. HODGES, Chief Hydrographer, U. S. N. PROF. W. H. HOLMES, Chief Bureau of American. Ethnology. PROF. S. P. LANGLEY, Secretary Smithsonian Institution. GENERAL ALEXANDER MACKENZIE, Chief of Engineers, U. S. A. ADMIRAL N. E. MASON, Chief Bureau of Ordnance, U. S. HON. WM. M. MEREDITH, Director Bureau of Engraving and Printing. HON. V. H. METCALF, Secretary Department of Commerce and Labor. HON. WILLIS L. MOORE, Chief -U. S. Weather Bureau. HON. PAUL MORTON, Secretary of the Navy. MR. F. H. NEWELL, Chief Reclamation Service, U. S. Geological Survey. HON. S. N. D. NORTH, Director Census Office. CAPT. E. C. PENDLETON, Superintendent Naval Gun Factory. MR. GIFFORD PINCHOT, Chief Forester, Department of Agriculture. MR. HERBERT PUTNAM, Librarian of Congress. ADMIRAL CHAS. W. RAE, Chief Bureau of Steam Engineering, U. S. A: MR. RICHARD RATHBUN, Assistant Secretary Smithsonian. Institution. HON. W. T. RICHARDS, Commissioner General Land Office.

Jul 1, 1905

By R. E. Ogilvie, J. I. Goldstein

The a and y solubility limits in the Fe-Ni phase diagram have been redetermined at temperatures above 500°C. Both a diffusion-couple and a quench and anneal technique were used. The solubility limits were measured with an electron-probe micro-analyzer. The nickel concentration at the phase boundary is increased below 700°C and the a solid-solubility range is much larger than had been previously measured. The solubility limits are also extrapolated to 300°C. It is suggested that the solubility of nickel in a FeNi reaches a maximum in the temperature interval 400o to 500°C. THE equilibrium diagram has been of great use in the field of meteoritics, where the phase relations between kamacite (a) and taenite (?) in metallic meteorites can be described by means of the Fe-Ni diagram. The study of metallic meteorites by electron-probe microanalysis has cast some doubt on the accuracy of the presently available Fe-Ni diagrams.1, 2 Recent thermodynamic studies of the Fe-Ni system also suggest that the diagram may be in error.3 For these reasons the high-temperature (800o to 500°C) part of the diagram was redetermined. INTRODUCTION The currently accepted Fe-Ni diagram is that of Owen and Liu.4 Above 910°C, there is a region of complete solid solubility, ? (fee). Below 910°C, the a (bee) phase is stable in pure iron. The effect of increasing amounts of nickel is to stabilize the y phase. The phases that form when Fe-Ni alloys are heated or cooled bear little relation to the equilibrium diagram. If an alloy is cooled from the y state and held at a temperature within the a + y field, no evidence has been found for the occurrence of the y - a transformation.5 If the alloy is cooled to low enough temperatures the y phase breaks down into a supersaturated bee phase called a2. In fact, in alloys over 27 pet Ni the y phase is retained at room temperature.6 The a, phase has the same composition as the original y. The temperature at which a2 forms, the M, temperature, has been determined experimentally.' A state of equilibrium can be approached by cooling below M, to form a2 and then reheating the alloy into the two-phase region of the diagram. The y phase will then begin to precipitate out of the a2 phase and grow. The growth of the phase, however, is quite slow. Using the interdiffusion coefficients -Da of Goldstein et al.,8 it is estimated that it takes about 1 year to grow a 10-µ-wide region of ? at 700°C in a 5 pet Ni alloy. Owen and Liu4 used the technique just described to form the equilibrium phases. The phases present were determined by means of X-ray analysis. The accuracy of their diagram depends on the number of alloys available near the phase boundary at a given temperature. In this study two different techniques were used to determine the a/a + ? and ?/a + ? solubility limits. The inherent accuracy of both techniques was greatly improved over that used by previous investigators because the phase-boundary compositions were measured with an electron-probe microanalyzer. PROCEDURE The two methods used to determine the Fe-Ni diagram are the diffusion couple (D.C.) and the quench-and-anneal (Q.+A.) techniques. In the first method, diffusion couples whose diffusion path goes through a two-phase region of the phase diagram were used. A description of the technique used for making the diffusion couples has been described in a previous paper.' After the diffusion treatment a discontinuity in the resultant concentration vs distance profile was measured. The nickel concentrations in the a and ? phases at the interface of the discontinuity are the solubility limits of the a and ? phases in the phase diagram at the diffusion temperature. If the interface com-

Jan 1, 1965

COMMITTEE OF ARRANGEMENTS. General Committee.-J. F. Lewis, Quinnimont, W. Va. Committee of Reception at Staunton.-Major Jed. Hotchkiss, Chairman ; W. A. Burke, M. E. Miller, R. N. Catlett, W. J. Nelson, J. T. Effinger, D. A. Kayser. Local Committee of Arrangements.-G. T. Wickes, Low Moor, Chairman; G. W. Bramwell, Stone Cliff, Secretary; J. E. Johnson, Longdale; H. Firm¬stone, Longdale; S. F. Morris, Quinnimont; O. A. Randall, Ferrol; William N. Page, Ansted; F. Lyman, Low Moor; S. M. Buck, Coalburgh; E. S. Hutchinson, Cannelton ; M. F. Maury, Saltpetre Cave. THE opening session of the Institute was held at Staunton, on Monday evening, May 30th, in the Opera House. Major Jed. Hotchkiss, Chairman of the Committee of Reception, called the meeting to order and introduced Mayor Balthis, who spoke a few words of welcome to the members present, and then introduced the Hon. A. H. H. Stuart. Mr. Stuart in addressing a formal welcome to the Institute to the " little city of the mountains," spoke of the value of the services of the mining engineer in developing the mineral wealth of Virginia and in solving the problems of her geological history. Mr. Metcalf, President of the Institute, replied on behalf of the Institute to the cordial welcome of the mayor and Mr. Stuart, and then read an inaugural address on Force. At the conclusion of the President's address the following papers were read The Electrolytic Determination of Copper and the Formation and Composition of so-called Allotropic Copper, by J. B. Mackintosh, Hoboken, N. J. Read by Professor Egleston. The New Unpublished Map of Chester County, Pa., by Professor Persifor Frazer, Philadelphia. The second session was held at the Opera House on Tuesday morning. The papers read at this session were: Investigations on the Ore Knob Copper Process, by Professor Thomas Egleston, School of Mines, New York city. A Volumetric Estimation of Manganese in Pig Iron and Steel, by F. H. Williams, Vulcan Steel Works, St. Louis, Mo. Read by the Secretary.

Jan 1, 1882

Jan 1, 1884